Search Documents

By C J. McKenzie, D F. S Natusch

The lignite deposits of Southland and Central Otago are a potentially significant energy resource for New Zealand. Current estimates put the technically mineable lignite reserves at 5.3 billion tonnes, which is more than ten times the energy content of the Maui gas field. Thus, the strategic importance of the lignite as a basis for maintaining current levels of self-sufficiency in transport fuels, or as a possible feedstock for electricity generation, deserves full investigation. The full extent of the lignite deposits was only recently established as the result of a scout drilling programme undertaken between 1976 and 1979 by the Mines Division of the Ministry of Energy, and from companion studies conducted by the New Zealand Geological Survey. These discoveries of large quantities of lignite coupled, at the time, with rising oil prices, raised the prospect of their development for production of transport fuels.

Jan 1, 1983

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Before exploration programmes or minerals developments are formulated, a mining company ought to assess how capital can be returned if the project is successful. A fact not well appreciated by the minerals community is that it is often difficult to get money out of many Pacific Rim countries due to special foreign exchange controls or restrictions on dividend or capital repatriation. On top of this risk are factors such as creeping expropriation through administrative, fiscal, or corruption pressures; environmental regulations; terrorists; and organised labour and political activists. Political risk is much more than just expropriation or nationalisation.Political risk factors can make or break a project in many PacRim countries and just the cost of delays and negotiations can insidiously affect project economics. This unpalatable thought, however, can be readily addressed by either legal structuring e.g. offshore proceeds accounts, offset/back-to-back currency hedges, or political risk insurance for the equity as well as any subsequent project development debt.

Jan 1, 1990

By A D. Wulfse, C M. D Barton

Underground fractured aquifers in the Ernest Henry deposit are to a large extent controlled by deposit scale brittle structures. The underground mine has been subdivided into nine water zones based on hydrogeological characteristics, including conductivity and connectivity, within the mining areas bound by these structures. The nine water zones and the hydrological characteristics of the associated structures are utilised for risk assessing mine development and for targeting diamond drilling dewatering activities. Wireline and conventional underground diamond drilling techniques have been used throughout the network of underground aquifers with the aim of dewatering areas within the mining footprint. These dewatering drilling campaigns have historically been highly successful at lowering aquifer water levels throughout the underground workings. As part of recent mine expansion activities, diamond drilling has intersected high pressure (>507 psi), high temperature (>50°C) and high flow water (>3 L/sec) in as yet unconstrained underground aquifers. Groundwater is typically conducted through rubble and clay rich faults, further hampering progression of drilling. Drilling through fractured aquifers at depth presents both mine planning as well as safety challenges. Recent drill holes have been delayed or abandoned when aquifers hosting this high pressure, high flow water have been intersected, risking mine planning deadlines. Recent technological innovation developed to control groundwater outflows from the diamond drill hole whilst drilling has been trialled at the Ernest Henry Mine. This case study focuses on the utilisation of alternative drill methodologies to allow the current drilling campaign to continue without delay, whilst also improving safety conditions encountered on the drill site.

Mar 22, 2022

By R Valenta

Most developing projects face a range of technical and non-technical challenges, and examination of development histories can potentially provide insights into improved approaches to project development. The Kestanelik project in the Canakkale region of Western Turkey was acquired by Chesser Resources Ltd in 2008. Turkey is a significant and growing source of gold production, with sector participation by both domestic and international companies. While the broad ranges of challenges faced by developing projects is well known, there are relatively few case studies in which the range of technical, environmental, social and governance challenges are presented in a single contribution. Recent studies of undeveloped complex orebodies have particularly shown the extent to which environment, social and governance (ESG) complexities contribute to project delays and failures. The Kestanelik project faced a full range of technical and ESG complexities, and provides an illustrative example of the associated challenges. CITATION: Valenta, R, 2018. A case study of technical, social and environmental challenges for a gold project development in Western Turkey, in Proceedings Complex Orebodies Conference 2018, pp 73–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By E Ruhanen, S Kauvosaari, M Kosonen, C Meintjes

The Yara Siilinjärvi plant is located in the central part of Finland. Siilinjärvi is Western Europe's only apatite mine and annually it produces 1 Mt of apatite concentrate, which creates approximately 10 Mt of tailings.At the beginning of 2017, tailings handling in Yara Siilinjärvi was brought to a new era, by replacing the conventional tailings storage facility with a new tailings treatment plant. The new high-density tailings disposal system with two paste thickeners increased the percentage of solids in the slurry from 45–48 per cent to 66-68 per cent, making it possible to deposit as a paste. This extended the life-span of the current tailings storage facility by 15 years; from 2020 to 2035.This paper presents the storyline of the Yara Paste Plant Project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After some successful pilot trials, the final process design was implemented. Process instrumentation and automation played a key role in the project, as the aim of the Yara Project was to make the plant operable remotely from the main plant. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances.This paper discusses the results from the Yara site since the new tailings treatment plant commenced. Some of the main points are that the operation has been running consistently with an underflow solids content of 66-68 per cent, with average beach slope angles of 3.5 degrees in the tailings disposal area. This control system additionally facilitates minimum use of flocculant, which delivers significant savings to operating costs. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the Paste Plant. During the first year of operation, the plant’s availability has been very good, over 97 per cent.Currently, the plant still has its own staff working there during the daytime, but the Paste Plant is now already operated remotely during the night shifts. The long-term goal is to gradually transition into operating the plant completely remotely.CITATION:Ruhanen, E, Kosonen, M, Kauvosaari, S and Meintjes, C, 2018. Optimising the operation of paste thickening at the Yara Siilinjärvi Plant, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 297–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

It is now becoming mandatory in Australia to rehabilitate ponded fine grained coal mine tailings, which may well have been deposited initially with no consideration as to how or whether this could be done nor to the costsinvolved. Of prime importance to the rehabilitation of tailings ponds are the bearing capacity and deformation characteristics of the tailings. Since the tailings are fine grained, time effects will govern the self-weightdeformation of the tailings initially deposited as a slurry and the subsequent deformation of the deposit under the weight imposed by rehabilitation fill. The engineering properties of a particular deposit of ponded tailings havebeen investigated and its response to the placement of fill monitored and analysed.

Jan 1, 1987

By K C. Runge, E Tabosa, A Jankovic

Flotation recovery in geometallurgical modelling is usually predicted based on relationships developed from batch flotation testing of different ore types. These batch flotation tests are usually performed at a constant set of operating conditions and at a fixed feed grind size P80. Usually the laboratory feed grind P80 is that which is expected to be produced in the full-scale flotation circuit for that particular ore type.Flotation recovery will be a strong function of the valuable mineral particle size distribution, with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation of this fraction. This valuable mineral particle size distribution is not characterised by the solids P80 parameter alone. The proportion of material in each class will also be a function of the slope of the size distribution and the degree of preferential grinding of the valuable mineral in comparison to the total mass of the ore.This paper will demonstrate (through example) how these other size distribution parameters can change with a change in grinding technology, the size and operating conditions used in a grinding unit and the characteristics of the classification technology used in conjunction with the grinding unit. Case studies will be presented that demonstrate how this can result in these parameters being very different in laboratory testing to that produced in the full-scale comminution circuit. A rule of thumb that laboratory rod milling rather than ball milling produces a size distribution most similar to that of the full-scale grinding circuit will be challenged. These differences can result in a significant change in flotation recovery. It is therefore important to consider these parameters when developing a laboratory geometallurgical program, to enable more accurate prediction of the flotation recoveries that will be achieved in the full-scale process.CITATION:Runge, K C, Tabosa, E and Jankovic, A, 2013. Particle size distribution effects that should be considered when performing flotation geometallurgical testing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 335-344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The Archean Gossan Hill Group at Golden Grove, Western Australia, hosts two potentially economic volcanogenic massive sulphide deposits. The volcanic-sedimentary succession hosting this mineralisation is composed of a facies association which includes the products of rhyodacitic to,andesitic effusive volcanism, mass-flow sedimentation and concentrated hydrothermal fluid discharge, in a deep subaqueous setting. The Tertiary Kuroko deposits of Japan are widely compared to Archean volcanogenic massive sulphide deposits and a comparison of the facies associations hosting this style of mineralisation, in these two successions separated widely in time, allows a refinement of facies models suitable for exploration in ancient successions. The required deep subaqueous environment for the formation of volcanogenic massive sulphide deposits places constraints on the physical processes that can operate during accumulation of the host stratigraphy. Limitations on the operation of physical processes is reflected by the resultant facies association which can be used to characterize suitable volcanic-sedimentary successions in which volcanogenic massive sulphide mineralisation may be present. The facies association includes: (1) proximal effusive volcanic products - lavas and associated autoclastic breccias (2) distal volcanic products - mass-flow resedimented pyroclastic debris (3) background sedimentation - reworked volcanogenic and terrigenous mass-flow sediments and (4) chemical sediments - exhalites including cherts, sulphides and oxides, with perhaps various carbonates and sulphates. Primary pyroclastic deposits are not expected to be present, other than distal water-lain air-fall deposits, derived from shallow to emergent basin margin explosive volcanic centres, which also provide a source for the resedimented pyroclastic debris.

Jan 1, 1987

By C B. Smith, G L. Boxer, S W. Moss, A L. Jaques, V Lorenz, M J. Rayner

The Ernest Henry Iron Oxide Copper Gold deposit is hosted in a large dilation between two moderately dipping shear zones found in the footwall and hanging wall of the deposit. These shears are controlled by a large diorite intrusion to the north-east and south-west of the deposit, formed ~1660 Ma. A shear zone dubbed the ‘Interlens’ uncovered through underground workings truncates the main orebody into two lenses, and is hypothesized to have formed in conjunction with the Hanging Wall Shear Zone and Footwall Shear Zone. All three shears dip moderately to the SSE (50–140) from open cut exposures through to the current mining horizon approximately 800 m below the surface. Routine geological work and a capital drilling campaign has identified a significant flexure in these sub parallel ore bounding shears with increasing depth. A shift in shear orientation in the Interlens over approximately 100 m vertically from ~50° to the SSE to a steep, easterly trend (~85° to the east) is observed in both drill core and exposures in the underground workings. It is hypothesized the diorite intrusive to the south-west of the deposit controls the shear zone geometries at depth. The geometry of the Interlens mirrors the surface expression of the Proterozoic package of the orebounding shears to the south-west of the deposit, suggesting the surface geometries of the shear zones are consistent with depth. Additional drilling to explore the validity of this hypothesis is planned for the near future to better understand the structural controls on the Ernest Henry mineralisation with increasing depth.

Mar 22, 2022

By R D ROSENTHAL

BHP Iron Ore Ltd's Mt Whaleback is the largest single open-pit iron ore mine in the Pilbara region of Northwestern Western Australia. A division of BHP Minerals, one of three core businesses of Broken Hill Proprietary Company Ltd (BHP), BHP Iron Ore - Newman is a joint venture with minor participants C Itoh Minerals and Mitsui. Mine planning for Mt Whaleback generates detailed sequence plans for a long term forecast incorporating equipment requirements, marketing forecasts, and pit development strategy. Utilisation of several computer packages, both commercially available and site modified, are necessary to achieve such a demanding task.

Jan 1, 1992

Computation is believed to be a powerful tool in scaling-up chemical processes and in designing materials, however, is being challenged by low predictability and limited scalability. This presentation will discuss the promising future of multi-scale computation in solving these two problems to realise the real-time simulation of industrial processes. Multi-scale structures are a common nature of most chemical systems and the meso-scale phenomena are believed to be the road blocks not only in improving the predictability of physical modeling but also in extending the scalability of computation. Focusing on the meso-scale phenomena, a series of research has been carried out at the Institute of Process Engineering, Chinese Academy of Sciences, for the past three decades. Starting with a simple idea of modeling the meso-scale clusters in gas-solid two phase flows, the so-called EMMS (Energy-Minimisation Multi-Scale) model was established. In verifying the stability condition of the model, the pseudo-particle approach was proposed to explore the micro-mechanisms in particle-fluid systems, and the strategy of the EMMS model was extended to other six different multi-phase systems, resulting in a unified conceptual formulation of multi-phase complex systems expressed by a multi-objective variational problem. In applying this model to different multi-phase systems and to industrial problems, it was recognised that the EMMS model defined a new paradigm of multi-scale computation by realising the structural similarity between software, hardware and the problems to be computed. This paradigm of computation was implemented on a multi-scale supercomputer with a capacity of 1.0 petaflops by integrating CPUs and GPUs (Graphic Processing Units), showing high efficiency and low cost. Running the EMMS model on this computer, the simulation of hydrodynamics of multi-phase systems can be speeded up very much, indicating a promising future of virtual reality of process engineering. The presentation will review this series of work, introduce successful applications in industries, and will be concluded by emphasising the critical importance of the meso-scale phenomena as the bridge between macro-dominants and micro-mechanisms. This is an ABSTRACT ONLY. No full paper was prepared for this presentation.

Sep 13, 2010

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

Good morning and thanks for the chance to talk to you. It's really pleasing to see so many industry representatives here I want to spend a few minutes talking about issues relating to your industry. At the end of today I would like to leave you with three strong messages from government. The first is that this government supports environmentally responsible mining and the endeavours of the mining industry. The second is that explorers and developers are wanted and welcomed in New Zealand. And the last is that it is up to the industry to keep the public properly informed about how your industry and to constantly work on improving your public image. The mining industry is a high-tech industry which fits snugly with our concept of a growing knowledge-based economy. It has particular value for regional development, the gold mining industry alone provides more than 4,000 jobs û mostly outside of the main cities. The industrial minerals industry is twice as large as that. As well as those people directly employed by the industry there are greater downstream effects for the community. One example from the broader extraction industry of this is of the local pie shop down the road from one of Taranaki's petroleum industry locations. The shop sells over $4,000 worth of pies a week to workers in the industry. That's just one example of the positive benefits the industry brings to its local community and is the sort of real positive benefit you need to be telling people about  

Jan 1, 2000

By D McInnes

Rather than look at the problems associated with sampling, this paper deals with the issue of sampling and blending to optimise revenue û predominantly in the mining industry. An example of the use of this methodology in the agriculture industry is also presented. Mining companies, in particular, are experiencing a boom in commodity prices and many believe the industry is in the middle of a æsuper cycleÆ. Production levels are being escalated dramatically to meet the demand coming from China and India. This in turn has further stretched the capacity of our rail and port infrastructure û resulting in significant shipping queues around most Australian commercial ports and increased demurrage costs for the producers. Mining companies are now looking for effective scheduling, planning and blending to maximise production and reduce demurrage charges û given the current infrastructure constraints. Mining companies can no longer use spreadsheets to run their business. This paper further looks at how these outcomes can be met by optimised blending using an integrated supply chain management system such as MineTrak together with effective sampling and analysis.

Jan 1, 2005

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

I was delighted to be invited to be patron of this Joint Conference, but the challenging task you have set yourselves, and your speakers' depth of expertise, deny anyone, even the patron, the opportunity to be patronizing. Australia's history has been inextricably link- ed with the fortunes of our great mining industry. That link will remain. Just as the gold rushes of the last century, and the discoveries at Kalgoorlie and Broken Hill changed the lives of generations, so the more recent development activity in iron ore, bauxite, nickel, coal, and uranium are having a significant impact on the lives of Australians today. The minerals industry has contributed to Aust- ralia's jobs and prosperity. Mining is not free of problems, but so long as safeguards are strong and appropriate the net benefits the mining in- dustry brings Australia will continue to be enor- mous. We rely on our mining industry to find, prove, develop and sell our minerals profitably, and my Government is committed to maintaining a healthy mining industry.

Jan 1, 1978

By Wernick B. J

Recently, the Environmental Engineering Laboratory of the Chamber of Mines of South Africa Research Organization has made signifi- cant progress in the development of more accurate algorithms for assessing heat flow in gold mines. These algorithms have been incor- porated into an overall computer program, ENVIRON, which enables the complete thermo- dynamic analyses of mine ventilation and cool- ing systems to be carried out. Recently, efforts have concentrated on the development of an expert computer system which will guide engineers in the process of selecting the most appropriate environmental control strategy.

Jan 1, 1988