Search Documents

By P Craig, A Crosky, H Ramandi, S Saydam, H Chen

Frequency of reports on premature failure of rock bolts and cable bolts have increased in past two decades. Such a failure threatens both the safety of underground mine workers and the economic viability of the operations. Herein, we report on analysis of rock bolts and cable bolts failed recently in three underground mines in Australia. Magnetic particle inspection (MPI) and scanning electron microscope (SEM) techniques were used to study the failed bolts. MPI showed a number of subcritical cracks on the surface of the bolts. The majority of the cracks in both cable bolts and rock bolts were initiated from the base of ribs (indentation) where the stress concentration was high. SEM examinations showed tearing topography surface (TTS) in all failed rock bolts and cable bolts. These indicated that the failure occurred through hydrogen assisted stress corrosion cracking (HISCC). The results of this study enhanced the understanding about the failure of rock bolts and cable bolts in underground mines. CITATION:Chen, H, Ramandi, H, Craig, P, Crosky, A and Saydam, S, 2018. Analysis of premature failure of rock bolts and cable bolts failed in underground coal mines, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 407–413 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Ruschitzka C

The productivity and economic success of a German hard coal mine is attributed to the high productivity of a small number of operation points; however high rates of production are associated with increased gas emission at the working sites. Therefore modem high technology is required in order to reach the planned production rate, since high methane concentrations often cause unplanned breakdowns in operation. The optimised simulation of gas emission is a fundamental planning tool for mine design as well as for determining the potential of a coal deposit and has increased in significance over the last years. Methane-INFO enables the three-dimensional, graphical simulation of a working site taking account of different aspects such as the mine design, ventilation, production rate, geology, seam quality, gas exhaustion, etc. The following paper gives a short overview over the benefits of the discussed system.

Jan 1, 1995

The necessity for agreed project outcomes, which are in accordance with client needs, and the subsequent requirement for a unique approach to managing project implementation is discussed. Reasons for appointing a separate project team to manage a project are established. The selection of a project manager, based on the services they can provide and on their characteristics, skills and management style, is discussed. The consequences of selecting the wrong project manager are explored. A broad overview of the requirements for the project team is provided. Criteria for the selection of team members, and the role played by the project manager in this selection, are discussed. The levers that drive `on-time and on-budget' projects are discussed in terms of the project's vision, goals, controls, and incentives.

Jan 1, 1997

By D E. Langberg, J S. J va, D R. Swinbourne

Specifications on the types and levels of impurities tolerable in metals are becoming increasingly stringent, and are pushing the limits achievable with conventional refining technologies. Particularly difficult is the removal of electrochemically noble elements with low volatilities, such as copper, from more active host metals such as lead, iron and aluminium. Electrochemical refining, utilising the ability of certain solid electrolytes to selectively transport copper or other impurity cations away from the molten host metal into a separate refining phase, may provide an answer to this problem. Numerous studies on solid electrolytes used in concentration sensors have been reported, as well as a limited number on metal refining. Oxygen anion conducting solid electrolytes have been applied to the deoxidation of copper and steel while cation conductors, eg ¯ -alumina and Nasicon materials, have been used to remove lithium and sodium from aluminium. However, solid electrolytes have yet to be applied to the removal of noble elements. The behaviour of solid electrolytes under the extreme conditions of molten metal refining is not well understood. This paper will examine the potential use of solid electrolytes to remove noble metals such as copper from active host metals such as iron. The suitability, and selection criteria of available solid electrolytes for implementation in the metal refining industry in the future will be discussed. In particular, the stability of Cusicon, a copper superionic conductor potentially suitable for use in metal refining, has been assessed and the results of the experiments are presented.

Jan 1, 2000

By Knijnikov M, Cameron D

Coal Quality management and the control of the flow of coal through complex mining preparation and transport phases of standard mining operations has assumed greater importance over recent years.

Jan 1, 1998

Progress on this project will be verbally reported and a description given of the main features. A detailed feasibility study was completed in December 1986, and the Joint Venture has issued an Environmental Impact Statement. This was open for public comment until 16 February. Issues presently being considered include economic justification traffic, air quality, noise, marine fauna and flora, visual impact, heritage and construction impact. Detail design and construction is likely to commence in mid 1987, following determination of the above matters.

Jan 1, 1987

Evolutionary changes to the original sizer concept are mild when compared to those which have taken place in the engineering standards embodied in today's commercially available machines. This paper examines the principles of sizer operation and reviews the development trends in new applications for this unique screen type.

Jan 1, 1978

By N Javati, G D. Carman, D Kikiha, B Likia, K Dala, J McPhie, R Johnstone, D R. Cooke, J L. Blackwell

The 40 Moz Ladolam gold deposit on Lihir Island, Papua New Guinea is the worldÆs largest, low-sulfidation, epithermal gold deposit, in terms of contained gold. The deposit has average grades of 2.42 g/t Au (LGL Resources Reserves Update, 2008) and gold is hosted primarily in refractory pyrite. Lihir Island is part of the 150 km long, Tabar-Lihir-Tanga-Feni, alkalic, volcanic island chain located in the New Ireland basin. Five volcanic blocks comprise Lihir; Plio-Pliestocene Huniho, Kinami and Luise volcanic edifices are built on top of remnant Pleistocene Wurtol Wedge and Londolovit Block (Wallace et al, 1983). The Ladolam gold deposit is located in the central portion of the dissected Luise volcanic edifice and is composed of four main orebodies: 1. Minifie, 2. Lienetz, 3. Coastal, and 4. Kapit. An active geothermal system is overprinted on the ore deposit, localised along north-trending lineaments, and is expressed as hot mud pools and fumaroles. The focus of open pit mapping and drill core logging, as part of ongoing PhD research, has been in the Minifie and Lienetz orebodies. The deposit geology is grouped into four main phases: 1. volcano-sedimentary host rocks, 2. porphyry-style biotite alteration and related hydrothermal breccias and veins, 3. epithermal-style breccias and veins, and 4. modern geothermal alteration. Gold is associated with epithermal-style alteration and mineralisation. Ongoing observations of the Minifie and Lienetz orebodies are highlighting differences in the geology and paragenetic histories. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

By A Gerdes, H BrStz, E GSbler, D Davis, F Henjes-Kunst, S Dewaele, T Graupner, T Oberthnr, M Sitnikova

Following the United Nations initiative to fingerprint the origin of conflict materials, the German Federal Ministry for Economic Cooperation and Development has decided to fund a pilot study on coltan ores. Since 2006, our working group has been investigating columbite- tantalite (coltan) mineralisation, especially in Africa, also within the wider framework of establishing certified trade chains. More than 300 samples were obtained from the worldÆs major coltan producing areas. Special attention is, however, directed to samples and concentrates from Ta-Nb-Sn provinces in Africa: Democratic Republic of the Congo, Rwanda, Mozambique, Ethiopia and Namibia. Using state of the art analytical tools, we investigate mineralogical and chemical parameters obtained from columbite-tantalite ores and concentrates in order to distinguish between ore provinces, likely even down to the deposit scale. Methods employed include fully automated electron microscopy (mineral liberation analysis), electron microprobe analysis (major and minor elements), laser ablation plasma-source mass spectrometry (trace elements and U-Pb dating), X-ray fluorescence spectroscopy (bulk major and trace elements), X-ray diffraction analysis (mineralogy and structure) and thermal-ionisation mass-spectrometry (U-Pb dating). Major and trace element concentration patterns, mineral assemblages in the ore concentrates, and zoning characteristics in the different pegmatites from Africa distinctly differ from each other. Furthermore, the following age populations are evident:Archaean (>2.6 Ga);Palaeoproterozoic (1.9 - 2.1 Ga);early Neoproterozoic (æKibaranÆ; 0.98 - 0.93 Ga); andlate Neoproterozoic to early Palaeozoic (ca 0.5 Ga). Currently, we focus on the resolution of the fingerprinting system from region via ore province down to deposit scale. Our preliminary analytical results indicate that a certification scheme including fingerprinting of sources of coltan ores is feasible.

Jan 1, 2008

By R Huntley, D Sims

Pajingo gold mine produces over 240 000 oz Au per year from underground mining using longitudinal bench stoping methods with a 15 m sublevel interval. Average mine head grade is around 12 g/t Au, contained within quartz veins between 0.5 to 16 m wide. The veins dip steeply (>60¦) and exhibit strike variations which lead to many curved and meandering drive/stope geometries. Unplanned dilution at Pajingo is predominantly controlled by fault planes that subparallel the vein and commonly lead to slabbing failure from the stope walls. Initial efforts at determining maximum spans were based on using the Stability Graph method of stope stability. However the method had a number of shortcomings that did not address mine site observations, including previous mining, interaction of different joint sets and the presence of discrete shears which resulted in poor prediction of stability. A method was developed to rate the risk of dilution for a stope based on observations made in the ore drives. The method utilises profile mapping of the ore drive, structural features observed and the orebody itself, on 10 m spaced sections along the ore drive. A matrix of factors determines the dilution risk for stoping at the time of mapping and the rating is transferred to longsection plots in the office. The dilution risk rating is used to determine the position and density of cable bolt support aimed at lessening the risk, and can be used to review blasthole designs prior to finalisation. The method has been used for more than two years and has proven to be a good indicator of potential unplanned dilution (ie waste outside of ring design). A recent review of the dilution risk mapping process has indicated it is assisting in reducing the impact of dilution at the operation and has the scope to be utilised further in the design process.

Jan 1, 2002

By E P. Donohue

Changes to water industry practice are required as a consequence of the Council of Australian Governments water reform agenda which binds all states and territories to a range of measures intended to drive new efficiency, sustainability, higher value use and proper provision for environmental needs. Queensland is implementing its reforms program through its water resource planning process, a legislatively underpinned program that provides for a new level of social, economic and environmental security. A water resource plan for the Fitzroy Basin has been finalised and its implementation plan, which details infrastructure operational arrangements for the basin, is due to be released later this year. The mining industry is a major contributor to the economy of the Basin, and although a comparatively minor water consumer, is now aligning its water use practices with the stateÆs maturing integrated resource management paradigm. This new culture presents both challenges and opportunities. Water reform in the Fitzroy basin is well advanced. The processes and institutional arrangements that have been developed are of significant importance to the aspirations of current and future minerals development. This paper outlines the current status of those reforms and the likely institutional framework for the near future. The paper also discusses how the reforms impact on the availability, access and security of water available to mining interests.

Jan 1, 2003

Preparation of MgO Nano-Particles with Magnesite

Sep 13, 2010

Optimising drill performance has always been a primary goal of drilling and blasting managers. Improving drilling rates and utilisation will ultimately drive the cost per foot or metre downward. Additionally, more consistent production will ensure shovel or dragline performance goals are met and the chances of machine idle time is minimised. Over the past 20 years, many studies have examined rotary drilling factors and performance issues. In most cases a common theory points to energy input versus drilling output. Indexes such as specific energy and total work energy have been -developed to quantify the drilling process. As general engineering principles dictate, energy is required to drill rock by overcoming compressive and shear strengths. Concurrently, the greater the energy input, the faster the penetration output. Therefore, by examining the basic drilling energy parameters, optimisation is possible. The principles of rotary drilling are driven by five factors. When optimised individually and as a system, drill performance will improve. Most recent studies all agree that a performance relationship exists between bit load, bit rotation, and hole flushing. Additionally, proper bit selection and most of all, the operator, can have a tremendous effect on drill productivity. By analysing these factors and establishing the best case scenario, an overall drilling system can be engineered to match the mining characteristics. Furthermore, by balancing these factors, a lower cost will be achieved through increased production rates, maintenance costs, and effective drill utilisation.

Jan 1, 1995

By P Grouhel

In the recent years several new blasting technologies have come into use in surface mines. Electronic initiation, low-density emulsion explosives and modelling software are in regular use throughout the world. In Australia, these new technologies have achieved significant application, largely in open cut coal mines where more than 20 per cent of blasting is now conducted with electronic initiation systems. These new techniques have contributed to the vast improvement in blasting outcomes evidenced by increased recovery of saleable product and faster excavation rates. In large surface mines, OricaÆs unique combination of electronic initiation systems, bulk emulsion explosives and modelling software can be harnessed to target critical value outcomes. This includes targeting better fragmentation, increased ore uncovery rates and better wall stability û all adding to improved mining operation profitability. Orica Mining Services have combined these technologies into a set of offerings called Blast Based Services (BBSÖ). The paper describes applications of these new technologies and possible benefits in large surface mines.

Jan 1, 2007

By S J. Tear, L D. Queen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Frieda River Project is located in the north-west of Papua New Guinea. The target commodities for a bulk mining operation are copper and gold associated with a large felsic porphyry system. The project comprises a series of deposits, with the Horse-Ivaal-Trukai (HIT) being the largest. It also includes the adjacent smaller Koki and Ekwai deposits.Previous resource estimates for the HIT were made using 14 separate mineralised domains based on structure, copper grades, lithology and alteration. H&S Consultants (H&SC) has revisited the deposit and concluded that a simpler methodology could be used for resource estimation without using wireframes as hard domain boundaries. This conclusion is based on reviewing all the available geological data combined with geological and resource experience of porphyry deposits.It is generally acknowledged that porphyry deposits form by diffusion of mineralising fluids through the host lithologies, meaning that sharp boundaries are unlikely unless these fluids encounter specific physical or chemical boundaries. It is important to prepare a comprehensive geological model prior to attempting resource estimation as it forms the framework for the estimates; however, not all geological features may be relevant to the distribution of mineralisation and there can be a tendency to overcomplicate the estimation process by using too many domains. Unless a hard boundary can be identified consistently and unequivocally, it is generally better not to use a boundary in that location.H&SC completed unconstrained models with no top-cutting using both a simple flat search ellipse and a steep search ellipse to generate global resource estimates reported within a predetermined pit shell at a 0.2 per cent copper cut-off. Both outcomes are within 10 per cent for the tonnes, contained copper tonnes and gold ounces compared to the constrained resource estimate. The slight differences are most likely due to the different search strategies, but also indicate the robustness of the unconstrained modelling approach.CITATION:Queen, L D and Tear, S J, 2015. The Frieda kiss – keeping it simple , in Proceedings PACRIM 2015 Congress, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

Process engineering principles are used to analyse the features of leaching processes for large masses of low grade, unprocessed ore. Different performance characteristics are related to the numerous variants of these processes. The variant for which reagent enters a heap only via the input solution is further subdivided into three modes of operation. The three modes may occur in testwork and full-scale operations; the effects of process variables on the rate of the process are completely different in each mode. The mode can be identified by the time at which reagent first appears in the pregnant solution. It is related to the ratio of the height of the heap and the thickness of a band of ore in which the reactions are localised. Synthesis of the phenomena occurring within a heap via a computer program has produced a quantitative relation for the reaction band thickness. The program has been validated for several different systems. The overall achievement is that the mode of operation and the rate of the process can be forecast before column testwork is commenced. Some applications of the outcomes to testwork, process design and operational tactics are described.

Jan 1, 1994

By M F. Navarrete

During 2003, different plastic stemming plugs (Cats«, Stemtite«, and Taponex«) were tested in EscondidaÆs Mina Sur, to determine the effect on gas retention time when used in conjunction with drill cuttings in production shots with a blasthole diameter of 10 5/8ö. Longer retention times were expected to provide greater fragmentation and muckpile looseness. In order to determine which plug showed the greatest enhancement of stemming retention, 17 trials were carried out û in the first seven tests, only the Cats were used, in the following five tests, a combination of Cats, Taponex and Stemtite were used, and in the last three tests, only the Taponex plug was used. In the last two blasts, drill cuttings were used without stemming plugs as a benchmarking exercise. Blasts were filmed with a high-speed camera, which could record the detonation times of holes using rolls of shock tube tied to stakes at the hole collars, to act as flash indicators. The camera allowed measurement of the time between charge detonation and the commencement of stemming ejection. In order to obtain the statistical parameters of each one of the stemming plugs used in the 17 trials carried out, the Minitab software was used and a data base was created for it, corresponding to each stemming configuration with the retention time obtained from the filming. Once it was determined which stemming plug provided the greatest enhancement of stemming retention, the impact on the fragmentation was analysed using the WipFrag image analysis software to estimate the muckpile size distribution.

Jan 1, 2004

By S Phinn, V Glenn, P McKenna, P D. Erskine, D Doley

The key goals for mine site rehabilitation require mine managers to demonstrate that rehabilitation is safe, stable, self-sustainable and non-polluting. Within this context, it is reasonable for stakeholders to expect that mine site rehabilitation is resilient to disturbance impacts such as fire and drought. However, mine managers actively avoid fire on rehabilitation; and as a result have limited understanding of fire behaviour on revegetated landforms, the long term implications for site stability and the potential risk to site relinquishment. An experimental fire that was conducted at the Curragh Mine site in May 2015, burnt 117 ha of 19- to 21-year old mine site rehabilitation, mimicking wildfire conditions and creating a mosaic of fire impacts across the landform. Using a combination of ground surveys and remote sensing assessments, we demonstrate that over a two year period, ecological metrics such as species richness, woody density and understorey biomass all recover to pre-fire levels for both grassland and open woodland areas. This is supported by WorldView-3 satellite imagery and the remote sensing assessment using the differenced Normalised Differenced Vegetation Index (dNDVI) which shows high regrowth within the burn area in 12- and 24-month image captures. The results suggest that within the recorded conditions, this site is resilient to fire impacts, and has the capacity to recover to pre-fire levels within the first two years following the fire.CITATION:McKenna, P, Erskine, P D, Phinn, S, Glenn, V and Doley, D, 2018. Measuring the recovery of coal mine rehabilitation following fire in Queensland using remote sensing and ground surveys, in Proceedings Life-of-Mine 2018, pp 141–146 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018