Search Documents

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

The mineral resource that a mining company has access to, represents the majority of the embedded value that exists within the company, as well as the competitive advantage that the company has over its peers. However, the real value is only realised once effective mining plans have been put in place, which optimise the extraction of the resource, and add measurable value to the company. The concept of mineral resource management (MRM) has been developed in South Africa, to ensure this optimisation happens in an integrated and quantifiable manner, such that value is added and risk is reduced, resulting in bottom line improvement for the stakeholders of the business. This paper describes the process of mineral resource management, and draws on successes and failures of various companies, to illustrate how it should be implemented, and what measures should be put in place to ensure its success. This requires a fundamental re-appraisal of the way in which mining companies plan and execute their businesses, and focuses attention on real value adding activities and behaviour through the use of economic value added as an appropriate metric by which to measure real value and risk. Specifically, the paper focuses on these aspects as applied to planning models and processes, exploration activity and risk management, to ensure operational and project success.

Jan 1, 2006

By Nekitel S, Arumba J, Kopi G, Findlay RH

The Kainantu area lies within the composite Scrapland terrane which is composed of Mesozoic metamorphic and intrusive units, overlain by Cenozoic marine sediments, volcanic and intrus-ive units and Quaternary fluvial sedi-ments.Four deformations (Dl, D2, D3, D4) are recognised within the Mesozoic sequences, which consist of greenschist to amphibolite facies schist derived from felsic to intermediate pyroclastic rocks and pelitic sediments. The second, third and fourth fold events are present in the Cenozoic sequence, and these rocks are broken by thrusts related to northwest trending D3 folds. South-dipping, possibly lystric, normal faults are recognised and may be related to uplift and exposure of the metamorphic rocks as core complexes.Known mineralisation in the area consists of gold and copper skarn deposits, porphyry copper deposits, shear-hosted gold deposits, epithermal vein deposits and gold placer deposits. Over 35 hard rock and 18 gold placer deposits are known within the area. Of significance are the Kathnell shear-hosted auriferous quartz veins; such structurally controlled veins may be more widespread than proposed prev-iously and offer a new exploration target.

Jan 1, 1994

Having worked as a consultant for most of his 40-year working life, mostly as a mineral property valuer, the author has seen many poor valuations. Most were valuations of exploration tenements where the selection of the rather subjective, but necessary, geological inputs raised the main concerns. Those valuations involving iron ore prospects raise particular problems due to the special characteristics of such deposits. Iron ore is more like an industrial mineral rather than precious or base metals and Reserves are determined not by a traditional cut-off grade but by customer specifications. This is intended to be an overview/keynote paper on the current state of the growing (yet consolidating) Australian Iron Ore industry. It has now moved beyond Western AustraliaÆs æPilbara Big TwoÆ of Rio/BHPB (with the emergence of the irrepressible FMG and Hancock Prospecting) to include the YilgarnÆs æMidwest ManyÆ (including US re-entrant Cleveland Cliffs through Portman) and projects in other States. Ore types have moved from haematite Brockman to martite-goethite Marra Mamba (including the RobeÆs mesas and below water table Yandicoogina CIDs) and magnetite ore types. There are DSOs and secondary process feed. Mineral valuers have to reflect today upon these and many other determinants of value when choosing the most appropriate methodologies to adopt when technically assessing and valuing exploration tenements containing iron ore. Set against a frame work of the JORC Code (2004) and VALMIN Code (2005), the general valuation issues involved in using the cost methods (eg multiple of exploration expenditure), market methods (eg comparable sales, rules-of-thumb and joint venture terms) and income methods (eg synthetic discounted cash flow (DCF)/net present value (NPV) modelling) are discussed. Relevant factors when valuing iron ore properties are discussed, eg ore type, lump/fines ratio, stripping ratio, water table, impurities and grade, particularly the JORC confidence category of the identified mineralisation. Remoteness and access to existing rail infrastructure is a key consideration.

Jan 1, 2007

By King MN, Travis IC

PISCES - the Planning and Information System for Coal Export Services has been developed by Port Waratah Coal Services (PWCS) to ensure the efficient and economic operation of the Hunter Valley Coal Chain. PISCES is a computer based integrated information and management system to coordinate operations commencing at minesites through the coal chain to shiploading at the Port. The PISCES system comprises a central database around which a number of planning modules interact. These include interactive programs for train planning and timetabling, stockpile management, berthing analysis and a coal shippers enquiry system. PWCS has previously developed - number of computer based systems for planning, controlling and monitoring complex coal handling operations and the extension of the PISCES system to the Hunter Valley Coal Chain is another initiative to assist the Hunter Valley Coal Export Industry in looking confidently towards the Future.

Jan 1, 1987

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

The Mineral Research Centre is located at Perth in the suburb of Waterford, adjacent to Curtin University of Technology and within a Technology Precinct which includes Technology Park. The Centre, constructed by the WA Government at a cost of $16 million and occupied in late-1994, comprises three separate buildings housing the CSIRO Division of Minerals, Curtin University's School of Chemical Engineering and the Mineral Processing Laboratory of the Department of Minerals and Energy. The emphasis on R&D at the Centre is primarily in hydrometallurgy as a result of staff expertise, extensive bench and pilot-scale facilities, track record with the industry and, very importantly, two of the occupiers being partners in the AJ Parker Cooperative Research Centre for Hydrometallurgy. Staff in the Centre have a long involvement with R&D agencies such as AMIRA and MERIWA. The hydrometallurgical focus of the Centre complements that of pyrometallurgy at the GK Williams CRC in Melbourne and the Centre for Mining Technology and Equipment in Brisbane, to ensure that the mineral processing industry in Australia has access to a complete range of expertise and facilities to serve its needs.

Jan 1, 1996

The term æindustrial mineralsÆ covers a wide range of minerals, from diamonds to silica sand, which are fundamental to the sustainability of a wide range of industries, from drilling mud to autocatalysts. The paper commences with an overview of the industrial minerals markets, with particular reference to the characteristics that impact on the development of a successful marketing strategy. This is followed by the identification of the steps to be taken in the negotiation and execution of an industrial minerals sales contract, from identification of the appropriate product through negotiation of the contract to ongoing customer relations. An understanding of your customerÆs business is fundamental to a mutually successful long-term relationship with that customer. The paper concludes with an overview of the techniques and approaches through which such a relationship may be achieved and maintained.

Jan 1, 2006

By Hughes A

Nchanga Division of ZCCM has installed and operated a trolley assist system on part of their truck fleet for some three years. This paper examines how the system came to be chosen and how the many features of construction and operation were dealt with. The economics and productivity of the system are presented as are the personnel aspects of acceptance and training. Zambia Consolidated Copper Mines is a state controlled copper mining company formed by the amalgamation of the former Nchanga Consolidated Copper Mines and Roan Copper Mines. The company operates seven copper mines the largest producer being the Nchanga division, which is scheduled to produce some forty-two percent of Zambia's copper production. The division operates four open pits and an underground mine which produce annually some 192 000 and 96 000 tonnes respectively of copper contained in ore.

Jan 1, 1986

By Restarick CJ

A compound cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone, has been used for coal slurry sizing experiments in the range approximately 100 to 300 micrometres. An important feature of the system is the ability to adjust the cut size of the separation over wide limits by adjustment of the flow control valve. Results have been compared with typical fine screening operations. Under roughly equivalent conditions the compound cyclone system can achieve better elimination of extreme fines, but is not as sharp as the screen for coarser size cut-off. Simulations of systems involving combinations of the cylinder-cyclone system with screens indicate that the advantages of both sizing devices can be combined to yield accurately sized products for fine coal cleaning, at much less cost than using screens alone.

Jan 1, 1984

By Houtgraaf M

The Far Fanning gold deposit is situated 60 kilometres south-west of Townsville (Fig. 1). Previous recorded production is 3756 tonnes returning about 1600 ounces of gold. This has been taken from surface and shallow underground workings- scattered over the strike length of the deposit of 1700 metres. The main production period was from 1895 to 1908.Previous exploration involving extensive trenching and sampling has been: carried out intermittently. since the 1930's, by Gold Mines of Australia (1932), Placer (1974), Anaconda (1975), Marathon (1980-8-1), Aberfoyle (1981-82), and The Northern Queensland Company (NQC) (1983-present).In 1980 Marathon undertook an extensive drilling programme to test the oxidised mineralisation. Over 200 percussion holes and- 7 diamond holes were drilled along traverse lines spaced 29 to 103 metres apart covering a strike length of around 1800 metres.

Jan 1, 1986

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993

By Rankin W. J

Increasing concern with the emission of sulphur dioxide from smelters and roasters has caused renewed interest in processes which can use waste sulphur dioxide, such as the sulphation of nickel laterite ores. The process described here proposes to by-pass the production of sulphuric acid and react laterite directly with a sulphur dioxide containing atmosphere. A thermodynamic analysis identified operating windows in which nickel sulphate forms while iron oxide (the major impurity in most laterite ores) remains stable. The initial assumptions included unit activity of all species except nickel oxide. The lowest possible nickel oxide activity (while maintaining selectivity) increased with increasing temperature, indicating that selective sulphation is favoured by low temperatures. The temperature of interest was found to be between 500 and 800¦C. Calculations show that a feed gas containing ten per cent SO2, five per cent 02, balance N2 requires a temperature greater than 650¦C for selective sulphation of nickel. Laboratory experiments showed that the assumption of unit activity of ferric sulphate was unrealistic above about 680¦C due most likely to the formation of solid solutions which decreased the ferric sulphate activity. Results are presented which illustrate the limiting equilibrium sulphur trioxide partial pressures at 700 and 730¦C below which selective sulphation occurs. Cobalt extraction was usually between 80 and 95 per cent under conditions yielding selective sulphation, whilst nickel extraction was about 50 to 75 per cent depending on temperature and choice of upper limit of iron extraction. An operating diagram is presented for a limonite ore and shows that the optimum reaction conditions are 680¦C and an input gas containing 20 per cent SO2. Under these conditions nickel, cobalt and iron extractions are 73, 95 and two per cent respectively.

Jan 1, 1996

For several years, the Geology Department of the University of Canterbury has hosted a series of postgraduate projects in the field of coal studies, supported principally by the Ministry of Energy and to a lesser extent by private companies. These projects have involved mainly West Coast Coalfields, and my own studies have focussed on inorganic geochemical aspects of West Coast coals. Because of the large number of potentially important analyte elements in coal, and the wide diversity of coals occurring in the West Coast region, this project has required a substantial amount of work to be spent on sample collection, sample preparation, development of analytical methods, and actual analysis. Considerable problems must be faced at the sampling stage: Can sufficient information be obtained from whole-seam composites, or should seams be sampled in plies. Ply analysis is preferable, but results of proximate analyses are usually available for composites only. Where multi-seam drillhole samples become available (eg Greymouth Coalfield, where some holes yielded more than six sampled seams), the ply option involves a dramatic increase in the number of samples. I have attempted to strike a workable compromise between geographical coverage of coalfields, and detailed sampling of individual seams at each locality. In many cases, sample material has been used jointly with Jane Newman who has carried out petrographic studies.

Jan 1, 1985

By P K. M Mazzoni, D Frantois-Bong

This paper aims to show alternatives to the estimation methods used for finding the parameters in GyÆs well known model for sampling variance in the case of particulate materials. Many experiments designed for gathering data on the sampling variance for specific mineral deposits allow the experimenter to use approximations in the calculation of the parameters of the mathematical model involved, which sometimes can be very useful. However, there are some instances where approximations lead to biased estimates of the parameters, and consequently, lead to errors in the establishment of the sampling protocol and treatment of quality control data. In the present work, an alternative is presented for computing the parameter values based in any experimental set up, without the need for any simplification. The method was derived using the method of least squares and evaluations are made using the usual tools in this kind of methodology: residual analysis and evaluation of the fit by means of a plot of calculated versus experimental variances. With the aid of these tools, one can better evaluate the structure of the experimental errors in such applications, and the adherence to the proposed model. In addition, it is possible to perform hypothesis testing for the equality of different sampling procedures in terms of sampling variance. The full mathematical details are given, together with an algorithm for applying the method, which can be implemented easily using any computer language. An illustration of the method is shown, considering the international work done in ISO/TC 102. This example is a determination of the minimum sample mass to be collected in iron ore shipments, in order to achieve a specified sampling precision.

Jan 1, 2005

By Young D. R, Webb I. D

The hydro-chlorination of Fe2O3 and Fe304 has been investigated in the range 850-950¦C in order to elucidate the role of iron in the segregation process for nickeliferous laterites. The kinetics of Fe203 chlorination using 20% HC1 - 80% N2 gas mixtures is consistent with a single-stage structure control model, whereas Fe3O 4 exhibits a two-stage reaction mechanism. Oxygen potential measurements using a CSZ probe located above the bed and X-ray powder diffraction results confirm the proposed reaction scheme. When a serpentine nickeliferous laterite (1.03% Ni - 11.7% Fe) was chlorinated at 900¦C with a 20% HCl - 80% N2 gas mixture it was found that the iron oxide in the ore was extracted in a similar manner to the synthetic iron oxides. Also, it was found that the nickel extraction from the ore paralleled that of the iron and the tests indicated that for the major part of the extraction, the solid nickel species were in equilibrium with the gas phase. The recovery of nickel from laterite ores by the segregation process has been investigated by a number of workers and several extensive reviews of the literature associated with this field have been published (Iwasaki, 1972; Canterford, 1975; Wright, 1973).

Jan 1, 1987

As near-surface underground mines progress deeper, the inevitable question is whether to convert from truck haulage to shaft hoisting. The desire to defer capital expenditure frequently delays investigation of the shaft option, or deferral of a decision to start shaft sinking, unless the shaft option is clearly significantly better than trucking. By the time increasing depth makes trucking uneconomic, there may then be insufficient resource remaining to justify a shaft, and the mine must close. However, had the shaft been built earlier, its lower operating costs would have permitted the mine to continue to greater depths. This paper presents a methodology for investigating the shaft versus trucks decision. As well as the typical analysis of which option is preferable at the time the analysis is conducted, the process presented illustrates how the timing of the decision to sink a shaft is critical. The paper shows how to identify the latest date at which the decision to sink a shaft can be made, after which time the shaft option will not be economic. It also illustrates how to assess the resource that may be required to justify the shaft. Considering this in conjunction with the latest decision date, implications for the companyÆs exploration program are discussed.

Jan 1, 2005

Victorian brown coals occur in massive deposits, the quality of which is determined in the first instance by means of samples taken from exploratory bores. As a number of important utilisation characteristics are connected, not with the relatively homogeneous organic mass of the coal, but with minor components such as the ash content and particular constituents of the ash, it is necessary to know how bore samples relate to coal finally used in the process concerned. Tests are described in which the statistical parameters associated with bore sampling, operational sampling and sample reduction and laboratory procedures including a range of coal analytical methods were determined. These indicated properties where analytical errors were relatively high and where sample reduction procedures contributed substantially to imprecision in results. They also showed the effects of the non-homogeneity of brown coals with higher than normal ash contents. A further experiment explored the relationship between samples taken at various stages in the course of test boring, digging, and burning a defined 'block' of coal, and demonstrated an apparent increase in the proportions of adventitious mineral constituents as the 'intensity' of sampling Increased.

Jan 1, 1976

The management of safety has undergone a number of radical changes in the past 100 years. The most important paradigm shifts occurred through the work of Heinrich, followed by the advent of the safety systems era and, more recently, the behavioural safety approaches that have become increasingly popular around the world. Each of these æapproachesÆ to safety has left an indelible mark on the way we target safety improvements, helping decide which interventions are deployed and how they will be measured. They have also resulted in a number of æmythsÆ about safety management, each of which will be discussed, analysed and challenged in this paper. This paper highlights the complex problem of æcomplacencyÆ, that has arisen out of the increased levels of regulation and consequent perceived protection that workers enjoy in the work place. It also looks at a phenomenon called æaccident migrationÆ which results from a superficial treatment of accidents with changes to rules and procedures. The most recent approach to safety is generally known as behaviour-based safety, which flowed from the human sciences and quality management era. This approach has had a dramatic impact on the way safety is managed around the world, but still falls short in a number of key aspects, most notably the area of risk awareness and risk understanding. Many workplace accidents occur simply because the risk is unidentified, underestimated, not understood or ignored. This paper proposes a new direction for safety, called competency-based safety. It is based on cognitive psychology aimed at combating the consequence of modern protection. A case study is presented detailing the deployment of this approach throughout Placer Dome.

Jan 1, 2005