Search Documents

By R J. Everett

The mining industry is beginning to adopt quality systems based on the requirements of International Standards for quality assurance, such as the ISO 9000 series. Indications from similar industries are that considerable benefits are to be had from their adoption. This paper describes the use of the International Standard ISO 9001 for quality assurance within BUKA Minerals Limited. This provided guidance for the development of a clear statement providing agreement on the processes to be followed and the outputs required when dealing with outside service providers. Discussion focuses on the interaction with BUKAÆs consultants and contractors during the specification stage, resulting from the application of quality assurance techniques. Risk analysis was used to identify and manage the risks associated with the companyÆs contract for geotechnical and mine design services and the tender for a mine development program of work during the feasibility stage of the project. Setting acceptance controls for the deliverables from such contracts is traditionally fraught with difficulty. BUKA used Failure Mode and Effect Analysis for exposing underlying risks that were not effectively being countered. The briefs were reviewed and additional controls were developed to manage the risk. These controls have provided clearer instructions to the consultants and contractors, indicated audit points for the company and defined the deliverables. There exists within the company, and among its outside service providers, a clearer understanding of what is to be achieved and how it will be measured. The process has imparted considerable confidence to both parties on how the work will proceed and what outputs are to be provided. Some discussion is provided on how quality principles are being applied throughout industry and commerce, generally, and how they may apply to the mining industry. The paper argues that, far from being an appendix to the tendering process, Risk Management should be a mandatory step integrated into the definitions of the work.

Jan 1, 1998

By A Sturgess, P McKenna, P D. Erskine, D Doley, V C. Glenn

For more than four decades, rehabilitated lands in the Bowen Basin have been planted with buffel grass (Cenchrus Ciliaris), which is often used to provide rapid, stabilising and erosion reducing cover to reshaped landforms (Erskine and Fletcher, 2013; Harwood, Hacker and Mott, 1999; Grigg, Shelton and Mullen, 2000; Naidu et al, 1997). Historically introduced to Central Queensland and encouraged by pastoralists in the early 1900s (Humphreys, 1967), the species has been extensively used by mine managers in seeding mixes (Coaldrake and Russell, 1970; Edye, 1975), and the invasive nature of the grass has led to the monodominance in rehabilitated areas of semi-arid Central Queensland. With 40 open cut coalmines in Central Queensland (Department of Natural Resources and Mines, 2015), a considerable amount of land is either disturbed mine footprint (156 200 ha) or rehabilitated (29 200 ha) (Dale, 2015), and the bulk of rehabilitation consists of relatively young (<30-year-old) developing ecosystems, with demonstrated biomass fuel loads up to 20 t/ha (Grigg, Shelton and Mullen, 2000).Uncontrolled fire poses a significant risk to rehabilitated landforms that are located in close proximity to mining infrastructure, neighbouring communities, open pits with exposed flammable coal seams and flammable stockpiled coal resource. Mine lease holders in Queensland have the added responsibility of managing and protecting any endangered regional ecosystem communities, and flora and fauna listed federally under the Environment Protection Biodiversity and Conservation Act 1999 or the State Vegetation Management Act 1999; as well as, any culturally significant sites such as scar trees or middens that are found on-site. Additionally, uncontrolled fire in rehabilitated landscapes poses a significant risk to mine site closure goals, with the potential to create altered states and stalled ecological trajectories (Grant, 2006). CITATION:McKenna, P, Glenn, V, Erskine, P D, Doley, D and Sturgess, A, 2016. Fire behaviour in buffel grass dominated mine site rehabilitation in Central Queensland, Australia, in Proceedings Life-of-Mine 2016 Conference , pp 158–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By Y Peng, C Burns, Y Mu, R A. Lauten

In both laboratory flotation experiments and from analysing the composition of the lead concentrate at the Boliden Tara lead-zinc mine in Ireland, it has been found that F-250 may replace cyanide as a pyrite depressant. Replacement or reduction of the cyanide consumption is highly desirable from a safety perspective given the toxicity of cyanide. Scrutiny of results from the plant trial indicate that F-250 is less efficient as a cyanide depressant when the flotation feed contains high levels of pyrite. Statistical analysis of the results does not capture this trend, illustrating a need to collect more data at higher pyrite ore levels. A recent model proposed for biopolymer-induced pyrite depression is reviewed and discussed next to the suggested mechanism for pyrite depression via cyanide. Review of the interactions causing pyrite depression point to different manners in achieving depression. In light of the less efficient F-250 pyrite depression at high pyrite levels, it is speculated if the two depressants may act synergistically at high levels of pyrite in the feed. CITATION:Lauten, R A, Burns, C, Mu, Y and Peng, Y, 2018. Pyrite depression at Boliden Tara using F-250 – a biopolymer, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The following brief paper is intended, to apply to the concentration of the silver-lead ores at Broken Hill, New South Wales, generally, but more particularly to the process as applied to the ores in the Block 10 mine. The attached plans are similar inmany respects to those prepared, recently for the Block 10 company.Most of the information here given is already well known to those members who are conversant with the concentration practices of this field, but it is the writer's object to give just a few of those figures which he found difficult to obtain when first engaging in practical work. At that time no text-books were at hand from which it was possible to get sufficient details for practical working purposes.It is first supposed that the mine has been thoroughly explored and has been found to contain a lbde sufficient in size ·and quality to warrant the erection of a concentrating plant. The points then to determine are:-(1.) The quantity and cost of water available for steam-making and ore-dressing purposes.(2.) The most convenient site for the mill.

Jan 1, 1904

By O A. Cottrill, G A. Oldfield, S B. Nowell

Host-rock û wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.   Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

The rush for alternate iron-units in the last few years spurred a true outbreak of new alternate iron units projects many of them incorporating new process in what can be classified as the.most fruitful and innovative technology outburst, in the steel industry, in decades In a recent paper we focused on what would be, in our opinion, the ultimate targets of the use of alternate iron-units by mini-mills: 1. to improve quality, 2. to reduce cost, 3. to increase plant productivity, and 4. to improve `supplyability'. With these objectives in mind liquid hot-metal, among all possible scrap substitutes, has been proven to be by far the best. This conclusion stems from many different authors who have reviewed the `value in use' of hot-metal against other alternate iron units and measured its impact on steel-shop productivity and cost (Figure 1).

Jan 1, 1999

There is a lack of information concerning the movements of water on the continental shelf, particularly with regard to data obtained regularly over significant periods of time. The Horace Lamb Centre for Oceanographic Research has recently deployed data acquisition systems on the sea bed off the coast of South Australia to record tides, swell, and ocean temperatures. Some of these early records are described. The swell data are pertinent to future offshore operations with drilling rigs, barges, and other equipment, while the temperature variations give evidence of significant bottom currents, apart from those due to swell.

Jan 1, 1971

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By J L. Mauk

The Gladstone Hill area hosts epithermal veins similar to those at Martha Hill, which is less than one kilometre away. There are several vein types in the Gladstone Hill area including (1) pyrite-marcasite, (2) quartz, (3) base metal sulfide, and (4) calcite. Pyrite veinlets formed first, whereas the quartz and carbonate veins formed later. The base metal sulfide vein occurs at depth and is predominantly comprised of quartz and chlorite intimately intergrown with pyrite, sphalerite, galena, and rare chalcopyrite. Platy calcite and massive calcite veinlets were the last vein types to form. Several vein textures occur in the Gladstone Hill area, including colloform and crustiform banding, lattice-bladed, zonal, comb, massive and feathery textures. Crustiform banded veins are the dominant texture and contain variable gold-silver grades. Colloform banded veins consist of ubiquitous quartz and minor chalcedony with gold grades as high as 60 g/t. The lattice-bladed texture forms from the deposition of calcite, which has been replaced in many samples by quartz, indicating that boiling and later cooling has taken place. Unreplaced platy calcite only occurs at deeper levels (>300 m). Zonal and comb textures are preserved in quartz and late-stage amethyst veins. Feathery textures within quartz are commonly associated with breccias and some colloform banding, and with significant Au-Ag grades.   The homogenisation temperatures (Th) of primary and secondary inclusions in quartz, amethyst and platy calcite range from 166 to 274¦C, with salinities <1.3 wt% NaCI equiv. The presence of vapor-dominated inclusions and primary fluid inclusions in platy calcite suggests that boiling occurred intermittently throughout deposition. The veins formed under a relatively flat lying paleowater table that occurred 280 - 300 m above sea level. The fluids involved in vein formation were alkali chloride in composition and low in CO2.

Jan 1, 2001

By Senanayake G

A sample of crude copper powder produced by the CLEAR Process was refined by dissolution and recovery in sulfate media using the Parker Process. The Parker Process offers an alternative method of copper recovery to electrorefining and allows a range of Eh and pH conditions to be used to provide further discrimination of impurities. High purity copper powder was recovered by the Parker Process even in the presence of added impurities when the Eh and pH was maintained near constant throughout the refining step.

Jan 1, 1984

By Martinick WG

In July 1986, Cable Sands (W.A.) Pty Ltd commenced mining for mineral sands at Minninup, approximately 16 km south of Bunbury, Western Australia.The area being mined is from the heel of the foredune to the rear of the hind-dune. The vegetation is mostly native vegetation with some old degraded pasture.The mining operation will be by suction cutter dredge, with continuous dredging, mineral separation and re-depositing of the sand.

Jan 1, 1986

Elimination of zinc by the reduction of iron works dusts is examined. The process consists of blending, filtration, drying, balling, preheating and reduction in the rotary kiln. Dust slurries and dry dusts are mixed and stored in slurry basins and the blended slurry is filtered. In the balling process it is important to make green pellets which will withstand Thermal shock in the preheater and rotary kiln. Preheating to about 2000C is preferred to ensure effective use of coke fines in the blast furnace dust. The coke retained in the pellets accelerates the reduction rate. However, at the initial stage of the reduction the pellets become weakened and have to be heated slowly to prevent ring formation. In order to ensure zinc vaporization, pellets should be heated to a temperature of 1100-11500C in the kiln with injection of l ignite fines from the discharge end. Pellets having a degree of metallization of more than 90% and containing less than 0. 1% zinc have been obtained using a test kiln. The final pellet product is intended for use as blast furnace feed. A new plant with a capacity of 20, 000 tonne of dust per month is now under construct- ion and will be in operation next year.

Jan 1, 1974

Alluvial gold mining in New Zealand and in particular on the West Coast underwent a renaissance during the early 1980's. This was based on two main factors: a) the sharp rise in the gold price b) the advent of the hydraulic excavator with which to mine the auriferous gravels. The scale of operations varies considerably. A small operation typically consisting of one or two people using an excavator to feed either a land based or pontoon mounted (floating) gold recovery unit, which will typically feature a rotary screen with or without a tailings stacker with the screened fines < 10 - 15 mm) fed over riflle tables. The largest screening plants of this type are operated by DML Resources in their Arahura and Mikonui mining operations where the plants have the capacity to screen up to 250 m3 of gravel per hour. These plants usually employ jigs and centrifugal concentrators for gold recovery. Unique amongst current operations is the Grey River Dredge, a bucket ladder dredge capable of processing 700 m3 per hour similar to those that operated earlier this century. Gold concentration is by a series of jigs. The number of plants operating in recent times peaked at around 130 in 1987 (coinciding with a nominal average gold price of $751) and since that time has steadily declined to 80 units in 1993 and about 45 - 50 units today. This cycle of rapid expansion and then steady decline has been repeated on the West Coast since the original gold discoveries in the mid nineteenth century.

Jan 1, 1996

By J F. C L Costa, J C. Koppe, C Diedrich

Currently mineral resources evaluation is firstly expressed in terms of volume. Next the resources are transformed into tonnes by using an average bulk density applied to the whole deposit or, in some other circumstances, various different densities to distinct geological domains. Previous work in uranium, copper and nickel deposits used linear correlation between grades and bulk density to derive the density. Geophysics methods are also another good way to obtain density indirectly.These approaches do not take into account that two samples with the same grade but with different bulk densities can characterise different sample supports, leading to severe bias in grade and tonne estimates. It is important that the systematic measurements of bulk density are included into the estimation process, particularly when density is not correlated with the grades. Additionally, the extra time and costs involved in obtaining the bulk density data have made the mining industry disregard it.This study reports the impact in resource estimates by using a methodology that includes the bulk density variability. It involves the determination of a variability model for the bulk density and another model for the composite that was weighted by density as well as by its length. Next, these variables are estimated by kriging and the final grade estimates are obtained. The tonnages are obtained with the bulk density estimates. The conventional methodology was also applied and both estimates are compared to the reconciliation data from a major copper deposit. The results show a significant difference between the tonnage and grade estimates obtained from these two methodologies.The results show that considering density variability when compositing leads to a more accurate methodology resulting in better grade and tonnage estimates locally and globally.

Sep 26, 2011

Willyamite from the type locality, Consols mine, Broken Hill, N.S.W., has been re-examined, and found to consist of zones with widely different Co:Ni ratios. The name willyamite is redefined to include the portion of the (Co, Ni)SbS series with cobalt in excess of nickel. Willyamite is pseudo-cubic, with the three axes equal to within 0·001 A.

Jan 1, 1970

By Zamel GI

The utilisation of fossil fuels, including coal (of which Australia is a large producer and exporter) is a significant contributor to the emission of greenhouse gases. Methane gas, formed during the coalification process, is present in coal seams to varying levels depending on the rank and depth of the deposit. This gas usually escapes to the atmosphere during mining operations without prior conversion to C02 or utilisation as fuel. The quantity of methane released can represent from less than one percent to more than five percent of the carbon content of the coal mined. Per unit of carbon, methane has a greenhouse impact many times that of C02. The emission of uncombusted methane to the atmosphere can therefore represent a greenhouse impact of similar porportions to that of the CO2 formed by combusting the mined coal. However, greenhouse emissions from coal can be minimised by collecting the coal seam methane and converting it to water vapour and the less damaging form, CO2. If such conversion is carried out while performing useful work, the methane can further reduce greenhouse emissions by displacing other fossil fuels. Technology has been developed to allow coal seam methane gas to be economically collected in a pure form, uncontaminated with air. This pure methane can be used to supplement natural gas supplies, to generate power or for the production of chemicals or substitute transport fuels. By collecting and utilising coal seam methane, the greenhouse impact from the mining and use of coal can be minimised, with significant reductions possible in the case of gassy deposits.

Jan 1, 1989

The Ediacara mineral field is classified as a Mississippi Valley type deposit with stratiform mineralization near the base of the Cambrian beds. Mineral deposition was contemporaneous with sedmentation and reerystallization, and mobilization took place after lithification of the sediments. Several mechanisms of deposition were possible.INTRODUCTIONThe Ediacara mineral field is located in the Mt. James Range approximately 300 miles north of Adelaide, about 12 miles west of Beltana railway siding and 10 miles east of Lake Torrens. It is isolated geographically from similar deposits of equivalent age and environment in the Flinders Range Province (Fig. 1). The climate may be described as semi arid with high summer temperatures and frequent dust storms. Occasional thunder storms are the main source of rain in the summer months.The exact date of discovery is unknown, but is believed to be about middle of the last century. Ulrich (1872) was the first geologist to report on the field. At that time only the southern portion of the field had been prospected (and abandoned). Although the prospects did not appear encouraging Ulrich advised prospecting of the shales and testing beneath the limestone.In 1888, Rosewarne, an Inspector of Mines, visited the Southern Workings and queried whether they were connected with some lode at deeper level or were merely bedded deposits. The first geological map with sections was drawn by H.Y.L. Brown (Brown 1892).Brown recognized three principal rock formations as dolomitic sandstone, kaolinised shales and sandstone, and quartzites and sandstone in descending order. These three basic units are still recognized. He recognized also the stratiform nature of the mineralization in the shales as a...

Jan 1, 1963

By Falbo A, Quarestima S, Cozza C, Barbaro M

A new synthetic reagent of the mercaptobenzoxazole class, 5- methyl-2-mercaptobenzoxazole, has been studied. This reagent exhibits powerful selective collecting action towards copper sulphides present in several complex ores, as demonstrated both by laboratory and pilot plant tests. Industrial production is expected to start in the near future. The way this reagent reacts with pure chalcocite has been studied utilising in situ FTIR techniques, adsorption tests, electrokinetic potential measurements and Hallimond cell flotation tests. The FTIR studies have indicated the nature of the surface phase. Adsorption isotherms obtained by the rest method have revealed the quantitative evolution of surface products, permitting the determination of surface coverage at various reagent concentrations. The electrokinetic potential has been utilised to verify the stability of individual species in diverse concentration ranges. Correlation of the results obtained has provided indications on the chemical interaction of this reagent with the surface and on the surface Arrangement.

Jan 1, 1993