Search Documents

By M Suzuki

Although several models for the surface tension of molten oxide slag have been proposed, suitably accurate predictions of this property are not yet possible. The surface tension, or surface excess free energy, of molten oxides is largely determined by the ionic coordination induced by surface relaxation. However, the associated mechanism of surface structural relaxation for molten oxide mixtures such as slag is complex and not yet fully understood. To allow a better evaluation of surface relaxation characteristics, the present work analysed the ionic coordination associated with the surface-relaxed states of several oxide mixtures. This work especially focused on calcium aluminate slags because these materials exhibit complex relationships between composition and surface tension. The effects of incorporating low concentrations of SiO2 as a surface active component on the surface ionic coordination were also examined. X-ray absorption techniques were used to assess oxygen and cationic elements in glassy samples after surface relaxation treatments, and molecular dynamics simulations based on a polarisable ion model of molten slag with vacuum/melt interfaces were also performed. The X-ray absorption techniques provided data related to electron yields (which are primarily associated with surface features) and fluorescence yields (which evaluate the bulk material). Thus, the ionic coordination characteristics of both regions were investigated. The results of molecular dynamics calculations allowed statistical analysis of the distributions of Al- or Sicentred polymorphs as well as the bond angles between cations and oxygen anions in the vacuumexposed and bulk regions in the equilibrated melt. The results indicated that bridging oxygen ions were preferentially distributed in the relaxed surface region rather than non-bridging oxygens. These bridging oxygen ions represented vertex connections between AlO4 or SiO4 tetrahedra. In the case of the calcium aluminate slags, the addition of one Ca2+ ion as charge compensation for two Al3+ ions was found to be necessary to form two AlO4 tetrahedra. This specific feature of surface ionic coordination could be responsible for the complex trends observed in surface tension data. The incorporation of low concentrations of SiO2 reduced the proportion of tetrahedrally-coordinated Al ions such that higher coordination states become dominant in the bulk of the material, whereas AlO4 tetrahedra were preferentially distributed in the surface region. SiO4 tetrahedra were the preferred Si-centred polymorph and were likely connected to one another to form bridging oxygen ions at the surface. On the basis of these results, a model to predict slag surface tension was proposed, and the energy of the formation of the ionic clusters resulting from surface relaxation was taken into account.

Aug 21, 2024

By M P. Sandy, R M. Stephenson

Portals to access underground mines are important infrastructure and their design requires careful consideration. Portals are generally expected to last for the life of the mine. Typically, the exposure of personnel and equipment is high, with many hundreds of movements through the portal per day. Consequently, the risk associated with geotechnical instability must be extremely low. Portals are often established from a boxcut. In areas where the weathering profile is well developed, the design and execution of the boxcut can involve significant effort, with the objective of minimizing the volume of the boxcut, whilst ensuring that conditions at the design depth are suitable for establishing a stable portal. Properly designed site investigations are a critical part of this process. Currently available portal design guidelines have not been updated for decades, however the equipment and ground support systems have changed significantly in recent years. Many mine portals have since been constructed in a relatively short time frame with success, often in challenging ground conditions using some of the more modern approaches to ground support. This is beneficial because delays in establishing a portal will generally delay other critical path activities, and lead to cost overruns.

Mar 15, 2021

By T E. Hayward, D H. English, S J. Smith

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

Hidden under picturesque Bemic Lake, in Canada's eastern Manitoba, lies a highly fractionated pegmatite orebody, hosting a unique assemblage of minerals. Accidentally discovered in 1929, the orebody had a brief history as a tin producer, but it is now mined by Tantalum Mining Corporation of Canada, Ltd. (TANCO), for its cesium, lithium, rubidium and tantalum bearing minerals. The mine also has potential for mbidium-feldspar, amblygonite, gallium rich mica, and quartz production. This paper describes the geology of the orebody, and its mining and processing. Selective, concurrent, mining and milling of the various products necessitates a high degree of planning and control, and these aspects are also discussed. The introduction of Quality Control and SPC are discussed, for such are the keys to excellence.

Jan 1, 1989

By T Zhao, K Wang, Z Zhang

Tailings pond safety monitoring is vital for preventing dam failures and ensuring environmental safety. Unmanned Aerial Vehicles (UAVs) can enhance tailings pond monitoring with flexible operational cycles and the ability to collect remote sensing data from inaccessible areas. While many mining operations have adopted UAVs for tailings pond management, their full potential in data acquisition and subsequent analytical processing remains largely untapped. This paper explores various case studies where UAVs have been utilised for monitoring key aspects of tailings ponds such as beach line indicators, dam displacement and erosion, slurry discharge processes, and tailings pond capacity. We also present examples where data derived from UAVs have been instrumental in slope stability analysis, seepage modelling, Tailings Dam Breach Analysis (TDBA), and risk prediction. By integrating UAV technology with traditional ground-based sensor techniques, this approach significantly enhances the precision and reliability of hazard prevention and management in tailings pond operations.

Sep 1, 2024

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Nov 8, 2021

By N J. Potter, N W. Brand, J M. F Clout

The increasing demand for iron ore with low concentrations of trace elements, puts increasing pressure on iron ore producers for high-quality material. Understanding the mineralogy, petrography, chemistry, and mineral association of iron ore deposits is becoming increasingly important to provide iron ore products that meet the ever-increasing standards of steel mills. Limited attention has been paid to documenting new orebodies beyond bulk RC drill chip assays and product specification data. Therefore, limited information is known about the spatial distribution of minor and trace elements at the hand specimen scale, and elemental deportment within different ore and gangue minerals. In this study, samples from high-grade microplaty hematite, supergene-enriched martite-goethite and hematite iron ores are examined for their elemental and mineral associations. These samples contain distinctive minor and trace element distributions, with the mapping of deleterious elements (eg Zn, As, Cu) enabling the deportment and abundance within the ore and gangue minerals to be assessed. Results from this study show a diverse range of minor and trace mineralogy that are present in typical iron ore samples, in abundances below the detection limit of routine XRD scans, that host the deleterious elements, including but not limited to, sphalerite (Zn and S), chalcopyrite (Cu and S), xenotime (P and Y), apatite (P and Ca), cryptomelane (K and Mn), barite (Ba and S), alkaline feldspar (K, Al and Si) zircon (Zr and Si) and chromite (Cr and Al). The presence of these minerals and associated deleterious elements, even at low concentrations, has implications for producers, with the ongoing restrictions and tightening of environmental constraints in shipped iron ore products. By understanding the distribution and location of these elements within the iron ore, steps can be considered to maintain increasingly higher quality iron ore supply around the world.

Nov 8, 2021

ABSTRACTFor the binary system copper-lead two relationsEquation 1andEquation 2have been derived for the activities of copper and lead at compositions and absolute temperatures within the liquid region of the phase diagram.These relations give, with greater accuracy than is given by previously published relations, the activity-composition temperature variations for all regions of the phase diagram of interest to metallurgists.These relations are essentially simple forms of the Margules equations but with linear temperature dependence applied to their coefficients. This has been done in such a manner that a phase diagram obtained from these relations agrees well with the data available for this system. The methods of obtaining the relations and constructing a phase diagram from them are both given in detail. The enthalpies and entropies of mixing are compared with those derived by other methods.

Jan 1, 1971

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By Bruington T, Perkins J, Hutton R

Natural resource developments are among the largest and most challenging projects taking place in the world. They involve capital intensive investment with long lead times and the management of geological, market, technical, operational and financial issues. A clear strategy is required to manage these projects and this strategy is underpinned by a development Philosophy.

Jan 1, 1997

By Lewis RW, Tullemans FJ, Gallo JB

Gold mineralization at Kidston occurs in a semicontinuous zone near the margin of a large, late Palaeozoic breccia pipe. The pipe is ovoid in plan, funnel-shaped in cross section and straddles a contact between Proterozoic metamorphic and granitoid rocks which are intruded by a swarm of late Palaeozoic acid dykes. Rock fragments within the breccia pipe reflect the enclosing country rocks and mix in various proportions to form gradational lithological domains. Most of the gold is free and is located in the breccia matrix and in a set of inwardly dipping sheeted quartz veins which kink around the pipe margin. Sulphide minerals, dominantly pyrite, occur as disseminations in the breccia matrix and as aggregates in the cores of quartz veins. Hydrothermal altLration is pervasive within the breccia and is most intense in areas with the highest percentage of acid dyke fragments. Sericite and carbonate are the main alteration minerals. An empirically developed genetic theory for the formation of the breccia pipe and attendant mineralization involves magmatic and post-magmatic processes associated with the intrusion of a granitoid body to a shallow level in the crust. Economic evaluation of the deposit relied heavily on the results of diamond drilling. Both polygonal and geostatistical reserves were calculated and found to be in close agreement. Geostatistical reserves are considered to more closely reflect the tonnes and grade achievable during mining. Daily geological mine routine is strongly biased towards grade control allied with the practical aspects of open-pit mining. Tonnage/ grade correlations between ore blocks geostat- istically generated from exploration diamond core results and ore blocks generated from high

Jan 1, 1986

By Holmes RJ, Sowerby BD, Watt JS

Major improvements have taken place in mineral and coal processing in the last decade. The development of nuclear on-line sensors that continuously analyse the material being processed has led to better control of metalliferous mineral processing and increased recovery of valuable minerals. The recent development of on-line techniques for analysis of coal is expected to be of similar Importance. Australian developments in on-line nuclear gauges are reviewed. These include systems for in-stream analysis of mineral slurries with comments on plant operating experience; on-line determination of ash in coal using low energy Y-ray transmission and pair production techniques; in-stream determination of solids weight fraction and ash content of coal in slurries with variable voidage; and on-line determination of moisture in coal, iron in high grade iron ores and sulphur in lead sinter.

Jan 1, 1986

By Drinkwater DJ, Watsford RMS, Johnson NW, Munro PD

This paper describes the use of modelling and simulation techniques in the analysis and optimisation of grinding circuits at the Lead/Zinc Concentrator of Mount Isa Mines Limited.The objectives of the studies were to: -1. improve primary grinding circuit performance by reducing the production of -0.006 mm galena fines.2. maximise the fineness of grind in the second existing grinding power and pumping capacitie The study has shown that quantitative models can operations. The models described plant operation,,and simulated the effect of process changes on plant performanc The use of automated scanning electron microscope technology tcliberation characteristics of the major minerals in the Mount isa Lead/Li ore is also described.

Jan 1, 1985

By M McDonald

KiwiRail has a goal of significantly improving passenger rail services to west Auckland, as part of its DART (Developing Auckland’s Rail Transport) suite of projects. The New Lynn Rail Trench (NLRT) project was a significant component of this work. The NLRT project facilitates essential doubletracking of the Western Auckland line, and provides a new commuter transportation hub within a busy town centre.The 1.5 km stretch of track through the New Lynn town centre has bisected the township for over 80 years. Double-tracking the line provided the opportunity to grade-separate road and rail, which would help to re-connect both sides of the township and enhance public amenity and safety.KiwiRail employed an Early Contractor Involvement (ECI) procurement model engaging a consortium comprising Fletcher Construction, Beca Infrastructure and Synergine to develop a Design and Construct solution.With weak soil conditions and high groundwater levels, a diaphragm wall construction method to form the trench walls was selected as the best solution. Further challenges to construction included working within a narrow rail corridor constrained by buildings along much of the boundary, and a requirement to keep the existing line open for rail services. Detailed construction planning was required to ensure rail and construction safety in a constrained space whilst building the trench walls, propping these walls during excavation, and constructing the base slab in the most efficient way possible.This paper will detail the geotechnical conditions and the additional constraints that made this rail trench a challenging structure to design. It will also describe the fi nal design and construction methodologies that were employed, that allowed very successful completion of the project.Additionally, this paper will review the design and construction lessons applicable to the current Victoria Park Tunnel project, and indeed for all future cut and cover tunnel projects in the Auckland isthmus.

Mar 8, 2011

By Thirnbeck M, Sione T, Petrie P, Leach TM, Mori W, Digan K, Harry K

Gold and lesser copper mineralisation are associated with porphyry-related vein systems periph-eral to two separate inferred intrusive centres north of Kainantu, Papua New Guinea (PNG). The intersection of NW trending structures, formed parallel to the Markham Fault, with NE trending transfer structures localise porphyry intrusions, and control vein distrib-ution.The Arakompa veins intrude pre-existing fractures in Akuna granodiorite, located proximal to an inferred porphyry. These veins are characterised by early quartz and later pyrite-chalcopyrite. Gold mineralis-ation is associated with Bi-Te phases in the sulphide veining. At Maniape, en echelon gash veins occur within the imbricate portion of a regional structure. Maniape is a high level carbonate-base metal gold system formed distal to the same porphyry source as Z ?-;4 kmmna

Jan 1, 1994

By B P. Micke

Central Norseman Gold Corporation was established in 1935 and has been mining on the Norseman field in Western Australia since then. It is Australia’s longest continuously operating gold mining operation at nearly 80 years, although it has had its periodic challenges in the intervening years.Over the last 40 years, a series of open pit mines around the Dundas Goldfield have supplied lower cost mill feed to the Phoenix Mill at Norseman from time to time but this has largely come to an end for the foreseeable future. Now that underground ore sources are once again the principal mill feed, there are several challenges to be met for an ongoing profitable operation.During the last 20 years, there have been three different owners and this has affected the manner in which the operations were managed quite significantly. These differing approaches are contrasted and examined in some detail from both the operational and financial aspects.Planning of a downsized operation to ensure sustainable profitability in the future in a mining environment where there has rarely been more than two to four years of reserves ahead of the mill for planning purposes has been a significant challenge. Several of the options examined are described, including alternatives for future mine development.CITATION:Micke, B P, 2014. Managing the margin at Norseman, Western Australia – a case study, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By K White, R Hardie, J Merritt, B Kirsch, R Lucas

Constructed stream diversions are a common element of mine sites across Australia. A review of constructed stream diversion performance in the Bowen Basin funded by the Australian Coal Association Research Program (ACARP) in 1999 found over 80 per cent of constructed stream diversions failed to meet regulator and operator expectations. Since that time, improvements have been made in the assessment, design, monitoring and management of constructed stream diversions. Fundamental to these improvements has been the development of a better understanding of the regional stream systems and efforts to replicate the natural stream processes in the function and operation of constructed stream diversions.This paper discusses the history of constructed stream diversions through the Bowen Basin in central Queensland recorded in the outcomes of a series of ACARP funded research projects. Further, the paper reports on the outcomes of a current ACARP funded project that has reviewed the success or otherwise of constructed stream diversions in the region. The assessment has compared the performance of diversions that have been designed to replicate and provide for ongoing stream geomorphic processes with those diversions that were designed and built prior to the development of these design improvements. Based on these investigations we have identified design and construction successes and issues requiring further research and management attention.CITATION:White, K, Lucas, R, Hardie, R, Merritt, J and Kirsch, B, 2013. Challenges and opportunities for constructed stream diversions in the Bowen Basin, Central Queensland, in Proceedings Water in Mining 2013 , pp 73-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By S Larbi-Bram, F Shi, E Manlapig

Mining companies have recognised that characterisation of particle breakage plays an essential role in the design and optimisation of comminution circuits. Recently the JKMRC comminution research team has developed a new breakage model incorporating the effect of particle size, and a new breakage characterisation testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions. The latter is believed to be the dominant breakage mechanism in AG/SAG mills. Existing devices, such as the JKMRC Drop Weight Tester, are not suitable for performing repetitive impacts since they are too time consuming. Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalised experimental test program on professionally designed and manufactured JKRBT machines. The first JKRBT was installed at the Anglo Research laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the project in 2008, with commercial release expected in early 2009. The JKRBT has the potential to revolutionise ore testing, with applications in laboratory impact breakage characterisation of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control of comminution circuits since it is readily adaptable to on-line ore hardness measurement. Can any mine afford to miss out on this technology?

Jan 1, 2008

By A S. Lund

Optimisation of the underground mining production process benefits from informed decision making during the process of explosive rock fragmentation. Selection of the most appropriate bulk explosive products for underground production blasting is an area of endeavour that offers significant economic upside if correctly and thoroughly undertaken. The explosive selection process is facilitated by a clear understanding of:the physical and detonic properties of the alternative explosive options available; the response of different rock masses to these different explosive options; and the importance of maintaining a clear focus on desirable blast outcomes in order to enhance value creation aspects of the mining production process. The level of understanding of these issues is raised through the application of measurement and modelling technology, quantifying the effects of blast design (and implementation) on process outcomes. Homestake Darlot and DynoConsult applied a range of dynamic blast measurement and outcome modelling techniques in order to explore the relationship between rock properties, explosive properties and mining process efficiencies. A campaign of vibration and explosive Velocity of Detonation (VoD) measurement produced feed data for use in vibration and fragmentation modelling during the extraction of one of the major stoping blocks at Darlot Gold Mine. The paper describes the use of these tools and discusses the understanding gained concerning the limitations and capabilities of, and the reconciliation between, a selection of analysis and modelling approaches.

Jan 1, 2001