Search Documents

By Tronson K

Improvements in technology do not necessarily lead to higher profits: the benefit of lower costs can be captured by coal buyers, governments and workforce rather than by the colliery operators. The economic impact of longwall mining in Australia has been critically assessed to provide lessons for the future. For a variety of reasons, companies investing in longwall equipment in the past five years have generally not achieved an adequate return on the funds invested. The effect of technological innovation must be examined in the light of competitive forces operating in the market. Projections of cost reduction trends in the coal industry have been applied to a world cost model to provide a picture of the coal industry in the year 2000.

Jan 1, 1988

By Boyd G

Deep mining in the Collie Basin has suffered with high levels of water flow and sediment in-rushes throughout its 90 year history. Current day experience in working conventional bord and pillar by mainly mechanised means is that advance to the dip is impeded at about the 150m depth of cover by excessive water flow and pressure bursts. Extensive analysis of exploration borehole data and reconstruction of depositional environments helped define important hydrogeological characteristics of roof and floor aquifers, aquitards and aquicludes. Hydraulic parameters were estimated with some accuracy using indirect methods, and later confirmed by pump testing. Groundwater flow modelling showed that mine scheduling would have to be a balance between down dip and lateral development if aquifer pressure heads were to be decreased to suitable levels. Since pressure reduction in aquifers immediately above and below the mine opening was. identified as the key aim in groundwater control, a series of trial in-pit dewatering holes were installed, and demonstrated pressure heads could be reduced at rates compatible with a mine extraction sequence which, in turn, controlled the rate of down dip mine advance. A case history of the successful application of in-pit dewatering systems within difficult hydrological conditions for mining is described, with emphasis on the close collaboration required between hydrologists, mine planners and operations personnel.

Jan 1, 1988

The Golden Valley Volcanic Centre has been recently interpreted as being a combination diatreme breccia pipe and rhyo-dacite flow dome complex of Permo-Carboniferous age that intrudes basement granitoids and sediments of Ordovician-Devonian age. Exceptionally good exposure at the Centre has enabled the relationships between different lithologies to be determined. This, along with petrological studies, has led to a detailed understanding of the geological environment in which the complex formed. Gold, silver and base metal mineralisation have been recently shown to be associated with the Marginal Breccia at the perimeter of the diatreme. Comparisons have been made between the geology and mineralisation in this system and several similar diatremes which also contain gold-base metal sulphide mineralisation.

Jan 1, 1990

By Tominaga Y

Mine ventilation control is one of the most important techniques to suppress the disastrous region within a limited area, to have enough time of emergencies (ignitions, fires and so on) for underground workers. The purpose of this paper is to introduce the simultaneous controlling of mine ventilation by using, micro computer connected to various kinds of sensors. In this study, basic of mine ventilation and graph theory are used for making computer programs when the characteristic curves of fans and temperature distribution in an underground roadway network are given.

Jan 1, 1981

Utah's Blackwater mine began operations in 1967. The four CQCA mines controlled by Utah followed over the period 1971 to 1979. Project feasibility studies for all these were based on open cut mining to overburden depths of 60 metres, with typical project lives of 12 to 16 years, depending on reserves Further studies, initiated after the mines had started, showed that continuation of open cut mining beyond the 60 metre highwall was viable. In 1973, the Deep Stripping Project (DSP) was launched to define the scope for stripping deeper, to determine what the additional equipment needs might be, and to pu forward proposals for a full scale trial system. The project commenced at grass roots with a literature survey, proceeded through a sequence of equipment evaluation, specification, design and manufacture to the commissioning of the Goonyella BWE system. Studies are continuing to assess the future deep stripping requirements for all Utah's Bowen Basin mines.

Jan 1, 1983

By Azizan A

The paper presents the results of chlorination of beneficiated rutile and struverite (a tantalum-niobium bearing, rutile type mineral in alluvial tin deposits) by carbon tetrachloride in the range 623¦K to 773¦K. The chlorination of rutile could reach near completion at 773¦K in about an hour. The process was found to follow a modified pore-blocking law, with the basic reaction constant K varying inversely with the particle size, so that the basic process may be a reaction under interface control (chemical control) as modified by the pore blocking effect. The pore blocking factors for the various experimental conditions were evaluated and the predicted curves showed good agreement with the experimental data. In the case of Struverite, a similar kinetic behaviour was observed but the chlorination process was relatively slower than that in rutile. It was also observed that in struverite, niobium got chlorinated faster, followed by tantalum and titanium, indicating a good possibility of separation by chlorination using carbon tetrachloride.

Jan 1, 1996

Mining companies around the world devote considerable effort to production reconciliation and metallurgical accounting. However, although sampling, weighing and analysis methods used to obtain the raw data for metal balancing continue to improve, they are still areas that are sadly neglected. Using the latest metallurgical accounting package to improve metal balancing is fundamentally flawed if the data used are unreliable in the first place. The basic rule for correct sampling is that all parts of the material being sampled must have an equal probability of being collected and becoming part of the final sample for analysis. If this rule is not respected, sampling bias can easily be introduced. Unlike precision, which can be improved by replication, bias cannot be reduced once it is present. Sampling and sample processing procedures must therefore be carefully designed both to minimise bias and to obtain acceptable precision. The most suitable sampling location is the discharge point of a process stream, where increments can be obtained by taking a complete cross-section of the stream with a sample cutter. Sampling devices that take only part of the stream may introduce serious bias and must be avoided. The moisture content and wet mass of the material being sampled are of similar importance to chemical analyses for determining metal content. The accurate determination of moisture content is particularly difficult, because the moisture content of samples can change after the sample is taken, eg due to moisture evaporation. Hence, moisture samples need to be taken quickly and placed in sealed bags or containers that are impervious to moisture. The moisture content should then be determined without delay. To determine wet mass, a range of weighing methods are used in industry, including weighbins, weighbridges, conveyor weightometers and platform scales. The precision and accuracy of these methods vary considerably, so it is important to select a method with the appropriate precision and ensure that the weighscale is well maintained and regularly calibrated.

Jan 1, 2002

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

In mineral asset valuation the use of any valuation method requires the input of competent and independent technical professionals. A resource valuation must be as transparent as possible to allow others to assess the validity of their underlying assumptions. Materiality is a dominant factor in all valuations and a valuer should set out the basis for the subjective decisions made in this regard. Any valuation methodology must comply with the requirements of the law, practice notes and guidelines issued by the various relevant authorities and professional bodies. The valuation methodology chosen to value a mineral asset depends upon the amount of data available on that asset and the reliance that can be placed upon those data. Mineral assets generally fall into one of three broad categories, depending upon their state of development, ie whether they are at the exploration, development or operating stage. Naturally there are transition phases. Hence, there are ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects; Pre-Development Projects and Developing Mines; and Operating Mines. The features of each of these mineral asset status categories are described, mainly in terms of the confidence in the contained identified Resources/ Reserves. The various subjective methodologies available for the valuation of ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects -are specifically reviewed. The pitfalls in adopting a ""recipe"" approach are noted. It is the author's view that the Expected Value Method (based on the probability adjustment of the output of a Discounted Cash Flow/ Net Present Value model) has little application in the valuation of exploration mineral assets, so it is only briefly addressed. The methodologies reviewed are listed below. ò Multiple of Exploration Expenditure Method (expenditure based). ò Joint Venture Terms Method (expenditure based). ò Geoscience Rating Methods (eg Kilburn - area based). ò Comparable Market Value Method (real estate based). ò Rules of Thumb (eg $/Resource or production unit; % of in situ value). Some recent Prospectuses are used to provide examples of their misinterpretation and misapplication.

Jan 1, 1994

By Flloyd J. M

A continuous oxygen probe,incorporating a SIRO2 solid electrolyte oxygen sensor which measured the oxygen potential of a small volume of gas enclosed above the melt's surface,was constructed and tested. The oxygen potential of iron-silicate slags in equilibrium with solid iron in the temperature range 1250 to 1300¦C were measured continuously for tests of up to 40 hours duration. Results were in agreement with those of previous workers using gas equilibration techniques. Tests on non- iron buffered slags proved unsuccessful due to corrosion of the probe's component in contact with the slag and an alternative material is Required.

Jan 1, 1987

The demands of the economy require larger manufacturing facilities using greater quantit- ies of raw materials which must be mined, handl- ed, stockpiled and recovered with efficiency and dependability. All over the world, mining com- panies, steel manufacturers, power stations and process plants are not only seeking but finding methods of increasing outputs and'reducing costs in the field of materials handling. In mining bigger continuous mining machines and shovels, larger trucks and crushers are digging and processing greater quantities of differing materials which have to be handled and shipped at rates once thought to be impossible. To implement such schemes demands the blending of a lot of diverse-equipment, mining machinery, bins, feeders, reclaimers and it is here that the belt conveyor assumes a role of ever increas- ing importance. Significant developments have taken place in the seventies with respect to conveyor belt transportation; not only in the systems but also in the components which combine to make such systems work efficiently.

Jan 1, 1976

By Hossaini SMF

After reviewing the various approach es,namely, empirical,analytical.observational and numerical, a logical systematic approach is proposed for the estimation of compressive strength of coal pillars. In this approach first,uniaxial compressive strength of coal in pillars is estimated,taking into account the size effect and the effect of discontinuities. Next,the compressive strength of coal pillars is estimated by determining the stress distribution in the pillar and the Bieniawski strength criterion. The results appear to be compatible to the ones obtained by Wilson's method. The traditional pillar design equations give improper answers for deep workings.

Jan 1, 1991

By Struthers M. A

The basement contact zone, a major fault structure underlying the copper orebodies at Mount Isa, has a significant influence on orebody extraction. The zone is comprised of a variety of weak, barren lithologies which often create very difficult mining conditions, contribute to stope dilution, and have an adverse effect on concentrator recoveries.The geological characteristics of the contact zone are described, and the importance of timely, accurate geological information emphasized.A variety of mine design strategies have been employed to reduce the impact of the contact zone on orebody extraction. Some of these are discussed, together with current trends in the southern areas where orebody geometry and hence mining methods change markedly.Recent developments in ground support techniques, such as cable dowel reinforcement, have significantly improved ground conditions in the contact zone. An example of the methods employed to improve knowledge of ground behaviour is presented. The trend towards increasing automation and larger equipment requires larger excavations; consequently ground support practices and knowledge of ground behaviour must continue to advance. Rock mechanics investigations will remain an essential part of the mine design process.

Jan 1, 1990

By Turner T. M

The problem of metering fine particulate material at low flowrate is often encountered in metallurgical experiment. This note describes a feeder which wa developed to provide metered flows of copper sulphide concentrate in the range of 0'1-0'7 g/min.It is believed that the present device is easier to operate than previously described feeders (e.g. Hamor and Smith, 1971). It may have applications in the field of analytical chemistry, as well as in metallurgical investigations.

Jan 1, 1978

By Carter LC

Following the perception by the Groote Eylandt Mining Company of a need to further beneficiate a fines product, and preliminary metallurgical testing to demonstrate the feasibility of such beneficiation, a comparison was made of the various configurations of cyclonic heavy medium separators available. This comparison consisted of (i) a pilot plant test in which a dynawhirlpool (DWP) and a pump fed cyclone were compared, and (ii) a survey of operating plants using the systems under consideration. Little metallurgical difference was found-between the different systems. The gravity fed cyclone configuration was finally chosen based on a particular need to minimise degradation of ore and on a desire, in so isolated a location, to use established and locally supported technology.

Jan 1, 1987

By Etheride MA

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems an particularly prone to developing the complex fracture arrays, extreme local dilation and dramatic increases in permcahilit} that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits.

Jan 1, 1995

The Hall-Heroult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-Heroult cell- the electrolyte, the anode and the cathodes are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride-carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.

Jan 1, 1987

This paper covers only the energy uses of natural resources and does not deal with non- energy uses, which in 1975 were of the order of 10 per cent of the total consumption of energy resources. The United Nations `J' Series of Statistics ex- presses each of the various forms of energy in terms of its coal equivalent in metric tonnes and this basis is followed in this paper. One tonne of black coal (referred to as tce) has been taken as the equivalent of the following. 29 X 109 joules or 27.5 X 106 Btu 0.68 tonnes or 4.8 barrels of crude oil 750 cubic metres or 26.5 X 103 cubic feet of natural gas 1 ò5 to 3.3 tonnes of peat or lignite (world average 2.54; Victorian brown coal 3 0) 8055 kWh (at 3.6 X 106 joules or 3412 Btu per kWh at 100% efficiency) 2660 kWh at 33% efficiency of generation 50 grams of uranium present in natural uranium reactors (see note later under nuclear energy) 0.8 grams natural uranium in breeder reactors Nuclear and hydro electricity are expressed as the coal equivalent required to produce, at 33 per cent efficiency, the same amount of electricity. In other words, electricity produced by these sources is converted to its coal equivalent at the rate of 2660 kWh = 1 tonne coal.

Jan 1, 1978

By Townsend MG, Evans RB

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre- Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth.The raw material is crushed and fractionated to produce a product of less than 2 micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974