Search Documents

By Tonkin D. A

Poor performance in the several stages of the magnetite recovery circuit, coupled with poor desliming through inefficient and over- loaded desliming screens, led to excessive magnetite consumption. An accurate and reliable sampling programme was established covering all outlets of the plant. Emphasis was placed on frequency of increments in an endeavour to detect extreme conditions of short duration. Systematic checking of the entry points to these outlets than identified those sections of the recovery circuit at fault, namely magnetite recovery separators and the heavy media cyclone product rinsing screens. More product rinsing water was provided, and modifications to the rinsing screens improved the efficiency of these units. Consistency of operation through automatic control of level eliminated the sudden massive losses in the magnetic separators. Load on the recovery circuit was then reduced by improvements to the raw coal desliming screens. A 50 per cent reduction in magnetite consumption was achieved.

Jan 1, 1974

By L Clarke, R N. Campbell, F Bourke, J Anderson

Lithological units have been classified geotechnically with mechanical tests and discontinuity measurements from the GRD Macraes Limited, Macraes Gold Project and Rotowaro coal mine open pits, New Zealand. Using these measurements slope stability probability classifications (SSPC) have been quantified based on an adaption of Hack's (1998) SSPC system which places less influence on rock quality designation and unconfined compressive strength than previous slope/rock mass rating systems. The Hack weathering susceptibility rating has been modified by using the chemical index of alteration values from XRF major element analysis. Slaking and weathering is an important parameter in slope stability in the Waikato Coal Measures and Otago schist lithologies and hence a non-subjective method of assessing slaking/weathering in relation to the chemical index of alteration has been introduced. Other major components of this adapted SSPC system are the inclusion of rock moisture content and rock strength anisotropy effects on slope stability. This paper explains the systematic approach of using the adapted SSPC system to classify slope stability probability. The main modifications of Hack's SSPC system are the introduction of rock intact strength derived from Mohr-Coulomb failure criteria which has been adapted for varying moisture content, weathering state and confining pressure. It is suggested that the subjectivity in assessing intact rock strength within broad bands in the initial SSPC system is a major weakness of the initial system. Initial comparison of rock mass friction angles, cohesion and strengths derived from the adapted SSPC are compared with results derived from modified Hoek-Brown criteria, MRMR and SMR classification systems. The advantage of the modified SSPC system is that slope stability probability, maximum batter and overall slope height and overall slope angle for open pit walls can be predicted in addition to orientation dependent and orientation independent stability. Examples are provided, using the modified SSPC system to predict initial optimum pit slope designs in proposed greenfield mine sites.

Jan 1, 2000

By L Lorenzen, H Muller

"Every year a large number of projects are evaluated by small listed and unlisted mining companies that are hoping to find the ideal project, which will catapult them from a mining junior status to that of a mid-tier mining company. Usually this includes finding the æidealÆ or ærightÆ orebody and then developing a process which will allow cost-effective recovery of the valuable metals and the production of a saleable product. These dreams are seldom realised and there are a number of good and obvious reasons for this. Issues that are generally high up on the agenda for the smaller companies are: cost of developing a project before the feasibility study stage finding a suitable, or optimum processing technology financing of the project dealing with risk.The most expensive part of the development process for the small miner is often the exploration side of the business and finding the æidealÆ orebody. However, finding the right orebody will not be discussed in this paper. The æidealÆ orebody does not necessarily solve the problems of the mining junior, as much of the uncertainty lies in the process required to recover and produce the final metal product. Once a mineralised deposit has been identified and the grade at least reasonably qualified, the development of a suitable process becomes the driver to convert the deposit into an orebody. This paper proposes that a small exploration company has a very limited opportunity to succeed if it does not do sufficient homework before it identifies the æidealÆ orebody. The risk profile for the small mining company, by its very nature, has to be different to that of a major company and as a result the opportunities often lie in managing different and often new process options, which may be the key to bring such projects on line successfully.CITATION:Muller, H and Lorenzen, L, 2012. Project selection and process development for mining juniors, in Proceedings Project Evaluation 2012, pp 149-158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By L Q. Amorim

The mining district of the Quadrilátero Ferrífero (QF) in southeastern Brazil contributes to 70 per cent of the Brazilian iron ore production, which reached 370 Mt in 2010. Traditionally, four iron ore types were mined in the QF region:1. soft haematite,2. hard haematite,3. friable ‘itabirite’ (the Brazilian name for metamorphosed banded iron formation), and4. canga (an indurated iron-rich crust).With the exception of the hard haematite, these categories derive from supergene enrichment of the Paleoproterozoic Cauê Itabirite. High current iron ore demand means that the QF high grade supergene ores will be depleted in a few decades. Consequently, several mining projects are being developed to exploit unenriched, fresh itabirite. Among them, the Mineração Usiminas Serra Azul project in northwestern QF is one of the most advanced. Four major itabirite types occur in the QF region:1. siliceous (or standard),2. dolomitic,3. amphibolitic, and4. magnetitic.The dominant type in Serra Azul region is a fresh siliceous itabirite, composed essentially of haematite, martite and quartz that averages 36 per cent Fe (51.5 per cent Fe2O3) and 47 per cent SiO2. The second type, the magnetitic itabirite, consisting of magnetite, martite, gruneritecummingtonite, quartz, dolomite, stilpnomelane, and subordinate haematite, is typically a strongly magnetic greenish banded iron formation with the iron grade varying between 25 and 35 per cent. Chemically, it differs from the siliceous itabirite due to the relatively high CaO, MgO and, consequently, high LOI contents. Together with supergene ores, fresh itabirites have been included in the ore reserves of the Serra Azul project. We anticipate that all the four types of fresh itabirite will be incorporated as ore in the QF region, causing a huge increase on the iron ore resources of the district, and representing enormous environmental and technological challenges for the local iron ore industry.

Jul 11, 2011

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

Variety among deserts is nearly as great as among other climatic environments. Common to most deserts, and to areas downwind from them, is the dominance of aeolian transport of surface material, at least during some seasons of the year. The result is dilution of local surface materials with varying proportions of chemically uniform fine sand and silt, often imported by the wind from remote areas. Fortunately, desert pavement,.even though separated from bedrock by a meter or more of nearly pure loess, is simply a diluted reflection of nearby bedrock. Infiltration of loess through the surface debris and the rudimentary soil-forming processes in the desert usually preserve the integrity of the pavement. This pavement, or its "downstream" derivatives, provides a suitable sample for exploration geochemistry if proper care is taken to circumvent the aeolian dilution. The simplest and most commonly used method of circumventing the dilution is to use a coarse fraction of soils or stream sediments, discarding or retaining the finer fraction depending upon the magnitude of the dilution. Where the coarse surface debris is composed of rock chips representative of the bedrock sources, the method is successful. Under most circumstances the coarse fraction of the surface material will give a fair representation of gross lithology and will occasionally give an indication of mineral- ization. The major drawback to this approach is that selective weathering and erosion in the vicinity of mineral deposits often lead to the loss of ore minerals into the finer fraction, leaving a coarse residue enriched in feldspar and particularly in quartz; thus, the geochemical signature from a mineral deposit is effectively reduced or completely masked. The second most commonly used method to overcome aeolian dilution, and probably the most effective at present, is to use a heavy- mineral concentrate. This approach presupposes that the chemical signature sought resides in a heavy mineral. Fortunately, the arid weathering cycle is conducive to the formation of a wide variety of secondary ore

Jan 1, 1988

In addressing the need for non-degree tertiary training, let us examine some recent reviews of engineering and geoscience education. The Finniston Report (1) criticised the formation of engineers in the UK and stated that this was largely due to the narrow British conception of engineering as a branch of applied science which militates against an effective marriage between theory and application. It also criticised the system for not giving students sufficient grounding in the synthesis of technical, human and financial considerations within their undergraduate courses. As we all know, this report has led to the restructuring of engineering education in the UK. More recently, a Review of the Discipline of Engineering was carried out in Australia by a committee chaired by Professor Sir Bruce Williams (2). The report stated that: Australia has a fairly good system of engineering education that should be made better. more should be done to develop the communication skills of both staff and students. more attention should be paid to changes in engineering practice and the human element in technology. there is a serious shortage of state of the art equipment in most engineering schools. female enrolments in engineering courses should be increased from the current level of about 7% to 20% by 1997. employers should develop a better understanding of the need for continuing education. staff in engineering schools should develop closer relations with employers of engineers. higher education institutions with engineering schools should give financial and other inducements to staff to increase the proportion of study leave or professional development leave spent working as engineers in the business sector. there is considerable room for improvements in the teaching process and in the development of evaluation schemes for assessing the teaching contributions of staff. In its recent report to the Council of the Institution of Engineers, Australia, the Task Force on Engineering Education(3) makes the following points: managerial, entrepreneurial, professional and interpersonal skills should be introduced and integrated into the undergraduate courses but studied in depth as part of continuing education. the continuing education policy of the Institution should be promoted and strengthened with all engineers required to pursue continuing education. the Institution should develop a comprehensive guide to continuing education available from universities, colleges and other public and private sector organisations.

Jan 1, 1989

By L Edwards, M Haest, D Mittrup

The focus in the iron ore industry has shifted from increasing production volumes with less regard for cost, to efficient production of quality tonnes. BHP Billiton iron ore geoscience and exploration has embedded infrared spectroscopic sensing of drill hole samples to help meet this challenge.Infrared spectroscopy is delivering mineral predictions that are used for (automated) geology logging and modelling. The spectra are processed together with other available data sets to predict geometallurgical and geotechnical variables that include lump per cent and uniaxial compressive strength.Trials are ongoing to test the benefit of infrared spectroscopy during mining, including the analysis of grade control samples and remote sensing of mine faces. Results show great benefits in the fields of short-term geology modelling, better understanding of material (handling) properties, identification of geotechnical risk areas and high resolution ore-waste delineation.These trials are bringing BHP Billiton iron ore closer to its ultimate goal of having infrared spectroscopic data collected across the mining value chain. Once such data are available everywhere, regression models can be trained at one point (eg iron grade model trained on exploration samples) and be applied elsewhere (eg iron grade predicted on mine faces). Such predictive analytics will enable not only high precision mining, but also provide maximum time to tailor plant design to the ore in the ground, based on learnings from ores processed in other plants. This will improve planning outputs that will eventually increase mining efficiency, processing capability and product quality.CITATION:Haest, M, Mittrup, D and Edwards, L, 2017. Infrared spectroscopy in BHP Billiton iron ore with a focus on in-mine infrared sensing, in Proceedings Iron Ore 2017, pp 549–556 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Since the early 1990s it has been evident that electricity demand has outstripped investment in generation and transmission. At the same time, concerns were being expressed about the risks associated with the run down of the Maui gas field. It is axiomatic that the necessary investments firstly require a stable and supportive regulatory and fiscal environment, and secondly that such investments have long lead times. A unwillingness by successive Governments to fund the necessary infrastructure, however, lead to the profound restructuring of the electricity with the ultimate objective of transferring the investment risk from Government to the private sector. Successive power crises since 1992 result from a failure to put in place a regulatory framework necessary to provide the environment to allow the private sector to make the needed investments within the necessary timeframe. The electricity sector has now stabilised to the extent that the regulatory risks associated with generation investment have been reduced. This does not mean that risk has been eliminated, however, and both economic and environmental issues will continue to constrain investment in some power proposals particularly those in the South Island and especially any South Island coal or gas thermal proposal. This is firstly because of several very simple economic issues:  1. while the South Island may have significant coal resources it lacks a significant electricity market; 2. except for a six to ten week period in a dry year, low cost hydro will price any large-scale South Island thermal out of the market which will restrict any large scale thermal station to a dry year and/or peaking load; 3. except for a six to ten week period in a dry year, export capacity on the HVDC link to the North Island is constrained to around 964 MWe (and 482 MWe from North to South in dry years); and 4. construction of any new thermal plant in the northern half of the North Island will price any South Island thermal station out of the market. There are also significant environmental issues associated with the establishment of a large scale thermally based power station in the South Island. Because the South Island lacks any large scale economically proven gas reserves, the environmental constraints considered are those associated with coal production. A coal mine dedicated to power generation will have significant on-site impacts associated, in particular those associated with disposal of opencast overburden and visual impacts. These will, however, be partially offset by the relative remoteness of such sites to population centres. What cannot be offset, however, is the off-site impacts, in particular, CO2, SOx and NOx emissions, water disposal and acid mine drainage.

Jan 1, 2003

By Turnbull A. G

Thermodynamic calculations based on the ideal system NiO - Fe203 - H2(g) - CO(g) - H2O(g) - CO2(g) show that it is not possible to selectively reduce nickel oxide in the presence of hematite because ferronickel is the zero-valent nickel-containing product. The calculations show that temperature, reducing atmosphere composition and oxide to reductant ratio have a marked effect on the nickel content of the ferronickel alloy and the amount of nickel reporting jn the alloy. The general trends based on the calculations correlltte well with experimental observations.

Jan 1, 1980

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

THE Broken Hill mining field, approximately 31 miles in length, is at present being exploited by seven companies, viz. : North Broken Hill Limited, Junction North Broken Hill No Liability, Broken Hill Proprietary Block 14 Company, Broken Hill ProprietaryCompany Limited, Sulphide Corporation Limited, Broken Hill South Limited, and Zinc Corporation Limited.The variation in size and shape of the ore-bodies in the mines of these companies, together with the many alterations in pitch and dip, necessitates differences in methods of mining, each company working out its problem in its own particular way.In the matter of chute construction for the handling of the ore broken in the stopes, each mine belonging to the above companies has adopted a style particularly its own, though it may be said that one or two of the types approximate very closely to each other, slight minor differences only being noticed in the design. It is the purpose of this paper to give a brief description of the principal types of chutes now in use in th,e various mines on the field, and in doing so they may roughly be classified into three groups, viz:1. Bulk Chutes, 2. Circular Chutes, 3. Square-set Chutes.The Bulk type of chute is used in the North and British mines of the North Broken Hill Limited, the Central and Junction mines of the Sulphide Corporation, the South Blocks mine of the Zinc Corporation, and the Block 14 mine.The Circular type of chute is used by the Broken Hill South mine and the South Blocks mine.The Square-set chute is used in the Proprietary mine, the Junction North mine, and occasionally in other mines where the square set method of mining is a necessity, and more particularly as mullock passes.

Jan 1, 1925

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

By I Douglas, L Allen

Localised indicator kriging was developed following a similar approach used by Marat Abzalov (2006) in his paper titled æLocalised uniform conditioning (LUC): A new approach for direct modelling of small blocksÆ. Abzalov introduced the idea of mapping panel distributions from uniform conditioning onto selective mining unit-sized blocks that were created using ordinary kriging. This concept of remapping panel distributions was applied to multiple indicator kriging histograms.At Newmont a program was developed that made the remapping of MIK histograms to SMU sized blocks extremely efficient and was subsequently tested on several gold deposits. The results have been encouraging as the localised indicator kriging (LIK) method has eliminated many issues that have plagued both ordinary kriging and multiple indicator kriging. Use of localised indicator kriging methodology limits the smearing of high-grade and the over-smoothing of grade that is common and difficult to control in OK but retains the ability for localising grades. LIK also simplifies change-of-support corrections, eliminates un-mineable slivers of low or high-grade when dealing with small tonnages, and allows for the mapping of linear and non-linear estimates into the same block.

Sep 26, 2011

By N Clarke, G R. Ballantyne, M S. Powell, P Elms, A Anyimadu

AngloGold Ashanti Ltd nominated Sunrise Dam Gold Mine as a case study via their involvement with the long-running Australian Mineral Industry Research Association (AMIRA) International P9P research program (AMIRA, 2015) . A group of researchers from the Global Comminution Collaborative (GCC) conducted a comminution circuit survey and review together with a large group of graduate metallurgists, senior metallurgists and operators. Fundamental and applied research understanding was used to identify productivity and efficiency improvements around the crushing and grinding circuits. The limitations of current scientific knowledge were identified through this process and this will allow future research to be more focussed on what is required by industry.The comminution circuit at Sunrise Dam comprises three stages of crushing followed by two stages of ball milling. The secondary crusher and primary ball mill classification were identified as the primary limitations of the circuit. The secondary crusher was found to be underperforming through overall equipment efficiency (OEE) analysis and an improved chamber design was identified by Chalmers University. This improved design will promote higher power utilisation, choke feeding and a finer crushed product for the milling circuit. The primary ball mill product is classified by a combination of a trommel, 3 sieve bends and a hydrocyclone. The combination of poor classification and coarse, competent feed led to a situation where the primary mill was overfilled with rocks, reducing grinding rate due to cushioning of impact. Size specific energy (SSE) benchmarking methodology was used to identify that a 10% increase in throughput could be achieved with improved primary classification.CITATION:Ballantyne, G R, Clarke, N, Elms, P, Anyimadu, A and Powell, M S, 2015. Application of research principles to identify process improvement at Sunrise Dam Gold Mine, in Proceedings MetPlant 2015, pp 221–229 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

The subject which I have chosen for my paper is one that I am sure has occurred to the minds of nearly every mining man on these goldfields at some time or other. I refer to the carrying out of hydraulic mining on a fairly large scale on some ofthe alluvial areas of the West Australian goldfields. There are many, no doubt, who have the question ready at the present moment, "But where is the water coming from? " However, the great difficulties in the way are not due to the want of natural facilities, but due to the fact that sufficiently large areas cannot be leased for this purpose under the present Mining Act. Now, ever since the inception of the West Australian goldfields there has been the old familiar cry when referring to some alluvial gully or flat, "I wish I had a head of water to sluice that ground," but what seems an impossibility at times can be brought to a very great possibility by the use of a little thought and the expenditure of the necessary capital. This is so as regards West Australia with sluicing which, in spite of the its having so many detractors, can be carried out successfully in certain localities if the ordinary facilities on the part of the Govenment are given, and on the other hand the necessary capital is supplied. Alluvial gold areas, I propose now to draw your attention to first of all, the numerous alluvial areas that exist around Coolgardie, Kalgoorlie, Bulong, Kurnalpi and many other centres. Some of these areas have afforded fortunes inthe early days to the alluvial miner, and also afforded a living for years to many diggers' by the use of the dryblowing...

Jan 1, 1901

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980