Search Documents

By McHaina D. M, Hardcastle S. G

A description is given of an investigation into the feasibility of using controlled recirculation of warm exhaust air into the cold intake air of underground mines during winter. Canadian mines can experience inlet air temperatures of minus 30 ¦C and less, requiring them to pre-heat their intake air. The use of controlled recirculation would reduce the inlet air quantity and thus reduce heating costs which exceed $1M on some mines.

Jan 1, 1988

By J de Witte

When used in suitable ground conditions, rock bolts can have advantages over other permanent tunnel lining solutions. Permanent rock bolts offer flexibility in tunnelling profile and rapid rock bolt installation can enable time and cost savings. There are also disadvantages when considering the suitability of rock bolts for permanent support installations. These generally concern achieving the specified durability requirement over the specified design life. By investigating alternate approaches to rock bolt installation, quality assurance (QA), monitoring and design life it may be possible to alleviate some of these concerns.The design and construction benefits that can be realised through the use of rock bolts are primarily related to reducing project program time. This time reduction could be realised if rock bolts are considered as a permanent solution, with the installation being completed as a part of the primary excavation cycle. Any reduction of the program could allow direct and indirect cost savings and in the case of a major project, allow the revenue stream to be realised earlier.Currently ambiguity exists where the treatment of rock bolts as permanent support components is inconsistent with that of (often identical) ground anchors, as utilised in stabilising cut and cover structures. The ground support design process, implementation and testing are generally similar, though the acceptance of rock bolts as long-term support elements is treated differently to ground anchors in technical specifications.This paper discusses some of the benefits available through the use of rock bolts. It offers different solutions to the concerns surrounding durability, including alternate approaches to installation, Quality Assurance practices and monitoring solutions. The selection of an alternate design life is also investigated as another means of alleviating concerns around long-term durability. The paper will also provide an indication of savings that could be expected through the use of rock bolts as part of a long-term support system.

Mar 8, 2011

By M Rauer

With a worldwide growing population the demand for higher living standards, food and the development of new technology is rapidly rising. To allow for a continuous growth, larger quantities of minerals and raw materials are needed at a faster pace. Different methods have been developed to access or tap ore more quickly, such as improved drill and blast operations, mechanical mining methods using equipment such as roadheaders (RH), longwall miners and other technical equipment. Another possibility to access and develop mines faster is the use of a tunnel boring machine (TBM).The historical usage of TBMs is surprisingly long, but the opportunity for technology adoption by the majority of worldwide mining companies remains largely untapped. Dozens of full face TBMs have been used by mines around the world, including two that will begin operation soon in Australia. TBMs have been used to safely and rapidly gain access to the orebody, or to expand access to the orebody to increase output by running a TBM along the edge of the orebody for several kilometres. These machines have also been used for ventilation and for conveyor tunnels for ore removal. They have been used to quickly excavate long and winding declines giving access to an orebody at several levels in a short period of time.Tunnel boring technology can be used for mine declines, mine access tunnels and all sorts of different mine designs and set-ups. TBM technology simply needs to be adapted to the mine conditions and, if manufacturers are involved early on in the planning process for mine development, the operation can be very successful. In some cases, historically typical mine designs may need to be re-thought.One mine, the Stillwater Platinum mine in Nye, Montana, is currently employing its fourth TBM in 25 years. Two were used to create tunnels running alongside the orebody, rapidly expanding access to the orebody in many locations for increased output. Two were used to create parallel access tunnels to a mine expansion at the East Boulder orebody; one tunnel is for conveyor haulage and the other for vehicular access. TBMs have been employed successfully many times to rapidly drive vehicular decline tunnels to multiple mine levels, such as at the San Manuel – Magma Copper mine in the USA. While TBM technology may not seem to be optimal for every mine, these success stories show that the method can provide vast benefits for the right projects.Early use of TBMs in extremely hard rock metal mines, in the 1960s and 1970s, had limited success since performance was low. However there have been great improvements made over the years in the strength of rock which can be excavated by TBMs with high performance. Other important improvements involve the provision of a safe work environment, safely and rapidly supporting the rock and predicting geology ahead of the TBM.This paper will briefly note the more than 20 TBM mining projects and highlight some notable successes. It will then go on to give a status report on the two active TBM mining projects in Australia and the difference between a TBM operation versus other excavation methods such as drill and blast (D&B) or RH excavation.CITATION:Rauer, M, 2014. Tunnel boring machines in mines – a?brief review of past use with a status report on use today in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 663–670 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Mather

Fibre reinforced shotcrete has long been accepted as temporary ground support in both mining and civil tunnel linings. Greater knowledge and understanding of shotcrete as an engineering material and advances in its quality have enabled designers to eliminate the requirement of a second pass lining. The initial shotcrete can be used as the permanent tunnel lining or be incorporated into the final lining design, rather than ignored and considered as sacrificial.For the initial shotcrete lining to become a suitable permanent tunnel lining it must be able to establish and maintain stability over time when subjected to all possible loads. To ensure this, best engineering practices are required during the design phase of the project to analyse; ground conditions including rock mass properties, ground and ground water quality, rock mass loadings, excavation sequencing, and construction methodologies.The increased durability of steel fibre reinforced shotcrete over traditional tunnel support, in the right ground conditions, makes it possible to achieve a serviceability design life of greater than 100 years (as required in most infrastructure projects). By specifying a good quality shotcrete mix and ensuring adequate quality control for batching, fibre dosing, preproduction testing, excavation sequencing, and application control, it is possible to eliminate the requirement of a secondary lining. The properties of a suitable permanent lining must be well established using suffi cient preproduction testing in combination with post application monitoring.A major benefit of steel fibre reinforced shotcrete in ground support applications is the removal of any requirement for workers to work under unsupported ground. Its use can also significantly reduce, if not eliminate, the manual handling associated with placing traditional reinforcement such as lattice girders and mesh. Both of these benefi ts are significant with the ever increasing focus on health and safety.This paper highlights factors that must be considered in the design and specifications to enable an initial shotcrete tunnel lining to become the permanent shotcrete tunnel lining.

Mar 8, 2011

By M A. Noppé

Mining is inherently a risk-based business and risk governance is an integral part of corporate assurance and business decision-making. Mineral Resources and Ore Reserves are the key assets for a minerals company and senior management/company boards require assurance regarding the likely accuracy of estimated and reported technical information. Reviews and audits improve the level of assurance in the reliability of estimated short-term (grade control) estimates, reconciliation, Mineral Resources and Ore Reserves.Peer reviews and audits contribute not only to governance processes, but also provide valuable technical improvement opportunities, as well as mentoring and professional development guidance to those whose work is being reviewed. Technical review is particularly crucial at a time in the industry when companies are running lean or perhaps inexperienced teams, with limited technical or management oversight.Despite both industry guidance and some companies’ standards expecting or requiring reviews and/or audits of Mineral Resource and Ore Reserve generation and reporting processes, it is surprising how infrequently or ineffectively these are actually carried out. Examples of governance systems are presented, which include appropriate peer review processes that if effectively applied, can identify shortcomings in technical processes and provide timely correction to prevent, or mitigate against, erroneous outcomes.Peer reviews are ideally carried out concurrently with the preparation of data, selection of estimation procedures and validation of outputs from Mineral Resource and Ore Reserve estimation prior to the handover of results between disciplines, or the final reporting of results. Audits, on the other hand, are generally retrospective reviews by independent and/or external reviewers who rate the risks inherent with an already completed process, identifying opportunities for improvements in the future.This paper outlines the main components of peer reviews and audits, discussing how a combination of these can provide a structured and objective assurance system leading to systematic and disciplined processes to improve the effectiveness of, and confidence in, grade control, reconciliation, Mineral Resource and Ore Reserve risk management, and support good governance.CITATION:Noppé, M A, 2017. Improved assurance for Mineral Resource and Ore Reserve estimates and reporting through peer review and auditing, in Proceedings Tenth International Mining Geology Conference 2017, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R Winterberg

Concrete is a well established and reliable construction material for the permanent lining of tunnels, but shows some weak performance characteristics, which can be overcome by the addition of specialised fibre reinforcement. This paper addresses the particular performance design requirements of segmental linings, discussing the improvements of fi bres on concrete properties. Focus is made on the beneficial effects of fibre reinforcement on the cracking behaviour and the toughness performance, providing a safe and durable tunnel lining.Not only the mechanical performance of fibre reinforced concrete (FRC) for segmental linings, but also the durability of the linings has gained growing attention among the designers and consultants. Especially tunnel linings with exposure to media with corrosion potential, such as wastewater sewer tunnels or desalination plant outfall tunnels, have high requirements on their durability. The design of these structures must provide a comprehensive study of durability aspects. Fibre reinforcement can substantially improve the durability of concrete.Research has been carried out on the cracking behaviour of concrete. The beneficial effects of steel fibres on the cracking behaviour reduce the permeability by reducing the flow paths within the concrete. Crack bridging steel fibres create necking effects in bending cracks, leading to earlier closure of the cracks. Further, steel fibres create particular crack formations, which lead to a substantial reduction of the fl ow rates through separation cracks. The results also show that considerable cost savings can be achieved using FRC, as the thickness of the linings can be reduced.The durability design issues will be addressed and underlined by a case history on the Hobson Bay sewer tunnel in Auckland, New Zealand.

Mar 8, 2011

By T O&apos, Sullivan

Reconciliation of metal production from a sublevel cave (SLC) mining operation is a complicated process. SLC reconciliation is unlike reconciliation for open stope operations, where a tonnage of extracted ore can be assigned to an exact volume of in situ ore, and a direct comparison made between the estimation of contained metal and actual metal production. In SLC operations the ore extracted from a particular SLC drawpoint will be composed in part from the parcel of freshly blasted in situ material, in part from varying components of ore material (from cave stocks) flowing down from other previously mined areas vertically above the current draw position and in part from external dilution. This leads to difficulties in reconciling production grades against estimated grades. The problem is that we know how much metal we have produced but we can not precisely say where it has come from. Metal production reconciliation is fundamental in assessing ore reserve estimation accuracy and performance and in determining a draw management strategy for SLC mining. In terms of contained metal, differences in extracted metal compared to in situ metal represent changes to cave stocks. To generate local estimates of the cave stocks, differences in metal for each ring are treated as additions to or subtractions from a series of vertical columns of stocks extending throughout the height of the cave. The sum of metal differences (extracted versus in situ) for each vertical column results in a residual metal map at any particular mining level. The metal maps show areas where the metal production has been greater than or less than expected. The maps also highlight areas in the cave where residual metal is located, areas where targeted overdraw can reduce cave stocks.

Jan 1, 2006

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009

By C Xuan, J H. Park, Q Wang, C Shen, D Kumar, W Mu

Dissolution of non-metallic inclusions in the metallurgical slag is of vital importance for cleanliness control of the steel manufacturing. With the development of high temperature confocal laser scanning microscope (HT-CLSM), new insights have been obtained due to its in situ observation characteristics, higher resolution and precise control. However, HT-CLSM measurement has the limitation, eg the slag composition cannot include high amount of transition metal oxides. In addition, it is time consuming for the experimental procedure and not so simple to succeed for every measurement. It is known that digitalisation has made a significant progress in recent years. Machine learning (ML), a sub-domain of artificial intelligence (AI), is the key enabling technology for the digitalisation of the material science and industry. The database for ML model is collected using almost all available HT-CLSM experimental data and subsequently the established database is trained by different ML methods. Unseen data is used as the benchmark of the ML model. Al2O3 dissolution is the main process to be predicted in the current study. A good agreement between the HT-CLSM data and the ML model prediction results show the possibility to apply ML in process metallurgy.

Jun 19, 2024

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By R Castedo, P Segarra, I del Castillo, L M. López, J A. Sanchidrián

This work investigates some suggested methods for blast vibration monitoring on a hard surface based on 53 tests on a vibration exciter. Errors in the measurement attributable to coupling have been described as function of frequency by the rock-to-mount (or coupling) transmissibility, ie ratio of the velocity of the vibration sensor mount to the velocity of the rock motion. Transmissibility has been measured from 2 to 200 Hz, at two vibration levels (5 and 20 mm/s), in four seismographs. Attachment methods with an anchor, thermal adhesive and gypsum plaster allow stiff rock-to-mount coupling. They ensure accurate measurements (errors below 0.3 dB) for frequencies commonly found in blasting (below 100 Hz) irrespective of the mount characteristics and the vibration level. Free laid mounts and sandbagged vibration sensors lead generally to a poor, weak coupling. Errors are non-linear errors with the input velocity, ie the operating frequency window narrows as the velocity of the ground increases. Free mounts follow ground motion acceptably well (error up to 0.4 dB) at both vibration levels and frequencies below 15 Hz. At higher frequencies, free mounts lead to the largest distortions with expected errors ranging from 0.8 to 6.6 dB. Sandbagging limits the expected errors below 1.3 dB, but it does not prevent large errors that can be up to 4.5 dB. Both frequency and velocity should be considered together to assess the measurement errors instead of the expected accelerations, as it is currently made.CITATION:Segarra, P, Sanchidrián, J A, Castedo, R, López, L M and del Castillo, I, 2015. Effect of vibration sensor mounting method on the quality of vibration measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 545–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The refractory nature of residual gold in Kalgoorlie calcines is caused by occlusion in dense pyrrhotite formed by fusion within pyrite grains during decomposition. Fusion of pyrite increases as the rate of heating exceeds the rate of sulphur expulsion. By controlling these rates in relation to each other in a fluidised system fusion is limited and an expanded structure is formed. The increased area presented to cyanide solution, and the decreased diffusion distance, makes gold more accessible for extraction. Gold extraction from expanded pyrrhotite, before oxidation for porosity, is comparable with extraction from fully oxidised calcines from Edwards roasters. A method is suggested for standardised comparison of cyanidation residues.

Jan 1, 1957

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By N Bezuidenhout

The performances of ten field-scale experimental final covers were evaluated over an eight-year period. The covers were evaluated as part of the rehabilitation of acid generating coarse coal reject dumps and opencast coalmines in the Northern KwaZulu Natal province in South Africa. The main purpose of the experimental covers was to restrict rainfall infiltration into acid generating coal discard. The mean average rainfall over the monitoring period was 839 mm with 84 per cent occurring between October and April. The average evaporation was 2100 mm. The site is described as a ædry siteÆ since the evaporation exceeds rainfall by a significant margin. Approximately 30 per cent of rainfall infiltrated the uncovered cells. Rainfall infiltration into the fine coal discard was reduced to 20 per cent and 15 per cent for a 300 mm and 500 mm cover respectively. Infiltration was reduced to ten and 12 per cent of rainfall for fine coal discard provided with a 1000 mm double soil cover and a compacted bottom layer. This relatively high infiltration was probably caused by moisture being entrapped in the bottom retentive layer, and not being released by evapotranspiration. The best performing cover comprised 1000 mm single soil with a compacted bottom layer and infiltration was reduced to four per cent of rainfall. Rainfall infiltration into sloped cells varied between seven per cent and 14 per cent of rainfall. The computer software, SoilCover, was used to predict infiltration and moisture content in the cover. Predictions of rainfall infiltration were accurate, but were less accurate for covers where the hydraulic properties of field compacted soils were not adequately characterised. Oxygen ingress was significantly reduced for cells provided with a 1000 mm cover. Oxygen concentrations were generally below one per cent, with the exception during exceptionally dry periods when the cover dried out, resulting in increased oxygen ingress. For other covers, and the uncovered cells, oxygen concentrations were close to atmospheric concentrations. During the eight-year monitoring period, acid breakthrough occurred in five of the cells, including three uncovered cells, one cell with a 300 mm cover and one sloped cell. In contrast, cells covered with 1000 mm, bottom compacted soils shows a marked improvement of leachate quality, indicating that sulfide oxidation processes have been slowed. There was a distinct relationship between oxygen ingress and leachate quality for all of the cells. No cover degradation was evident over the eight-year period, except for some erosion observed on a sloped cell. The results indicate that the onset of acid drainage can be delayed by perhaps hundreds of years and salinity loads can be reduced by more than 90 per cent, if coarse coal reject dumps in the KwaZulu-Natal provinces in South Africa are provided by an adequate cover system. These research outcomes can be extrapolated and applied to other dry site regions where similar materials are being considered.

Jan 1, 2003

A hidden asset in most exploration and mining activities is data. Common practice involves the spending of large amounts of money to discover, define and prove the viability of a mining project. Some organisations have used operations research analysis and internal costing methods to allocate a value to their data and to compare the costs of data maintenance to other more tangible activities like plant and equipment maintenance. Those organisations, which do not undertake such an analysis often, have little knowledge or understanding of the extent and the worth of their data. Often the organisations lack of knowledge and understanding of the data is indicated by their failure to fully exploit or realise their opportunities. The focus of this paper is to discuss new technologies that optimise the management and security of collected and derived data. The technologies discussed are components of the software systems acQuire and MineSight.

Jan 1, 1999

By C Fischer

The introduction of digital communications technologies into the underground mining industry, in both coal and hard rock mining, has enabled high bandwidth applications to be applied in the mining industry. Digital networks based on 802.11 b/g/n open Wi-Fi standards have allowed numerous applications to be run over a single communication backbone. One of the many important applications is the tracking of personnel and equipment via RFID Tags. This tracking application has formed the basis of a Proximity Detection System or Collision Avoidance System (Schiffbauer and Mowrey, 2001; Kent, Fischer and Schiffbauer, 2011) thereby improving safety and increasing control in the mining environment. This paper discusses the growth of digital technology as the backbone for communications in underground mining applications. This growth has allowed the ‘convergence of technologies’ (occurring in the general business world) to be available to mine operators in general and underground mine operators in particular. Mine Site Technologies’ involvement with major mining companies and mining equipment manufacturers (OEMs) in developing and supplying their communication systems is also discussed.The latest technical requirements and specifications for communication systems for underground and open cut mines will be reviewed.

Nov 22, 2011

The status of remote sensing data availability in New Zealand is outlined and discussed. Currently, two multispectral remote sensing satellites are providing regular data over New Zealand; aircraft scanner services are available from Australia.; operational radar satellite services are yet to materialise. The advantages and disadvantages of the various data types are compared and contrasted. Some image processing considerations are outlined.

Jan 1, 1993

By M I. Pownceby, J Manuel, S Suthers, A Poliakov, E Donskoi, N Ware

"The mining industry is constantly seeking methods for optimising the exploitation of mineral resources, such as iron ore, in a sustainable and eco-efficient manner for economic and social benefit. When faced with resources that have mineralogical or textural complexity, poorer grades or geological variability, it is particularly important to apply a comprehensive geometallurgical approach to the development of the mining operation, from resource definition through to processed product. Integral to this approach is the quantitative characterisation of representative samples across the whole orebody.A key factor that associates the geological characteristics of iron ores to their processing response is ore texture. While the classification of samples on the basis of chemical or physical properties alone is often not sufficient to predict their processing behaviour, classification and quantification of texture types can be effectively correlated to metallurgical performance in processes such as blending, beneficiation, pellet making, sintering and ironmaking. This paper describes some of the research conducted by CSIRO pertaining to the design and rationale of a texture-based classification system for Australian iron ores; some of the tools developed and used to apply such classification; and the application of the generated data to quantifying, modelling and predicting sintering behaviour and performance in the blast furnace.CITATION:Suthers, S, Pownceby, M I, Manuel, J, Ware, N, Donskoi, E and Poliakov, A, 2016. Geometallurgical Characterisation of Australian Iron Ores – from Ore to Processed Product, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By A D. Campbell

Sublevel caving (SLC) is a mining method adopted in a wide range of mining depths and ground conditions with various layouts adopted to suit orebody geometry. Sublevel caving offers more flexibility and versatility compared to other cave mining methods and is a low cost alternative to open stoping. SLC also has the advantage that stopes are not required to remain stable during production, and no backfill is required. This flexibility combined with increasing pressure on mines to target deeper and lower grade mineralisation has led to increased uptake of the method. The implementation of SLC mining methods across a wide range of mining depths and rock mass conditions has led to ground control practices which vary globally from mine to mine. To date, there has been limited documentation of ground control practices in SLC mining and few benchmarks available in the literature. This paper describes the main findings from a global benchmark of sublevel cave mines conducted over three years as part of the Caving 2040 research consortium. The purpose of the project was to document and compare operational practices, technical aspects and hazard management techniques across SLC mines around the world. The review included 21 mines spread over four continents and 17 different mining companies. This paper provides an overview of geotechnical conditions, challenges and ground control practices at each of the benchmarked SLC mines. Mine design and sequencing practices adopted for ground control purposes and hazard mitigation are provided with case studies. The impact of depth and rock mass conditions on mining productivity and development rates is also described.

Nov 29, 2022