Search Documents

By D H. Bell

Slab-buckle failures in coal sequences involve thin slab deformation in strata dipping parallel to the footwall, and are a consequence of both unloading and the weak nature of the thinly bedded rock mass. Methods of modelling and predicting such occurrences include: +        a conceptual model using a base friction table, +        a mathematical model using the Euler solution for column and beam bending (after Goodman, 1980), and +        computer analysis techniques such as UDEC (Universal Distinct Element Code after Cundall and Hart, 1993).   Slab-buckle failures have the potential to seriously disrupt production because of their volume and rapidity, and to endanger both equipment and personnel working on the pit floor.   In July 2004 a large slab-buckle failure occurred overnight after a new batter and bench had been formed at the Malvern Hills Opencast Mine in inland Canterbury. This involved the entire length of the pit (85m along strike) when a 2m thick intact slab with a total volume of ~3500m3 translated down dip 6.2m on the base of a thin coal seam to form a pronounced buckle at the toe. The coal measures consist of finely laminated mudrocks with multiple coal seams of varying thickness dipping ~45¦ to the southeast, and the opencast mine had been designed with footwall batters formed parallel to bedding with a vertical bench separation of 15m.   Back analysis of the Malvern Hills failure was necessary to investigate the controls on footwall instability, and for future mine design. An engineering geological model was created and samples of the slab material and failure surface were collected and tested to establish the required parameters for use in the Euler solution for column and beam bending. Back analysis using the Euler solution provided unrealistic results that overestimated the overall length of a stable slope by more than 10 times.   No further large scale slab-buckle failures have developed at the mine site, in part because of the slow rate of coal extraction, but precautionary drainage of the footwall slopes has been undertaken to improve overall batter stability. The location of the slab-buckle failure on a critically positioned pre-sheared thin coal seam with full hydrostatic head is considered the most probable cause of the July 2004 failure, rather than inherent instability of the generic bench and batter arrangement adopted. The use of a precedent-based engineering geology approach to future mine design is considered the most appropriate solution in the circumstances.

Jan 1, 2007

Influence of Frothers on Bubble Shape and Velocity Close to the Generation Point

Sep 13, 2010

By S Kodate, Ö Aydan, Y Suda, J Tomiyama

Fracture zones are commonly found in the Earth’s crust. These zones may cause very severe engineering problems. Therefore, the formation and the assessment of the mechanical characteristics of these zones is of great concern for rock engineers. A new double shearing jig was used to study the formation of shear zones in rock under static and impact loading conditions using the device developed by the authors. A series of experiments were undertaken to investigate formation on the formation and characteristics of fracture zones in laboratory. Although actual fracture zones are more complicated, various tests give some insight view of the formation of fracture zones as well as some information on their mechanical behaviour under both dynamic conditions and static conditions. The authors report the outcomes of these experiments and discuss their implications in practice.

Nov 29, 2022

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

By Cleghorn JH

Underground mining operations on Kalgoorlie's Golden Mile were suspended in 1976, suffering the combined effects of low gold prices and grades. A subsequent substantial increase in the gold price led to the decision by Kalgoorlie Mining Associates to reopen their mines in 1979. The two shafts selected for access required excessive maintenance. The geological assessment and development parameters prescribed have been successfully used to establish reserves to maintain production at a 390 000 tonnes per annum rate. While ore reserve grade is being maintained from primary stoping sources, supplementary lower grade ore is drawn from remnant pillars and stopes at lower cost.Performance by the workforce has reached levels previously attained and a record tonnage was hoisted in the fourth year after recommencement.Keywords : Golden Mile lodes, geological research, payruns, cut and fill, mill holes, gold price, ore grade, amalgamation.

Jan 1, 1984

By J Dwyer, G Turner, D Pridmore, M Urosevic

Due to their ability to produce high-resolution images of the subsurface to great depths, seismic surveys provide critical inputs to almost all oil and gas exploration projects. However, with some notable exceptions, seismic surveys have rarely been used in mineral exploration. In the past, this was due to both technical and financial reasons. Significant developments on both fronts mean that seismic surveys can now offer substantial benefits to mineral exploration and mining, and surveys conducted for exploration can provide important data sets for mine planning over the life of a mining project.We present case history data that show that seismic surveys can greatly assist with mapping the 3D distribution of lithologies and alteration and, in favourable circumstances, directly detect mineralisation in and around mineral systems. As a result of their high spatial sampling density, seismic surveys are also highly effective at mapping structures that can remain undetected or poorly characterised by drilling alone. These structures may host or provide important vectors to mineralisation. They can also be particularly important when planning shafts, raise bores, declines, stopes and open pit walls. A further benefit of seismic surveys is that they can remotely provide information on geotechnical rock parameters that are used for rippability, slope stability, blasting and ground support.CITATION:Turner, G, Urosevic, M, Pridmore, D and Dwyer, J, 2015. Exploration and mining unified through seismic imaging, in Proceedings Third International Future Mining Conference, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By B Bradák, D Asahina, S Saydam, S Akdag

Human exploration of Mars has been on the horizon of scientific goals for decades now, and as part of the objectives of human missions to various planets, one of the possible goals is opening new economic frontiers by the potential extraction and utilisation of resources, eg mining minerals and using surface regolith (Neukart, 2024). A comprehensive understanding of surface morphology, lithostratigraphy, basic structural geology, and civil engineering technology is essential to conduct mining operations for resource extraction on extraterrestrial planets. For instance, proper assessment of the risks associated with excavation and infrastructure construction under unique environments such as low gravity, surface irregularities, and the presence of regolith is fundamental. Such knowledge has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander (Knapmeyer- Edrun et al, 2021; Banerdt et al, 2020; Giardini et al, 2020). Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults exist and form regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. In this study, we focus on so-called graben structures, one of Mars’s common tectonic structures (Plescia, 1991; Banerdt et al, 1992; Hoogenboom Hagen, 2014). The study aims to provide additional information about the tectonic environment during the formation of such features and, in addition, the internal mechanical-rheological structure of Mars, revealed by the geometrical pattern of faults modelled and simulated in a laboratory environment.

Sep 1, 2024

By Hori M, Komatsu T

In Japan, a small-diameter tunnel boring machine (TBM) of diameter 2.6 m applicable to a wide range of geology from hard rock to soft strata was developed with the purpose of reducing construction costs of headrace tunnels for small hydroelectric power stations. And in 1983, a demonstration test was carried out in the No. 1 headrace tunnel work of Hayakido Hydroelectric Power Station. The principal achievements in executing work are the following: (1) Although this TBM was a demonstration test unit, excavation advances averaged more than 200 m/month and exceeded the average 150 m/month with a conventional method. (2) According to PS velocity surveys after tunnel excavation the zone of loosening due to the TBM method was small enough to be ignored and was approximately one-half compared with conventional methods in rock of the same evaluation.

Jan 1, 1987

Cretaceous to Cenozoic sedimentary basins in Western Southland include a wide range of non-marine and marine sediments, in a structurally complex setting dominated by major fault systems. A reassessment of their mineral potential confirms large quantities of nonmetallic minerals (limestone, aggregate, marl), and smaller reserves of bituminous coal, lignite, clays, and oil shale. Hydrocarbon potential is largely untested. Metallic minerals are present in trace amounts, apart from platinum group minerals and some detrital gold. In the offshore area, seismic data suggest the hydrocarbon potential is significant. The Orepuki area has the most interest onshore.

Jan 1, 1992

The results expected from a longwall face can best be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the effective operating hours, and the utilisation.The effective operating hours are determined by a number of scheduling factors which include the proportion of manned time to calendar time, the effective shift factor (effective time to manned time) and the move times.Analysis of the results achieved on the last 121 completed longwall panels in Australia (1984 onwards) shows a significant trend between 'actual tonnes/manned hour' and 'ideal production rate' (the measure of the capacity of the installation).Using 1982 'state of the art' longwall equipment, (the average in use in the seven year period), it should be possible to produce around 2.7M tonne/year ROM from a mine with one longwall. Few mines are achieving this.A review of production scheduling factors and general natural hazards affecting some mines suggests three things.1. Whilst some increase in average effective hours has followed the CIT decision, further improvement is possible at many installations.2. Many mines subject to general natural hazards, such as high gas make and high general stress, have found effective solutions and achieve the same utilisation as the overall average.3. A small number of faces within such mines have been severely affected, some less so. The most severe effects of natural hazards appear to be very site specific. This emphasises the need for detailed investigation of the causes, and development of means of predicting their presence. Only then can either satisfactory technical solutions be found to overcome the problems or prior decisions be chosen not to mine badly affected panels.

Jan 1, 1991

By A Lyon

The minerals industry, as many other industries, has a wealth of indicators and a thriving æindustryÆ in their development, measurement and reporting. It is natural for this to occur for a new endeavour. However, perhaps it is time for the community concerned with minerals industry indicators to ask whether we have achieved a certain maturation whereby proliferation of indicators may be replaced by a more disciplined and constrained approach. In many natural and engineered systems, thermodynamics provides well-understood and tested constraints. Indicators that are uninterpretable in this framework are not considered acceptable. This paper provides initial evidence that such a formalism may be possible for mine sustainability. The formalism developed does not claim to have the rigour of thermodynamics. However, it does provide a first step towards formalising selection of indicators on the basis of their true comprehensibility. A set of simple equations is developed that represent the conventional five capitals (actually we use six because we separate renewable and non-renewable natural capital) and how they are linked. This is coded into a simulation model. The base equations are then used to develop a system level indicator of sustainability performance, which is asserted to be a reflection of the mineÆs reputation. We define a least sustainable state, termed æmaximum revenue mining (MRM)Æ in the system and define the degree of system sustainability as how far the system is from the MRM. We then introduce a simple mechanism whereby different actors can express differing views on the emphasis for the distance from MRM. Sustainability thereby becomes a non-unique thing that is defined by a distance from MRM and a set of preferences across the capitals.

Jan 1, 2009

By R G. Barker

The NZ Minerals Industry Association has continued to advance the interests of the minerals sector through leading the establishment of a Minerals Industry Advisory Committee, and the preparation of a technology strategy with funding assistance from the Foundation for Research, Science and Technology. The current moves mirror those of more than 30 years ago when a government initiative led to a resurgence of exploration through amending the mining legislation, redirecting Government research priorities and tax changes. The economic and political and commercial environment in 2001 is very different from that of the 1960s and success of these new initiatives depends on the continuing support and involvement of all sectors of the minerals industry, and building an improved relationship with the Government and the public.

Jan 1, 2001

By R A. Pakhomov, L V. Krupnov, P V. Malakhov, I M. Dymov

The article presents results of thermodynamic calculations and laboratory studies, focusing on the cobalt behaviour during oxidative smelting of copper-nickel mattes. The compositions of the studied solutions are related to the products formed during the second stage of the converting process of copper-nickel matte at the Nadezhdinsky Metallurgical Plant (NMP) of MMC Norilsk Nickel company. These sulfide products typically contain from 1.5 to 12 wt per cent of iron. The obtained experimental results and thermodynamic calculations indicate that adjusting the CaO ratio to increase the proportion of CaO or complete replacement of SiO2 with fluxes containing CaO leads to a significant increase in cobalt recovery rates in the matte phase (with an iron concentration of 2.5 wt per cent) raising them from 30 per cent to 45 per cent. Meanwhile, the recovery rates of copper and nickel remain constant.

Aug 21, 2024

Australian rutile and zircon concentrates are refined raw materials and not manufactured products. The composition and properties of the grains are therefore fixed by nature. Specifications and assay certificates should take this into account by eliminating unnecessary provisions which only increase the time and cost of analysis.INTRODUCTIONThe raw material from which Australian rutile and zircon concentrates are isolated is beach sand on the coast of New South Wales and Southern Queensland. The principal current operations are in an area between Sydney and Brisbane.The sands consist principally of quartz particles, but they contain from 1 per cent to 50 per cent of a mixture of heavy minerals, including zircon, rutile, ilmenite, monazite, leucoxenic grains, chrome spinel, chromite, garnets, corundum, topaz, brown spinel, olivine, epidote, clinozoisite, tourmaline, magnetite, hematite, and cassiterite. The major components are zircon (25 to 60 per cent), rutile (25 to 50 per cent), and ilmenite (5 to 50 per cent).The so-called leucoxenic grains are not a definite mineral species but an alteration product of which the major components are titanium oxides and silica in varying proportions.Primary concentration is by gravity, using spirals or various forms of pinched sluice (Pullar, 1962), the resulting concentrates being redressed on wet tables. During these processes, some of the lighter heavy minerals including leucoxene and impure rutile, which tend to degrade the final rutile and zircon concentrates, are eliminated.The separation of heavy minerals from each other is...

Jan 1, 1963

By Voorhees JS, Bureau G

To operate a mine in California requires compliance with State environmental regulations, including assessment of risks and associated financial assurances for postulated worst case catastrophic event scenarios. Carson Hill Gold Mine, an open pit, heap leach operation, completed new risk assessment catastrophic event analyses in 1988. The risk assessment was performed at the same time that a new leach site (Leach Site 3) was being designed. Leach Site 3 is located about 400 m upslope of New Melones Reservoir, which is a public recreation facility and a source of drinking water. Release of leachate (pregnant solution) or ore containing cyanide and metals from Leach Site 3 into New Melones Reservoir was considered to pose the largest risk of environmental damage.Flow failure of the ore heap, potentially induced as a result of liquefaction of the saturated portion of the ore, and/or overtopping of the leach site containment embankment due to excessive precipitation were found to be the most plausible leachate release scenarios. Yearly combined probabilities of various downstream release volumes were estimated. The release volume corresponding to a yearly probability of 0.05 percent was then used to estimate potential environmental impacts and mitigation costs. The costs include earthwork to restore the geometry of the ore heap and repair the fill slope below the Leach Site 3 containment, and impacts on New Melones Reservoir.

Jan 1, 1990

Asian countries are now facing very crucial aspects of urban living under the recession of the economy. The current situation is such that those hard aspects may make the living standards worse and worse in the next century, unless proper measures are taken on the infrastructure for urban lives. More than half of the population in Asian countries are now living in cities. Nowadays, the socio-economic development of the Asian countries has been closely linked to the development of world economy because of the border-less economy system. The population inflow to big cities is inevitable as the Asian countries step into an industrialised economy. Such a tendency will be further accelerated when Asia becomes a centre of financial business in the 21st century. The government of any country has realised the situation very well. The United Nations has established a specific agency to solve the problems caused by the rapid urbanisation. This global agency for urbanisation is named United Nations Center for Human Settlement and it is so called Habitat. There are three Habitat offices in the world, Nairobi in Kenya, Santiago in Chile and Fukuoka in Japan. The activities of Habitat offices cover a wide field of issues such as housing, urban development, infrastructure and environment, etc. Habitat Fukuoka Office is serving Asia and Pacific in co-operation with the government offices concerned.

Jan 1, 1999

By T Gill, A Faragher, B Scott, V Kakebeeke

In 2000, after six year intensive exploration for high-grade haematite deposits, Rio Tinto included the channel iron deposits (CID) as a specific iron ore target in the Hamersley Province iron ore exploration program. The exploration model was simple and based on the then current understanding of CID genesis. Fundamental to the model was an interpretation that CID deposits after their final accumulation stage could be entirely concealed in their channels. Inversion to mesas and therefore exposure of the CID profile would only occur in areas where the modern drainages follow the ancient and have significantly incised their current bedrock. The model took encouragement from observations at Bungaroo Creek, where large CID accumulations occur in a deep valley incised in the Wittenoom Formation concealed below recent valley fills derived from the surrounding BIFs. Also, in the headwaters of the Yandicoogina system CID occurs below a more recent cover of calcrete and clay. After a number of failed or partially successful attempts, exploratory drilling in 2002 in the Caliwingina valley in the northern Hamersley Range identified significant CID mineralisation. Subsequent drilling programs from 2003 onwards revealed the presence of a large CID system, which stretches from the middle reaches of the Caliwingina Creek to deep under the sediments of the Fortescue Valley, a channel length of more than 30 km. Although the drilling is still somewhat sparse, the geological resource estimation suggests that Caliwingina is presently the third biggest CID system of the Pilbara (after Yandicoogina and Bungaroo Creek) and is of comparable size to the premining Robe River system (1.6 Bt), with comparable Fe-grades to the Yandicoogina global resource grade (57.7 per cent Fe). Large detrital and canga deposits overlie the Caliwingina CID, or interfinger with it, and although the economics of these are presently unfavorable, could ultimately present a low-grade iron resource of slightly smaller size to the CID mineralisation at Caliwingina Creek. Together with the recently discovered Serenity and Solomon deposits, as well as Cabbage Gum Bore and other smaller occurrences, the Caliwingina Creek deposit is part of a major new CID district in the central Hamersley Ranges, approximately halfway between Yandicoogina and Robe River. Although exploration in this new district is still underway, the preliminary indications are that this area will provide a total CID resource well over 3 Bt, and is on a par with the major known CID systems in the Hamersley Province.

Jan 1, 2009

By M E. Webb

Safety is a key value in most leading mining companies. Despite years of effort, and significant expense in ‘programs’, operating sites seem to have been left with no real improvement in either the elimination of fatalities or sustained reduction in injuries.Safety systems and processes have grown and evolved, often to the point where they have become overly complicated and marginally useful.MMG Limited, following the consolidation of its Australian operations under a single management structure, undertook a program to effect real and sustained change in its approach to managing safety. The program aimed at improving safety by better engaging its workforce and by making safety processes simple, useful and effective. It defined the role of the supervisor in creating safe work, the role of the people doing work and the role of safe work methods.A safety diagnostic tool was developed to assess site against safety-critical mindsets, behaviours, cultures and systems. The outcome of the diagnostic is considered by the organisation to be the true lead indicator of safety performance.While still a work-in-progress, the program at the Australian Operations of MMG Limited shows that challenging common paradigms in safety management can create real change in safety performance.CITATION:Webb, M E, 2016. Making safety simple, useful and effective, in Proceedings International Mine Management Conference, pp 217-223 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996