Search Documents

By A Bird

Gravity gold circuits have an important part in reducing operating costs and maximising recovery in modern gold plants where coarse gold is present in the ore body. The design and selection of equipment has a vital part in the overall effectiveness of the gravity gold circuit. There are a number of associated factors that need to be taken into consideration when selecting the most suitable equipment for gravity gold circuits including occupational health and safety, security and labour requirements. This paper is a case study that outlines the validation behind the design, selection of equipment and subsequent benefits of the recent upgrade of the gravity circuit at the Marvel Loch gold mine with the main component to the upgrade being the installation of a Consep Acacia Reactor. Since the upgrade there has been a significant increase in gravity recovery, which has reduced the amount of gold reporting to the leaching circuit therefore reducing reagent consumption and overall operating costs. There has been an increase in overall gold recovery and therefore increased gold production. The benefits to occupational health and safety include the removal of toxic gases being released in the gold room during the previous practice of gold concentrate calcination and the removal of the arsenic and nickel from the gold doré, which poses a risk during refining. Manual handling and security has improved as there is no physical contact with gold concentrates during the automated process using the Acacia reactor. The total time for gold room personnel working in the gold room has also reduced from around six hours per day to less than one hour per day.With the continuing development of low grade gold deposits, there will be an increase in demand for low capital, high recovery gravity gold circuits that can significantly increase overall production while reducing operating costs.

Aug 8, 2011

By D Mather

Fibre reinforced shotcrete has long been accepted as temporary ground support in both mining and civil tunnel linings. Greater knowledge and understanding of shotcrete as an engineering material and advances in its quality have enabled designers to eliminate the requirement of a second pass lining. The initial shotcrete can be used as the permanent tunnel lining or be incorporated into the final lining design, rather than ignored and considered as sacrificial.For the initial shotcrete lining to become a suitable permanent tunnel lining it must be able to establish and maintain stability over time when subjected to all possible loads. To ensure this, best engineering practices are required during the design phase of the project to analyse; ground conditions including rock mass properties, ground and ground water quality, rock mass loadings, excavation sequencing, and construction methodologies.The increased durability of steel fibre reinforced shotcrete over traditional tunnel support, in the right ground conditions, makes it possible to achieve a serviceability design life of greater than 100 years (as required in most infrastructure projects). By specifying a good quality shotcrete mix and ensuring adequate quality control for batching, fibre dosing, preproduction testing, excavation sequencing, and application control, it is possible to eliminate the requirement of a secondary lining. The properties of a suitable permanent lining must be well established using suffi cient preproduction testing in combination with post application monitoring.A major benefit of steel fibre reinforced shotcrete in ground support applications is the removal of any requirement for workers to work under unsupported ground. Its use can also significantly reduce, if not eliminate, the manual handling associated with placing traditional reinforcement such as lattice girders and mesh. Both of these benefi ts are significant with the ever increasing focus on health and safety.This paper highlights factors that must be considered in the design and specifications to enable an initial shotcrete tunnel lining to become the permanent shotcrete tunnel lining.

Mar 8, 2011

By C A. Foss, K Blay, K Leslie, D Hillan

Magnetic field studies provide remote sensing of magnetisation distributions and a means to investigate moderately- to strongly-magnetised ore deposits that may be partially or totally buried. However, above-surface magnetic field surveys have limited capability to resolve the detail of magnetisation distributions because of the large separation between the magnetisation and the magnetic sensor. While some of this detail is available from magnetic susceptibility logging within boreholes or from magnetisation studies on recovered core, these measurements are limited to the exact trace of the boreholes. The large disconnect between ground or aeromagnetic surveys and highly-localised borehole sampling can cause problems in developing robust source models from magnetic survey data. The measurement of magnetic field in boreholes has the capacity to at least partially bridge that gap by measuring the magnetic field due to magnetisations proximal to, but not intersected by, the boreholes.CSIRO has developed the world’s first downhole magnetic tensor gradiometer. This instrument measures magnetic field gradients in all directions within a borehole. A prototype instrument has been built and tested as part of phase 1 of the Deep Exploration Technologies Cooperative Research Centre (DET CRC). The prototype performed well with magnetic pyrrhotite at the DET CRC test site in the Adelaide Hills and at Carpentaria’s Hawsons magnetite deposit south of Broken Hill. Further work is required to reduce the diameter of the probe so that it can operate in NQ holes (it is currently limited to HQ or wider) and to transform it to a continuous logging tool. The borehole tensor gradiometer can be used to investigate the continuity of magnetisation over a distance of several metres to tens of metres away from a borehole intersection and the structural dip of the magnetic body. It can be used to either replace or augment downhole magnetic susceptibility logging. This instrument is one component of an integrated CSIRO suite of new magnetic field utilities and methodologies for iron ore exploration and development.CITATION:Leslie, K, Foss, C A, Hillan, D and Blay, K, 2015. A downhole magnetic tensor gradiometer for developing robust magnetisation models from magnetic anomalies, in Proceedings Iron Ore 2015, pp 299–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Bruggemann, F Sereshki

There has been an ongoing research on coal and gas outburst for the past two decades at the School of Civil, Mining and Environmental Engineering, University of Wollongong. Research study began with a humble beginning, initially conducting basic laboratory studies on the coal and gas properties, progressing into the determination of gas content of coal by sorption technique and the effect of gas pressures on coal strength. The present laboratory facilities and research interests are extended to include the study of coal permeability and shrinkage properties and their effect of gas drainage characteristics with respect to gas type, and pressures. All the changes are examined with respect to changing in-site geological conditions of the coal deposit investigated. The aim is to provide a long-term support to industry in establishing a data bank for Australian coal deposit characteristics and properties.

Jan 1, 2005

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

By S Oliver, D Willingham

"Although a resource model is central to the mineral resource value estimation process (Glacken and Snowden, 2001), creating it is a labour intensive task and in the end it is a limited representation of the actual orebody. Creating this resource model is a labour intensive task that requires inputs from geology, mining, metallurgical and commercial disciplines. It requires thousands of samples from hundreds of drill holes to be verified, grouped in geological domain, interpolated and then valued. Even after all this effort, a model is only an estimation; therefore further significant effort has gone into quantifying uncertainty in the model and subsequently risk around any value estimates derived from the model. Further risks to model quality are introduced through poorly conditioned data or incorrect assumptions.This paper proposes the application of machine learning to automate the resource model development. Machine learning is applied to the traditionally manual tasks of geological formation, domain identification and validation of the block model mineralogy. Through automation the resource estimation process can be accelerated, allowing more drill holes or a larger resource body to be processed in a given time frame, or allowing the process to be more agile to changes in input data and assumptions. A case study based on drill hole data from a Western Australian iron ore deposit (Government of Western Australia, Department of Mines and Petroleum, 2015) is used to demonstrate the application of machine learning in this process.CITATION:Oliver, S and Willingham, D, 2016. Maximise Orebody Value through the Automation of Resource Model Development Using Machine Learning, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 295–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Karlson R, Rispin M

Chemical admixtures are not commonly included in the variety of backfill mixes used in the mining industry. This may be attributed to several reasons including, but not limited to: the perceived high added cost, 2. the lack of awareness about their proper use, and 3. the lack of knowledge about their features and benefits. In the construction industry today, however, chemical admixtures are used in the majority of the concrete produced, enabling concrete to become a more cost-effective building material. They also enable construction crews to meet demands for year-round construction, quicker completion of construction projects, and improved concrete properties. The high demand for chemical admixtures in the construction industry has led to numerous innovations in admixture technology in recent years. Some of these chemical admixtures have been found to enhance the production, transport, placement, and in situ properties of backfill mixes. Others have been found to reduce the cost of such mixes while maintaining, and in some cases improving, their physical properties. In this paper, a few of such innovative admixture technologies are discussed. The benefits, imparted by these technologies to backfill mixes as well as performance data on their use in several backfill applications at various mines, are presented.

Jan 1, 1998

By G Varley

This paper describes the mining methods and strategy used to extract the 5 Orebody crown pillar at the Isa Lead Mine over the past five years. The bulk of the crown pillar was extracted by the use of sublevel open stope method. An uphole bench stope was mined to scavenge the remaining ore. Geomechanical issues associated with the crown pillar extraction are described. Stope sizes were gradually increased on a stope by stope basis. This has allowed the maximising of ore recovery while relevant risks were managed. The principles in designing ore rib pillars against various types of fill materials are also described.

Jan 1, 2002

By D Henderson, M Germain

The beneficiation of iron ore deposits to yield haematite and magnetite concentrates for steel making processes typically require the use of one or a combination of wet processing techniques based on gravity, magnetic or froth flotation processes. With the need for more cost-effective technologies with a lower water demand, a re-examination of dry processing techniques has been initiated. For example, a dry processing capability may offer an advantage where suitable quality and quantity of process water hinders the development of a particular resource. This paper describes recent laboratory test work for the production of high grade concentrates using dry electrostatic techniques for -300 ¦m haematite and magnetite ores and compares them with magnetic separation techniques.

Jan 1, 2009

By R Bertuzzi

"This paper presents preliminary results of ongoing research being carried out at the University of New South Wales Australia (UNSW) into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that rock mass strength can be determined following the geological strength-index (GSI) approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions: construction dates from 1880s to 2006 spans from 3.2 to 12.5 m depths from 17 to 124 m excavation methods of drill and blast, roadheader and tunnel boring machine (TBM).Finite element modelling is used to assess the likely magnitudes of the principal stresses that were present at the time of the failures. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zones. Failure and stable points are then compared to the proposed strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown and the spalling criteria. The ability of the Hoek-Brown rock mass strength criterion to differentiate between the ‘failed’ and ‘stable’ zones is considered to be remarkable.CITATION:Bertuzzi, R, 2014. Estimating the rock mass strength of Hawkesbury Sandstone, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By J E. Everett

Ore selection is generally a highly subjective task, with emphasis on producing product with a consistent target grade matching a perceived market requirement. A composite selection criterion ‘Comp’ (a linear function of the grade vector) can be used to maximise ore tonnage at a specified target grade (in Fe and contaminants) extractable from a block model. The blocks correspond to the selective mining units, with grades interpolated from diamond drill hole data. An iterative procedure has been developed to identify the coefficients and cut-off value for the composite function ‘Comp’, maximising potential ore tonnage at target grade.Commonly, target grade is predetermined by marketing; however, there is no guarantee that maximising ore tonnage at a specified target grade maximises the potential value of the mine. If the value of ore could be expressed as a linear function of the grade components, then these coefficients would be appropriate for the selection criterion ‘Comp’. The cut-off value for ‘Comp’ would correspond to the marginal cost of production; all blocks with a ‘Comp’ score above the cut-off would be classified as ore; and the cumulative grade of these ore blocks would be the average product grade over the life of the mine.Unfortunately, no such value function for iron ore is generally available. Methods for estimating the value function are discussed, using the spot price and sensitivities based either upon operational tolerances for Fe and the contaminants or upon published price differentials. This approach has been applied to an anonymous Pilbara deposit with about one million blocks averaging 1.1 kt. It is shown how the optimal target grade, cut-off grade and maximum tonnage can all be explored as a function of marginal cost and iron ore price. Alternatively, given marginal cost and an iron ore price, the effects of changing the tolerances (and therefore the relative costs of the contaminants) can also be explored.It is suggested this procedure can enable informed decision-making for an iron ore mine. Rather than setting final policy for the entire life-of-mine, the method enables target grades and tonnage estimates to be revised by re-computation as the mine life proceeds to recognise changes in market conditions and knowledge about the resource.It should be emphasised that this paper is concerned with ore selection rather than ore sequencing. Appropriate ore selection is a necessary but not sufficient condition for maximising value. Having identified the set of blocks that potentially maximise value, the sequence in which they are mined will present a trade-off between producing at constant grade and extracting high value ore early. The sequencing issue is not considered here. It is shown that optimum ore selection for an open pit mine is independent of any consideration of discount rates, although ore sequencing will depend upon the time value of money if the product grade is to vary across time.CITATION:Everett, J E, 2015. Ore selection to maximise value, in Proceedings Iron Ore 2015, pp 443–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By B Robertson

Over the 40 years that the author has been engaged in the Australian underground coal mining industry, there has been a continuous improvement in safety performance as the sector has grown in size and productivity. The underground environment hosts many hazards with significant risk profiles that are kept in check by effective health and safety management systems that have evolved largely following major underground disasters. Observations are made on the changes observed for specific aspects of the underground coal sector, with particular reference to ventilation issues, and predications are made as to the needs of the future.CITATION:Robertson, B, 2013. Past achievements and future challenges in the underground coal sector, in Proceedings The Australian Mine Ventilation Conference , pp 27-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By G P. F Chitombo

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have been identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

By S SSdbom

A comparison was made between chemical analysis and ocular mineral/rock classification in health-based risk assessment of historical mine waste produced between 1625 and 1975. Large parts of the mine waste are heavily weathered and secondary minerals are abundant. The field was divided into several areas from where composite samples were collected. Seventy-five mine waste samples were selected for chemical analysis (As, Cd, Co, Cr, Cu, Hg, Ni, Pb, V and Zn) and ocular mineral/rock classification (silicate, mica, granite/pegmatite, carbonate, iron oxide ore, sulfide ore, distribution between chalcopyrite, sphalerite and galena and distribution between pyrite and pyrrhotite). The waste has been produced in conjunction with mining a complex sulfidic ore with increasing iron oxide content (mainly magnetite) towards the northern part of the field. Elevated concentrations were found for Cd (average 26 mg/kg dw), Cu (average 3500 mg/kg dw), Pb (average 4100 mg/kg dw) and Zn (average 11 000 mg/kg dw). Large differences between average and median values indicated that the data was not normally distributed, ie the metals occur as discrete minerals (eg chalcopyrite, galena and sphalerite). The ocular classification indicated low carbonate content, chalcopyrite dominating over sphalerite and galena in most samples and an even distribution between pyrite and pyrrhotite. Both analytical and ocular mineral/rock classification data were combined into a common matrix that was evaluated using multivariate statistics. Principal component analysis (PCA) showed, for instance, that chromium and vanadium were mostly associated with harder minerals and rocks. PCA also indicated that a similar graphical picture could be obtained for chemical data and ocular mineral/rock classification data, respectively. The comparison indicates that ocular mineral/rock classification can replace or at least reduce the numbers of chemical analysis in health- based risk assessment of historical mine waste.

Jan 1, 2008

By L I. Rozman

"There have always been development projects that fall short of expectations. In the last decade, we have seen more than the usual number of mining and oil/gas development projects taking significantly longer to develop and costing materially more than expected. The recent resource-equity market slump proves that investors are now far more cautious about investing new capital in the mineral and petroleum resources sector.What have we learned since 2005? Why have projects missed their targets? Why do investors often feel misled?Valuation of a project and the estimation of value is a more complex process than the evaluation of the merits of project development. The merit of project development can be clear from a prefeasibility evaluation, but this is no reason to skip the rigour of a feasibility study. The valuation of any project that is developed with any added risk should be discounted for this added risk.The development of a project impacts on other stakeholders, and the indirect cost of these impacts can have material implications for the cost structure, time and ultimate valuation of the project for its financial backers. The development of new projects (and thereby supply) can also have an impact on commodity prices, and therefore an impact on returns for financial backers.This paper will provide commentary on the author’s experiences and observations as a project developer and operator for 25 years, before becoming a project financier a decade ago.CITATION:Rozman, L I, 2016. Project evaluation and valuation – an investor’s golden rule, in Proceedings Project Evaluation 2016, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By R A. Medower

This paper provides a glimpse into the future of minerals processing with emphasis on æAutomation InnovationsÆ for the new millennium, particularly those involving advanced process control and innovative new applications of process control technology in 2007.

Jan 1, 2000