Search Documents

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

Separation in magnetic fluids is one of the modern techniques that offer a unique approach to material manipulation in a broad spectrum of industries. Its wide-scale application has been restricted so far for a variety of reasons, including limited throughput, inefficient recovery of magnetic fluids and the cost of commercially available magnetic fluids. This situation has changed recently. Very selective separators, with automated density control, capable of treating a variety of materials in a wide spectrum of densities and particle sizes have been built by DebTech and applied in the diamond industry. Technology for the recovery of magnetic fluids has been developed and low-cost magnetic fluids, with high magnetisation and low viscosity are being produced on a production scale. Scale-up of the technology has been addressed and units capable of treating large tonnages of material have been designed. Such a development thus offers the minerals industry a technology that surpasses the existing technologies in selectivity, efficiency and versatility

Jan 1, 2000

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992

Interest in those physical properties of minerals which might be used to good effect in prospecting is not new. Early in the nineteenth century attempts were made in th'e Cornish mines to measure the natural electric potentials set up by chemical changes proceeding in the lodes. The distortion of the earth's magnetic field by bodies of strongly magnetic iron ore received early recognition in Sweden. Treasure-finders, working on the principle of electrical induction, appear to have been invented about eighty years ago, though were probably not then applied to mineral exploration. By the end of the nineteenth century Eotvos, a Hungarian physicist, had constructed a highly sensitive type of torsion balance capable of measuring the minute distortions in the earth's field of gravitation resulting from variations in the density of the materials composing the crust. During the first decade of this century he demonstrated its value in tracing rock-salt deposits in virtue of their low density compared with the surrounding rocks. Geophysical prospecting began to be recognised as having a very definite value and its development gathered momentum. Its great expansion took place after the 1914-18 war, when its value in oil exploration was amply demonstrated, and this expansion has continued to the present time and shows no signs of abating.Divisions of Applied Geophysics.The four main divisions of applied geophysics are electrical, magnetic gravitational and seismic. With the importance of ores of radio-active metals, one might add to these a radio-active division. The first two are more important to the field of mining, but techniques based on gravitational attraction have their uses in particular cases. Seismic methods are not generally suited to the exploration of metallic ores, but have proved of enormous value in the search for petroleum. With vast quantities of oil as the prize, more money has been lavished on the deve10pment and practice of these methods than on all the others put together.Geophysical Prospecting Methods.Geophysical prospecting methods may be used to detect a mineral deposit directly in virtue of differences in the intensity of some physical attribute common to it and the enclosing country rock. Examples of this are the detection of rock-salt by gravity measurements, or of iron ore by magnetic methods. Of much wider application, however, is the indireot approach in which the aim is to determine, by geophysical means, the geological structures controlling the disposition of mineral deposits. These structures may be partly known from geological work, in which case geophysical methods are useful adjuncts. Where, because of an 'unbroken cover of overburden, no useful geological information presents itself, scout drilling or geophysical prospecting are the only alternatives. Overburden is here intended to mean any covering material not, involved in the structures controlling the mineral deposits. Prospecting for petroleum amounts to the detecting of favourable reservoir structures, and as the chief types of such are the same the world over...

Jan 1, 1950

By Ranford LC

Modern, research-based approaches to mineral exploration are essential to the future maintenance of the mineral industry. These need to fully utilise the rapidly expanding growth of understanding of the evolution of the earth's crust, and be properly integrated with advances in understanding of chemical and physical processes involved in ore formation. BMR has a major role to play in supporting the growth and utilisation of this research base, as well as maintaining the national geological and geophysical bases which are essential both to tactical and strategic interests of Australia and of its mineral industry. The objective development of data-process modelling is one target of such strategic research based on a more integrated approach to research by BMR, mineral companies, CSIRO and the universities with emphasis given to promoting positive feedback during research activities. Examples of the success of strategic research in Australia and overseas are noted in the Text.

Jan 1, 1986

By Adamiak Z. P

A study has been made of the influence of bentonite type on the wet strengths, dry strengths and drying rates of pressed iron ore pellets. Measurements of the influence of bentonite on the kinetics of growth of pellets are also reported. The results show that bentonite decreases the rate of growth of pellets and the drying rates of pellets while increases are observed in both wet and dry strengths. The results have been interpreted in terms of the physical and chemical charact- istics of the bentonite and the suitability of a given bentonite for particular pelletising operations has been discussed.

Jan 1, 1973

The Tavua Power Proprietary Ltd. was created in 1936 for the purpose of supplying electric power, compressed air and water to the mining field.The original share capital was subscribed on a two-third:one-third basis by the Emperor Gold Mining Company Ltd. and Loloma (Fiji) Gold Mines, N.L. In 1940, Fiji Mines Development Ltd. (later changed to Dolphin Mines Ltd.) was admitted as a shareholder, and, in 1950, a further change occurred. The present shareholding in the Company is as follows:A central power station was decided upon to reticulate power and compressed air over the whole field and building commenced in May 1936.The original plant comprised three Belliss and Morcom diesel generating sets 770 b.h.p. 525 kW 3,300 V, 3 phase, 50 cycle; one Belliss and Morcom diesel compressor set 2,09'0 cu. ft. of free air per min. at 90 lb. gauge 300 r.p.m., and two small Ruston-Holman diesel compressor sets each of 525 cu. ft. capacity taken over from Loloma (Fiji) Gold Mines, N.L., and the then existing Koroere Gold Mining Company.BuildingThe original building was 130 ft. long by 47 ft. wide with an elevated switchgear annex on the west side from which a clear view of the engine room is available.

Jan 1, 1953

By T

THE Sulphide Corporation's works for the smelting of ores containing lead, gold, and silver are situated close to the Cockle Creek railway station, on the main Northern railway line, and are about 95 miles from Sydney and 10 miles from Newcastle. A branch line runs to the works, and siding accommodation and bins are provided for expeditiously handling all ores sent for treatment. The Corporation also possesses wharfage facilities at the port of Newcastle, where consignments of ores arriving by sea can be handled direct into railway trucks for conveyance to the works.The greater portion of the ore treated at Cockle Creek comes from the Corporation's mine at Broken Hill, but a large quantity of other grades is also purchased and treated.

Jan 1, 1918

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

For its Hellyer project, Aberfoyle sought to establish a high degree of confidence in all aspects of the feasibility study. Accurate capital and operating cost estimates were an integral and essential part of the study. They were crucial to the evaluation of investment returns and competitive cost position. Both the capital and operating cost estimates were based on the comprehensive data available from exploratory mine development, pilot plant operation, detailed engineering design, and Aberfoyle's experience in the area. One of the principal project objectives was to maximise operating productivity and efficiencies and this created capital cost alternatives which needed thorough cost-benefit assessment. The estimated capital cost for construction and development was $90 million, and the project was completed virtually on time for $80 million. The first year's experience indicated that operating costs would settle to well within 10% of the estimates.

Jan 1, 1990

By P Barrette

The manual gravimetric drying moisture determination methods currently employed by most mineral processing plants fail to provide timely and accurate information required for automatic control. The costs associated with transporting and handling concentrates represent a major portion of the overall treatment price. When considering the cash flow of a mining operation that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, any tool that provides real-time feedback on the process is vital (Edwards, RP 1994). The introduction of an on-line moisture sensor would become a welcome addition to the process control field instrumentation package now applied. A novel on-line determination system for ore concentrate moisture content would replace the tedious manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum. Therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the æwish listÆ of mineral processors since the problem has always been that you can only control what you can measure, (Konigsmann, 1990). Today, the task of moisture determination is still done by the classical technique of loss in weight utilising uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of seven to nine percent, but controlling the moisture content below eight percent is a difficult task with a manually controlled system. Many times, delays in manually achieving reliable feedback of the moisture content results in the moisture varying from five to twelve percent before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper introduces and describes a unique and promising novel on-line moisture sensor employed for mineral processing de-watering applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimisation of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarise the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content. The commercial model of the equipment is described with the features and benefits to the users summarised.

Jan 1, 2003

The papers in this section of the conference and indeed the conference as a whole will rightly focus on the recent û the state of play around the Pacific Rim. However, to set the scene I propose to take a longer-term perspective. In so doing I wish to illustrate and emphasise that change is normal and natural û to paraphrase Bob DylanÆs 1963 classic, æThe times they are (always) a-changinÆ Æ. The challenge is how to cope with such change, in an industry, a corporate and a personal sense. A further challenge for geologists, both exploration and mine-based, and indeed for anyone, is to understand where they fit in the broader picture. For several reasons it is appropriate first to look briefly at the minerals industry in the Pacific Rim around a century ago. It was here in Adelaide in April 1893 that the first general meeting of the Australasian Institute of Mining Engineers (or The Australasian Institute of Mining and Metallurgy as it later became) took place and where the Centenary Meeting was held in 1993. The late 1800s and early 1900s was a period of extraordinary change in the minerals industry regionally and worldwide. The industry benefited from the economies of scale provided by improved mechanisation. It further benefited from the introduction of technically qualified professionals, such as chemists, metallurgists and mining engineers, although the usefulness of geologists had yet to be recognised commercially. With the rise of such professionals, technical societies formed and flourished. At the same time international financial markets and trade were expanding, a gold standard was widely supported and the financing of mining ventures was well established. Mining was an international business and its people travelled widely. As a consequence of the better-educated mining professional, the ready exchange of knowledge and the availability of finance, new processing techniques such as pyritic smelting, the cyanide process and flotation were developed. These, together with much improved materials handling in the mining and processing phases, dramatically changed the economics of the minerals industry.

Jan 1, 2004

By Dhar B. B, Gupta R. C

Grinding of iron ore is an essential step to utilise ore fines for pelletisation needed for DRI units. While preparing iron ore pellets for DRI production, the iron ore needs extensive grinding which is highly energy consuming step causing the process to become non-viable in some cases. In the present paper an attempt has been made to evaluate grinding performance of thermally treated ore compared to normal ore grinding. Such thermal pre-treatment has been found to reduce the energy requirement with lower consumption rate of grinding media. It has been observed that by applying thermal shock the ore is rendered weak with improved grindability. The stresses generated due to thermal treatment may extend existing micro-cracks in the ore and in some cases it may even nucleate fresh cracks. Experimental studies carried out on thermally treated hematitite ore reveals that the heating to 400¦C followed by water quenching can cause a reduction of 45 per cent in grinding energy. The paper gives the details of the experiment and the Results.

Jan 1, 1999

By Dawson RD

For the past 45 years, the casting of refined lead ingots by The Broken Hill Asso- ciated Smelters Pty. Ltd. (B.H.A,S,) at Port Pirie has been mainly by use of manually operated rotary casting wheels of Newnam design. This style of operation was quite satisfactory as far as standard of product was concerned, but was manually intensive and a relatively high cost operation. With most other large scale lead producers already using automated-casting equipment, an investigation which commenced in 1966, progressed through stages of enquiry, design and development until the present plant commenced trial operations in late 1973, and fully operative in late 1974. While certain features of the plant are sed on overseas practices the plant was signed and built within Australia to BRAS ecifications. As constructed it consists two almost identical casting lines each pable of producing 25 kg ingots at 25 tonnes r hour using straight line casting machines d automated stacking weighing and strapping

Jan 1, 1975

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99· 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

By N Phillips

Fosterville gold mine recently celebrated production of its one millionth ounce of gold based firmly within a history of refractory sulfide gold mining. Compared with other Victorian gold mines, the disseminated nature of the sulfide gold is a deposit style with low estimation variance combined with established processes to accurately delineate the controlling structures. The systems in place had been established and have worked effectively for the majority of the one million produced ounces.By the end of 2014, diamond drill campaigns targeting the lower Phoenix orebody at depths of 800 m below surface began showing a change to the nature of the gold within the deposit. Coarse visible gold within 0.5–2 m thick quartz carbonate veins were being intersected with regularity showing the emergence of a different zone of gold mineralisation.Data about the new and exciting discovery couldn’t be gathered fast enough, however, established systems and processes throughout the geology and processing departments were not developed to handle a coarse gold environment. Change would be commensurate with the size and scale of the discovery, and new learnings would need to be implemented quickly to keep in front of a mining schedule that was focused on producing tonnes due to the dropping grades of the sulfide ore.Gold assays being returned were showing that the gold nature was different to those of other Victorian deposits. Comparative to the highly nuggety nature of gold found in other Victorian goldfields, the fine grained gold accumulations were dispersed in relatively consistent narrow linear trends grading consistently into the hundreds of grams per tonne. New drill intersections were being returned by the day and research to find developed orebodies that had published information into how to handle such a rapid change yielded few examples.The challenge was to review and set new standards with regards to handling an orebody that transitioned the very nature of the gold being mined. This involved reviewing all steps in the estimation process including data capture and quality control and quality assurance through to mineral liberation through the mill. Difficulties also involved finding analogous orebodies that consisted of both free milling and refractory ores that were dealing with drill assays that were measured as percentages of gold.CITATION:Phillips, N, 2017. Fosterville gold mine – breaking the mould for Victorian gold, in Proceedings Tenth International Mining Geology Conference 2017, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

By M Lewis, A Cook

This paper is based on the technology and functionality of a Modular Mining IntelliMINE« system which is a real-time decision-making tool. The IntelliMINE« system, incorporating Dispatch, is a fully Integrated Mine Management System. Measuring, quantifying and analysing the performance of mining is considered a fundamental and strategic step towards changing the nature of technical and operational decision-making at the majority of international mining corporations. Successful implementation of electronic data capture devices and computerised tools have enabled many mining operations to improve their competitive position with an improvement in the utilisation of the key assets, mineral resources, capital mining equipment and human resources. Real Time Mine Management Systems are designed to direct the emphasis away from collecting data and focus decision makers on the real issues with well-presented and reliable information. The systems provide a common stream of information to enable senior management, operations, maintenance, technical and process plant staff to make complementary decisions based on reliable, accurate and timely data. The mine asset information tools focus all employees on performance and give them feedback on their area of responsibility. The resulting tangible benefits can be delivered in different forms depending on the mining method, ore type, workplace culture and the current competitive position. Typical areas of improvement reported by system users are:reduction in capital expenditure on mining equipment fleets; more effective planning and budgeting parameters and procedures; increased control over ore-extraction and processing; increased employee accountability and organisational performance; and improved co-ordination between planning, operations, maintenance and processing. These improvements can be delivered in different forms depending on the status of the mine and commodity markets. In times of market oversupply and low commodity prices, the benefits can be delivered to the bottom line in terms of reduced cash costs, reduced capital and operating resources to maintain constant production. In times of market expansion, existing capital resources will be more productive delivering increased production and revenue. Mine management systems have the potential to transform a traditional mine operation into a learning organisation with an improved understanding of the critical performance issues and enable development of relevant strategies to continually identify and eliminate operational inefficiencies. The effectiveness of each strategy and operational change can be accurately monitored and its success (or otherwise) will be quantified. The latest downturn in the world metal prices has forced many mining companies to focus on cost reduction and productivity improvements as a means of remaining competitive. Maintenance represents a significant proportion of the overall operating costs in the mining industry. A structured proactive maintenance approach such as Reliability Centered Maintenance (RCM) can achieve significant cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production.

Jan 1, 2000

THE object of the air-tight stopping is either to prevent a current of fresh air from getting into the fire area, or to prevent an escape of fumes and gases from the fire area into the workings of the mine. In the former case all is "plain sailing," but in the latter case there are certain difficulties to be overcome.In the Broken Hill Proprietary mine there were two styles of stopping used during the last fire-brick and bag and the following were the chief points that determined the use of one in preference to the other:-If the required stopping were to be more or less permanent, bricks were used, also if the area to be blocked were large-bricks being so much lighter and easier to handle than bags filled with -skimps. If, however, the air contained much gas, a bag stopping was put up. Great difficulty was experienced in getting essentially surface men, such as bricklayers, to work where there was the; slightest trace of gas; miners, however, would willingly do the work, and a bag stopping could be built without skilled labour.In old drives and gangways, where there was the liability of settlement, the bag stoppings were preferable to brick. The slightest movement around the sides or foundations of the latter would cause cracks, thus rendering the brick stopping useless;whereas, in the former, there was a certain amount of elasticity.

Jan 1, 1909

By Jamsa-Jouneia SL, Lahteenmaki S

Sophisticated control systems require sufficient and reliable information from the process to be controlled. At the Pyhasalmi concentrator two novel measurements, a particle size indicator (PSI) and a mill level monitor (MLM), have led to significant progress in the control of the grinding circuit. The PSI and the MLM measurements have brought additional information from the process. The PSI has been an absolute prerequisite for determining the overall grinding circuit efficiency and the design of the integrated grinding and flotation control system. The MLM measurement has enabled studies on the volumetric filling of a mill to be utilised for maximising the mill throughput. The paper describes the operation principles of the PSI and MLM devices and the additional process information received. The results of a metallurgical pre-control audit are discussed and finally the design of the integrated control system is outlined.

Jan 1, 1993