Search Documents

By A Nisbett

The largest single operating loss in many hydrometallurgical plants is the poor recovery of leached product in the solids sent to tailings. Any reduction in the concentration of the valuable species in this stream will improve the project economics. Conventional design, to reduce the soluble loss, is to increase the number of wash stages or the wash/water ratio. This approach is limited in effectiveness as it can only reduce the soluble loss to that dictated by the concentration in the returning solution. For copper plants this concentration is set by the recovery in the solvent extraction (SX) plant. When using a single grade of SX feed a single grade of SX raffinate is produced generally with five to seven per cent of the copper still remaining in solution. An alternative approach has been developed by Cognis Corporation and implemented on a number of recent projects using engineering input from Miller Metallurgical Services. The SX plant feed is æsplitÆ into two different streams: a high-grade stream containing up to 75 per cent of the copper and a low-grade stream with the remaining copper. This Split-CircuitÖ concept has significant benefits in terms of both copper recovery and reduction in acid costs. The high-grade stream has the bulk of the copper removed and the raffinate sent directly back to the leach; to fully re-use the acid that has been generated during extraction in the SX process. The recycling of this higher concentrated acid stream considerably reduces the acid in the raffinate sent to washing steps. It represents a significant saving in acid consumed via the tails stream. The low-grade stream has a significantly lower SX feed grade and hence produces a lower raffinate acid and copper concentration. This lowers the economic species in the wash solution and hence reduces the soluble loss accordingly. Other operating improvements are realised with lower neutralisation costs (with the lower acid in the wash stream) and from a decreased need for in-circuit neutralisation to improve SX performance. The SX plant itself is also split into a high-grade extraction and a low-grade extraction stream to enable the low-grade raffinate to be produced. A number of circuit alternatives have been utilised that have provided a range of benefits. The circuit concept has been included into both new and existing plant operation. As a result of this experience other methods of incorporating the concept into a circuit have been developed.

Jan 1, 2005

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation: W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By D Lau

Traditionally X-ray diffraction (XRD) has not been significantly used by the cultural heritage sector, as the most commonly used technique, X-ray powder diffraction (XRPD), requires sample removal from the artwork or artefact, followed by grinding of the sample to a fine powder. With the development of micro-X-ray diffraction (micro-XRD) and other associated advances, non-destructive, in situ analysis of crystalline pigments on micro-areas of paintings and artefacts has become possible. This is illustrated with the application of this technique to the in situ analysis of propriety paints, paint cross-sections and small paintings. However, workers have noted that XRD can be insufficiently sensitive with pigment mixtures, due to matrix effects. This study obtained X-ray diffractograms of 17 single pigment preparations and determined relative amounts of crystalline content. The purity of single pigments was compared with Joint Committee on Powder Diffraction Standards (JCPDS) database diffractograms. The impact of pigments with high X-ray absorption coefficients on the detection limits of pigments with low X-ray absorption coefficients was further investigated by building on work done with the chromium oxide-zinc oxide series with the preparation of a second series of binary mixtures of zinc oxide (which has a high absorption coefficient and is almost fully crystalline) and ultramarine blue, which has a lower absorption coefficient but which is more crystalline. Semi-quantitative analysis, where baseline and absorption factor corrections are made, confirm detection limits as low as five per cent for chromium oxide and ultramarine blue when in a binary matrix with zinc oxide. However, this type of analysis is very time consuming. So in order to theoretically simulate issues that will be encountered with binary pigment mixtures, the single phase diffractograms were used to theoretically investigate the matrix effects of the three white pigments with the various coloured pigments. This illustrated that detection limits can be as low as five per cent or in non-ideal conditions, such as with partial peak clashes or where there are large differences in relative peak intensity, as high as 50 per cent. These results have significant implications for the analysis of painted surfaces on artworks or artefacts. It has been demonstrated that ideally this method is more suited to the investigation of surfaces where there is minimal mixing of pigments or where there is not a significant difference between the absorption coefficients of the mixed pigments.

Jan 1, 2008

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

Risk Management has been applied relatively slowly in the mining industry. Except for the risk concept application in financial considerations, the application of Risk Management in safety management has been far from satisfactory. When applied it was treated in a global occupational safety and health sense. Regardless of how much the mining industry has progressed over the years it is still, in many respects, `state-of-the-art' business. The safety aspects of mining are well known and yet little understood by the public. Regardless of what has been achieved so far and how much effort has been put into it, mining is regarded as an unsafe and somehow rude business. Safety records of the mining industry vary from State-to-State. Latest mining related disasters in PNG and Queensland and some other fatal accidents support this public perception. They purport a need for change in managing safety in the mining industry. The latest mining fatalities have raised the issue: What must be done to improve safety standards? Duty of care, risk management and system engineering concepts can provide some answers. Risk Management principles which have been advocated for some time provide many answers and explanations and can make safety management more constructive and workable. What has been missing so far is that this concept has neither been applied nor has been modified for its practical application and purpose on a larger scale. A risk management approach to the management of safety and health in the mining industry is addressed, herein. This approach does not attempt to provide the solution. It does, however, provide a basic understanding of what Risk and Risk Management are all about. Rational management of risk is addressed in the life cycle and system contexts. A system of continuous improvement is applied. There is always a chain of events, outcome, exposure, consequence(s), and consequence(s) value(s). It means that development of an event takes place in time and space. Dynamic circumstances have been created in or within the system. It is a decision-making process designed to provide a methodology which is directed not toward a mathematical model but toward easy use and application in dynamic working environment, by decision-makers who can be anybody from either a risk taker or a risk creator. The emphasis is placed not only on arriving at the best practical, possible and fair decision but also on structured and systematic acquisition of knowledge about the system, its hazards and associated risks, hence increasing the decision maker's ability to manage the decision-making process related to the management of risk.

Jan 1, 1995

For the last decade Australia has been the leading exporter of both steam and coking coal. In the ten-year period 1989 - 1998 steam coal exports increased by 93 per cent and metallurgical coal exports increased by 50 per cent. However, profitability of the steam coal sector has been disappointing. The coking coal sector, especially the hard coking coal segment, has fared better but its profitability was more because of its ability to maintain relatively high prices rather than its inherent productivity. Until quite recently the Australian coking coal sector was widely expected to be able to maintain this comfortable state without undue effort for the three major æpartnersÆ; the companies, the State Government and the unions. But coking coal could now be heading down the path followed by steam coal that ends with long-term over-supply and, despite steady improvements in productivity, poor profitability. Steam coal entered the ænewÆ era of long-term over-supply some years ago. Over-supply was due to the rapid increase in production in Indonesia, often from new mines and Australia. AustraliaÆs production rise was underlain by the apparent belief that the best way to lower costs was to increase production. In the first couple of years costs didnÆt fall much but the additional tonnage was sold at lower and lower prices into the spot market. By mid-1998 the difference between the contract price set with Japanese utilities and spot sales was often in excess of $US12 per tonne. Japanese contract prices and tonnages have since fallen significantly. Steam coal has moved from being a product to being a commodity. Any profits are due more to the low Australian dollar rather than inherent mine productivity. Seaborne coking coal trade has been dominated by Australia, Canada and the USA, with the USA becoming less competitive. Unfortunately, when the Queensland capacity expansion was well down the pipeline, the Asian financial crisis occurred and the Japanese economy entered what appears to be a long-term recession. Contract prices fell 18 per cent, tonnages decreased and some mines have been reclassified as supplying lower priced coking coal. The paper analyses past and expected future trends in labour and mine productivity, rail freight and FOB export port cash and total costs of the Australian steam coal and coking coal sectors and discusses the market outlook for Australia. The future economic viability of the industry is analysed and discussed in the light of the rapidly changing global environment.

Jan 1, 2000

By C Kocsis, G Baiden, Y Bissiri

CANMET-MMSL and Penguin Automation Systems Inc have been exploring how process simulation and ventilation modelling software, when combined, can be used to optimise hard-rock/metal mine ventilation systems. In combination, it is anticipated that this methodology will facilitate the exploration of mine design options that affect ventilation requirements and ultimately cost. Such integrated mine design could limit, and possibly reverse, the drivers that under current practices would generally dictate increased ventilation, power consumption, cost and greenhouse gas emissions. It is believed that the mining industry needs such process models to develop better business cases. For example, the implementation of optimised ventilation systems will undoubtedly require significant investment and mines are often reluctant to try such conservational measures unless they can be proven cost-effective. In general, Canadian hard-rock mines know their ventilation systems are providing too much air and consuming power unnecessarily. This is because their systems are designed to provide maximum production flexibility, based upon peak demand, which may be at some future time, and operated continuously at that level regardless of actual need. Simplistic analyses have shown electrical energy savings can range from 30 per cent through to 90 per cent (Hardcastle, Gangal and Leung, 1998). These savings depend upon such factors as the intensity and continuity of the production schedule as opposed to non-productive time. Where these savings occur is also important, if limited to either the primary or auxiliary ventilation systems, they could be negligible in a mineÆs total energy consumption. The problem these mines face is determining what level of ventilation is required in real-time and then the relative benefits. Such parameters as varying electricity costs, heating fuel options, different design criteria and their complex inter-relationship can effect the selection of an optimal system, depending on whether energy, environment or cost is the prime driver. The use of process simulators in underground mining is in its infancy; to date they have been used to show the benefits over the life of a mine under different mining methods, such as a comparison of tele-remote mining from surface against conventional manned operation (Baiden, 2000). This ongoing development advances the use of such simulators into a new and potentially important area, namely modelling the life-cycle ventilation requirements of a mine. This paper shows how such a life-cycle analysis as opposed to peak demand can provide the basis for optimising the design of ventilation systems and their control.

Jan 1, 2005

By P Hawkes

Within the mining industry computers have made their most significant impact with 3D design, visualisation and resource modelling/ optimisation. Recently, the application of computers to data gathering and accounting functions has also started to reap benefits. These two areas of application cover the beginning and end of the mining process. There has been limited use of computers on the middle section, the actual mining process. This is interesting when considering the relative proportion of overall mining costs that this section produces. There is a certain amount of irony in the lack of mining application software for developing accurate budgets compared to the systems/software then used to review performance against budget. Computers have been used extensively in the manufacturing industry to design, model and simulate the manufacturing process. This has not been extended to the mining process. But, we all strive to have an open pit that replicates a manufacturing plant û smooth, efficient, optimal production. If we could model mining operations with the confidence of plastic box makers we would reduce risk by an order of magnitude, improve planning and focus on value drivers. Cost û benefit analysis would be easy. The extrapolation of manufacturing to mining process models is difficult. The variables in the manufacturing process are fewer in number, have low volatility and are highly predictable. The time between a box falling on a conveyor belt and falling off is very consistent. Mining is quite the opposite. It has large numbers of variables, some of which are unpredictable and volatile. The time to fill an excavator bucket could vary by 30 per cent and the frequency distribution is unlikely to be a mathematically simple normal distribution. Further, each of these variables can be distorted by one-another û they are interrelated. The mining process is a disjointed flow of parcels whereas manufacturing is a controlled continuous feed. A loaded truck might join a ramp and follow a slow water cart up. This is the equivalent of a localised voltage drop on equipment in a manufacturing plant. The manufacturing plant is quite likely to rapidly recover to full capacity. Whereas the slow truck might throw the mining fleet cycle out of balance for hours û trucks queuing at the ROM bin and so on. A mining process simulation has been created that addresses these mining variable issues to produce a highly accurate model of the open pit mining process. The number of uses for such a model is growing rapidly as it is being utilised for a variety of projects within the industry. This paper discusses the need for and application of mining process models.

Jan 1, 2003

The decrepitation technique is a rapid means of measuring abundances, temperatures and to some extent the fluid compositions, of fluid inclusions in transparent and opaque minerals. The method has been used to investigate the hydrothermal fluid systems associated with gold mineralisation in the Tennant Creek, Pine Creek and Halls Creek Goldfields. At the Enterprise Mine, Pine Creek, several different stages of quartz veining are distinguished and within these, gradational changes in fluid temperatures and compositions help to define the centre and nature of the thermal system responsible for the mineralisation. In the surrounding Pine Creek region and at Tennant Creek and Halls Creek, the results were applied on a regional scale to characterize outcrops and aid in the discrimination between potentially mineral- ized and barren outcrops. The decrepitation method involves the heating of a small (lgm) sample of crushed and sized grains up to as high as 800 degrees celsius. During the heating the fluid inclu- sions within the grains develop sufficient internal pressure to physically burst, the temperature of such bursting being dependent on the type of fluid and the prevailing tem- perature at the time the inclusion was originally trapped. The resulting tabulation of the number of inclusion bursts per 10 degree temperature interval is plotted as a histogram of decrepitations versus tempera- ture and called a decrepigram. The decrepi- grams frequently show several distinct peaks at different temperatures which are caused by different populations of inclusions in the sample. The areas of the peaks indicate the abundances of inclusions in each population while the shape and mean temperature of the peak provides a guide to the type of fluids involved. Of particular importance in this study is the presence of decrepitation peaks at fairly low temperatures (around 2000 C. These are characteristic of C02 rich fluids which build up internal pressure very quickly when heated. The Enterprise Gold Mine at Pine Creek comprises a number of overlapping quartz vein systems hosted by Burrell Creek Formation sediments. The geology of this mine has been described at this conference by Dann and Delaney, who have defined several distinct stages of quartz veining based on structural, mineralogical and physical features of the veins. For this decrepitation study, 19 quartz samples from the mine and environs, including some from each stage of veining were collected. These results suggest that there are 4 major vein types, within 3 of which additional small variations can be discerned which are due to gradational changes in the temperatures and fluid compositions in the mine area.

Jan 1, 1984

Life inside the mining family was regulated by the mine. The whistle shrieked the change of shift to the Cornish, Welsh and German miners digging the alien soil for copper at Burra in the 1840s and the deep quartz gold mines at Bendigo in the 1880s.During the golden years of alluvial mining in the 1850s, and later out on the frontier fields of Kalgoorlie and Jarrahdale in Western Australia, the lure of the mine dominated family life. How could it do anything else? The canvas tent, bark hut or weatherboard cottage in which the mining family lived close by the mine facilitated prompt access. The working man of the family attended to the demands of the mine first, and those of his family afterward. Who then organized and nurtured the mining family? The role of the mining wife was multi-fold. She played the traditional roles of home-maker and comforter, raising her children, tending her house and vegetable garden and supporting those friends and acquaintances who had lost children to disease, or menfolk to the mine. Epidemics of measles, the whooping cough or influenza carried away children in infancy or at too young an age. The death of a husband through accident or disease (pthisis was a likely killer) forced upon the mining wife another role, that of provider. When Elizabeth Vigus' husband died in a Bendigo mine accident in March 1880 Elizabeth set up a grocery business to support her young children.' But in other cases the mining wife supplemented the family earnings by part time work, not in the mines for the Mines Act legislation of 1842 forbade the working of women underground, but in auxilfiary occupations which were in demand.2 Ann Mitchell, a herbalist ,found plenty of work in the goldfield towns of Daylesford and Maldon in the 1860s and 1870s.3 So too did Susan Rule and her daughter Catherine who conducted a sewing and millinery establishment in Beechworth in the 1870s.4 The making of the family's clothes was another task of the mining wife and mother.Until the wonderful invention of the sewing machine, this was a tedious and time-consuming task. James Slater Edmonson bought his wife a Wertheim for the sum of 12 pounds in June 1886, just before leaving her and his chil- dren in the Adelaide suburb of Goodwood whilst he went alone to the goldfields of the West. In October of that year he wrote to Louise telling her how he missed the childrens' wondering "whether Slater wore my old shirt now. I always think of him as he sat on my knee at breakfast in that old shirt; and how pleasant it would be if I could rock both of them and sing as I used to do".5

Jan 1, 1988

HISTORY OF PROCESS DEVELOPMENT The manufacture of coke from coal commenced at the beginning of the 17th century by heaping coal into circular mounds in the open, covering with earth, clay or ash and slowly burning the coal in the mounds to produce a heap of coke. Naturally the process was slow in production rate with low coke recovery due to the loss of that part of the coal which was completely burnt to ash. As a natural consequence of this initial carbonisation method, a coke oven design was developed so that the coking chamber, which was constructed of brick, was circular in plan, cylindrical in section with a dome shaped roof - similar in shape to the original coal mounds. As the shape of the chamber was similar to the old dome shaped beehive, the ovens were called beehive ovens. The ovens were built in long single or double rows with retaining walls between each oven and as such were known as a battery of beehive coke ovens. In these early beehive ovens, coal was charged from hand wheeled tubs into a hole into the top of each oven, hand- levelled with a rake and the oven side opening sealed with bricks and clay except for some small holes in the opening to admit limited quantity of air for combustion. Coking commenced by the heat retained in the brickwork from the previous charge. The gases evolved from the coal, together with the admitted air, were partially burnt inside the oven to supply the heat for carbonisation and the surplus gases were burnt to waste at the top charging hole. The heat from this gaseous combustion inside the oven together with the reflected heat from the brickwork of the arched roof of the oven allowed carbonisation of the coal charge to proceed from its surface slowly downwards to the floor of the oven. At the end of the coking cycle (usually 4 or 5 days) when there was no more evolution of gases, as indicated by diminishing gas flame and a drop in oven temperature, the brickwork of the oven opening was removed. The coke was then quenched by inserting a pipe with spray holes to spray water over the coke charge in the oven after which the coke was raked from the oven. The work of charging and levelling the coal, bricking and removal of oven opening, quenching and raking out the coke all required manual labour. As these ovens only carbonised a 5 to 7 ton charge of coal per cycle of 4 to 5 days, to produce 3 to 41/2 ton of marketable coke, the labour required per ton of coke was high.

Jan 1, 1975

The use of scrapers in mining and earthmoving operations is not new; in fact they are one of the earliest methods of bulk earthmoving. A single machine, which can load, haul, and dump material with a minimum of ancillary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. Maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancillary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By Ross J. F

A pillar 'is a block of coal left in the first working of a coal seam for the purpose of supporting the superincumbent strata in such a manner that the winning out roadways will be safe to traverse by men and by the coal transport system.PRINCIPLES OF PILLAR EXTRACTION.The size of a pillar is chiefly dependent on the depth of cover, and in a lesser degree on the nature of the coal, or the condition in which the seam has been laid down. In a seam at 1,100ft. depth of cover, and assuming a spec'ific gravity of 2.5 overall for the cover strata, a pressure of 1,200lb. per sq. in. is the loading on the top surface of the coal seam before mining begins.When mining commences, and as the pillars are formed, an increased load is imposed on the coal left in the pillars, according to the percentage of coal extracted in the first working. Thus, if 25% extraction is taken in the first working, the load on the pillars is theoretically increased from 1,200lb. per sq. in. to 1,600lb. per sq. in. over the area mined. If this state of things went on indefinitely it would not be possible wholly to extract a pillar because of the extreme pressure tliat would be thrown on the diminishing portion; but, fortunately, another element, that of time, enters into and assists the process of extraction.If the superimposed strata were of an entirely plastic nature, this time factor could not operate, as the cover weight would settle instantly on the remaining portion of the p'illar and finally overwhelm it. The cover strata above a pillar generally have a certain rigidity which does not allow the superimposed weight to settle instantly on the pillar fraction, and it requires a period of time to elapse before the extra weight is felt by the pillar.The time factor varies widely, and is governed entirely by local conditions; it can only be determined by experience gained on the spot or in close proximity to the area of operations. It is dependent on the strength of the strata and its characteristics under bridging conditions.It is, therefore, logical to assume that the more rapidly a pillar can be extracted the greater will be the safety factor and also the percentage of recovery of coal.Up to the present time, the operation of the extraction of pillars in this country has been, with a few exceptions, a manual one, and before mechanization of Collieries can be fully accomplished, the process will have to be performed mecharrically.

Jan 1, 1947

It is recognised by the current JORC (1999) code that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological continuity and grade continuity. No prescribed criteria and rules will work for all situations or even between different ore types within the same deposit. Also these criteria and rules are sometimes applied without a clear understanding of their appropriateness, accuracy or correct implementation. For these reasons case studies are useful to evaluate and compare criteria commonly used to assist in resource classification. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody are used as the basis of a case study for the above-mentioned purposes. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce a random sample grid, a semi-random sample grid and a regular sample grid. Using nearest neighbour, inverse distance squared, ordinary kriging and sequential gaussian simulation, block iron grades are estimated using these three blasthole data subsets as inputs. This provides four groups of estimates with the ordinary kriging estimate based on the complete blasthole dataset being considered to represent the true estimate of iron grades. Also generated during this process are estimates of the error for each block. These error estimates range from the simple, such as drill spacing, through to more advanced methodologies such as kriging efficiency and simulation. These estimates of grade and grade estimation error are then compared to the true estimate using graphs and statistics. In order of increasing accuracy the block grade estimation and simulation methods were nearest neighbour, inverse distance weighting, ordinary kriging and finally conditional simulation. The simulation in some instances doubled the accuracy of individual block grade estimates when compared to nearest neighbour and inverse distance weighting estimates. It was found that many methodologies for estimating the error of individual blocks performed equally well with only methods such as average drill hole spacing and classification by search ellipse pass number performing poorly. An approach on how to convert the abovementioned error estimates of individual blocks into a meaningful JORC classification is also discussed. Although advanced non-linear resource estimates are applicable, most iron ore mines are still using relatively straightforward methods. The use of blasthole data and some simple linear interpolation methods and simple linear based error estimates makes this study repeatable for most iron ore sites and their resource geologists. This style of investigation is recommended as a useful approach for the Competent Person to apply to their deposit and thus better select, implement and understand the criteria used for resource classification and provide more consistency and confidence in the resource classification process.

Jan 1, 2002

By D H. Bell

Slab-buckle failures in coal sequences involve thin slab deformation in strata dipping parallel to the footwall, and are a consequence of both unloading and the weak nature of the thinly bedded rock mass. Methods of modelling and predicting such occurrences include: +        a conceptual model using a base friction table, +        a mathematical model using the Euler solution for column and beam bending (after Goodman, 1980), and +        computer analysis techniques such as UDEC (Universal Distinct Element Code after Cundall and Hart, 1993).   Slab-buckle failures have the potential to seriously disrupt production because of their volume and rapidity, and to endanger both equipment and personnel working on the pit floor.   In July 2004 a large slab-buckle failure occurred overnight after a new batter and bench had been formed at the Malvern Hills Opencast Mine in inland Canterbury. This involved the entire length of the pit (85m along strike) when a 2m thick intact slab with a total volume of ~3500m3 translated down dip 6.2m on the base of a thin coal seam to form a pronounced buckle at the toe. The coal measures consist of finely laminated mudrocks with multiple coal seams of varying thickness dipping ~45¦ to the southeast, and the opencast mine had been designed with footwall batters formed parallel to bedding with a vertical bench separation of 15m.   Back analysis of the Malvern Hills failure was necessary to investigate the controls on footwall instability, and for future mine design. An engineering geological model was created and samples of the slab material and failure surface were collected and tested to establish the required parameters for use in the Euler solution for column and beam bending. Back analysis using the Euler solution provided unrealistic results that overestimated the overall length of a stable slope by more than 10 times.   No further large scale slab-buckle failures have developed at the mine site, in part because of the slow rate of coal extraction, but precautionary drainage of the footwall slopes has been undertaken to improve overall batter stability. The location of the slab-buckle failure on a critically positioned pre-sheared thin coal seam with full hydrostatic head is considered the most probable cause of the July 2004 failure, rather than inherent instability of the generic bench and batter arrangement adopted. The use of a precedent-based engineering geology approach to future mine design is considered the most appropriate solution in the circumstances.

Jan 1, 2007

By Georgi H, Farquhar J. W, Lorrigan A. N

The potential for major new lenses of Volcanic Hosted Massive Sulphide (VHMS) beneath the existing Rosebery Deposit is extremely high. Recent deep drill hole intersections of massive sulphides, including 22 in true thickness at 24 per cent Zn, may significantly extend the life of the Rosebery Mine. The Rosebery Ore Deposit is located within Australia's most prospective VHMS mining district, the Mount Read Volcanic (MRV) arc of western Tasmania (Figure 1). The MRVs are a 10 - 15 krn wide arcuate belt of lavas, related intrusives and volcaniclastics. Rosebery is a major Cambrian volcanic hosted Zn-Pb-Cu-Ag-Au rich deposit which has been over-printed by Devonian deformation and granitoid alteration resulting in local rcmobilisation of the ore. The Rosebery Mine Sequence is composed of an east dipping and east facing, predominately felsic sequence of rhyo-dacitic volcaniclastics, epiclastics, sediments and shale lenses more than 500 in thick. This sequence is bounded by two, low angle (35 - 40¦), east dipping thrust faults, the Rosebery Fault to the west and the Mount Black Fault to the cast. The Rosebery Mine lithologies are summarised in the following table: Hangingwall (HW) Polymictic, quartz, feldspar-phyric epiclastics. Black Slates Graphitic, pyritic mudstones. Host Rocks Turbiditic mudstones and sandstones. Footwall (FW) Feldspar-phyric, pumiceous, mass-flow breccias. Cambrian, quartz-feldspar, porphyritic sills intrude this sequence at all levels. Thin, Jurassic, dolerite dykes also occur throughout the mine. Widespread quartz, sericite and chlorite alteration occurs in the FW. This alteration is manifested as quartz-augen schists beneath the orebody. The Host Rocks are pervasively altered with silica, sericite, chlorite and pyrite. Intense carbonate alteration occurs within the orebody, whereas chlorite and pyrite alteration is commonly concentrated directly beneath it. Cambrian volcanogenic alteration is over-printed by three major Devonian, granite-derived, assemblages. These are massive to quartz veined tourmaline, pyrrhotite-pyrite and magnetite-chalcopyrite. Though the Devonian granite has not been intersected in deep drill holes or in mine workings, there is good evidence that it exists within a kilometre of the deposit. The Rosebery orebody is structurally complex when compared to many other VHMS deposits. Evidence for Cambrian growth faulting has been found at the North End of the mine (B lens) where displacement of ore lenses occurs without corresponding displacement of the overlying Black Slates. A well defined cleavage exists throughout the mine, dipping at 28 to 50¦E. East dipping shear zones are also obvious in all parts of the mine workings and reverse movement is evident on many of these.

Jan 1, 1993