Search Documents

This paper is based on studies made intermittently from 1937 to 1950. Its object is to describe the surface geology and the tin lodes, and to relate the lodes to the structure of the field.PREVIOUS REFERENCESR L. Jack made his first report on the field in 1880, but his principal report was made in 1883. W. E. Cameron described the Great Northern lodes in 1904. Numerous later reports on various mines were made by L. C. Ball, J. H. Reid and C. C. Morton, the most important of which were on the Black King, Good Friday, St. Patrick and the Great Northern Gully Shaft.GENERAL GEOLOGYJensen maps the Herberton area as part of a granite massif intruding rocks of two ages, the Younger Metamorphics of Silurian-Devonian age, and the Older Metamorphics of Older Palaeozoic age. The distinction is apparently based on lithological data. The Older Metamorphic rocks occur as inliers in the granite massif to the west and east of Herberton (Fig. 1).The area described consists of granite traversed by numerous dykes. West of the area, approaching the Older Metamorphic rocks, the granite becomes finer grained as if chilled towards its contact, and the dykes more numerous. To the east, passing from the Nova Scotia mine to Mount Lavery there are numerous dyke rocks, but the outcrops are poor and knowledge of the geology indefinite. The area is the main tin-producing area. To the west there are comparatively small tin lodes in the granite, and the "Copper Firing Line" occurs in the Older Metamorphic...

Jan 1, 1951

By D Jordan, R Wilmoth, J LeFever

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the US Environmental Protection AgencyÆs, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open Pit Highwalls Demonstration Project. This project is funded by the US Environmental Protection Agency (EPA) and jointly administered by the EPA and the US Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome US, located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 m and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied in situ treatment technologies included: a modified, furfuryl alcohol resin sealant, utilising wood and agricultural by-products to coat the rock surface; EcobondTM ARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface; and two AMD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: ASTM D 5744-96, accelerated weathering of solid materials using a modified humidity cells; mine wall residual wall rinse sampling; microscopy; and core drilling followed by water injection testing. The following paper describes the technologies used for passivation of acid generation from the highwall, the field demonstration, and the testing results from the background and each technology plot.

Jan 1, 2003

By Fuerstenau DW

The flotation of pyrite in ethyl xanthate solutions is presented along with electrokinetic results. The results have been analysed in view of recently published thermodynamic calculations as well as other published data on the pyrite-xanthate system including adsorption and voltarnmetry studies. The flotation response of pyrite in xanthate solutions is characterised by two maxima, one at pH 4 and the other at pH 8-9. The acidic maxima is also associated with a reversal in the electrophoretic mobility of pyrite, probably due to the formation of ferric xanthate on the pyrite surface through chemisorption of xanthate ions while the basic maxima is not associated with major changes in the mobility and flotation at this pH can probably be attributed the adsorption of dixanthogen. It is concluded that there is not sufficient experimental evidence to conclusively attribute the lack of flotation response in solutions at near neutral pH to any particular phenomena, either kinetic or thermodynamic.

Jan 1, 1993

Blasting, particularly bench blasting, uses finite length cylinders of explosive close to two free faces. The rock to be blasted is usually intersected by a complex 3-D system of joints. To fully simulate a blast, a 3-D dynamic model is required. It is shown that the static stress distribution around a long cylinder can be reproduced by superposing the static stress distribution of a suitable chain of spheres. Thus, the dynamic results for individual spheres given by Favreau (1969) can now be substituted for the static results to give a dynamic model of the stress distribution around a long cylinder. Comparison of measured and computed waveforms show that the measured waveforms are much more attenuated and dispersed than expected. The consequences for explosive evaluation and design are Discussed.

Jan 1, 1990

By Weller KR

Completely dry or completely wet materials are comparatively easy to screen, but materials with moisture contents between these two extremes can present varying degrees of difficulty. The presence of moisture can impair the performance of a dry screening plant in a number of ways: ò agglomeration of fine undersize particles onto larger oversize particles, resulting in the fine particles being misplaced to the oversize; ò increasing attractive forces between particles that hinder stratification and particle presentation to the screen; and ò blinding of the screen apertures caused by fine moist particles clinging to the screen which reduces the effective aperture size and the open area of the screen. Test work on full-scale screens has shown that the agglomeration of fine particles onto larger particles only occurs once the equilibrium moisture content of the ore is exceeded, and that the quantity of adhering fines present is proportional to the surface area of the larger particles. An -adhering fines screen model has been developed from this work, and by using relationships derived between the model parameters and feed moisture content, the effect of changes in feed moisture on both product quality and operation of iron ore dry screening plants is predicted.

Jan 1, 1993

New South Wales mining legislation reinforces a systematic approach to safety management. It is now a requirement of all mines in the coal, metalliferous and quarrying sectors in NSW to prepare a Mine Safety Management Plan. The paper briefly outlines work currently being undertaken by the Safety Operations Branch of the NSW Department of Mineral Resources (DMR). The DMR is working proactively with NSW mines in the preparation and implementation of effective Mine Safety Management Plans. There is a growing realisation that a systematic approach to safety management, underpinned by the process of hazard identification, has real potential to improve safety in the workplace. The paper briefly describes the framework used in a current æmines education programÆ and its æduty of careÆ foundation. Particular attention is paid to the role of mining operators in the implementation of Mine Safety Management Plans and their expected behaviour in demonstrating compliance. One challenge is convincing some mining operators that they must adopt new ways of working. Safety Operations officers are often reminded of the need to translate Mine Safety Management Plans into practical safety systems during audits and inspections of mines and through investigations into accidents and incidents. To have a real effect on the mineÆs safety performance, using these systems must be a normal way of going about a dayÆs work for all persons who work at the mine: not a safety manual collecting dust on the mine managerÆs bookshelf. Mine Safety Management Plans are important to mining operators. Not only will positive involvement in the development and use of safety systems ensure they meet their obligations under mining legislation, but it will also help prevent themselves or their workmates being injured or killed.

Jan 1, 2002

Research cruises dedicated to seafloor hydrothermal activity along the Kermadec arc first began with the Sonne-135 expedition in 1998. This was followed by the worldÆs first systematic survey for venting along an arc during the 1999 NZAPLUME I expedition. Since then, cruises dedicated to mapping plumes along the Kermadec arc include NZAPLUME II (2002), NZAPLUME III (2004) and ROVARK (2007). In addition, the manned submersible cruises SWEEP Vents (2004) and NZASRoF (2005) utilised the Shinaki 6500 and Pisces V, respectively, to sample in detail select hydrothermalsystems for mineralised samples, rocks and vent fluids. The ROVARK (2007) cruise was the first to deploy an autonomous underwater vehicle (ABE) along the arc which surveyed Brothers volcano at a far greater resolution than had been done previously by ships on the sea surface. While these expeditions have largely been led by GNS Science, together with its collaborators from National Oceanic and Atmospheric Administration, Pacific Marine Environmental Laboratory (NOAA/PMEL), significant contributions have been made by other groups from various nations, exemplifying the global interest in seafloor hydrothermal activity associated with intraoceanic arcs. This is an ASTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Over the last 20 years the mining industry has played a key role in the further development of many Central Queensland and New South Wales communities. The number of people who are employed by the coal mining industry, the number of transient residents, shift work and the town facilities have all contributed to how the community views the coal mining industry. As the coal mining boom continues and the mining communities continue to grow more emphasis is needed to address the community concerns, specifically the socio-economic and environmental impacts that the coal mining companies may have on these communities. Central Queensland coal mining operations are situated in the Bowen Basin. Many of the towns in the region have been developed specifically for the coal mining industry with 13 - 50 per cent (Australian Bureau of Statistics, 2006) of people living in the communities being directly employed by the mines. The introduction of shift work, differing rosters and the mining boom have resulted in considerable changes to these communities with more transient contractors and permanent employees taking up residence outside of these communities. This change, however, has not been as noticeable in the Hunter Valley region. The Hunter Valley, situated in the Sydney Basin has two main mining towns, Singleton and Muswellbrook. Of the 37 173 (Australian Bureau of Statistics, 2006) people that reside in the communities 13.8 to 16.5 per cent (Australian Bureau of Statistics, 2006) are employed directly by the mines. The Hunter Valley is a large tourist destination due to its many vineyards; this results in a diverse community where mining is not the sole means of employment. Similar to Central Queensland the mining boom has brought more people to the Hunter Valley region, although greater percentages have taken up residence in the communities. The views vary between the two regions on the coal mining industry, specifically on the socio-economic and environmental impacts that the industry may have on the surrounding communities.

Jan 1, 2008

Historic mining across the Bendigo goldfield reached an average mining depth of 750 m over an area of about 16 km by 4 km, with two shafts exceeding 1400 m. Mining ceased in the mid 1900s due in part to increased dewatering and ventilation demands. Water extraction technology of the day, combined with multiple mine ownership, did not allow uninterrupted and thus economic mining activity to prosper. Today Bendigo Mining Limited (BML) is targeting gold-bearing reefs beneath the water-filled historic mine workings. To ensure mining activity can proceed without the risk of water inrush, historic workings are being dewatered by submersible pumps in historic shafts and through a series of underground drain holes intersecting old workings. Due to the high heads involved, individual drain hole development requires rigorous safety control implementation and assessment prior to drilling. Water extracted via drain holes is pumped to the surface through a series of pipe lines and rising mains in conjunction with two staged pumping stations. Both stations are equipped with high-speed centrifugal pumps, each capable of pumping 40 L/s at a static head of approximately 300 m. BML, which operates beneath and within a large city, is confronted with unusual environmental and social challenges compared to many within the mining industry. The raw mine water, which contains elevated salt levels, is piped through residential areas and must comply with strict controls to prevent impacts on the surrounding environment. The final delivery point is BMLÆs water treatment plant at the north end of the city. The water treatment plant utilises chemical pretreatment and reverse osmosis. It is able to process 7 ML of mine water per day at full production. The product is approximately 5 ML of reusable irrigation quality water, which is made available to the Bendigo community for public gardens, sporting facilities and rural irrigation. The 2 ML of brine is directed to a purpose-built evaporation pond facility located 7 km north of the water treatment facility.

Jan 1, 2008

By Brown GA

Results are presented which demonstrate the feasibility of employing electrolytic membrane technology to process leach liquors derived from alkaline pressure leaching of scheelite concentrates and to recover and recyle sodium carbonate. Thus the problem of disposal of sodium sulphate is avoided. In a further application of the technique sodium tungstate is converted to tungstic acid which can be further processed by three possible routes to crystalline or amorphous tungstic acid or tungsten powder. In each route sodium hydroxide is produced which on carbonation can be recycled as soda ash to the pressure leach stage. Further testwork is required to determine long term operational conditions in the membrane cell and to confirm the effect and deportment of impurities on products. The process has been patented.

Jan 1, 1986

By Baker G

The detailed mineral composition of the lead-zinc ores at Captain's Flat was first studied in 1942 (Edwards, 1943).At that time the workings did not extend far below the 750ft. level. Since then development has been extended to the 1,390ft. level, and -at the request of the management of Lake George Mines Ltd., an examination of the ore from the deeper levels has been made as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.This account is. based on that examination (Mineragraphic Rept. No. ,537, C.S.I.R.O.)GENERAL GEOLOGYThe geology of the Lake George Mines has been described briefly in The Geology of Australian Ore Deposits (1953), and in much greater detail in an unpublished report by K. Glasson (1952). The area consists of fossiliferous Upper Ordovician sediments overlain by volcanics (Kohinoor VoJcanics), and by fossiliferous Silurian sediments. The volcanies comprise a series of· flows ranging in' composition from dacite to rhyolite, with interbedded tuft's and shale lenses.The region has been strongly folded. The regional strike is from 340° to 355°, and dips are from 75°W. to 75°E, A major syncline, pitching 200 N., occupies the centre of the area. The Kohinoor Volcanic'l outcrop as two bands which represent the east and west limbs of this syncline.The Volcanks in the western limb, with whIch the orebodies are associated, are more strongly sheared than those in the eastern limb.

Jan 1, 1953

The Broken Hill (BH) Block contains a wide variety of mineralization, with comrodities including Pb, Ag, Zn, W, Cu, Co and Sn. Much of the mineralization is stratigraphically controlled. Fe, Cu and Co-rich mineralization is dcminant in the Thackaringa Group; Pb, Ag, Zn and W is dcminant in the BH Group and Sn mineralization is present above the BH Group. Some mineralization occurs as concordant syngenetic deposits, but other types have been partly or completely remobilized by metamorphism, magmatic activity or hydrothermal fluids. Almost all of the non-syngenetic mineralization, including stratabound, vein and intrusive-related types, has formed from the "recycling" (remobilization and redeposition) of metals originally deposited with the sediments and volcanics of the Willyama Supergroup.

Jan 1, 1983

By Ehlert G, Steinlechner E

The paper describes a new process for filtration which combines the continuous operation of conventional vacuum filters with the low final moisture contents hitherto only achievable with plate and frame presses. The increasingly high portion of fine particles causes several problems in the filtration of copper concentrates. One drawback is that remarkable quantities of liquid are attached to the very fine particles because of their specific surface area. Furthermore, fine particles also reduce the size of the capillaries in the filter cake, thus increasing the critical pressure which any filtration system has to exceed to achieve the desired final cake moisture. The maximum filtration pressure of conventional vacuum filters is limited by nature itself and by practical aspects to approximately 0.75 bar. The hyperbaric filter combines the continuous operating principle with an increase in filtration pressure of up to 6 bar simply by placing the entire disc or drum filter inside a pressure vessel. The major machine components and process features are explained in the details of the paper. After extensive research and field testing, 23 ANDRITZ hyperbaric filters, with a total filtration area of 1968 m2 have now been sold. Seventeen of these units (1440 m2) are in commercial use and more units are, on order. Performance data on copper concentrates from plants in Australia, South America, Poland, Africa and North America are outlined in detail. Compared to vacuum filters, generally hyperbaric filters will reduce the final cake moisture of concentrates with 75 per cent

Jan 1, 1993

By Sloan GJ, Lysnar RD

Since the of Bergstrand's Geo-dimeter in 1946, and Wadley's Tellurometer in 1956, there have been numerous Electromagnetic Distance Measurement (EDM) instruments produced throughout the world by a variety of companies.This form of measurement has not merely replaced other methods of measurement, but has caused considerable change of emphasis in survey techniques. Major control surveys are now being accomplished using trilateration instead of triangulation. The surveying of open cuts or engineering work may be done in a fraction of the time and, in the majority of cases, to a greater degree of accuracy than with older methods.It is surprising that with this new tech-nology and development of EDM equipment which is compact, easy to use and no longer so expen-sive, no advance has been made in underground surveying. If we look at equipment being used by the majority of mining companies, we see that there have been very few changes since the Second World War. Very little research has been carried out to enable the surveyor to do his work more easily in conditions which, at the very least. are hazardous.

Jan 1, 1984

By J Vann, S Jackson, O Bertoli

Ordinary kriging and non-linear geostatistical estimators are now well accepted methods in mining grade control and mine resource estimation. Kriging is also a necessary step in the most commonly used methods of conditional simulation used in the mining industry. In both kriging and conditional simulation, the search volume or ækriging neighbourhoodÆ is defined by the user. The definition of this search can have a very significant impact on the outcome of the kriging estimate or the quality of the conditioning of a simulation. In particular, a neighbourhood that is too restrictive can result in serious conditional biases. The methodology for quantitatively assessing the suitability of a kriging neighbourhood involves some simple tests (which we call æQuantified Kriging Neighbourhood AnalysisÆ or QKNA) that are well established in the geostatistical literature. The authors argue that QKNA is a mandatory step in setting up any kriging estimate, including one used for conditioning a simulation. Kriging is commonly described as a æminimum variance estimatorÆ but this is only true when the neighbourhood is properly defined. Arbitrary decisions about searches are highly risky, because the kriging weights are directly related to the variogram model, data geometry and block/sample support involved in the kriging. The criteria to look at when evaluating a particular kriging neighbourhood are the following: the slope of the regression of the ætrueÆ block grade on the æestimatedÆ block grade; the weight of the mean for a simple kriging; the distribution of kriging weights themselves (including the proportion of negative weights); and the kriging variance. Outside of the technical geostatistical literature, there is little in the published domain to describe the nature of QKNA and no practical presentation of case examples. In this paper we attempt to redress this by setting out the calculations required for QKNA and defining some approaches to interpreting the results. Several practical worked mining case examples are also given. Finally some comments are made on using the results of QKNA to assist with block size selection, choice of discretisation and mineral resource classification decisions.

Jan 1, 2003

The extraction of the values from gold bearing clay or clayey ores has always presented difficulties. A description of the successful operation of a mill working on material of this nature is here given in the hope that it will be of interest to mining engineers and metallurgists, particularly as the ore body referred to has been worked out. The methods finally adopted were evolved at the mill after the failure of 3: plant specially designed in England and sent out to New Guinea to cope with the clay by the old principle of calcining to brick followed by crushing and cyanidation. A description is given of the direct cyanidation of run of mine ore in '90 ton vats; which was finally adopted after a great deal of study and experiment. Mention is also made of the method of removing overburden in the open cut and the mining and transport of the ore from the open cut to the mill. The purpose of the paper is to record these matters while the information is still available. . .DESCRIPTION OF THE ORE BODYThe values occurred in a flat-lying lode which had slipped about half a mile down the mountain side and had come to rest in the nearly horizontal position in which it was found and worked. The thickness of the deposit varied from a maximum of about 25 ft. at the northern end to about 10 ft. at the southern end. The ore body was capped with an overburden of decomposed breccia and porphyry of variable thickness the maximum being about 65 ft. The underlying rock, or the footwaIJ of .the flat ore body was breccia locallyknown as blue breccia.

Jan 1, 1951

Porgera is located in the Central Highlands of Papua New Guinea. Porgera Joint Venture treats a high grade epithennal gold deposit. Most of the gold occurs as submicroscopic particles in a sulphide matrix although there is some quite coarse free gold. Anticipated gold production is 900 000 oz per year for the first six years of operation.Stage I of the treatment plant consisted of a concentrator and leach/CIP Circuit. It was commissioned in August 1990. Design throughput was 1500 tpd with an anticipated gold recovery of 60 per cent. Throughput achieved was actually 1850 tpd with an average gold recovery of 69 per cent. CIP tails were accumulated in a pond awaiting retreatment by pressure oxidation.

Jan 1, 1992

A survey of derelict and active alluvial tin and sapphire mines in the Emmaville area of northern N.S.W. as the first step in a pro- gramme of similar surveys to be undertaken throughout the State by the State Pollution Control Commission is presented. Thirty nine individual mine sites in the study area were included in the survey and an assessment made of the current level of impact on the environment at each site by assigning values of "magnitude" and "importance" to a number of impacting factors. Results are pre- sented in matrix form and mine sites ranked in order of impact "importance". Examples of alluvial tin, underground tin/arsenic and alluvial sapphire operations are discussed in detail and rehabilitation programmes proposed for implementation.

Jan 1, 1976

By Shinnosuke U, Zhang HE

In this paper, it is shown that the higher the pre-activation concentration of copper ions in pulp, the larger the adsorption amounts of copper ions and xanthate on arsenopyrite surface, and the better the arsenopyrite flotability in strong alkaline medium. On arsenopyrite pre-activated with cupric ions, the xanthate adsorption density in strong alkaline medium is approximately equivalent to that of cupric ions. It is therefore concluded that an amount of copper ions adsorb on arsenopyrite surface first, and then an amount of xanthate can (and only can) adsorb dependently on the surface active sites produced by these adsorbed copper ions on the mineral, so that arsenopyrite is kept rather flotable and is hardly separated from pyrite even in very strong alkaline medium. Selectively wiping out the surface copper active sites on arsenopyrite is the key point of successful separation of pyrite from arsenopyrite. According to this theory, a new 'SZLI' (know-how) method was recommended to satisfactorily deal with the difficult separation.

Jan 1, 1993

By B Roach, P M. Ashley, B Hooper

Mineral occurrences of the Hillgrove Au-Sb-W district are hosted in late Palaeozoic polydeformed, hornfelsed metasediments and Permo-Carboniferous granitoids of the NewEngland Orogen. In excess of 204 individual occurrences have been identified to date with the mineralisation developed as strike extensive (>20 km of known veining) and potentially depth extensive steeply dipping fissures. These are contained within an elongate area measuring some 9 km by 6 km in surface dimensions. Recorded gold production of 720 000 ounces along with current resources in the order of 340 000 ounces highlight the significance of this district. Historical antimony production is estimated at in excess of 50 000 metric tonnes. Significant tungsten of over 2000 t in the form of scheelite has also been produced from the field. Mineralisation is developed in veins, vein breccias, sheeted veins, network stockworks and as alteration sulfide haloes to the main structures. The vast majority of fissures are subvertical and vary in widths of up to 20 m in places. Paragenetic studies have previously indicated that the earliest mineralising event was a scheelite-bearing phase of quartz veining. Subsequent phases of arsenopyrite-pyrite-quartz-carbonate veining were accompanied by gold and minor base metal sulfides. Alteration is typically sericite-ankerite-quartz. Overprinting stibnite-quartz veining with gold-electrum, aurostibite and arsenopyrite form an important subsequent phase. Veining can be inferred from historical records to extend for vertical depths of over 1 km.

Jan 1, 2004