Search Documents

Modelling and Optimisation of Direct Reduction of Iron Ore by Coal in a Rotary Kiln

Sep 13, 2010

By A Marton

Concerns with crest losses have seen changes to a number of design and operating parameters to retain the integrity of the wall and the berms of the Kidston Gold MinesÆ Eldridge Pit. Until trials began in 1999 most final wall designs utilised large diameter blastholes up to the presplit row to achieve the wall angle. The berm crests were being lost, wall support requirements were increasing and affecting mining schedules and several fault areas were putting pit access at risk. Standard designs had been determined during the early mining years and while periodic modifications had been made there was a need for major blast pattern revision. This paper traces the development of wall control blasting programs over the years, relating designs to the geology and the evidence in the walls with the theories of the day and includes the recent trials that were conducted in what is a most unforgiving geology. Trials and improvements to ensure the walls were safe were conducted even as the mine neared its economic life. Instrumented monitoring of trials blasts has greatly increased the understanding of the damage criteria and enabled rapid revision of designs. Recent changes included reduction in presplit energy, charge redistribution and use of smaller blast holes for the trim patterns. Determination of a minimum proximity-to-final wall limit for production blastholes, establishment of the correct standoff to berm crests and walls and selective use of presplitting techniques for protecting crests have resulted in cost effectiveness, improved bench crest retention and an overall reduction in visible wall damage.

Jan 1, 2001

By A Kemp, I Taylor, S C. Lamoureux

Detailed landform designs were completed for six (integrated) iron ore waste rock dumps at a Western Australian iron ore mine site to meet closure objectives and to optimise material movements for closure. The designs were based on specific physical and geochemical properties of waste material and the design was undertaken to enhance long-term stability of the dumps and optimise material movements, and therefore minimise closure cost. Construction of the re-shaped waste rock dumps have been completed. Following construction, surface material characteristics were found to deviate from those used in the design assessment. Materials present at surface following re-shaping were generally finer textured than those sampled for modelling. It is anticipated that the embankment slopes may experience increased rates of surface erosion compared to the rates predicted from modelling and used in design. The finer textured material is thought to be generated from exposing finer material that has migrated into the coarser matrix over time or that was not present in the sampled top surface of the landforms. This is due to armouring processes over time and this phenomenon is likely to recur following further wet seasons. The majority of the waste materials present in the waste rock dumps were subgrade banded iron formations (BIF) and chert, which are generally competent and geochemically inert. Some waste material was known to have an elevated risk of erosion but present in relatively small quantities. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert). This paper presents the process from upfront materials assessment through detailed design to construction of the rehabilitated waste rock dumps, and post-construction sampling and testing to validate model findings.CITATION:Kemp, A, Taylor, I and Lamoureux, S C, 2017. Design to closure – construction of detailed rehabilitation designed iron ore waste rock dumps based on upfront site specific assessment, in Proceedings Iron Ore 2017, pp 353–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By I Gray

This paper examines the effects of the changes in stress that a coal may undergo as part of the drainage process. As a consequence of this, some coal seams will come to the situation that they have zero horizontal stress existing within them at the time of mining. The hypothesis of this paper is that this lack of horizontal confining stress means that on mining, the vertical stresses may be easily raised to a level where failure occurs. This failure may be accompanied by significant energy release from energy stored within the coal as well as that coming from the roof and floor. To determine the state of stress within the coal seam, the concept of the effective stress path that the coal passes through is examined and is found to be very dependent on the shrinkage of the coal with degassing, the Young’s modulus of the coal and its Poisson’s ratio. The Young’s modulus of the coal is important and has been found to be highly dependent on the state of stress within the coal. It may change by more than an order of magnitude.CITATION:Gray, I, 2014. The consequences for pillar stability of zero confining stress brought about by forced or natural drainage, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J P. Barkas

World demand for iron ore is far from peaking, and the substantial price decline that has captivated commentators since early 2014 is not the result of widespread misreading by producers of the prospects for global market growth. Recent price movements provide little useful insight into the industry’s longer-term fortunes, apart from reminding mining companies that their businesses need to be robust against the volatility and inescapable cyclicality of mineral commodity markets. It is timely to take a strategic view of the history and longer-term prospects for the iron ore industry and of Australia’s place in it.CITATION:Barkas, J P, 2015. Perspectives on the long-term outlook for iron ore, in Proceedings Iron Ore 2015, pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

By D J. Bradshaw, E M. Wightman, B Newcombe

Flash flotation plays an integral role in many of the gold and sulfide mineral concentrators around the world, and yet despite this widespread use, very little information on this unit process is available in the published literature. For operations to maximise the performance of their flash flotation circuits, understanding how these cells operate, the nature of the particles they target and how to predict whether a flash flotation cell should be used on a specific ore type is of vital importance. This paper provides a summary of the key findings of a large flash flotation research project based in the operating environment of a refractory gold concentrator. The influence of key flotation performance criteria including gas dispersion, residence time and particle segregation within the cell will be discussed and recommendations for process improvements will be made throughout. The nature of the particles within the flash cell will be examined, as will the impact on the type of particles that are passed to downstream processes when the flash flotation cell is taken off-line. The development of a laboratory method to determine whether an ore is suitable to undergo the flash flotation process is also presented for its potential to aid in flow sheet development and optimisation for new ores.CITATION:Newcombe, B, Bradshaw, D J and Wightman, E M, 2012. Into the belly of the flash à Insights into the mechanisms at work within a flash flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A Batnasan

The main techniques for removing phosphorus as an impurity element in iron ores are physical separation (eg magnetic separation, flotation) and chemical separation (acid leaching, alkaline leaching and bioleaching) processes. When phosphorus occurs in iron ores as phosphate minerals (eg apatite), physical separation techniques are available to remove the gangue minerals from iron ores. On the other hand, chemical separation techniques are suitable for reducing phosphorus levels when phosphorus is associated with iron oxides and hydroxide minerals (eg hematite and goethite) in iron ores. In this study, the dephosphorisation behaviour of high‐phosphorus iron ore was investigated using a combined alkaline roasting and water washing route. Roasting experiments were conducted in a laboratory electric muffle furnace using various concentrations of sodium hydroxide (0–50 g/kg-ore) at different temperatures (100–800°C), varying prolonged roasting times (0–2 h), and different particle size fractions (-45 – -250 μm) of iron ore. Subsequent water washing experiments were employed at various pulp densities (30–1000 g/L) and different times (30 s – 60 min) at ambient temperature. Hematite and goethite were the main minerals in the high-phosphorus iron ore identified using X-ray diffraction (XRD) analysis. The iron ore assaying 63.40 mass % Fe (total), 0.240 mass % P, 4.53 mass % SiO2, and 4.87 mass % Al2O3 were determined using X-ray fluorescence (XRF) analysis. The results showed that the dephosphorisation rate of the iron ore was reached 40 per cent under roasting with 50 g/kg-ore NaOH at 300°C for 2 hours followed by water washing for 30 s with a pulp density of 300 g/L, reducing phosphorus level from 0.240 mass % to 0.142 mass %. At the same time, the iron grade was reduced from 63.4 per cent to 59.5 per cent, caused by an iron loss. Results suggest that the phase transformation of goethite induces the dephosphorisation of high-phosphorus iron ore under alkaline roasting conditions

Aug 22, 2022

By the use of flotation tests it was confirmed that there are two functions of oxygen in sulphide mineral flotation. Sized samples of galena and chalcopyrite were sulphidized, washed free of excess sulphide ion, and then contacted with air-saturated water for certain lengths of time. The mineral was then transferred to a sealed laboratory flotation cell containing water with a known concentration of dissolved oxygen. Xanthate and frother were added and flotation continued for 1 min.Both the extent of mineral oxidation and the concentration of dissolved oxygen markedly affected the flotation of galena and chalcopyrite. The response to a change in either variable is dependent on the level of the other, but generally best flotation occurs with the maximum degree of air saturation of the pulp. Galena flotation is hindered by oxidation of the mineral beyond a small threshold amount but a similar effect for chalcopyrite was not observed...

Jan 1, 1967

For a large scale open pit mining and concentrating operation, on a low-grade disseminated ore body, it is possible to set an approximate lower bound on economically feasible operating scales and an approximate upper bound on economically desirable scales in a relatively straight forward manner. The optimum scale ofplanned operations, with respect to the objective ofmaximisation ofthe net value ofthe orebody, will have to be arrived at by iterative planning runs, but it may be expected to lie close to this upper bound. The effects of infrastructural costs and of the addition of a risk premium to the cost of capital, to form the discount rate for planning purposes, are considered theoretically and by worked example. It is concluded that a perceived special, unsystematic, risk should not be accounted for by the use of such a risk premium as this is inducive to placing a greater amount of investment capital at risk, for no greater return-rate to investment.

Jan 1, 1986

By W P. Darcey

Jabiru Metals completed a feasibility study on the Jaguar Base Metal Project in July 2005. The study was based on conventional truck haulage via a decline. Conveyor haulage was considered but not in sufficient detail to provide a meaningful comparison. The current study investigates the cost and productivity of alternative ore transport systems for the Jaguar project. The options considered are conventional underground truck, conveyor, road train, rigid frame truck, monorail haulage and shaft hoisting. Shaft hoisting was not considered in detail due to the high capital outlay for such a relatively short mine life of less than six years. This study goes beyond the common approach of evaluating haulage systems in isolation; it includes development costs, timing of ore production and costs associated with mine services as well as administration and milling costs. The results of this study indicate that the best haulage option for the Jaguar project is conventional truck using the Hitachi AH400 trucks. The net present value (NPV) for this option is A$8.13 million higher than the next best option namely the Kiruna E635 electric truck. The conveyor option has the lowest operating cost per tonne of ore but the longer development time negatively impacts on its NPV. The monorail option is considered impractical due to the number and length of trains required to achieve production targets.

Mar 21, 2011

Dr. Willett. I will start by answering one or two general points which have been posed. The first point is a question of liability of a seam to spontaneous combustion. Some seams are very liable to spontaneous combustion. Some seams are not liable at all except in most abnormal circumstances, and some seams have a liability somewhere between these two extremes. Dr. J. S. Haldane made the comment some 50 years or so ago that if you try hard enough you can make any coal seam in the world fire spontaneously. Many heatings have in fact occurred because the coal has been allowed to be ground up into a fine state and there has been air leakage through it for many years. This has resulted in spontaneous combustion which would not have occurred in some seams unless conditions had been very abnormal indeed. One comment I heard while listening to the discussions of one team was the importance of encouraging morale and the team seemed to go to the extent of suggesting that this was more important than the actual technical action taken. Though I agree that everything possible should be done to encourage morale, it must be in conjunction with the correct technical method of dealing with the Emergency.

Jan 1, 1973

Yallourn brown coal and its characteristics have been the subject of innumerable papers and discussions. The Lurgi process adopted for the production of Towns gas by the gasification of brown coal has been described frequently in literature.The application of the Lurgi process for the gasification of Yallourn briquettes has naturally lead to some unexpected problems. Rather than attempt to review the whole field of experience gained in the first two years of operation of the gasification plant at Morwell, this paper attempts to describe two problems encountered, peculiar to the fuel used, and the steps taken in overcoming them.THE PROCESS AND PLANTTo clarify the conditions surrounding the problems, it is necessary to briefly describe the gasification and cooling processes and plant.Brown coal briquettes are gasified in a pressure generator, using a mixture of steam and oxygen as a gasifying medium. Crude gas produced in the generator is washed and cooled in the waste heat boiler and coolers. Figure 1 shows an arrangement of the generator and coolers. The gasifying medium enters the generator through a hollow shaft in the base. This shaft drives the grate, which has three purposes: (a) to distribute the gasifying medium into the fuel bed; (b) to extract the ash from the fuel bed; (c) to support the fuel bed.Briquettes enter the top of the generator through the coal lock chamber and the fuel bed is maintained at a reasonably...

Jan 1, 1960

By N Madani, N Battalgazy

Geostatistical simulation has been widely used in mineral resource classification of metalliferous deposits based on international standards such as JORC code which is one of the most extensively used around the world for reporting the mineral resources and ore reserves alongside with objectives of the companies (Sadeghi, Madani and Carranza, 2015). However, the modeling process becomes challenging whenever the relationship between the variables of interest is complicated and cumbersome to model. This characteristic sometimes manifests itself in complex spatial and global cross-correlation measures, deeply depending on the formation and genesis of the deposit. The objective then is to generate the models that not only reproduces these significant characteristics, but also, it leads to a better understanding of a mineral resource estimation and successive decision-makings. In this respect, there are different approaches taking into account the spatial correlation structures, for which can be classified as independent simulation, co-simulation, and factor-based methodologies. In this paper, three techniques: Turning Bands Independent Simulation (TBSIM), Turning Bands Co-Simulation (TBCOSIM) and Projection Pursuit Multivariate Transform (PPMT); from those aforementioned approaches are selected to model two cross-correlated variables (Iron and Aluminum Oxide) belonging to an Iron ore deposit located in Brazil, in order to examine which methodology better reproduces the corresponding complexity in terms of local correlation measure. CITATION: Battalgazy, N and Madani, N, 2018. Mineral resource assessment in complex ore deposits based on international standards, in Proceedings Complex Orebodies Conference 2018, pp 79–81 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S Lockie, G Ivanova, J Rolfe

One of the consequences of mining expansion in the Bowen Basin region of Central Queensland in Australia has been a substantial increase in demand for housing, with subsequent impacts on housing and rental markets. Those pressures are reduced to some extent by a proportion of the workforce choosing to live in other centres and commuting to workplace for block periods. The main factors influencing location choice are: housing availability and affordability, basic urban services and lifestyle of the town and the town physical attractiveness such as coastal town. Low costs housing provided by the mining company acts as an attracting factor for some miners to live in the mining town. Recommendations for three short-term and two long-term strategic policy guidelines to address housing situation and location issues are provided.

Jan 1, 2009

Completion of a project requires two separate money-focused activities, namely economic evaluation of the cash flows underlying the project (before financing) and if the economics look promising, how it can be financed. Economic evaluation might be best led by a person with a technical-operating background, whereas financing might be best led by an accountant. Both should be presented in simple language with easy to understand models. Economic evaluation has a sad and bad history because it evolved from the fringes of accounting. Anyone can become a self-appointed practitioner. Some still take pride in mathematical complexity without realising that they distance themselves from the decision-makers and alienate other team members. Today there is no evaluation modelling consistency across the mining industry and this reflects poorly on our discipline. It is not tolerated amongst our peers in engineering and accounting. In 2009 æbest practiceÆ economic evaluation modelling is well defined. It is:easy to follow;tailored to its purpose;transparent;discipline, rigour and consistency;recording of all source data; and hencequick to audit. Mantra: If you cannot readily understand my model you do not have a problem, I do! The task of the economic model is to make the range of business cases underlying the decision easy to understand. Intellectual power is used to simplify the decision to its key issues and risks and to present the full range of possible business outcomes in readily understood terms. Project team members, management and the board must be able to make their decisions with æeyes wide openÆ. A steering committee should be established to develop a set of standards and practices that could be adopted for economic modelling within the industry. The industry needs to purge itself of the undisciplined economic evaluation modelling that now characterises the discipline.

Jan 1, 2009

By S Kundu, J Zanganeh, D Eschebach, B Moghtaderi

The concentrations of methane and coal dust vary from one location to another in underground coalmines. In the presence of an ignition source, such as static electricity, these mixtures can initiate explosions and consequently cause massive destruction. Research data can help in understanding the level of hazards and associated risk these flammable mixtures can produce. For instance, the level of peak explosion pressure and flame speed can be well understood from experimental and numerical research data. With this aim, methane–air mixtures and methane-coal dust-air mixtures were employed in a ducted spherical vessel. According to literature, the maximum value of peak explosion pressure can be obtained in vessels of spherical geometry when compared to vessels of other geometries. Thus the values of explosion parameters generated from spherical vessels can be incorporated in understanding the highest level of hazard that can occur in a real world scenario.In this study, the duct integrated with the vessel resembles any channel or pathway connected to a methane and/or coal dust rich area in the mine. Experimental investigations emphasise that the severity of explosion in the explosion zone transmits to the channel or pathway. The length of the channel or pathway also plays an important role on the values of explosion parameters. The greater the length of the channel or pathway, the higher the explosion pressure is and therefore the higher the destruction. Ignition energy and concentrations of methane and coal dust were varied in collecting experimental data. The data of explosion parameters thus obtained can be employed in addressing hazard mitigation strategies in coalmines.CITATION:Kundu, S, Zanganeh, J, Eschebach, D and Moghtaderi, B, 2017. Incorporating research data in addressing methane and coal dust fire, and explosion hazards in coalmines, in Proceedings Australian Mine Vent Conference 2017, pp 175–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By C Jones

Ridgeway Deeps is a block cave (BC) located down dip of the operating Ridgeway sublevel cave (SLC) mine. The BC is located approximately 210 m vertically below the lowest SLC level and approximately 1100 m below surface. Due to the mine layout containing a number of common pieces of key infrastructure the activities of both were interlinked.When investigating project construction options for the BC, a number of potential risks were identified including a conflict of priorities between operational and project deliverables and the varying safety and work methods between an owner mining approach in the SLC and a potential contractor workforce in the BC. This led to a review of the construction philosophy and the opportunity to utilise the existing SLC workforce as the basis of all activities in the mine. It was identified that a number of synergies existed with the current SLC operators and mine supervision including common work practices and the opportunity to build on the unique SLC skills of the operators and supervisors which could then be used at other Newcrest caving mines.With the commitment to this philosophy of building on the existing SLC crews and supervision the number of employees reporting through the superintendent underground operations grew from 95 to 245. This increase led to a restructuring of the reporting and work requirements of the superintendent, foremen and shift bosses. In order for the foreman and shift bosses to focus on running the larger crew numbers for the full 12 hour shift the mine superintendent became a pseudo human resources manager taking over all non-mine focused activities including overtime allocation and work and behavioural performance management. In simple terms, ensuring there were competent bums on seats when and where required. As the additional workers were recruited to top up the existing employee numbers, their employment history was used to place them in the most suitable roles. For example, those with building industry experience were placed on the civil construction crews and those with a farming background were used as truck drivers, nippers or on the service crews. To cope with the increased number of new starters a number of key personnel were seconded from the crews into the training group to act as on shift trainers. This initially caused a reduction in mine performance as the main operators were reassigned but it proved a valid move as the time for new operators to reach acceptable levels was significantly reduced with safe operating standards being maintained. This paper discusses how the Ridgeway Deeps Project was delivered on time and under budget whilst at the same time retaining its position globally as an operation to be benchmarked against.

Mar 21, 2011

Process Options for Difficult Arid-Region Nickel Laterites In the absence of the discovery of significant nickel sulfide deposits, the future of Australia's nickel industry will increasingly depend on cost effect processes for low-grade nickel laterites. The problems encountered with the West Australian HPAL plants, resulting in three of the four plants being shut down, have caused the industry to revisit atmospheric leaching options, particularly heap leaching. West Australian laterites are characteristically very varied in grade, chemical composition and mineralogy with the result that, thus far, one process does not fit all laterites. In this paper the leaching of an especially refractory ore is compared using column leaching of whole ore and atmospheric leaching and HPAL processing of ground ore. The key characteristic is the resistance of the goethite phase to acid attack with low-to-moderate temperature leaching conditions. The refractory characteristic is attributed to the stabilising influence of chromium and aluminium and possibly manganese substitution in the goethite crystal structure and goethite morphology. A significant three-fold increase in both nickel and cobalt extractions under atmospheric leaching conditions was achieved by the relatively simple modification of bubbling sulfur dioxide into the reaction vessel to create a reducing environment. Recoveries increased from <30 per cent to 90 per cent nickel and 86 per cent cobalt after 10 hours of leaching at 95¦C. An even greater improvement was achieved under ambient conditions by heating the ore to temperatures above 250¦C for 30 minutes. Subsequent leaching at ambient temperature gave an eight-fold increase in both nickel and cobalt recoveries after 14 days bottle rolling. Both methods could be optimised and implemented in such a way as to increase laterite reserves in conjunction with a heap leach operation but may be better suited to vat or closed tank processing.

Sep 13, 2010

By R Hoeppel, D Harimon, A Fisher

This paper examines the importance of examining the relationship between biology and geochemistry when designing a biopile to treat alkaline soils impacted by petroleum hydrocarbons. At a site in Nevada a large, unlined pit was constructed in a loamy sand soil and filled at regular intervals with a mixture of jet fuel, lubricating oils and waste solvents which were set on fire by the local fire department for training purposes. During its period of operation numerous chemicals were also dumped into the pit for disposal purposes, including dichlorobenzene and various chloroethylenes. As a result of these activities a large groundwater contaminant plume was formed. As a part of the site remediation process a decision was made to perform a limited source removal and excavate the top three to four metres of contaminated soil from the burn pit and place it in an engineered biopile. The location of the training pit is in a heavily mineralised basin where the background sulphate level in groundwater exceeds 5000 ppm. Due to naturally occurring biodegradation of the petroleum hydrocarbons a large portion of the sulphate was converted to sulphide which deposited in the soils as marcasite in the anaerobic soils. The initial attempt at soil remediation was to use a forced air treatment scheme that had worked well in small scale laboratory testing. Unfortunately, when attempted in the field on a large scale, marcasite reacted with atmospheric oxygen resulting in internal biopile temperatures exceeding 90¦C resulting in the virtual sterilisation of the soils without remediation occurring. In order to solve this vexing problem Pintail Systems, Inc developed an anaerobic culture that allowed the pile to be operated under anaerobic conditions. Within three months the biopile successfully demonstrated on a large scale significant biodegradation of the refractory petroleum hydrocarbons.

Jan 1, 2004