Search Documents

Ecological Fuel from High-Sulfur-Content Coal

Sep 13, 2010

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

By Gibbons S. L, Ritchie I. M, Murr D. M

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1990

A comprehensive understanding of the rocks associated with coal seams, and also of the coal itself, is essential in assessing the likely behaviour of the materials before, during and after the mining process. The nature of the rock materials involved in coal mining can give rise to risks from adverse geomechanical properties, create problems in coal quality control and produce difficulties with environmental impacts, all of which may affect the profitability, impact and safety of the operation. Examples of issues associated with rock composition include slaking and degradation leading to roof, floor, pit wall or spoil pile instability, ignition of methane in mine atmospheres by frictional processes, liberation of quartz-rich dusts into ventilation systems, production of coal with unfavourable preparation or marketing characteristics, and escape of suspended solids or potentially toxic leachates from spoil piles and other types of emplacements. Methods for evaluating rock composition include microscopic examination, chemical analysis and X-ray diffraction, with the latter being especially useful for fine-grained rocks or for clay-bearing materials. Other techniques, such as geomechanical testing and down-hole geophysical logging, are also useful, but give less direct information about the actual composition of the materials involved. Indeed, understanding of rock composition, through microscope or quantitative X-ray diffraction studies, provides a basis for checking information from other sources, explaining different aspects of rock behaviour, and an essential link in relating geophysical or geotechnical data to broader-based geological models as part of the risk assessment process.

Jan 1, 2003

The development of the Australian uraniumindustry over the last decade has been subjectto socio-political controversy, but the industryis now beginning to emerge onto the world scene.The socio-political controversies which haveexisted over developing Australian uranium arediscussed and suggestions put forward as topossible changes in the relationship of themining industry to the pplitical and socialstructure of Australian Society.The rate of growth in energy consumptionis considered and on the basis of a growth rateof 3% by the year 2000 the world will beconsuming twice the amount of energy that itdoes today. It is anticipated that the growthin generation of electrical power will begreater than the growth rate fQr energy.The dominant part played by coal and nuclearpower in the generation of electrical power isdiscussed. Nuclear power at present, contributesabout 4% of the world's electricityrequirements and by the turn of the centurythis could be nearer to 30%.

Jan 1, 1981

By Mimura K

The carbon reduction of tantalum pentoxide was investigated in a plasma-arc furnace. The sample was a mixture of tantalum pentoxide and graphite, vacuum pressed into a briquette and was reduced at about 3100¦C. Argon was used as the are gas. The optimum mixing ratio of carbon and tantalum pentoxide, C/Ta205 is 5.10--5.15. The sample, weighing 7 g is fused within 60^ 70 seconds by plasma-arc heating and the reduction of molten tantalum oxide with solid carbon pro- ceeds rapidly to approximately 99.5 % Ta during this period. The reduction that follows in the molten state is slow. Within about 10 minutes, the maximum tantalum content of the massive metal product reaches 99.9 % and the oxygen and carbon remaining in the product are 50 ppm and 400. 500 ppm respectively.

Jan 1, 1980

By K Dagdelen

A vehicle proximity warning system is being developed using GPS and wireless local area networks to improve safety of off-highway trucks in open pit mines. After two an a half years of research, software development, and laboratory testing, field tests were carried out at operating limestone quarries and open pit mining operations to evaluate GPS accuracy and overall system effectiveness under rugged operating conditions. This article describes the progress made on this NIOSH funded project and discusses the GPS accuracy tests and overall system tests that were carried out during 2001 at the Morenci open pit copper mine in Arizona.

Jan 1, 2003

By Singh RN

The Bulli Coal Seam, located in the Illawarra Coalfield of New South Wales, has a long and varied history of sudden outbursts. From available information this problem has resulted in twelve fatalities over the last one hundred and one years, with over five hundred separate outburst incidents being identified. These incidents have varied in severity and intensity from the discharge of 1 to 2 tonne of coal, with a slight increase in gas emission, to the discharge of 200 to 400 tonne of coal with some 6,000 m3 of gas being liberated and large items of mining equipment being pushed 1 to 2 metres down the roadway.Geological features associated with these outbursts can be mapped on a regional and mine by mine basis, to provide some indication or warning. Similarly changes in gas content and gas composition can also be determined on a regional and mine by mine basis. However sudden geological changes (such as a 6.5 metre seam displacement within 15 metres) variations in gas content (such as 6 m3/tonne to 15 m3/tonne) and changes in gas composition (from 95% CH4 to 90% CO2) all within one mine does make the prediction or forecasting of outburst incidents exceedingly difficult.

Jan 1, 1998

This paper describes the planning mechanism and implementation of a progressive rehabilitation programme at Hunter Valley Mine in the Upper Hunter Valley of New South Wales. Hunter Valley Mine is a large open cut coal mine which produces approximately 7.0 million tonnes of coal (run of mine) annually for export. This production level involves the movement of some 60 million tonnes of waste and coal each year.The rehabilitation programme at Hunter Valley Mine has been developed to provide a combination of pasture, based on improved pasture species and timber belts to enhance the visual characteristics of the rehabilitated landform, whilst creating amenity in the form of shade for livestock.The operational philosophy for the rehabilitation programme is that of progressive rehabilitation. The best time to undertake rehabilitation is now.' As a result, planning for the rehabilitation programme is continuous, so that all site works are completed in time for vegetation establishment during the critical periods each year.

Jan 1, 1992

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

The kinetics of chlorination of alumina and bauxite with CO/CI2 mixtures were studied in the range 300-1100°C. The temperature of prior calcination is critical in determining the reaction rates. An optimum chlorination temperature in the range 600°C-750°C was demonstrated such that there is no increase in reaction rates with increasing temperature. This lack of rate sensitivity to rising temperature is largely a function of the influence of gaseous diffusion gradients in the porous alumina together with a progressive decrease in surface area.

Jan 1, 1976

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

By Kruse JW, Kjar AR

Recently there has been increased recognition o'f the cost savings that can be achieved by the greater use of offsite preassembly for the construction of industrial plants. Preassembly is a method of construction which involves considerable offsite assembly of complete sections of an industrial plant in established fabrication shops. The preassemblies are transported to the plant site, often by large and oversize transport systems where they are set on prepared foundations, finished and interconnected to other sections of the plant as required. The concept of preassembly is not new, but widespread interest has been shown because site construction costs in all parts of the world have increased rapidly and often at a greater rate than in established fabrication areas. Particular interest has be focused on remote, isolated and inhospitable plant site locations. These areas require the import of skilled labour, the payment of high labour rate premiums and the development of infrastructure to support the workforce for the duration of the construction period.

Jan 1, 1983

In eastern China, most of the copper skarn deposits occur in folded troughs which are controlled by the EW-trending faulted fold systems (the Pal-Asian geotectonic domain), and the NNE-trending rift or fault zones (the Marginal-Pacific geotectonic domain), particularly the later. From the north to the south, there are four troughs hosting the main copper skarn deposits in eastern China: the Yanliao Trough, the Yangzi River Trough, The Qiantang-Yuanshui Trough and the Zichen Trough. There are more than 30 copper skarn deposits in eastern China, and ore reserves of each deposit are between 30 to 100 Mt with average grades over 1 % Cu.

Jan 1, 1995

By Gigmai W

Ok Tedi Mine is a high production open pit porphyry copper mine located high in the Star mountains of Papua New Guinea. The mine produces an average of 160 000 tonnes of ore and waste daily at a 1:1 strip ratio. Full scale drilling and blasting began in 1988, prior to which time all material was ripped and dozed.Drilling and blasting procedures at Ok Tedi underwent a major review commencing mid-1989. As a result of a mutual commitment by management at Ok Tedi and the mines explosives supplier ICI, significant reductions in overall blasting costs have been realised. These cost savings are primarily the result of the introduction of air bags, expanded patterns and better field execution.

Jan 1, 1992

I am sure that you are- all familiar with Airborne Magneto-meter Surveying so I shall-spend only a brief moment describing the instrument and techniques and the remainder of the allotted time-on-modern-application-of the instrument.The Airborne Magnetometer used by Aero Service in AUstralia-was designated by Gulf Research and implements the saturable-core flux-gate--principle. The first magnetometers developed'weremagnetic-balances and depended on the counter-torque principle but these required a stable platform and hence are not applicable to airborne surveying. Other methods include the induction methods, the Hall Effect methods, magneto-striction methods., Deflectioh. of,free.electrons, the proton-precession methods.Some: of these are applicable to airborne surveying. As a matter of-fact the nuclear precession magnetometer is the one generally used in the Satellites because it has been miniaturized most successfully.The Gulf Magnetometer is the one most generally used in mineral and petroleum exploration because its sensitivity is sufficient for the problem and-data and instrument techniques have been worked out and standardized.

Jan 1, 1962

Access to the Rosebery Orebody, which dips into the western slopes of Mount Black at 45¦, has been achieved in sequence by the following means: - A series of adits down to 8 level - An inclined shaft (No. 1 Shaft) sunk internally from 8 level to 14 level - A vertical circular concrete lined shaft (No. 2 Shaft) sunk internally from 4 level to 19 level. Although the orebody has been fairly well defined to 19 level, deeper ore occurrences have been outlined by a series of drill holes decreasing in frequency with depth to 26 level. No. 2 Shaft (sink) was stopped some 10 m below 19 level in order to make an early start on doubled production at West Coast Mines, with the intention of subsequently extending the shaft or of driving a decline from the lowest operating horizon for deeper access. The decline approach was adopted some six years after production commenced from No. 2 Shaft. The reasons for that decision are outlined, together with an account of the constraints and design requirements imposed by commencing by a vertical shaft in the hanging wall of the orebody.

Jan 1, 1982

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences Ltd has carried out a mineral resource assessment of the Coromandel region, one of the most mineral-rich regions of New Zealand. The assessment focussed on metallic minerals and clays, because these are the main commodities that have potential for increased production and export from the region (and from New Zealand).   Three steps were used in the assessment: 1) development of mineral deposit models, 2) comparison of the models with regional geology, structure, geochemistry and past mineral production to estimate the number of undiscovered mineral deposits, and 3) application of grade-tonnage models to determine the quantity and value of the known and undiscovered resources. In step 1, descriptive and grade-tonnage mineral deposit models were developed for 11 different types of mineral deposits: ò     Low-sulphidation andesite-hosted epithermal Au-Ag ò     Low-sulphidation rhyolite-hosted epithermal Au-Ag ò     High-sulphidation quartz-alunite epithermal Au ò     Porphyry Cu-Au-Mo ò     Andesite-hosted polymetallic veins adjacent to mineralised porphyry stocks ò     Zn-Pb-Ag skarn ò     Cu-Ag skarn ò     Hot spring Hg ò     Shoreline placer Ti ò     Rhyolite-hosted halloysite clay ò     Volcanic-related kaolinite clay   Step 2 was aided by a geographic information system (GIS) assembled from a number of digital spatial data sets including: a digital elevation model, an aeromagnetic map (from open file mining company data), a geological map (from the GNS QMAP project), location of areas of hydrothermal alteration, locations of mineral deposits (from the GERM database), stream sediment geochemical analyses (from the REGCHEM database), and a lineament map derived from satellite remote sensing data and the digital elevation model.   Based on May 2001 commodity prices, potential resources estimated for the 11 mineral deposit and grade-tonnage models total NZ$22 806 million for the metallic minerals, NZ$1000 million for halloysite clay deposits and NZ$57 million for kaolinite clay deposits.

Jan 1, 2001

By Martin C. H, Met B

INDEX OF CONTENTS:1. Introduction, Explanatory; and Reasons for Coal Cleaning.2. Principles on which Coal Cleaning is based.3. Location of Broken Hill Proprietary Co. Ltd. Plant.4. Description of Processes Selected Barvoys Bath Process; Barvoys Medium Preparation and Treatment; Static Dry Cleaning Plant.5. Detailed Description of Plant.6. Typical Results of Cleaning Operations.INTRODUCTION, EXPLANATORY, AND REASONS FOR COALCLEANING:The Institute proceedings have not previously published any matter on coal cleaning and the reasons thereof; in consequence it has been deemed advisable to allot a part of this paper to explanatory matter, prior to entering into a detailed explanation and description of the Newcastle plant.At the outset it would be as well to consider briefly the kinds of materials from which coal has originated. All coals represent some stage in the decomposition and transformation of vegetable matter laid down in prehistoric times, the vegetable matter undergoing numerous geological changes, such as submergence, overlaying by sediment, with subsequent pressure and re-elevation; these processes may...

Jan 1, 1946

By McKee DJ

Future mineral processing developments will be of two types. There will be a continuation of the advances of the last 20 years including major increases in equipment capacities, the development of reliable on-line instrumenta- tion, the use of digital computers for automatic control, and the greatly expanded use of in-situ leaching techniques. However, there will also be a need for innovations as the industry faces a different set of problems to those involved in cost and extraction efficiency considerations. These new problems include those relating to energy usage, environmental pressures, and the further development of large low grade deposits and small, high grade metallurgic- ally complex deposits. Present technology does not appear adequate to solve many of these new demands. New treat- ment concepts will be required, and the immediate outlook in this regard is not encouraging. A major research and development task in mineral processing over the next 20 years will be to seek out new ideas and develop them, and this must be pursued with imagination and determination. Both the continuation of the present research pro- grammes and the development of new methods will require a steady supply of highly qualified technical personnel. These people are not being produced in the numbers required, and this situation must be urgently rectified.

Jan 1, 1981