Search Documents

Much attention in controlling blast vibrations has been centred on the probability of causing damage to structures in the area adjacent to where blasting is carried out. In most cases these structures are residential properties and the effect of the vibrations on the occupiers has not been studied to any great extent. This paper looks at the sources of disturbance caused by blasting and their psychological effect. A comparison of ground vibration levels for compliance is examined within the framework of structural and human response.

Jan 1, 1998

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

By A G. Dempster, B McKeown, S Saydam, J Coulton

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

This paper presents a resume of the likely profitable mining areas in New Zealand. It covers the main 'minerals' û gold, coal, oil and gas, ironsands, silica sands, clays, lump silica, perlite, sulphur and limestone. The potential mining projects are depicted on a map of New Zealand together with the associated works involved in hydro-electric and geothermal power development requirement for industries such as aluminium, nickel ferro-silicon or silicon carbide production. The political need for mining development to relieve unemployment and reverse emigration is stressed. A case is made for exploration and development assistance by government in labour re-training, energy supply and transportation, if the tremendous losses through lack of use of human and industrial resources are to be rapidly reduced. These losses are currently estimated at $10 000 000 000 per year. The need for protection of the sanctity of contract and security of tenure of all mining operations is touched on briefly as is the need for a reasonably balanced view on conservation. However, as both of these are more properly covered in papers on the legal and environmental aspects of the mining climate, they are presented here only as they affect the economy of the mining operation. Finally, there is a brief comment on the mining climate in New Zealand relative to Australia and South Pacific mining operations.

Jan 1, 1990

By Hoppe AJ

Drilling and shooting techniques at Moura open-cut have evolved over a period of 16 years and are the result of hard earned experience combined with established practices and consul- tation with professional services. The wide range of overburden types encoun- ted in the field requires varying methods to achieve the best results at all times. Safe working conditions for the employees and protection of mining equipment is of para- mount importance and close liaison is maintain- ed with the Department of Mines Queensland to keep abreast with changing legislation. Drill patterns, charging profiles, types of explosives and ultimate results are des- cribed in detail along with a resume of equip- ment. Costs of drilling, labour and explosives are also analysed with a total of approximately 20c per cubic metre of shot ground. Future developments and improvements to facilities are also outlined.

Jan 1, 1978

The greater part of this paper comprises the material used in a lecture delivered to the South Queensland Branch of the Australasian Institute of Mining and Metallurgy in September, 1949. It contains little in the way of original matter, its main purpose being to call attention to the need for research into the properties of Queensland coals and to indicate some of the lines such investigations might profitably follow.Since the lecture was given the Powell Duffryn (1949) 1 report, which has made an excellent start along these lines, has been printed. This report is, however, only a beginning, though a big one, and there is ample room for many years of work along similar lines.The paper is based largely on the work of de Jersey (1946, 1949)2,3,4,5 and Jones and de Jersey (1947)6, but these workers in turn owe a debt to the work of many British and American investigators, too many to enumerate. The subject is a very large one-to deal with it fully would require not a paper but a book; all the author can hope to do is to discuss very briefly some of the main lines of investigation and indicate some of their applications.The reason for selecting Queensland coals in particular is the widespread ignorance of the extent of the coal resources of that State and the almost complete ignorance, to within the last year, of the modern industrial purposes to...

Jan 1, 1950

Ecological Fuel from High-Sulfur-Content Coal

Sep 13, 2010

By J Wei, X Lan, F Wang

This paper presents a quantitative assessment model for the assessment of environmental load in gold production, which is based on environmental ecology, Life Cycle Assessment (LCA) and artificial neural network. In LCA evaluation indexes include resource consumption, energy consumption, gas waste, liquid waste, solid waste and so on. Each item represents an aspect in gold production while their combination reflects the relationship between gold production and environment. In this paper an utility function of evolution index on environmental load is given by linear or non-linear transformation, which changes evaluation indexes with different dimension into an equivalent value in range of [-1, 1]. This paper also provides a new approach to make decision on the weight for quantitative assessment with the help of a three-layered artificial neural network. The proposed approach in this paper has been successfully used to a real synthetic assessment for the environmental load in gold production, which include seven kinds of different operational technologies in China. The applications prove that the new approach is successful and reliable. It provides a new tool for the assessment of environmental load of the gold production.

Jan 1, 2003

The first difficulty encount.ered in preparing this paper was to find a definition of the word "special" as applied to steel. The first thought is "obviously any grade not mild steel" but this is an over-simplification, because the term "mild steel" covers a series of carbon ranges, each found from experience to be especially suited to the production of a particular rolled section.Even if the Australian structural mild steels are excluded it is found that no part of the plant here is independent of special steel.The face-man on Iron Monarch makes his bench safe by barring down with a 0.6% carbon steel bar. He bores a hole into the ironstone with a 0.75-0.8% carbon steel drill, driven by a jackhammer which is built of a variety of special steels. After it is shot down, the stone is lifted by an electric shovel, very few of whose steel components fall into the general category of structural grades of mild steel.Further special steels are met with in the truck into which the stone is loaded, the hauling electric locomotive, and the rails on which these .run. Even the permanent way uses more than one grade, e.g., the crossings experiencing heavy service have their frogs built with austenitic manganese steel inserts.Special steels play their part in the overhead crane which tips these trucks, and in the crushers into which they discharge, and so they can be followed right through the production line, and they are still there at the seaward end of the ship loading boom at the head of the WhyalIa ore jetty.

Jan 1, 1951

A new test coke oven of 7 cu. ft. capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from theflues on either side of the charge.The method of charging permits close control of charge conditions such as bulk density and moisture content.These conditions, as well as coking conditions (e.g. flue temperatures and coking time) must be varied to simulate conditions in different batteries. The effects of several variables on coke quality are discussed.Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes. For 17 tests, the average ASTM stability and hardness indices for the test oven coke were 38· 5 per cent and 69·7 per cent, while those for the battery coke were 37· 4 per cent and 67·6 per cent.Observed relationships between coke yield and productivity, and volatile matter and charge moisture are given.The use of a test oven to classify test coals into prime-, medium-, poor-, and non-coking coals is discussed.This may be achieved by observing the effects of the test coal in blends with other coals. The results of a series of blending tests are presented.The dangers of attempting to predict coke quality from a single coal property are pointed out, since this can be done only for very restricted ranges of coals.A diagram is given showing the established trends in the effects of blending various types of Australian coals on coke strength.

Jan 1, 1970

Author Biography William Poole was born in Sydney, NSW in August 1868. He was educated at Sydney Grammar School. William spent two and a half years as a cadet in the Railway Construction Branch of the NSW Department of Public Works doing office and field work. He then undertook a civil engineering course at Sydney University. Following this he was employed for six years as assistant and resident engineer at the Water Conservation Branch, NSW and was in responsible charge of various field operations, surveys, river gaugings and works of constructions including a large timber weir and also a concrete weir on the Macquarie River, NSW. He then undertook a mining and metallurgical course at Sydney University and became a graduate (BE) with honours in civil engineering, mining engineering and metallurgy. He then spent four and a half years with BHP Co, one and a half years at Broken Hill in the mining and concentration works and three years at the smelting works in Port Pirie, SA, in the latter case he was metallurgist and night superintendent and during that time had responsibility and control at night of the blast furnaces and, during the last 15 months, of the whole of these large works. The author left the Port Pirie, SA works to assume the position of Director of the State School of Mines at Charters Towers and had responsible control of the establishment and also lectured in mining, surveying and structure. William Poole was honoured to hold membership in the following organisations: Assoc M Inst C E, L S of NSW, M Aus Inst M M, Assoc Inst M & M (London).

Jan 1, 2006

By D J. Robinson, L L. Kuhar

In-situ recovery (ISR) is accepted and applied across many geographies, and approximately 50% of the world’s uranium is currently extracted by using an ISR method (World Nuclear Association, 2014). The low environmental impact, the elimination of risk for mine workers and the fact that all of the lowest-cost producers of uranium use an ISR approach should raise interest from traditional miners (IAEA, 2014). However, the broader application of ISR to other commodities and mineral systems remains limited. A number of demonstration (experimental) copper projects have been undertaken (Sinclair and Thompson, 2015) with a few copper projects in Arizona being close to demonstration (Florence, 2018 and Gunnison, 2018). Evidence of very few economically operating ISR copper projects can be found (for example, the Russian, Uralgidromed OAO, built by the Russian Copper Company in 2005 and operated as an ISR facility from the Gumeshevskoye deposit (Russia Mining, 2018). A number of gold deposits, particularly paleochannel deposits, have also been considered for ISR, but, to the best of our knowledge, only limited demonstration and no commercial operations have been established, yet (Kuhar et al, 2018 and references therein).CITATION:Robinson, D J and Kuhar, L L, 2018. Extending mine life through application of an in situ recovery approach, in Proceedings Life-of-Mine 2018, pp 56–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By R W. Wilson, F H. von Glehn

With ever-increasing energy costs and the modern focus on system efficiencies, the practice of æventilation-on-demandÆ is gaining momentum. Several examples, ranging from paper studies to practical examples have been recorded and another recent case study is presented here to encourage the practice. In comparison, æcooling-on-demandÆ has received far less attention. This paper explores the possible merits of this practice by investigating the theoretical response of cool intake airways and the thermal interaction between the air and the rock, in order to gain a better understanding of the system behaviour and to quantify the possible savings. A case study is presented that demonstrates the improvements that can be achieved. Recent developments that allow live interaction between ventilation network models and on-line monitoring systems, have the potential for intelligent active control and alarming of ventilation and cooling networks. This will facilitate and maximise the benefits to be derived from ventilation and cooling-on-demand.

Jan 1, 2005

By I Treloar, T Elenbaas, E Isaaks

Critical reviews of grade control generally focus on blasthole sampling and the estimation of ore control block model (OCM) grades, with little or no attention given to dig-line design. For example, the estimation of block grades is deemed important as estimation errors lead to the misclassification of ore types and subsequent dollar loss. Recognition of the problem that the underestimation of block grades may be more or less costly than overestimation led to the application of loss functions to the classification of individual OCM blocks by ore type. The method is known as maximum profit selection (MPS). However, each OCM block may be misclassified a second time by dig-line design. Although each block may initially be assigned an optimum ore type by MPS, OCM blocks are seldom individually mineable by ore type. As a result, a common solution to this problem is the design of mineable polygons or dig lines loosely constrained by a minimum mining width. All material within a properly designed dig-line polygon can be mined and sent to a single destination such as the mill, stockpile or waste dump. These dig lines are often designed manually or by simple variations of computer-generated contour lines. They are generally suboptimal and result in additional misclassifications of ore types. This paper provides an algorithm for constrained optimum dig-line design where dig-line misclassifications are also evaluated through loss functions or MPS. Constrained optimum dig-line designs minimise the dollars lost by dig line misclassifications for a given minimum mining width constraint. A case study is provided illustrating constrained optimum dig-line design and subsequent benefits.CITATION:Isaaks, E, Treloar, I and Elenbaas, T, 2014. Optimum dig lines for open pit grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 425–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Healy T. W, Dixon D. R

The present study 'of pure ZnS and NiS and ZnS (marmatite) by detailed electrokinetic methods has shown that by careful control of experimental parameters much new' information on sulphide-water interfaces can be obtained. Time-dependent processes of alteration of sulphide surfaces are foHowed by electrokinetic methods and indicate that the isoelectric point of the surface depends on elemental sulphur coverage, oxidation product coverage, and the conditions which promote or minimize such reaotions in the presence and absence of activator.

Jan 1, 1977

By D A. Cuello, G B. Sharrock

The Prince Lyell orebody at Mount Lyell Mine has a rich mining history commencing with the open pit in 1935, which transitioned underground in 1972. Between 1972 and 2014 a total of 64 Mt was mined underground as the mine extended from 210 m to 1100 m below surface. As the depth increased, three separate transitions in the mining method occurred to meet the changing geotechnical conditions, ore grade, mining costs and metal prices. The first was open stoping with pillar recovery in 1972, followed by front caving and longitudinal sublevel caving (1995), and finally transverse sublevel caving (2004 to 2014). This paper provides an overview of key geotechnical and planning milestones relating to the evolution of the mining method including underground stability, gravity flow, cavability and subsidence. Key aspects of the mine design, geotechnical parameters and rock mass response are described and critiqued with reference to observational, numerical and empirical methods.CITATION:Sharrock, G B and Cuello, D A, 2016. Geotechnical milestones at Mount Lyell Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987