Search Documents

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

By T Akiyama, J A. de Castro, H Nogami

Blast furnace is a countercurrent moving bed reactor that produces pig iron from iron bearing materials like pellet, sinter or lump ore. The furnace has cylindrical shape and the lump solid materials are alternatively charged onto the top of the furnace. Hot air is introduced through tuyeres that are set on the lower furnace wall. Auxiliary fuels (pulverised coal, oil or natural gas) and raw materials (fine ore or fluxes) are injected into the furnace with blast air from the tuyeres. In front of the tuyeres, coke particles react with oxygen in the blast air and generate carbon monoxide. The hot reacting gas heats up the lump solids and reduces iron oxides in the upper furnace. In the middle height of the furnace, the reduced iron and slag are fused by the combustion heat and form the cohesive zone. The molten iron and slag that are generated in this region trickle down through the packed bed of coke particles and flow into the bottom of the furnace. Therefore, the flows of gas, lump solids and liquids exist at the same time in the lower part of the blast furnace.

Jan 1, 2000

By A Mehrani, F Zamani, A Dehghani

Vibrating screens play an important role in the dry classification circuit of Gol-e-Gohar iron ore processing plant. This circuit was designed to classify the autogenous mill discharge and produce a suitable feed, with K80 about 450 ¦m, for dry magnetic separators. Three parallel vibrating screens produce more than 50 per cent of the separatorÆs feed. The efficiency of the magnetic separator is greatly affected by feed size distribution. In this work, the JKSimMet 5.1 software was used as an analysing tool to assess the flow rates and USIM PAC3 software as the simulation tool to control and optimise the vibrating screens. Samples were collected and the circuit was mass balanced. Then the vibrating screen was simulated and adjustment parameters such as cut-point, bypass and imperfection factor were determined. The product streams of vibrating screens can also be predicted.

Jan 1, 2007

By G Kennewell

At 11 am Monday 8 September 1997, the successful detonation of the 5/9 Mass Blast at Pasminco - Elura was signified by the subsiding of æMt KevinÆ (a 15 m high earth fill mound). The blast was in response to earlier mine subsidence, which holed through to the surface affecting future stability of underground workings. The blast was a first for Elura which fires small tonnages regularly to avoid rapid oxidation of the ore. This paper discusses the strategy and the considerable planning that went into EluraÆs first blast of this magnitude in order to succeed first time round.

Jan 1, 1999

By L Manca, P B. Hills, D Tyler, N Pollington

This paper describes a collaborative project undertaken by Newcrest Mining Limited (Newcrest) and pitt&sherry to identify, develop and then implement global best practices to manage the exposure to inrush (dry and mud) hazards in underground mining operations. An extensive literature review was undertaken to identify past experience globally and the current state of knowledge and practice in managing inrush hazard. A key requirement of the literature review was the development of a list of guiding questions which would form a framework for approaching operators to discuss the topic, capture recent learnings and understand current operating practices to allow the development of a best practice solution. An initial cohort of 14 mines across four continents chose to contribute and detailed interviews were carried out by the project team. The outcome from the literature review, interviews with participating mines and various internal discussions was a comprehensive summary document detailing Basic versus Best Practice management of the inrush hazard. This document is being used as a gap analysis tool by Newcrest to assess and guide the management of inrush hazard at their existing and future operations. The summary document has also been provided to the participating mines for their consideration. The project is iterative and will continue to evolve as new experiences, knowledge and practices come to light.

Mar 15, 2021

By C J. Carr

The Ernest Henry Mine (EHM) is owned and operated by Xstrata Copper and is located in North-West Queensland, Australia. The mine is currently undergoing a transition from an 11 Mtpa open pit mine to a large sublevel cave underground mine producing 6 Mtpa. Due to a number of factors, including geometry of the pit and crusher depth, the decision has been taken to develop a hoisting shaft rather than inclined conveyors.During the feasibility study the strip and line shaft sinking methodology was preferred over blind sinking due to scheduling opportunities and interactions with level development. Other methods of sinking considered included large-diameter raise boring, which was rejected due to concerns relating to centreline accuracy. The strip and line decision was reviewed during the tender process where better than anticipated blind sink advance rates and costs were presented. This in turn enabled the higher cost of the blind sinking method to be justified by a combination of reduced risks including schedule and ground water management. This paper discusses the pros and cons of both strip and line and blind sinking methodologies in the Ernest Henry context including sinking rates and total schedule impacts of the two methods, the key risks associated with each method, cost implications of blind sinking and safety implications of the work methods in general. The paper then concludes with the reasoning behind the decision to change to blind sinking for the EHM shaft.

Mar 21, 2011

Real-time data collection and plant historians are becoming common place in mining and processing plants. This vast quantity of data must be turned into easily accessible and actionable information for all levels of the organisation.Queensland Nickel use a combination of Microsoft and SAP business intelligence tools to collect, cleanse, aggregate and present plant information to the appropriate people for supporting decision making in the business. SAP Business Objects, for visualisation, and SAP MII, for integration, allows complex and accurate metrics to be delivered as real-time dashboards. Designing a rigid data management architecture to segregate the data collection, integration and logic and visualisation into distinct logical layers, allows for rapid report development and greatly assists with IT maintenance, while also minimising the complexity of any customised programming. This type of architecture ensures a common data source for all business reports, ensuring one version of the truth. The past few years at Queensland Nickel have seen process and maintenance engineers spending considerably less time collecting and integrating data and spending more time analysing what is happening in the plant. Real-time reports and dashboards have been developed around the business needs rather than around the data. Two years ago Queensland Nickel introduced an employee bonus scheme based upon meeting monthly performance targets; an easy to use dashboard that allows everyone, from operators through to management, to monitor these metrics day-to-day.

Sep 26, 2011

By T Clemens, D Trumm

Adopting environmentally acceptable practices in New Zealand is a crucial requirement for mineral wealth development. Recent planned expansions in the coal industry have increasingly placed mining in the media spotlight. A lack of appropriate national environmental guidelines has resulted in inconsistent responses and assessments of current and prospective mine sites. Such inconsistencies have lead to delays in decisions on developing economic mineral deposits that may have only minor short-term impacts, and have also allowed unacceptable environmental management practices to continue elsewhere.   A research collaboration between CRL Energy, Landcare Research, University of Canterbury and University of Otago aims to provide regulator groups and the mining industry with a unified approach to the requirements of the Resource Management Act 1991, which is the legislation that predominantly drives the nationÆs environmental policies and guidelines. The tangible outcome of this research programme will be guidelines for an integrated decision-making framework based upon robust multidisciplinary science. The result of this unified process will facilitate the development of viable mineral deposits and prevent excessive environmental impacts.   The framework will be derived from a synthesis of four objectives. Objective 1 identifies potential water quality impact. This objective is based on a targeted geochemical study of the lithology and waterways of the West Coast and Southland. Objective 2 categorises the degree of impacts on the ecology of receiving aquatic ecosystems and determines the processes that drive aquatic ecosystem recovery. Objective 3 identifies best strategies to sufficiently manage impacted ecosystems, and to prevent future unacceptable impacts. Objective 4 combines the findings of Objectives 1 - 3 into a standard decision-making framework. The development of this framework development will include wide consultation with representatives of the mining industry and regulator groups. It is anticipated that this multidisciplinary approach will provide a robust and coherent, standardised system that will assist in achieving industry and environmental targets.

Jan 1, 2004

The purpose of this paper is to look at the costs of tailings disposal, and in particular the comparative costs of different disposal methods in different situations. Costs are often the hidden design parameter. We know that they are important but sometimes feel that it is not very respectable to talk about them in public. It is better from a public relations point of view for it to appear that the decision-making process is driven by environmental factors or best practice rather than looking for the cheapest option. But this presumes that the two are mutually exclusive and this need not be so. These issues are discussed later in the paper. It is also commonplace for the scale of the mining operation to change with time, typically involving increased throughput rates and total tonnage. New ideas in tailings disposal make their appearance. The regulatory attitude can change. Having made a decision about the disposal method at the time of original feasibility study and design it is easy to suppose that the mine is æstuck with itÆ. But that also need not necessarily be so. Careful costing of options may reveal that a switch in method could be cheaper in the long run. The designer will often tend to think in terms of initial earthworks and site development costs. Aspects of power consumption, labour, and periodic campaigns to move tailings pipelines and carry out embankment raises are either overlooked or not given the same emphasis. This can distort the evaluation process. It is productive to think in terms of dollars or cents per tonne as a basis of comparison, not just the total sums. Tailings disposal can cost from as little as 10 - 20 ó/t to over $1.00/t which is a big range. There may be good and unavoidable reasons for the high figure but there would need to be to justify being so far over the industry average. At the same time, mining and processing costs, at least for gold, are around $15 - 20/t. Viewed from this perspective tailings disposal will always be a relatively small component of the annual budget.

Jan 1, 2000

This paper firstly reviews the requirements for container and hopper design for reliable discharge. Discussion is then directed to the evaluation of the consolidation stresses acting in both in both the cylinder and hopper sections during both initial and flow conditions. Here the vast difference, especially in vicinity of the bin outlet, between the initial or filling and flow conditions is highlighted. This vast difference has major design and operation implications. A further major implication is that all bulk solids must dilate to flow. The opportunity to simultaneously attain reliable discharge and partial moisture removal is also examined.The selection of design parameters to maximise the consolidation stresses in both the cylindrical and hopper sections is detailed. In regard to the latter, it is recommended fine coal bins be discharged using low friction lined transition hoppers with large outlet spans. Such outlets will discharge fine coal in a relatively compacted state. This compaction state should exhibit minimum water retention and short term moisture uptake.

Jan 1, 1998

By C Katonga

Mindola mine is currently the deepest mine in the Zambian copper belt. Stoping is currently active to 1330 m below surface with long range plans indicating future production from 1590 m level. The orebody is tabular and dips between 55o to vertical. The thickness varies from 8 to 14 m. The vertical crater retreat method of mining was first introduced at Mindola mine in the late-1980s following several trials that helped define the design criteria for its application. Over the last ten years the method has been continually modified to improve safety and maximise ore production. For example, due to the weakness of some rock units within the orebody formation and the instability of the hanging wall, the last VCR slices are usually between 8 - 10 m thick, and efforts are being made to strictly apply shrinkage method in order to reduce dilution. Recent advances in mining technology in the areas of equipment, blasting techniques, rock mechanics and materials handling have been employed to increase the overall productivity of the mine. Large down-the-hole machines capable of drilling 165 mm diameter blast holes, up to 80 m long are used in stoping. Each stope produces up to 20 000 tonnes of ore per month and can last for three months. Heavy systematic ground support of VCR development has significantly enhanced safety for mining crews and equipment. Crater mining has not only improved productivity and enhanced safety, but also overcome various problems associated with conventional sublevel open stoping previously employed at the mine. This paper discusses the technical and operational aspects of vertical crater retreat mining at Mindola mine during the last ten years. The changes in mining method are often accompanied by changes in mine design, blast design, mining equipment, ground support and operating practices.

Jan 1, 2000

By Y Zhang, Z Zhao

The green production of the steelmaking process has urgent requirements for fluorine-free fluxes. In this article, a new solid waste-based slagging flux was applied in the external dephosphorisation test of low silicon hot metal to replace the traditional fluorite-lime dephosphorisation slag. The results showed that under laboratory conditions, the new flux was utilised for smelting low-silicon molten iron with a phosphorus content of 0.10~0.13 wt per cent, the temperature of the molten iron was 1350°C and the slag amount was controlled at 2 per cent. Within ten minutes of smelting, the dephosphorisation rate of the molten iron reached more than 50 per cent. When making slag with new flux, the slag melting time was about 40 seconds and the P2O5 content in the final slag was higher than 8 wt per cent. In the industrial test of a 150 t molten iron ladle, under the same molten iron conditions, an out-of-furnace dephosphorisation test was conducted in the Kambara Reactor (KR) process. The flux material consumption per ton of steel was 8~10 kg. Within 15 minutes of smelting, the dephosphorisation rate of the molten iron was about 30 per cent. During flux slag making, the slag melting time was about three minutes and the P2O5 content in the final slag was higher than 6 wt per cent. This new solid waste-based flux has significant cost advantages and outof- furnace dephosphorisation effects and is expected to become the benchmark for a new generation of fluorine-free steelmaking fluxes.

Aug 21, 2024

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

Milling operations at Misima Mine are discussed, with specific reference to the application of energy and cost saving concepts. Design stage innovations and post-commissioning developments are covered. General operational problems are described with specific reference to problems associated with operating in a remote location.

Jan 1, 1994

By W Polkowski, M Tangstad, M Wallin, J Jiao

Fe-26Si-9B (wt per cent) alloy has been identified as a potential high-temperature phase change material (PCM) due to its attractive properties, such as its high latent heat of fusion and low volumetric change during solid/liquid transition. For the successful utilisation of this alloy into thermal energy storage (TES) systems, the development of a cost-effective production method is essential. Presently, the Fe-26Si-9B alloy is produced by mixing FeSi alloys with either pure boron element or FeB alloys. However, the use of pure boron is financially prohibitive, and the carbothermic reduction results in high greenhouse gas emissions and high energy consumption in the production of FeB alloys. In this regard, our study proposes a silicothermic reduction method to produce Fe-26Si-9B PCM by using FeSi alloys and B2O3-based oxides. Accordingly, the influence of various parameters on the production process was investigated, including operating temperature, holding time, B2O3 content in the added oxides, and initial Slag/Metal (S/M) ratio. Based on the experimental results, the optimal parameters for producing FeSiB alloys with over 9 wt per cent boron were determined. Consequently, it was documented that the FeSi alloys and the added oxides enriched with 50– 65 wt per cent B2O3 should be subjected to temperatures ranging from 1550–1650°C, maintain an initial S/M ratio exceeding 1, and ensure a holding duration beyond 1 hr. Moreover, the energy consumption of this process was estimated to be ~1.86 MWh/t metal and the mass loss was lower than 7 per cent. Therefore, silicothermic reduction offers a sustainable approach for producing FeSiB alloys with a boron content above 9 wt per cent.

Jun 19, 2024

By C Gimber

Dust suppression is an important environmental control in most mining operations. The poorest quality water within a mine site is often used for dust suppression since it provides an effective means of reducing the volume of poor quality water. The ultimate fate of contaminants or salinity associated with water used in dust suppression is important to consider for optimising water management and assessing the environmental impact and life span and maintenance requirements of roads associated with dust suppression.The propensity for remobilisation of contaminants or salts depends on a range of factors such as the application rate, climate, road construction, water chemistry and soil geochemistry. This paper describes a typical study approach which could be used to assess the short- and long-term impacts of mine water application for dust suppression. The steps of the study are: reviewing the environmental setting, estimating water requirements for dust suppression, reviewing source water chemistry, developing a mass balance model and assessing the mobility and fate of contaminants with a geochemical model.This approach identifies which salt species are likely to form and whether they are prone to remobilisation. It is possible to quantitatively assess the risk of exporting contaminants or salt from roads and to refine the dust suppression strategy to minimise the environmental risk. The approach can be applied at mine sites to address regulator concerns, aid decision-making and improve the understanding of short- and long-term environmental risks.CITATION:Gimber, C, 2013. Assessing contaminant risk associated with the use of mine water for dust suppression, in Proceedings Water in Mining 2013 , pp 235-240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J Zhao, C E. Loo

The flame front is a narrow region in the iron ore sintering bed where coke particles combust. The maximum flame front temperature is as high as 1400°C. At high temperatures, the sinter mix components react to form melts, which facilitates material coalescence and the formation of dense sinter particles. It is well-established that flame front speed is an important factor influencing sinter productivity, sinter quality and fuel rate. In this work, the effect of suction, coke addition and mix moisture on flame front speed was studied in a pilot-scale sinter pot and also using the outputs of a recently developed theoretical model, which takes into account most of the significant physicochemical processes in sintering. Airflow through the bed has a large influence on flame front speed. A power law relationship between these two parameters means that increasing sintering airflow rate will lead to increased flame front speed, but the increases become smaller at higher airflow rates. Sinter pot test results showed that increasing coke addition decreased green bed permeability and increased flame front temperature, which resulted in increased flame front resistance and decreased flame front speed. Studies also showed that green bed properties are sensitive to sinter mix moisture level. The changes in green bed properties further influence the flame front speed and temperature.CITATION:Zhao, J and Loo, C E, 2015. Dependence of flame front speed on iron ore sintering conditions, in Proceedings Iron Ore 2015, pp 83–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C Zschiesche, alam, A Abadias Llamas, A K

An integrated experimental and thermodynamic modelling study of the phase equilibria in the FeOFeO1.5- SbO1.5-SiO2 system in equilibrium with liquid Sb and Sb-Ag metal has been undertaken to develop thermodynamic model of the Na-Si-Fe-O slag system with S-Sn-Sb-Pb-As minor elements based on the experimental investigation of the selected sub-systems. New experimental phase equilibria data at 575–1600°C were obtained for this system using high-temperature equilibration of synthetic mixtures with predetermined compositions in sealed silica ampoules, Fe3O4 basket in sealed silica ampoule, or Re foils, a rapid quenching technique, and electron probe X-ray microanalysis of the equilibrated phase compositions. Experimental results on phase equilibria in the Fe-Sb-Si-O+Sb metal system obtained helped to produce initial set of model parameters in the slag. The primary phase fields of quartz/tridymite/cristobalite (SiO2), 2 high-SiO2 immiscible liquids, olivine (Fe2SiO4), wustite (FeO1+x), spinel (Fe3O4), schafarzikite (FeSb2O4) and valentinite/ senarmontite (Sb2O3) were identified in the binary Sb2O3-FeO, Sb2O3-SiO2 and ternary FeO-Sb2O3- SiO2 systems. Further refinement, particularly the distribution of excess Gibbs energy among the ‘FeO’-Sb2O3-SiO2 and ‘FeO1.5’-Sb2O3-SiO2 interactions, required the study at more oxidising conditions. Oxygen potential was increased using an inert metal (Ag) rather than using the gas flow due to the high volatility of Sb-containing gaseous species. Liquid Ag-Sb alloys with low concentrations of Sb of a few percent were used. At these conditions, the concentration of AgO0.5 in slag was below 1 mol per cent, which had a small effect on observed phase equilibria in the system. In addition, important information on the solubility of silver in slags is produced, which can be valuable when treating electronic recycling materials or primary silver-containing ores through the Pb process. Two main areas were addressed: the spinel-tridymite boundary (40–70 per cent SiO2 in slag) and spinel liquidus near 15 per cent SiO2 in slag. This allowed to deconvolute the separate contributions of the FeO-Sb2O3(-SiO2) and Fe2O3-Sb2O3(-SiO2) systems.

Jun 17, 2024

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994