Search Documents

The Porgera gold mine has made significant progress with the successful installation of a JK FrothCam image analysis system. The system is used to measure and control froth velocity on the scavenger circuit which has brought significant economical and operational benefits. The froth velocity signal, determined by analysis of the camera, is transmitted to the PLC that manipulates flotation cell airflow rate and cell level controllers to maintain a target froth velocity of 130 mm per second. Following on from a three-week trial installation in June 2000, a permanent installation was commissioned on the scavenger Outokumpu (OK150) tank cells. Further work is in progress on the rougher Wemco cells. This paper describes the evaluation of FrothCam Technology and its subsequent installation.

Jan 1, 2003

By D L. Decker, G C. Miller, C Papelis

Arsenic, often associated with precious metals ore deposits, is a major contaminant released during large-scale gold mining. Because of the complex oxidation/reduction and sorption behaviour of As, prediction of the long-term mobility of As in pit lakes is uncertain. The behaviour of As in pit lakes is investigated in this paper by conducting a series of laboratory experiments where As is allowed to adsorb onto pit lakes sediments. Experiments were conducted over a range of pH with both As(III) and As(V) allowed to adsorb onto sediments collected from existing pit lakes found in the three main orebody types in Nevada, USA; porphyry copper, quartz-adularia gold, and Carlin Trend type gold deposits. Results from adsorption experiments show that As(V) and As(III) adsorption is strongly pH dependent with higher uptake at pH 5 and lower uptake at pH 9 for As(V) and higher uptake at pH 9 and lower uptake at pH 5 for As(III). This behaviour, as expected for oxyanions, has been described previously for agricultural soils, iron oxides, and Carlin Trend heap materials. Maximum adsorption of As(V) for the Carlin Trend type gold sediment was 3.0 g/kg at pH 5, 2.0 g/kg for the quartz-adularia sediment, and 0.9 g/kg for the copper porphyry sediment. Maximum adsorption of As(III) for Carlin Trend type gold sediment was 2.5 g/kg at pH 9, 2.2 g/kg for the quartz-adularia sediment, and 2.1 for the copper porphyry sediment. Adsorption isotherms are non-linear and show Freundlich isotherm behaviour. Variations in sorption between the different pit lake sediments under similar conditions can be explained by differences in the elemental composition of the sediment. Most rock forming elements from XRF analysis are similar in quantity except for Fe. The Fe content is highest in the Carlin Trend type gold deposit sediments and lowest in porphyry copper deposit sediments and is the third most abundant element in all three sediments. The Fe content of the sediments correlates well with the amount of As sorption seen in the laboratory experiments.

Jan 1, 2003

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

The uptake of nickel into the lattice of pyrrhotite, Fe1 _1J S was studied experimentally in the temperature range 200°C to 760°C. Nickel from both aqueous solutions and salt melts diffuses rapidly into the sulphidelattice with an accompanying release of iron into the solution or melt. The rate of uptake of nickel and its diffusion into the sulphide lattice were followed by optical microscopy and by analysis with an electron probe microanalyser. Some geological consequences of this phenomenon affecting the distribution of nickel in rocks associated with nickel-iron sulphide ores are discussed.

Jan 1, 1972

By H Haghighi

Haul roads are often permanent unsealed access roads used by heavy haul trucks to transfer minerals. These roads can deteriorate rapidly which results in potholes, deformations and dust. Downer EDI Works has successfully provided efficient solutions to the mining industry to maintain their haul roads. HaulPac as a solution package is a process in which a bituminous emulsion is used to create a stable and durable pavement. The emulsion penetrates the road and binds the particles together, creating a stable base. It also seals the surface and prevents water from penetrating the underneath layers. Bituminous emulsion can increase the strength of the pavement material and decrease the road surface degradation which results in dust suppression. However, the everincreasing price of commodities, the necessity of reducing carbon emissions and the increasing use of autonomous haul trucks have made it vital to invest in novel maintenance solutions that can meet the needs of the mining industry in a cost-effective manner. This paper outlines the benefits of bituminous emulsion in terms of productivity, safety and environment followed by Downer’s approach to evaluate the suitability and to optimise the amount of product. The potential for changing the colour of the treated surface is explored and an initiative that incorporates end-of-life tyres of haul trucks into the pavement is introduced. And finally, an innovative method using artificial intelligence to estimate dust emission is presented.

Sep 18, 2023

By Nikaido M, Kanda Y

A rotary type separator has been developed which separates particles on the basis of their shape. This separator was applied to a particle size range of about 50 - 120 ¦m, and to our present knowledge may be the smallest size range ever to be separated. A theory of the separation is given based on the difference of an adhesive force of the particles: the adhesive force between spherical particles and plate is more powerful than that of irregular shaped particles for the same particle size. These facts have been ascertained by the measurement of an adhesive force by a centrifugal method. US and Japanese patents have been obtained on this separator, which consists of a borosilicate glass cylinder of 150 mm outside diameter, 120 mm in width, and an AC electromagnet. The samples used in this study were mixtures of spherical glass particles and non-spherical shaped glass particles. The results are summarised as follows. In the case of mixtures of spherical particles and irregular shaped particles in the weight ratio of 1:1, the spherical content of the spherical product became 70 per cent - 75 per cent, and in the case of 3:1, the content became 87 per cent - 90 per cent, as the result of one separating operation. However, for a mixture of somewhat rounded particles and irregular shaped particles of weight ratio 1:1, the rounded content varied between 58 per cent - 73 per cent. The feed rate of the particles mixtures was about 0.3 g/min. Newton's Efficiency was 20 per cent - 60 per cent. The separator may find application in shape separation of ceramic powder, metal powder or industrial diamond powder.

Jan 1, 1993

THOSE who dabble in mining are no exception to the general rule that persons who know a little of a subject are apt to think that they know all about it. Some colour may be lent to the belief that anyone may succeed in mining when we hear stories ofsuccessful diggers and others who have accidentally dropped on to something good through no foresight on their part; but we seldom hear the contra account of the far larger number who fail. Those who go more thoroughly into the subject, and take up mining as a profession, know very well that it is not one that can be carried out successfully by rule of thumb, but when they point this out to the public they are credited with trying to make it a closed profession; and outsiders are for ever trying to find out the "trade secrets," at the same time spurning the main one, which is hard study, experience, and the ability to apply their knowledge. The average mining man is not rich. When he amasses a fortune it is generally through speculation rather than professional work, thought no doubt his technical knowledge may have assisted...

Jan 1, 1910

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

By G H. Clark

Batu Hijau is a porphyry copper-gold deposit located onSumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54 000 m of drilling in 105 diamond drill holes over a surface area of 1.2 km2 and to a depth of 1000 m below surface (412 m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55 g/t Au (variable cut-off) from an open pit in the higher grade portion of the resource.   The deposit is associated with a calc-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200 m diameter at surface to 500 m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbledykes or postmineralisation intrusive rocks.   Hydrothermal alteration of Old Tonalite and adjacent rocks is centred on the Old Tonalite and is zoned from a core of pervasive potassic alteration grading to an outer propylitic halo. At depth a propylitic assemblage is developed in the low grade core in the Old Tonalite. Phyllic alteration, late stage and mainly fracture controlled, overprints both potassic and inner propylytic zones. Intermediate argillic alteration overprinting is widespread, particularly on the eastern side of the hydrothermal system, where advanced argillic alteration overlies argillic alteration.   Ore grade mineralisation is cylindrical in shape, up to 800 m in diameter, and is centred on the Old Tonalite. A high grade shell (>0.75% Cu) forms an upward tapering cone in and around the Old Tonalite and reaches the surface in the centre of the deposit. Lower in the shell >l g/t Au and >2 g/t Ag accompany >1% Cu. Below 75 m above sea level mineralisation in the Old Tonalite rapidly decreases as a weakly mineralised core develops, but the limb continues to contain mineralisation to at least 412 m below sea level. Fracture and vein-controlled chalcopyrite and bornite are the dominant hypogene copper minerals and are the hosts for most of the gold mineralisation. Gold occurs free and in the lattice of the copper sulphides, and has been observed in quartz.   Weathering, especially where argillic alteration is developed, has produced a strongly leached cap, up to 147 m thick, below which is an irregular copper enriched supergene zone. Where leaching is not developed, such as over the centre of the deposit, an irregular oxide zone and a weakly developed supergene zone may be present.

Jan 1, 1995

By P Bonniwell

As a part of the Newcrest, Telfer Expansion Project, a consortium of Australian, Canadian and South African Mining Contractors in joint venture have been contracted to develop the hoisting shaft. The parties namely; Byrnecut Mining Pty Ltd, Murray and Roberts RUC and Thyssen Mining Construction of Canada Ltd have combined their individual expertise to excavate the shaft. There is a particular emphasis on the use of proven shaft sinking techniques from North America and in particular integrating electric hydraulic drilling equipment and personnel from the Canadian Mining industry. The Telfer hoist shaft when completed will have a finished diameter of 7.1 metres and extend to a depth of 1170 metres below the collar. The shaft will be fully concrete lined and will later be equipped for hoisting ore from the Telfer deeps at a rate of five million tonnes per annum. The shaft when completed will be the largest shaft ever completed in Australia on a volumetric basis. This paper will examine the technical aspects of the shaft sink, as well as exploring the integration of personnel and equipment from the frozen prairies of Saskatchewan, Canada into an operation in the Great Sandy Desert of Western Australia. What are the spin-off benefits for the development of other shafts within Australia?

Jan 1, 2005

Study on the Recovery of Zinc Minerals from the Tailing of a Lead and Zinc Mineral Processing Plant

Sep 13, 2010

By I Warren, M P. Simpson

Adularia-sericite epithermal ore deposits have well-documented alteration mineral zonation patterns with distinctive geochemical signatures. Proper use of whole-rock geochemistry can provide useful vectors for exploration and can enhance efforts to characterise and quantify the mineralogy and intensity of hydrothermal alteration.   Analyses of Au and Ag provide the most direct vectors to orebodies, and pathfinder elements such as As, Sb, Hg, Zn, Pb and Se are similarly zoned around at least some orebodies. However, the minerals that contain these elements occur almost exclusively in veins, and therefore identifying geochemical vectors related to wallrock alteration that is zoned outward from orebodies is crucial for effective exploration.   Distal alteration zones contain quartz-illite-chlorite-carbonate-pyrite, whereas samples proximal to veins contain quartz-adularia-pyrite, with lesser though variable illite-chlorite-carbonate. Therefore, adularia-sericite epithermal ore deposits show K alteration in their cores. The resulting K-metasomatism can be evaluated in several ways. Areas that have been most intensely altered are commonly characterised by highest K contents, but these results can be complicated by variations in rock type across the prospective area. Potassium mass balance results provide a robust and rigorous assessment of K-metasomatism, however, knowledge about the composition of fresh rocks and correct identification of fresh precursor compositions of altered rocks are required. Three alteration indices provide effective evaluation of K-metasomatism: 1.   the K number, which is the ratio K/(2Ca+K+Na) (molar); 2.   Barrie values [(K2O * 100) / Sr]; and 3.   the Rb/Sr ratio. In most places these provide similar vectors, although K numbers can be complicated by the appearance of hydrothermal calcite and/or albite.   Plots of K/Al vs (2 Ca + K + Na)/Al (molar) allow estimation of the intensity of K-metasomatism and its mineralogical products, thereby complementing traditional XRD and petrographic studies of alteration minerals.

Jan 1, 2005

Laboratory testwork was carried out on an overall orebody composite, of 2.9 per cent Cu and 4.2 per cent Zn, prepared from drill core taken from the Currawong fine-grained, copper-zinc massive sulphide deposit near Benambra in Victoria. While 90 per cent of the copper was readily recovered in a concentrate of 20 per cent Cu, after grinding to 95 per cent passing 38 microns, zinc responded poorly to conventional flowsheet/reagent regimes. Experience elsewhere with the use of reverse cleaning, to separate pyrite from sphalerite, led to a series of tests in which better (but still modest)metallurgical results were obtained. The best result was a zinc recovery of 55 per cent in a concentrate of 50.5 per cent Zn. The major loss of zinc occurred in the reverse cleaning stage where the unit recovery of zinc was similar to pilot plant results achieved at Mount Isa Mines on similar feedstock. Diagnostic mineralogy suggested that an overall zinc recovery of 70 per cent was probably the practical upper limit, at a 50 per cent Zn grade.

Jan 1, 1999

By K Shannon, A Shaw

The Hilton and George Fisher deposits occur 22 and 24 km north of Mount Isa, NW Qld, Australia respectively. Both deposits occur as deformed Proterozoic, sediment hosted, stratiform orebodies hosting Pb-Zn-Ag (Hilton) and Zn-Pb-Ag (George Fisher) mineralisation. The two deposits are separated by approximately 2 km of strongly faulted barren shales, mudstones and siltstones along strike. Despite this, correlations between the Hilton and George Fisher deposits have previously been assumed on the basis of textural, lithological and geochemical similarities, but previously lacked specific details to prove exact stratigraphic matches.Feasibility drilling allowed broad correlations based on the position of siltstone pillars separating individual orebodies. However the position of continuous potassium-rich, siliceous and cross-fractured tuffaceous marker beds (TMBs) often used as stratigraphic markers within the Hilton Mine were initially unrecognised within the George Fisher stratigraphy where they are erratically silicified and often not cross-fractured resulting in correlations being difficult to prove. As a more detailed knowledge of TMB locations at George Fisher was gained it was possible to look for corresponding TMBs within the Hilton orebodies. Recent underground stope definition drilling at the two locations enabled specific TMBs, stratigraphic units and even individual sedimentary beds to be matched between the two locations, despite the large separation between mines.The correlation between the two deposits has implications for future exploration drilling north of George Fisher. If a specific stratigraphic horizon can be determined within one hole, positioning of further drillholes can be more accurately planned. The significance of having stratigraphic matches between Hilton and George Fisher also has implications for correlations with other Isa Valley deposits. Convincing preliminary TM and stratigraphic correlations have already been made between George Fisher and the Isa Lead Mine 24 km to the south.

Jan 1, 2002

By J Zhang, R Dimitrakopoulos

A two-stage stochastic mixed integer non-linear program is formulated for a mining complex to optimise strategic and tactical plans. The objective is to find the near optimal decisions for a mineral supply chain in the context with uncertainties in both ore supply and the commodity market (price and demand). The endogenous spot price in the commodity market and long-term sales contracts are considered in the formulation of the mining complex’s optimisation model and an ad hoc heuristic is developed to deal with the throughput – and head-grade-dependent recovery rate in processing plants. Numerical results indicate that the proposed heuristic is effective and efficient in numerical tests. Based on the proposed model and heuristic, a long-term contract design strategy is proposed for making decisions on the contract price and strategic investments. A shadow price based method is also proposed to evaluate the existing mining schedule.CITATION:Zhang, J and Dimitrakopoulos, R, 2014. Optimising a mineral supply chain under uncertainty with long-term sales contracts, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Pan, B-J Shi, X-B Li

The granulation behavior of specularite fines which possess poor ballability was studied with limonite fines as a function of nuclei particles and adhering fines. The results show that the permeability of granules deteriorated as the ratio of specularite fines increased in the mixture, and the optimal granulation moisture content also decreased. The granulation kinetics results demonstrate that the adhering load of specularite fines increases rapidly within three minutes and then levels off. With increasing specularite fines ratio, the adhering speed is accelerated but the granulation duration needs to be longer to reach adhering balance. The microstructure of granule quasi-particles indicates that the fine limonite particles act as binders to bond together the specularite particles which are dispersed in the adhering layers. This can improve the adhering strength of the granules. Hence, the granulation behaviour of specularite fines can be improved by blending them with fine limonite ores which have high adhering capabilities.CITATION:Zhu, D-Q, Li, X-B, Pan, J and Shi, B-J, 2015. Granulation behaviour of specularite fines in ferrous sinter mixtures, in Proceedings Iron Ore 2015, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Hare S. M, Lumsdaine I, O&apos

Converter slag assaying 3.7 per cent Cu is produced by Mount Isa copper smelter at a rate of up to 180 000 tonnes per annum.Priority is given to the processing of ore, however concentrator capacity periodically exceeds that of the mine and the opportunity is taken to treat converter slag. It is processed in batch campaigns, typically through the Copper Concentrator, but the Hilton Concentrator has also been used. Slag and ore are kept as separate as possible, since each has an adverse effect on the flotation performance of the other.

Jan 1, 1993

By Reilly L, Worner H. K

The EnvIRONment process has been developed to treat steel works dust and organic wastes simultaneously. A pelletised feed is fed into a special DC electric furnace, the pellets becoming immersed in a molten slag above a carbon saturated bath. The iron oxide in the pellets is reduced and carburised whilst the organics are broken down to carbon monoxide, carbon dioxide, hydrogen and water vapour. Volatile metals are vapourised and collected in the baghouse. Over two years of trials in a 100 kg DC electric are furnace has brought the process to the stage where it is ready for commercialisation.

Jan 1, 1995

The Mining Act (1992) and the Petroleum Act (1980) provide for the Government of Papua New Guinea (PNG) to take up equity holdings in mining and petroleum projects. The price the Government pays for its share is based on the historical cost of exploration and development on the project to the date of government equity acquisition. The equity level to be acquired is not fixed and ranges up to 30o for mining and up to 22.5s for petroleum at the discretion of the Government of the time.The objective of this paper is to examine the pros and cons of State equity holdings in PNG from the point of view of both the State and the developer. Using an economic model of the PNG mining taxation system an assessment is made of the effective return on investment received by the State from such equity holdings. The results are compared with government revenues from other taxation measures.

Jan 1, 1994