Search Documents

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

In a previous paper of this series (1) ,t it was shown that during the creep of single crystals of lead, deformation proceeded to some extent by means of slip on the octahedral plane. This was demonstrated by the formation of slip lines on the surface of the specimens. At first, a few broad bands appeared after a small amount of extension had taken place; then, as extension proceeded, more and finer lines made their appearance until the whole of the specimen surface was covered.The present paper deals with the process of deformation of the creep specimens as revealed by X-ray examination..By the use of this method, the changes taking place in the crystal structure can be observed.EXPERIMENTAL METHODThe method of preparation of the specimens, their size and the purity of the lead employed have been reported elsewhere (1). At frequent intervals, the specimens were dismantled from the test rack and X-ray back reflection photographs were taken. The specimens were so marked and set up on the X-ray machine that the same spot on the specimen surface was always examined.Copper radiation was employed, the tube voltage and current being 45 kV. and 25 m.a. respectively and the exposure time 2 hrs. The slit diameter was 1 mm.

Jan 1, 1941

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The Gold Ridge Mine is an open-cut gold mine in the Solomon Islands. The mine is owned and operated by Gold Ridge Mining Limited, a wholly owned subsidiary of Ross Mining NL. At the invitation of the Solomon Island Government, project construction commenced in July 1997 and gold production commenced in August 1998. The mine is the countryÆs first, and represents a major milestone in the development of the Solomon Islands. At the time of project approval and construction, there was a growing awareness in the country of the potential impacts of mining in the tropics, partly due to unfavourable publicity surrounding a number of other mining operations in the Pacific region. The management of environmental impacts was therefore an important consideration in the approval of the project, and continues to receive a high level of attention from the Government and community. Ross Mining did not commit to the Gold Ridge Project until it had satisfied itself that all waste rock and tailings could be safely contained on-site, and that the standards normally expected of a mine in Australia could be met. Ross Mining approached the approval, construction, and operation of the Gold Ridge Mine with a set of operating principles that met Government and community concerns. These were:best practice environmental management; operation of the mine in accordance with standards expected of mining operations in Australia; independent peer review of key technical aspects; on-going consultation with Government and community; and equitable transfer of wealth to landowners and the local community. As a consequence, the Gold Ridge Mine has developed into a successful mining operation with a high level of support from local landowners, the general community and the Central and Provincial Governments of the Solomon Islands.

Jan 1, 1999

By S Lal, S Rost, Q Williams, K Collerson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Shoshonite suite (absarokite-shoshonite-banakite) and adakite-hosted epithermal Au deposits are a feature of circum-Pacific magmatism. Fijian examples include Tavua (Emperor) and Tuvatu on Viti Levu. New discoveries of shoshonite suite and adakite-hosted epithermal Au mineralisation have been made in the southern Yasawa Islands and in central-northern and central-western Viti Levu. The Fijian shoshonites define four NE–SW trending suites. The oldest is the northern 7.9–5.0 Ma Yasawa suite, followed by the 4.7–3.5 Ma Sabeto–Tavua–Rakiraki suite in northern Viti Levu, the 4.7–4.2 Ma Yanuca–Vatulele suite approximately 20 km south of Viti Levu and the 3.4 Ma Astrolabe suite approximately 75 km further south. Shoshonite suite lithologies with 3.8–3.0 Ma ages also occur in the Lomaiviti islands between Vatu-Cake and Moala, to the east of Viti Levu, defining a trend oblique to the NE–SW shoshonite belts. Seatura, a 3.3–2.8 Ma ocean island basalt (OIB) volcano, sits at the northern end of the Lomaiviti trend shoshonites. Trace element/isotopic chemistries indicate that shoshonite arc magma genesis involved the melting of a hydrated supra-subduction zone mantle wedge and also a lower mantle-derived plume (OIB) component. The upwelling plume provided heat for melting and possibly Au enrichment. Accessing the melt generation zone associated with the plume required a slab conduit or window. Such slab windows form by tearing during subduction or occur at slab edges. Adakites form by plume-induced slab melting. The four NE–SW Fijian shoshonite suites are interpreted to occur in back-arc extensional zones above a slab window (tear) that migrated southward during rollback of the New Hebrides–Vanuatu subduction zone. The plume (Seatura OIB) that is interpreted to have caused mantle wedge melting and formation of the Lomaviti trend shoshonites was focused along the interface between the north-dipping Vanuatu–New Hebrides subduction zone and the west-dipping Tonga subduction zone, which we have seismically imaged at approximately 400 km depth. Our model ‘cracks the metallogenetic code’ for shoshonites and adakites and has regional and global implications for Au exploration.CITATION:Collerson, K, Lal, S, Williams, Q and Rost, S, 2015. Cracking the metallogenetic code for Fijian epithermal gold mineralisation , in Proceedings PACRIM 2015 Congress, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

By J T. Carswell

Best practice mine sampling should provide a detailed quantification of all potential sources of error at each stage of sampling, sample preparation and assaying.Quality assurance (QA) should include testing for and quantifying potential sampling errors, and should be the basis for establishing ongoing sampling protocols, should set error limits and define quality control (QC) procedures. QA should be within the framework of Theory of Sampling (TOS) but may not involve the estimation of the sampling constant and the application of Gy’s formula.Best practice QC should be carried out efficiently and in a timely and cost-effective manner with regular reporting against the guidelines established by QA.This paper provides an assessment of, and checklist for, current best practice sampling QA/QC with examples from operating gold mines including the QA/QC of underground (UG) reverse circulation (RC) grade control.CITATION:Carswell, J T, 2017. Best practice sampling QA/QC for gold and base metal mining – including how to assess the applicability of underground reverse circulation grade control sampling, in Proceedings Tenth International Mining Geology Conference 2017, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By A B. Christie, S C. Cox

Effective land-use planning requires accurate knowledge of mineral resource potential. Mineral companies during reconnaissance exploration, feasibility investigations and mine development also use this type of analysis. The Institute of Geological and Nuclear Sciences is undertaking a two-year project reviewing the resource potential of the West Coast of the South Island of New Zealand. Spatial prospectivity models have been developed as part of this resource assessment process, using computer based statistical pattern recognition techniques to delineate areas that are prospective for mineral deposits and to test deposit genesis models. Digital GIS data-sets of mineral occurrence were correlated against geology and exploration information. The distribution of mesotherrnal shear zone gold deposits in the Reefton Goldfield, were examined against geological data-sets from both the regional (QMAP) and local prospect-scale mapping. Weights of evidence analysis generated a correlation matrix that highlights relationships and degrees of association that might otherwise not normally be recognised.   Mesothermal shear zone gold deposits have strong positive spatial correlations with Greenland Group host rocks and areas with moderate to high quartz vein densities; moderate-strong positive correlation with regions <500 m from folds, with regions <600 m from faults and five to eight kilometres from granite contacts; moderate correlations with Ntrending fault and fold segments; and no/weak/poor correlations with fault intersections, fold-fault intersections, bends in regional structures and magnetic and radiometric data. The regional and prospect scale data sets give different results, with the more detailed prospect scale mapping giving generally better correlations. This emphasises the value of detailed geological mapping in the exploration process.   Maps generated by prospectivity modelling consistently highlighted areas of known mineralisation and generate targets where follow-up investigation is warranted. The prospectivity per unit area provides a measurable value that should change as new information comes to hand and, in addition to highlighting targets, can be used to measure the impact of increased exploration expenditure and assess the effectiveness of exploration investment.

Jan 1, 2001

By I R. Souza

At the mining industry, there are several uncertainties that may affect the mobile mining equipment fleet sizing and usage, such as commodity supply and demand, which impacts the mineral price, environmental licenses to allow operations and strategic decisions made by the own mining company. Due to that, it may happen to acquire a mobile mining equipment for a specific site and before it finishes the entire forecasted life cycle, the machine gets idle on that operation and a decision must be made regarding this matter. On large mining companies with several sites, equipment transfer provides a good solution to solve this issue and at the same time it provides operational flexibility and allows to use the equipment until the initially planned working hours. This article presents a method to compare technically and financially whether it’s more feasible to transfer a used equipment or to buy a new one. In other words, we will compare a brand-new machine versus a used one in terms of safety, net present value (NPV) considering both capital expenditures (CAPEX) and operational expenditures (OPEX), technological obsolescence, risks, equipment maintenance reliability and lead times. Although it’s not the main purpose of the paper, it will also be briefly discussed the importance of having a considerable amount of backup equipment to handle low likelihood and high consequence risks that may materialise. This backup equipment portfolio is particularly important to avoid loss of sales and profits in case the production plan changes and it demands further equipment than initially planned to cope with the forecasted production.

Nov 8, 2021

By J Coombes

There is much debate on the Competent Persons qualifying criteria for providing classified resource estimates for public reporting. The CRIRSCO family of codes including the JORC Code, SAMREC, PERC and NI43–101, require Competent Persons to have at least five years ‘relevant’ experience and belong to professional bodies. These codes provide further, albeit vague, guidelines to assist individuals with their personal decision to take on the mantle of ‘Competent Person’. There is a risk, however, that these qualifying criteria can result in ill-prepared Competent Persons whose actions and recommendations would undermine their own reputation and that of the organisations that employ them; the integrity of the profession and the principles based reporting systems; as well as the stability of stock markets that rely on these estimates.Based on doctoral study on the development of professional competency within the mining industry, this paper presents an evaluation of the suitability of the current qualifying criteria as well as an analysis of alternative criteria. The research included a series of interviews with industry experts and an online survey of resource geologists. Semi-structured interviews provided a sense of experts’ expectations and interpretation of the current definition of ‘Competent Person’. The comprehensive online survey included a self-assessment, a series of situational questions designed to evaluate responses to typical resource geology scenarios and a set of open-ended questions relating to factors contributing to competency development.A summary of the data analysis, interpretation of the results and a set of recommendations for revised ‘Competent Person’ qualifying criteria are presented. This paper contributes to the conversation on what makes a person suitably qualified to report classified resource estimates and provides practical targets that can be used in the professional development of resource geologists.CITATION:Coombes, J, 2014. Redefining Competent Persons criteria for resource geologists, in Proceedings Ninth International Mining Geology Conference 2014 , pp 153–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Production targets are the basis for almost every decision made by operations personnel in the daily operation of a concentrator. It is the production targets that determine how the plant is operated and therefore determine its efficiency. However, to achieve maximum plant efficiency production targets must be relevant to the process and achievable.In RoseberyÆs case, for many years, production targets were taken from budget data which, with the exception of mill feed tonnes and grades were carried forward from the previous budget. The zinc concentrate grade target was fixed at 57 per cent Zn, a long-term average; it was the accepted æstandardÆ for Rosebery. Historical data showed this target was never consistently achieved and plant efficiency was highly variable.Investigations into the possible causes for the variable performance ruled out plant and mechanical issues. Despite the Rosebery concentratorÆs age the plant and equipment are more than serviceable and reliable. The mineralogy of the ore and specifically the iron content of the sphalerite was found to be the most significant determinant of zinc concentrate grade. It was found with increasing frequency that the zinc grade of the sphalerite in the ore was below the zinc concentrate grade target. Consequently on these occasions attempts to meet the required concentrate target destabilised the process resulting in plant inefficiencies.Using the correlation between iron and zinc, data modelling was able to accurately predict the maximum zinc concentrate grade achievable for any ore type. By using on stream analysis instrumentation the operations personnel are now provided with constantly updated concentrate grade targets. By knowing the mineralogical limits of the ore at the time it is being treated process stability is maintained allowing plant efficiency to be optimised. This has resulted in a step change in plant performance and a significant increase in revenue.CITATION:Harris, G R, 2012. Developing and implementing ore-specific targets for the Rosebery Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 321-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

CONTENTS: Broken Hill The mixing stations.Operating and mixing apparatus.Pulp distribution.Stope preparation.Filling procedure.Consolidation of old fill.Drainage:Pulp density tests. Life of sand pipe lines.Results.Advantages and disadvantages.Conclusion and acknowledgments.General remarks on South Limited.Mining methods.History of stope filling in Broken Hill.Need for a new and better filling method and transport system.Initial experiments with hydraulic stowing.Source of the sand.Water Supply.Signalling system.GENERAL REMARKS ON BROKEN HILL SOUTH LIMITEDThe South Mine, property of Broken Hill South Limited, is situated at Broken Hill, N.S.W., Australia, towards the southern end of the main lode.The leases (M.L's 7 and 8)' cover a length of 2,400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1,940 feet below the collar of the original main shaft and to 825 feet below sea level.Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30,000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet.A typical assay for a monthly period is 14·40/0 Pb., 5·6 ozs. Ag., and 11· 60/0 Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and 'zinc concentrates produced are railed to other centres for the extraction of the contained metals.MINING METHODSMining practice throughout the field varies only in minor details. The ore-bodies forming the Broken Hill Lode lie within complex folds arranged along a shear and vary in size and mineralogical associations, but all the mines have similar types. Some of the ore-bodies have weak walls, but the chief difficulty in mining is caused by "heads" and "flaws" in the ore.Besides these local weak areas there are ground movements-referred to later-of varying magnitude extending throughout the central portion of the lode where the large ore-bodies, several hundred feet wide, approached the surface.

Jan 1, 1944

By S McKinley

"The White Mountain sediment-hosted gold deposit is located in north-eastern China. Mineralisation is associated with silica–hematite–altered polymict breccias that occur within dolomite at or near the contact with overlying sandstone. Economic gold grades are controlled by the distribution of the polymict breccias and can transition rapidly to low or zero grade over short distances. This results in sharp and highly irregular ore contacts on whose accuracy proper stope design and ore control is reliant at this blasthole underground mine.Short-term planning and ore control utilise a grade control model created from infill drilling and grade control sampling (ie face and wall sampling). Typically, the grade control model was maintained by time-consuming manual editing of earlier made contacts to incorporate any new data. This approach also was quite error-prone due to: the complexity of the breccia and ore grade contacts irregularly oriented and/or insufficiently dense drill holes inconsistent incorporation of grade control sampling. These errors resulted in unplanned dilution and ore loss due to inaccurate interpretation of the ore contacts.The primary advantage to implicit geological models over conventional, manually-built wireframe models is that they can be updated very quickly and frequently. In a mine setting, the power and efficiency of using an implicit model is greatest where the use of manual inputs or editing can be minimised. Recently a workflow was set-up for the mine geology team to create an implicitly-modelled ore shape for short-term planning needs by using all data, especially all grade control samples. The resultant 3D shapes provided metre-scale accuracy and consistently reconciled complex ore geometries much faster and to a higher degree of quality relative to the wireframe model. The mine stakeholders can now obtain an accurate ore model that will always be in sync with available data.CITATION:McKinley, S, 2017. Application of implicit geological modelling to improve the grade control process at White Mountain gold mine, Jilin Province, China, in Proceedings Tenth International Mining Geology Conference 2017, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By M Yahyaei, P Knights, M S. Kizil, J Qu

Digital Twins (DTs) are transforming business operations across many industries through their accurate representations of physical entities enabled by IoT technologies.

Sep 1, 2024

By Litvinenko V. I

Being a source of structural materials for many centuries, the modern image of the ferrous metallurgy is burdened with obsolete technologies with disregard towards new environmental protection requirements. The production cycle of metallurgical products have two clear-cut stages: I . production of liquid metal and casting into steel billets; and 2. processing of steel billets in solid state under high temperature to produce various shapes and profiles of metal products. Plastic deformation of metal at the second stage is least associated with environmental pollution and is presently being provided with more and more advanced equipment.

Jan 1, 1999

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By Huleatt M, Perkin D, McLeod I, Mock C, Pratt R, Gourlay A, Timoney E, Knight N, Ward J

Generally speaking, Australia's reserves of its more important minerals (in terms of export earnings) are adequate to sustain forecast rates of production to the year 2000. The rate of forecast production increases of these commodities (aluminium - whether as bauxite, alumina or metal, black coal, iron ore and ferro-alloy minerals, base metals, tin, uranium, and mineral sands) reflects a well- ordered and sustained growth phase of Australia's mineral industry.

Jan 1, 1981

By J Fraser, M Scoble

Within the past decade, incidents of mining–community conflicts have grown dramatically and represent one aspect of a phenomenon known as social risk. Research published in 2014 indicates that a lack of social acceptance is now a leading and costly cause of delays for mining projects.The rise of social risk, complemented by the need to earn the trust of an increasing number of stakeholders so that mining projects can be developed effectively, is problematic for the industry. Conflicts are occurring in situations where companies are fully compliant with regulatory and legal requirements, despite initiatives by mining companies to earn social acceptance and despite the proliferation of tools to support corporate social responsibility. Intensifying the impact of social risk is the fact that it has increased during a time in the global mining sector when companies have had to grapple with declining commodity prices, increasing capital costs and debt levels and the challenges of mining lower-grade deposits.This paper will explore a hypothesis that in today’s interconnected society, social risk in the mining sector constitutes a legitimate business risk that must be managed strategically. The reality facing mining companies is that information, once considered confidential, now travels quickly on social networks and via a growing number of groups and individuals that have earned a legitimate right to be classified as stakeholders in projects that affect their communities. To be successful, it is suggested that companies will benefit from increasing internal collaboration and providing training to equip teams to mitigate social risk to mining projects and protect reputation capital. The paper is based upon PhD research being undertaken to assess the points of intersection between social risk and social responsibility during the construction stage of greenfield mining projects.CITATION:Fraser, J and Scoble, M, 2015. Mining–community conflicts – can the future mining sector transform social responsibility?, in Proceedings Third International Future Mining Conference, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015