Search Documents

By Martin R. E

L44 Shaft is a major upcast ventilation shalt in the hanging wall of the 1100 Orebody. Various techniques for stripping a raisebored pilot hole were combined to produce L44 shaft. From the surface to 198 m depth, the shaft was concrete lined 7.3 m internal diameter. Below this the shaft was developed to 7.6 m diameter unlined. 11 level, 540 m below the surface, was the first readily accessible level connection. The section to 198 m depth was benched and concrete lined through weak oxidised ground. When more competent ground was encountered the operation was converted to horadiam stripping. This application of the raiseborer has led to a safer, more efficient method of shaft development.

Jan 1, 1977

Samples weighing 0·5 g are fused with sodium hydrogen sulphate, leached with 5 ml. of 4 M nitric acid and diluted to 10 ml. with water. An aliquot of the clear solution is boiled with concentrated nitric acid and then 2 ml. of a phosphotungstate solution are added. After dilution to 10 ml. with water, the solution is heated in a boiling water-bath for not less than 10 min. When cold, the solution is extracted with 2 ml. of iso-amyl alcohol and the yellow phosphotungstovanadate complex is compared with a standard series. Concentrations down to 4 p.p.m. may be analysed at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

By E Hogan, M Goodz, R Wright

The planning, permitting and monitoring procedures of the re-opening and rehabilitation of mine sites is an ongoing process which must continue throughout and beyond the life of the project. Both industry and government bodies must remain flexible to allow guidelines to be altered where and when necessary.To enable the successful re-opening of the Morning Star mine at Woods Point in alpine Victoria, many environmental and historical issues had to be evaluated.The site which had been derelict for 28 years had to be rehabilitated to a safe and aesthetically pleasing state prior to construction of a new operating mine site. Considerable liaison with government authorities and the local community was required.

Jan 1, 1992

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

On Wednesday 11th November, 1970, a series of violent explosions occur-- red within No.1 Basic Oxygen Steelmak- ing (B.O.S.) furnace at the Whyalla Works of the Broken Hill Proprietary Co. Ltd., (B.H.P.) when the furnace was moved immediately prior to tapping. Water from a burnt out flux chute had flooded the bath while the furnace was tilted slightly towards the tapping side waiting to tap. Although no one was injured, dam- age in excess of $54 000 was caused to the hood and superstructure. The water hydrated the burnt dolomite refractory lining some of which sub- sequently collapsed exposing bare fur- nace shell over part of the cone.

Jan 1, 1975

By Minglin W, Zhixing L

The laws of detonation wave velocity variation in propagation process along the charge under channel influence are investigated widely in this paper. The result is obtained by blasting experiments. Bore hole is simulated by plastic tube or steel pipe (with outer diameter 45 nun, inner diameter 40 or 41 mm). Blasting experiment is carried out with a cylindrical charge of 32 mm diameter. The author analyses the characteristics of energy distribution along the charge under above-mentioned conditions. Reasonable initiating position and initiating direction are also analysed. A double-direction initiating method which consists of several initiating charges is put forward. The blasting effect of this initiating method when used in underground mining is stated out.

Jan 1, 1990

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities.

Jan 1, 2002

Mr. Bradford said: - On assuming this chair, which has been oc- cupied by so many gentlemen of conspicuous ability, my first words must be an expression of the gratitude I feel for the honour you have done me in electing me to be your President for this year. When considering the subject matter of this address to you to- night, quite frankly may it be stated that for a long time I was on the horns of a very great dilemma, for while I could discourse on the modern political trend in relation to our industries at great length, it appeared to me that this was not the place for such a discussion.

Jan 1, 1987

Structural assemblages of veins, shear zones, and wallrock alteration zones arising from fault-valve action on steep reverse fault systems are reviewed using observations from mesothermal gold-quartz lodes in the Archean Yellowknife, Abitibi, and Yilgarn greenstone belts of Canada and Western Australia, the Cretaceous Mother Lode system in the Foothills Metamorphic Belt of the western Sierra Nevada, California and the Victorian goldfield hosted in a folded quartz-turbidite succession of Paleozoic age in Australia. Despite differences in the host rock assemblages, the deposits have many structural characteristics in common. These form a useful exploration guide when re-evaluating comparable, but poorly described gold-quartz vein systems such as those in the Reefton area of New Zealand.

Jan 1, 1992

Consideration was given to the.applicab on of a solvent extraction circuit to be'included in the process'for the-recovery of a high grade product from.:-the Rum Jungle Creek.South uranium ore body.The economics of two alternative processes, firstly the Eluex process which uses an ion exchange process followed by solvent extraction.-of a.high grade sulphuric acid eluate, and secondly a process using direct solvent' extractioh of pregnant leach liquor, were studied. There was a small cost advantage favouring the Eluex process but when other factors were considered, the installation of a direct solvent extraction process appeared the better long term investment. A solvent extraction plant was installed at Rum Jungle in 1962.

Jan 1, 1963

Recent data contributions to New Zealand Mesozoic terrane geology confirm the consensus interpretation that New Zealand grew by the progressive addition of material by plutonic and accretionary processes along the Gondwana margin. The data also (1) emphasise the discontinuous but inter-related nature of these processes of continental growth, (2) better establish a direct Gondwana correlation of the Western Province and probable Gondwana provenance of at least some of the Eastern Province, (3) suggest specific times and places when passive or strike-slip rather than subduction regimes are recorded along the south Gondwana margin, and (4) potentially lead to interpretations emphasising parautochthonous rather than far- travelled relationships between many New Zealand terranes.

Jan 1, 1995

By Giannini LM, Carras S

A fundamental problem in mine planning is that of determining the "optimum pit limit" of a mine. This optimum pit limit yields information which is considered essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long -, intermediate -, and short-range mine plans. Since the mid 1960's a number of mathematical techniques based on the "block model" have been proposed for solving this problem. When applied to large ore-bodies the implementation of these techniques, especially the more elaborate ones, poses considerable computational problems. In this paper we report on our work, done jointly with Systems Research Institute of Australia (SRIA), in devising strategies for overcoming these Problems.

Jan 1, 1986

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, 'The cheapest crushing is done in the pit', appears accurate in this case study. Comparison of the accumulated cost of powder, selected wear materials and electricity, indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone. Measurable, overall costs decline while shovel and crusher productivity rise by about five per cent when powder factor rises by 15 per cent. These trends were previously masked by the effects of weather, ore grade fluctuations and accounting practices.

Jan 1, 1995

Many parameters are important when considering the performance of a concentrator. These include metallurgical performance, such as throughput, metal recovery and final concentrate grade and operating costs, such as power consumption, water usage, reagents and spare parts. In most operations the objective is to maximise metallurgical performance and minimise operating costs, ideally without a large investment in new capital items. A number of projects have been carried out at Newcrest MiningÆs Cadia Valley Operations (CVO) with the aim of improving metallurgical performance and minimising operating costs. This paper focuses on the installation of newly designed flotation mechanisms in various cells in the Cadia flotation circuit and describes the effect these changes had on performance and operating costs.

Jan 1, 2009

By Spottiswood DJ, Kelly EG, Bull WR

An empirical model of a 254mm water-only cyclone treating minus 17001im coal has been developed. The model includes the prediction of by-passing, SG50 corrected, water split and the use of a single equation forthe reduced performance curve of particles in the range 1700-106pm. Particles finer than 106pm did not separate according to specific gravity. Simulations using the model showed the water-only cyclone performance to be dependent more upon feed size distribution than washability when the feed contains high-ash fines, but that, with a deslimed feed, the yield and ash content of the over-flow should be controllable by altering feed rate or feed pulp density.

Jan 1, 1985

By Johns A. L

The concept of the Melbourne Underground Rail Loop and the organ- isation to achieve its construction are covered in the companion papers (Reference 1, 2) and will not be repeated here. The Victorian Railways, as well as being the eventual operator of the Loop when it is completed by MURLA, have also been responsible as "Contractors" to MURLA for the construction of the "cut and cover" or "box" tunnels and related approach works located on existing Railway property. These tunnel connections link the existing suburban system to the new underground works. The following tabulation indicates the significant work volume involved in this cut and cover tunnelling exercise and which is covered in some detail by this paper.

Jan 1, 1981

By Mutmansky J. M, Hartman H. L

Multiple operating points for mine fans are a problem that fan and mining engineers must constantly be aware of in mine/fan systems. In a single-fan system, unstable conditions can be avoided by restricting fan operation to the "normal operating range." When mine fans are operated in parallel, the situation becomes a little more complicated. Multiple operating points are more often encountered and the fan user must be aware of these multiple points to have a suitable set of operating conditions. However, for fans in parallel, the engineer can plot the combined characteristic in a relatively straightforward manner and thus can avoid conditions that would cause instability in the mine/fan system.

Jan 1, 1988

Autogenous and Semi-Autogenous grinding has become an accepted method of reducing primary crusher product to micron sizes in a single or a two-stage grinding circuit. The elimination of secondary and tertiary crusher circuits and sometimes rod mills helps to lower overall operating costs and, in many instances, can make uneconomical projects viable. Selecting AG/SAG Mills have been rather a "hit and miss" affair over the years, but now with the many different types of tests available, accurate mill size predictions can be made, provided the test data is evaluated correctly. This paper endeavours to simplify the process of evaluating test data and sets down some guidelines for designers to follow when selecting AG/SAG Mills.

Jan 1, 1991

By M E. Pierce

Recent advances in comminution and heap leach technology have resulted in the development of many large-scale, low-grade open pit mines that coincide with areas of historical underground workings. Twoand three-dimensional numerical modelling has been conducted to assess the interaction between open pit slope stability and remnant underground voids. Most design analyses for open pit slopes assume a two-dimensional problem geometry. This is not the condition encountered in practice ù particularly when remnant underground voids interact with a large-scale open pit slope. Three-dimensional numerical models have been shown to provide a more realistic representation of the interaction between overall open pit slope stability and remnant underground voids.

Jan 1, 2003

The Olympic Dam Mining Operation involves the supply of some 2.2 million tonnes per annum of ore feed for the metallurgical plant. To achieve this approximately 9 km of tunnels are developed per year to gain access to the long hole open stopes that supply the majority of the production tonnes.Vast amounts of data are produced in the mining activity from the geology, mine design, scheduling, surveying, shift reporting through to the statistical reporting and analysis of the performance of the mine activities. Care must be taken when obtaining the data to maximise the usefulness of the data to other users so not to impose constraints or additional processes on future users.

Jan 1, 1992