Search Documents

Environmental considerations were key factors in the design of the Ranger Uranium Mines treatment plant. The mine is located adjacent to the Kakadu National Park and has an average rainfall of 1.6m per annum. Initially, no contaminated water or liquid effluents are to be released from the project area and thus water management is a key design and operating fact. Particulate and gas emission criteria influenced design as did occupational hygiene factors (dust, radon, housekeeping, maintenance access). Equipment selection and engineering standards were conservative and resulted in the plant attaining design performance in less than three months from the date of commissioning. A number of mechanical and operational problems were experienced and are discussed in the paper, however none of these problems have had a significant effect on production.

Jan 1, 1984

By R G. Richards

The Australian glass sand industry produces some 2.8 million tonnes per annum of silica sand, of which about 2.0 million tonnes are exported and the rest is for the domestic market. Approximate production rates for each Australian state are listed. The variety of processing methods used in the currently exploited deposits reflects the size, location, and characteristics of the various deposits and the requirement of the end market/s. The industry uses to a large extent equipment developed for the separation of mineral sands, particularly as it applies to low grade heavy mineral deposits, where low cost, high capacity and metallurgically efficient equipment has proved eminently suitable for the production of the low value glass sands. The requirements of the domestic market, as well as those of the present and potential export markets are discussed covering quality requirements, distribution channels and other factors critical to success.

Jan 1, 1990

By Salehi M. R

Although inherent mineral matter appears to have no effect of the reflectivity of inertinite in the reflecting light microscope, it has a marked effect on the grey levels resulting from the backscattered electron response in the scanning electron microscope. Inertinite with a high inherent mineral matter content has a high grey level response but not as high as that of mineral matter. The highest grey level response is with inertodetrinite which at times could be mistaken for mineral matter. Fusinite has a higher grey level response than semi-fusinite. The backscattered electron grey level response corresponds to average atomic number and hence approximately to density. If a porous structure develops and becomes filled with mineral matter such as S, Cl, Ca, Si, and Al the grey level will be higher. Micrinite has an unusual response in that it behaves like an exinite maceral in the SEM rather than an inertinite maceral. It either has a low grey level when relatively free of inherent mineral matter, or a low grey level background with high level granules corresponding to Si and Al dominantly. Similar structures have been found in exsudatinite and resinite. It is thought that micrinite results from the migration of hydrocarbons out of exinite giving a porous structure which usually accommodates inorganic matter.

Jan 1, 1991

By J L. Carpenter, S M. Iveson, K P. Galvin

Wet beneficiation of iron ore fines less than 1 mm typically involves a desliming stage ahead of the fine gravity separation such as spirals. The desliming is achieved using a bank of cyclones. The reject ultra-fines emerge in the overflow stream at relatively low pulp density, contain high proportions of low-value slimes, but also well-liberated iron ore ultra-fines below 0.045 mm in size; however, recovering the valuable iron ore ultra-fines from this overflow stream presents a significant challenge due to the need to remove such a large amount of water and slimes.The REFLUX™ Graviton consists of distinct 3D-printed modular units, based on REFLUX™ Classifiers, which are rotated at high speed in a large centrifuge. This system has previously been investigated under semi-batch conditions, demonstrating the potential for precision separations with significant capacity. It has been shown that the throughput advantage of the inclined channels and G forces multiply. This is the first paper presented showing the performance of this system under continuous steady-state conditions. Ultra-fine silica in the size range of 0 to 0.045 mm was fed to the Graviton at different volumetric rates, fluidisation rates and pulp densities ranging from 2 wt per cent to 30 wt per cent, in order to develop a fundamental understanding of the system’s performance. Experiments were then repeated using ultra-fine iron ore.CITATION:Carpenter, J L, Iveson, S M and Galvin, K P, 2017. Separation of ultra-fine particles using the REFLUX™ Graviton, in Proceedings Iron Ore 2017, pp 141–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

Study on Flotation Experiment of Complex Copper-Lead-Zinc Polymetallic Sulfide Ore in High Altitude Area and its Industrial Application

Sep 13, 2010

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Brien R. J, O&apos

Faster and more efficient methods of producing and refining iron and steel are imposing severe conditions on the refractory materials used to contain these metals in the molten state. In order to provide refractory linings which will give the desired service life and maintain unit availability at an economical level, it is necessary to appreciate the aggressive environment in which the refractories operate and determine the reaction mechanisms by which the refractories are destroyed. Only by such studies can the most suitable refractory or refractory combination for a particular unit be selected. Examples of refractories selection and reaction mechanisms are discussed for blast furnaces, BOS vessels, AOD vessels, steel ladles, vacuum degassing units and continuous casting.

Jan 1, 1976

By D Syme

In the middle of 2000, BHP Billiton implemented a Six Sigma Plus business improvement program known as Operating Excellence. It was developed based on a business bottom line initiative to deliver 35 - 40c/share and was one of the BHP Billiton strategies to deliver $2 earnings per share and a longer term $40 share price (BHP share price). Cannington is a silver, lead and zinc mine owned and operated by BHP Billiton. Through implementing Six Sigma Plus Cannington wanted to:have in-house capabilities to change and improve; tailor for the needs of each business unit and department; have æSharing of its KnowledgeÆ as a tool for improvement and have a competitive edge across Cannington û to be better than our competitors; learn from and leverage off the successes of improved safety and prior business improvement efforts; and ensure networking and sharing of information have common measurement systems across all assets. As with most business improvement programs û Six Sigma Plus was met with some degree of skepticism, especially given the amount of resources involved. After 18 months, much of this skepticism has been replaced with enthusiasm as peopleÆs understanding and acceptance of its fundamental concepts are being realised. The idea behind Six Sigma Plus is that it combines sound technical solutions with high acceptance by those who need to work with or implement the change. The future vision for Six Sigma Plus is that it become part of what we do at Cannington û just like safety and environment û so that Six Sigma tools and methodologies are used in our every day work.

Jan 1, 2002

The alluvial diamond deposit in the Kimberley Region of Western Australia which became to be known as the Bow River Diamond Mine was discovered in 1982 by joint venture partners Freeport of Australia Inc and Gem Exploration and Minerals Ltd. Mining commenced in 1987. This paper describes the exploration programs and results from discovery to commencement of mining and reviews the public reporting of this process in the light of 1992 Ore Reserves Code (JORC, 1992). This case study illustrates the difficulties involved in resource estimation of alluvial diamond deposits. The study also shows that current reporting standards were, to a large extent, adhered to a full ten years before the diamond reporting section to the Code was formulated.

Jan 1, 1996

The sudden. explosion of relatively inexpensive digital process control computers has accelerated interest in the possibilities of economic savings by their use. In particular the metalliferous industries have shown that they are willing and capable 6f grasping this new technology and putting it to good use. These industries have a number of problems which need special attention. In many cases the process is difficult to measure and a reaction is often controlled by measuring a secondary effect, computing its relationship to the reaction and then applying the necessary corrective action. This creates problems in building the process model, designing the computer to process interface and in the subsequent system development. Environmentally the metalliferous industries create conditions which severely test sophisticated electronic equipment. Care taken in locating and housing this equipment is a major factor in ensuring reliability in Operation.

Jan 1, 1977

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

The process of hydraulic transport through pipelines, world-wide well known for the trans- port of fine-grain solids is also being used to a greater extent in mining for the handling of 1rimarily coarse-grain solid - water mixtures r the removal of, for instance Coal and waste mixtures after coal winning rising hydraulic monitors, lings for backfilling underground and :her tailings and flotation waste to A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining P',search Company) in Essen-Kray, GFR, to ¦urther improve this technology. The unit was :fanned and built by Krupp Industrie- and +hibau of Duisburg in cooperation with i r

Jan 1, 1980

The rapid advance in the adaptation of scientific knowledge to the treatment of ores, resulting in improved chemical and metallurgical processes, has enormously increased the possibility of working lodes profitably, which a few years ago were passed over as unpayable. By the discovery of chlorination, and later of "Cyanidation," by the highly improved methods of concentration, and by the rapid advance in our knowledge of smelting (for which we are greatly indebted to Americanmetallurgists), and by the gradual replacement of scientifing principles and enlightened management, for rule-of-thumb methods formerly in vogue, many large low grade bodies have been opened, and are now paying dividends, which were,twenty years ago, looked upon as hopelessly unpayable. It has been more especially in these large low grade ore bodies, that modern methods have been benefical; for small lodes must be rich to pay at all, as they cannot be worked on the same gigantic scale, but even in these a percentage of metal is saved which formerly was absolutely lost.To make these large deposits remunerative it is, however necessary to try and find the point of greatest economic advantage, to handle the ore in vast quantities, to erect huge plats to treat it, to substitute automatic appliances for hand labour as far as possible, and to combine several processes supplementary to one another, so that ore which is not amenable to one process, shall be saved, by another; and by doing...

Jan 1, 1901

The Wainui Mill was conceived as a 60 - 90 t/d central mill to process gold ores of the Thames area of New Zealand from small mines in the district. The ores of the region exhibit various degrees of refractory response to conventional cyanidation leach due to the fineness of the gold, and association with pyrite. The alternative circuits involving cyanidation, flotation, and possible small-scale smelting are examined. The environmental impacts have been audited by the Commission for the Environment and were found to be acceptable.

Jan 1, 1986

By Getliffe RK

It is becoming more and more difficult to operate mineral and metal processes profitably, as operating costs rise, quality demands in-crease, international competition becomes more fierce and Government charges remain at their current levels. Profitability today depends upon efficient operations, which can only be achieved through precise and dependable con-trol of each process unit comprising thetotal plant.Modern process control systems utilise distributed architecture with microprocessor-based controllers, data acquisition devices and VDU operator stations. Honeywell intro-duced this control technology in 1975 with the "Total Distributed Control" System. Now, building on the proven performance and re-liability inherent in TDC hiway modules, Honeywell has extended the TDC system to inte-grate both management information and control by providing distributed processing modules on the new TDC 3000 Local Control Network (LCN).

Jan 1, 1985

The sequences in alteration and mineralisation from five copper-gold porphyry systems (Taysan and Didipio, Philippines; Horse-Ivaal and Wafi River, PNG; and Goonumbla, Australia) and one gold-copper skarn system (Browns Creek, Australia) are documented in this paper. Alteration and mineralisation in all these systems reflect a common evolution from crystallisation of melts emplaced at shallow crustal levels (zoned potassic -> propylitic alteration), followed by exsolution of volatile-rich fluids from these melts (porphyry quartz ¦K-feldspar/biotite veins and local high temperature advanced argillic alteration), to a progressive cooling of the intrusion which results in associated retrograde alteration. Copper-gold mineralisation in all cases is almost exclusively restricted to the cooler retrograde events. The recognition of the temporal and spatial zonations in alteration and mineralisation in gold-copper porphyry systems has significant relevance in the interpretation of geophysical signatures, overprinting alteration, vein sequences and structural controls, and can lead to more focused and potentially more cost-effective exploration.

Jan 1, 1999

By B Orchard

New Zealand SteelÆs Waikato North Head mine, situated at the mouth of the Waikato River, supplies approximately 1.2 million tonnes per annum of titanomagnetite concentrate to the Glenbrook steel mill. The mine draws its fresh water supply from the Waikato River, abstracting approximately 38 000 cubic metres per day. During the concentration process of the ironsand, slimes are liberated into the plant wastewater. The plant wastewater, storm water and groundwater from the mining operation is treated and passed through settling ponds. Around 118 400 cubic metres per day of water are drawn from the recycle settling ponds for use in the concentration plant. Typically a daily average of up to 15 100 cubic metres of the treated water is discharged back to the Waikato River. Since the early 1990s significant improvements have been made to the water treatment at Waikato North Head mine and regularly the mine discharge water quality is similar or better than background river water quality.

Jan 1, 2002

And it takes more than good organisation. You may read or heard this poignant reflection: We tried hard, but it seemed that every time we were beginning to form up in teams we would be reorganised. I was to learn later in life that we tend to meet any new situation by re-organising, and a wonderful method this is for creating the illusion of progress while producing confusion, inefficiency, and demoralisation This was written by the Roman Gaius Petronius in AD65. How much have things changed in nearly 2,000 years? What then does it take besides the fundamentals and good organisation to build a successful career in a successful organisation? I'm prepared to venture a list of what I'll'call Tips for Young Professionals. If you've got what it takes, and apply these, I think that you'll gain a great deal of satisfaction from your career, even if you don't reach the distant target each of you should have in mind now. So settle back in an advice-receiving mode, and please forgive me if I come across as a master of the bleedin' obvious, as Basil once accused his wife Sybil of being in the unforgettable Fawlty Towers.

Jan 1, 1990

A thermochemical model is developed to study the two-stage smelting reduction process for ironmaking without post-combustion. Steady-state multi-material and heat balance equations are solved simultaneously to study the effect of metallisation, slag basicity, coal rank and heat loss on consumption rates of coal, ore, flux and oxygen and production rate of slag to produce hot metal of a given composition, tapped at a given temperature. The model is applied to the commercial data for a COREX-plant producing a wide range of hot metal compositions, tapped at different temperatures. The computed rates of coal, slag, flux, ore and oxygen were found to be close to the reported ones, but an exact match could not be obtained. It is found that a four per cent change in metallisation brings changes the coal rate by five per cent, flux rate by six per cent, slag rate by eight per cent and oxygen rate by 13 per cent, while a ten per cent change in basicity changes the coal rate by ten per cent, flux rate by 13 per cent and oxygen rate by 22 per cent. Further, it is found that an increase in metallisation decreases the coal rate and export gas. At a given per cent metallisation, the coal rate and the export gas are lowest for anthracite compared to all other types of coal.

Jan 1, 1999