Search Documents

The district specially referred to in this paper comprises the very gently sloping country extending from the western shores of Port Phillip from the mouth of the Yarra to Footscray along the Bacchus Marsh railway to near that town thence in a southerly direction to the Little River, and along that river to the coast, 1 as may be seen on the accompanying map. Almost the whole of this area is covered by volcanic rocks, consisting of pumerous sheets of basalt, which have been poured out of various volcanic hills in the districts, such as Mts. Atkinson and Cotteril, near Melton; Mt. Maryand Bald Hill, 12 and 16 miles respectively N.W. of Werribee; and vents in different parts of the parishes of Tarneit, Mouyong, Mooradoranook, Pyweitjorrk, and Derrimut. These volcanoes were in an active state of eruption during a late period of the earth's historyprobably the late Pliocenll, or still younger Pleistocene.Occupying a narrow strip of country, for most of the distance along the coast from Williamstown to past the mouth of the Little River, there occur deposits of still younger age, belonging to the Recent period. These lie on the basalt, and extend for distances varying from a few chains to more than a mile back from the beach. They comprise superficial deposits of blown sand, and raised beaches, composed of marine sands...

Jan 1, 1902

The Mineralogical Researches of Gold Ores and Technological Products at Operating Factory in Olympiada Mine (Russia)

Sep 13, 2010

By Horiszt G

his report is going to point to that the effect of the mining dewatering on the area of Transdanubian Mountain Range has reached a phase when the cost of dewatering and providing damages can seriously jeopardize a profitable mining operation. Up to 60s the interest of mining had been dominant only, but since the begining of 80s the conceptions of industrial development and the value of enviroment protection have been changed. The natural karstwater balance of the TMR can be presented (Figure Land 2.) and the present situation of it points to that the descharge has exceeded the reacharge in 50 %. During the past 10 years the decreasing of the stored karstic water resourches was 1.1 km . The decreasing of the spring yields reached 80-82 % of the natural ones. (Figure 3-4.). Conservation of the present discharge may lead up to the totaly drain of the karstwater regime. A computer aid control system had been to develop by the bauxite mining and using of it the yield of dewatering decreased and a moderate rising of the water table has started since 1986. A recunstruction was made at the biggest thermal-medicinal lake its springs have had their source in 40 meter depth inside a spring cave at the bottom of the lake. Earlier the spring yield decreased due to the dewatering activity of mines. As a result of using of the CAC system and the providing works at the thermal sprino,the karstwater balance has got in the state of equilibrum, the first cost was decreased and spring yield was increased and the enviromental limits were adverted from the way of mining.

Jan 1, 1988

An examination has been made of the rate and extent of removal of carbon from scrap metal charges when the melt is exposed to atmospheres which are reducing or oxidising with respect to FeO at unit activity. The mechanisms of decarburisation of molten Fe-C-S- P-Mn-Si alloys with H2/CO/H20/C02 gas mixtures with controlled compositions at high or low concentrations of carbon in the melt in the presence and in the absence of sponge iron, in both slag free melts and in the presence of various slag forming additives are discussed. A significant quantity of carbon can be removed from the metal during the melting stage and under optimum conditions, a high percentage of metal recovery and low carbon can be obtained after exposure of melt to the above gas mixture with controlled compositions. The presence of ferrous oxide provided by poorly reduced ore in the charge and the use of controlled atmospheres facilitated the removal of carbon to very low level during the melting period.

Jan 1, 1984

The advancements achieved in rapid tunnelling in the 60's and 70's have been notable. It is unfortunate that shaft sinking has not enjoyed equivalent advances and there are many good reasons why this is so. Technical and commercial considerations have held back development and continue to do so despite the increasing urgency in the search for minerals and energy. By the careful selection of an appropri- ate project and the application of specialist engineering the Bdard took advantage of a unique opportunity to apply a mechanised shaft borer in field conditions.

Jan 1, 1981

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By Leigh G, Gottleb G, Wilkie G

The estimation of particle liberation is important in the study of mineral concentration. With simple systems, where the densities of the components are low, the liberation can be studied directly by density fractionation. For most practical systems, and particularly for the dense, complex sulphides, the only method known is by measurement in polished section. There are two major difficulties with such measurements. Firstly, the measurements themselves are difficult and considerable care is needed before reproducible results can be achieved. Secondly, a well known stereological problem arises which gives the estimates an inherent bias. The paper discusses both aspects of the problem. The practical features of measurement are treated in detail and a method described which has been developed and proven to give reproducible estimates of the liberation in the section. This discussion relates to automated measurements by QEM*SEM and presents a way of estimating the confidence limits within which measurements lie. Comparisons are shown between measurements made by the traditional manual optical technique and automated equipment. Stereological reconstruction is also discussed briefly. Several methods have been presented in the literature but all are complex and none is yet widely accepted. Area measurements are less biased than linear estimates so a practical approach is to use area measurements in uncorrected form. The topic is still being actively researched so it is expected that one method will soon emerge as the standard technique.

Jan 1, 1993

Life inside the mining family was regulated by the mine. The whistle shrieked the change of shift to the Cornish, Welsh and German miners digging the alien soil for copper at Burra in the 1840s and the deep quartz gold mines at Bendigo in the 1880s.During the golden years of alluvial mining in the 1850s, and later out on the frontier fields of Kalgoorlie and Jarrahdale in Western Australia, the lure of the mine dominated family life. How could it do anything else? The canvas tent, bark hut or weatherboard cottage in which the mining family lived close by the mine facilitated prompt access. The working man of the family attended to the demands of the mine first, and those of his family afterward. Who then organized and nurtured the mining family? The role of the mining wife was multi-fold. She played the traditional roles of home-maker and comforter, raising her children, tending her house and vegetable garden and supporting those friends and acquaintances who had lost children to disease, or menfolk to the mine. Epidemics of measles, the whooping cough or influenza carried away children in infancy or at too young an age. The death of a husband through accident or disease (pthisis was a likely killer) forced upon the mining wife another role, that of provider. When Elizabeth Vigus' husband died in a Bendigo mine accident in March 1880 Elizabeth set up a grocery business to support her young children.' But in other cases the mining wife supplemented the family earnings by part time work, not in the mines for the Mines Act legislation of 1842 forbade the working of women underground, but in auxilfiary occupations which were in demand.2 Ann Mitchell, a herbalist ,found plenty of work in the goldfield towns of Daylesford and Maldon in the 1860s and 1870s.3 So too did Susan Rule and her daughter Catherine who conducted a sewing and millinery establishment in Beechworth in the 1870s.4 The making of the family's clothes was another task of the mining wife and mother.Until the wonderful invention of the sewing machine, this was a tedious and time-consuming task. James Slater Edmonson bought his wife a Wertheim for the sum of 12 pounds in June 1886, just before leaving her and his chil- dren in the Adelaide suburb of Goodwood whilst he went alone to the goldfields of the West. In October of that year he wrote to Louise telling her how he missed the childrens' wondering "whether Slater wore my old shirt now. I always think of him as he sat on my knee at breakfast in that old shirt; and how pleasant it would be if I could rock both of them and sing as I used to do".5

Jan 1, 1988

By Dunkin H. H

Flotation tests in a laboratory flotation cell at pH 8-8.5 and other sui}plementary tests were carried out on sphalerite-quartz and sphalerite-pyrite-'quartz mixtures. Depression of sphalerite resulted vvhen the addition of copper sulphate exceeded an optimum value. Evidence that this depression was due to collector deficiency because of reaction between copper sulphate and collector is presented. It was not found possible to devise a direct analytical method suitable for .plant control of reagent addition. A possible means of control using potassium cyanide and a higher pH is discussed.INTRODUCTIONAt the Rosebery mill of Electrolytic Zinc Co. of Australasia Ltd., recovery 'of sphalerite in the zinc concentrate occasionally drops unexpectedly. Experiment in the mill and mill laboratory has suggested that one of the factors causing this may be the addition of more than an optimum amount of copper sulphate. On such occasions, an increase in the collector addition improves zinc recovery in the zinc concentrate, but only at the expense of sphalerite-pyrite selectivity.To examine the phenomenon more thoroughly, and if possible to find some means of determining the optimum addition of cepper sulphate and controlling the actual addition at this optimum, one of the authors (W. J. T.) was employed by the Electrolytic Zinc Co. of Australasia' to carry out investigations in the Mining Department, University of Melbourne, under the joint direction of R. B...

Jan 1, 1954

By Woodhouse M, Andrews D, Drew G

The nickel deposits within the Honeymoon Well project area (26¦ 40'S, 120¦ 25'E), located 45 km south of Wiluna, occur in the northern part of the Agnew-Wiluna belt (Figure 1; Hill et at, 1990). The project area is covered by up to 50 m of transported material which greatly hampers both exploration and an understanding of the bedrock geology. Since 1990 intensive exploration has increased the resource from 10 Mt at one per cent Ni to 134 Mt at 0.76 per cent Ni in five deposits (0.4 per cent Ni cut-off, resources above 300 m depth, December 1994). This includes a massive sulphide resource of 2.5 Mt at 3.4 per cent Ni.

Jan 1, 1996

Since 1958 there have been 16 major coal mine explosions in the U.S. claiming 323 lives. Whilst the exact cause of a number of these incidents has not been determined, the majority has involved gas ignitions in one way or another. In addition there have been fatal gas explosions in salt mines and vapor explosions in oil mines. Furthermore, many of the oil shale mines in the U.S. have proven to be gassy giving cause for concern. Compounding these problems is the fact that frictional ignition of methane in coal mines has dramatically increased over the past several years; over 100 such ignitions were reported in 1979. While, no fatalities have been attributed to frictional ignition in the U.S. since early 1978, a recent mine explosion in Nova Scotia which resulted in 11 fatalities was attributed to a frictional face ignition. Research being conducted at the Bureau of Mines is aimed at the prevention and suppression of gas explosions. Emphasis is placed on new coal cutter bits for reducing ignition frequency, machine-mounted water sprays for preventing frictional face ignitions and automatic devices for quenching incipient ignitions and fully developed gas explosions.

Jan 1, 1981

A Novel Diagnosis and Evaluation Procedure for Flotation Plants

Sep 13, 2010

Flotation Circuit Optimisation - Towards More Sustainable Practice

Sep 13, 2010

By W Blair, J Bosman

The measurement of ferrosilicon rheology and characterisation of the parameters that have a direct influence on medium rheology provide the basis for evaluating, comparing and selecting an appropriate size and shape of medium to maximise separation efficiency in a dense medium application. The role of medium viscosity on particle separation in both static and dynamic separators is illustrated using relevant theory. The primary measurements of rheology are medium viscosity and stability. These in turn are determined by particle size, particle density and particle shape which in turn can be quantified. Additional characterisation parameters are also discussed. Different areas of application where ferrosilicon characterisation can be used are also discussed.CITATION:Bosman, J and Blair, W, 2017. The practical characterisation of ferrosilicon for dense medium applications, in Proceedings Iron Ore 2017, pp 135–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The pyrite-sphalerite-galena and barite orebodies at the Rosebery mine are concordant with the shale host rock and have been deformed into one system of folds with an associated axial plane cleavage. The folds are tight and overturned with east-dipping axial planes. Folds in the sulphide ore are commonly disharmonic, particularly between adjacent bands of different composition.Concentric style folds occur in the competent bands, e.g. pyrite-rich bands. Similar style folds are predominant in the less competent sphalerite-galena-rich bands and also in the shale of the host rock. The trends and plunges of the fold hinge-lines are variable but axial planes are of reasonably constant orientation throughout the mine area. The folds in the orebodies are of limited axial extent, approximating to conical folds, and are arranged in en echelon patterns. The fold system was possibly formed in one period of folding by heterogeneous strain that may have been caused by the presence of a mass of tectonically mobile sulphide ore. Lineations parallel to the ore/host rock contacts appear to reflect movement between the ore and the host rock during folding.

Jan 1, 1972

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

In this paper is given a description of the flotation plant recently erected by Broken Hill South Limited at the South Mine, Broken Hill, N.S.W. It has been built on the site of the old flotation plant, which was described in a previous paper published by the author. The present paper is supplementary to the former paper in that it replaced the following sections thereof, namely, those from end of the second paragraph, page 269, to the end of the first paragraph page 282, and from the end of the second paragraph, page 284, to the end of the third paragraph, page 302.The roll crushing, fine grinding, gravity concentration, filtration, disposal of products and sampling in the new plant are the same as described in the above mentioned paper.The reconstruction of the flotation section, described herein, completes the reconstruction and modernisation of the treatment plant which was begun in 1928. A description of these earlier alterations has already been published in the Proceedings of this Institute.

Jan 1, 1935

All previous attempts to cut rock in boring by means of revolving steel cutters have failed, chiefly in consequence of the mis-shapen teeth grinding the rock and themselves simultaneously, until, after a very few revolutions, the points of the cutters were so worn that it was impossible to force them into the strata. The diamond drilling plant being cumbrous, complicated, and costly, and seeing that fully 70 per cent of the boring generally needed is in what is known as the" milder strata," it will be readily understood that much of the work done will not pay a dividend on the outlay, so great is the cost of removal, the wear and tear of the machinery, and the loss of diamonds. The Calyx Drill, however, invented by Mr. F. Harley Davis, has been constructed so as to overcome these difficulties, and will penetrate quickly and .at a low cost this 70 per cent. of the milder strata. The Drill has taken ten years' hard work and thought to bring it to its present state of perfection, and it will now drill with steel cutters the 70 per cent of the work performed by the diamond drills at a greater speed and at about one third the cost of the latter.The utility of the diamond drill for certain work is undeniable, but it cannot by any means be described as a machine of general popular usefulness that is to say, it is quite beyond the reach of the great masses of mankind.

Mine dewatering has long been a problem with mines and some of the shallowest mines have the biggest problems. Machinery was developed by the ancients for raising water by rope buckets with treadmills or by horse whim. From the 1700's on into the early part of this century, massive cornish pumps or equivalent were the vogue powered by steam. One Australian mine pumping system was claimed to be the largest in the world just after the turn of the century. It was installed at Beaconsfield in Tasmania and the mine, like so many other mines of the period, were beaten by problems and cost associated with mine dewatering. The owners of that mine are looking at the feasibility of dewatering using surface drilled wells. Much simpler and smaller pumps are the order now and it is feasible to use boreholes instead of shafts to contain the pumps or else to use the holes to convey discharge waters to the surface from pumps located in drives or stopes.

Jan 1, 1988

By R M. Briggs

Kapowai Caldera Complex (KCC), located 10 km west of Tairua (eastern Coromandel Peninsula), is a late Miocene composite collapse caldera, formed during eruption of several small and large volume andesitic rhyolitic ignimbrites. Numerous epithermal Au-Ag mineral deposits and associated alteration zones at the KCC are related to caldera (rhyolite lava domes, intracaldera faults) or regional structures (faults). The main epithermal deposit exposed in the central KCC is associated with an E-W striking structural boundary fault that cuts the Welcome Jack rhyolite dome. Propylitic (calcite - chlorite) and sericitic (quartz - sericite) alteration haloes surround this deposit. Sporadic zones of sericitic alteration are also exposed within and on the margins of the Bulls Run rhyolite dome complex. Epithermal systems post-dated emplacement of these rhyolite domes, but were controlled by them. Propylitic alteration of ignimbrite in the floor of the Kapowai and Kauaeranga valleys is related to the major NE-trending Kapowai Fault which extends SW to south of Thames. Alteration along this fault pre-dates alteration associated with the rhyolite lava domes. Numerous sericitic and propylitic altered welded ignimbrite, rhyolite and andesite lava lithic fragments have been sampled from intracaldera ignimbrites, and although no direct source is known, they infer the presence of buried epithermal systems. Repeated epithermal activity at the KCC is inferred by the exposed epithermal deposits/alteration zones and the older buried geothermal systems. Silicic caldera volcanoes are considered to be critical volcanic environments for epithermal Au-Ag mineralisation in Coromandel, but are highly variable and need detailed stratigraphic, structural, petrologic, and geophysical studies to characterise them.

Jan 1, 1999