Search Documents

By Bahsford A

The presence of coal in the Sydney area was confirmed in 1891 when Cremorne Bore No. I intersected cindered coal at 1 854 m. The decision to develop Sydney Harbour Colliery was based on the results of Cremorne Bore No. 2 (drilled in 1892) in which a 3.12 m. seam of unaltered coal was encountered at 889 m. Geologists from the New South Wales Department of Mineral Resources consider that this seam is probably equivalent to an upper split of the Bulli seam. Long Cove at Balmain was selected by Sydney Harbour Collieries Ltd. as the site for mine development in 1896. This was due to opposition to the proposed establishment of a colliery on the north shore of Port Jackson near Cremorne. Construction of the main access and ventilation shafts (termed Birth- day and Jubilee), other mine infrastructure and the quay wall occurred between 1897 and 1902. A fatal accident in which five men were killed occurred during the construction of the Birthday Shaft in 1900. This acci- dent resulted in amendments to the Mining Act providing for guide rails in shafts.

Jan 1, 1988

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

Hamersley Iron Pty. Limited has maintained an interest in the screening of iron ore fines (nominally -6 mm). However, no dry screening process had successfully demonstrated acceptable separating efficiencies at high tonnage rates, low operating costs, and mechanical reliability when screening iron ore fines (containing up to 6% free moisture) at sizes of around 1 to 2 mm. A new type of vibrating inclined screen has recently been developed which is claimed to have a non-blinding screening surface. It was decided to test a pilot scale unit in an existing pilot plant located at Hamersley's facilities at Dampier, Western Australia. The appropriate operating parameters such as vibration speed and feed rate were determined using one fine ore type. Mats with different aperture sizes, and different feed moisture contents were also tested. Trials were then conducted on various fine ore types to indicate the effect of different size distributions on separating efficiencies. The effects of feed moisture content were determined with these ore types, and a blend of lump (nominally -30+6 mm) and fines was tested to compare the screen's performance with that of the bottom deck of the minesite product Screens.

Jan 1, 1991

Like almost any other 19th century mining area, the West Coast saw its 20th century scrapping era when machinery which had been installed in seemingly inaccessible places was somehow dragged out again. Fortunately there were some spots so remote that they defied even the most zealous of these pioneering recyclers. One of these was Big River, a mining locality in a rugged landscape straddling the headwaters of the Grey and Inangahua rivers. As a result there remains an internationally important collection of mining equipment including a poppet head, two steam winding engines, a pair of boilers, part of an aerial cableway with its loading system, and remnants of a stamp battery along with its associated gold smelter, cyanide tanks and zinc boxes. There are also assorted building remains associated with 60 years of mining and settlement. Since their abandonment in 1942, these relics have all somehow survived a further half century in a far from favourable climate with two or three metres of rain a year, frequent snowfalls and hot summer temperatures. The rate of decay during the past few years has been alarming.

Jan 1, 1996

By Barber C, Buselli G

Detailed monitoring of point sources of groundwater pollution is expensive due to the high cost of drilling monitoring boreholes. Whether groundwater pollution is due to mining, industrial or domestic waste disposal, a universal difficulty when monitoring groundwater contamination is the placement of boreholes to adequately define the extent of the pollution plume. This paper reports groundwater 'resistivity variations determined from transient electromagnetic soundings at a domestic waste disposal site north of Perth in Western Australia. Together with available hydrogeological and water quality data, the geophysics provides a broad "plume scale" picture of groundwater contamination. A simple three dimensional model of plume development, which takes account of the dimensions of the wastes, has also been developed and shows good agreement with the spread of contamination indicated by the geophysics for relatively small values of the dispersivities. Better estimates of these parameters are still required. The work indicates that a combination of geophysics and modelling with ground-truth data from groundwater quality monitoring of boreholes is required to avoid difficulties in interpretation of data and to better define the extent and migration of pollution in Groundwater.

Jan 1, 1988

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By E V. Man, O N. Savassi, J-P Franzidis

In flotation, the property that is exploited to effect the separation of a mineral from an ore is referred to as its floatability. Assessment and quantification of ore floatability is of fundamental importance in modelling and simulation of flotation circuits. This paper describes the design, construction and operation of a new laboratory flotation rig that has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to determine the floatability of different ores on a small-sale. The rig is designed for continuous operation. The major features of the rig are highlighted in this paper. An unique characteristic of the rig is a 9.1 L conditioning vessel. This provides a mixing regime close to plug-flow which avoids complications such as different collector coverages for similarly sized particles (which would considerably increase the complexity of ore floatability determination). The main advantages of this rig when compared to conventional batch flotation cells include better control of the chemical environment and the ability to determine froth recovery, entrainment and water recovery with increased accuracy. Preliminary tests undertaken with a high-grade lead/zinc ore from BHP Cannington are presented demonstrating the good level of reproducibility obtainable in operating the equipment.

Jan 1, 2000

By Gole MJ

The Goodyear nickel prospect is located 45 km southeast of Kalgoorlie (31.04¦S, 121.80¦E) near the eastern boundary of Hampton Area - East Location 45 (Figure 1). Nickel mineralisation was discovered on the Goodyear prospect in March 1996 when a reverse circulation drillhole (GYC5), initially drilled in December 1995, was deepened to meet a minimum footwall penetration requirement of 20 in that had been set for the drill program. Approximately 3 in of sulphides averaging 4.9 per cent nickel was intersected from 296 metres down-hole, this being within 2 in of the first end-of-hole. Hole GYC5 was part of an eight hole drilling program undertaken by Titan Resources in late-1995. This program was designed to test whether nickel mineralisation in the Dunlop prospect, discovered by the Western Mining Corporation - BHP Camylia Joint Venture immediately east of the East Location 45 boundary, continued across the tenement boundary. The area targeted by the initial drill program had been explored by Western Mining Corporation in the mid-1980s using extensive surface sampling and a drilling program that included 17 RAB and percussion drillholes. None of these holes intersected nickel Mineralisation.\

Jan 1, 1996

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

The introduction of rubber tyred diesel equipment underground in the early 1960's and subsequent design improvements to diesel haulage systems over the past 2 decades has meant that diesel truck haulage has often been the first choice when selecting a haulage system for a new underground mine. Even today only 9% of all vehicles underground are electric powered.However, with the development of more efficient electric haulage systems, the suc-cessful installation of low cost shaft hoisting systems and improvements in conveyor design, alternative haulage systems are appearing as viable alternatives to diesel truck hauling. In particular, the aspects of ergonomic and environmental operating conditions, maintenance and operating costs as well as productivity rates are becoming more and more important in the selection of underground haulage systems. Future develop-ment of existing diesel haulage systems will require that diesel haulage units become more productive, have considerably reduced exhaust emissions compared to existing units and remain the cheapest haulage method for under-ground one way haul distances up to a distance of 3 kilometres. Development of electric truck and associated fuel cell haulage systems

Jan 1, 1985

By Wardle L, Wright G

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modem houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various' house designs.

Jan 1, 1992

ABSTRACT- I Chemotrophic bacteria, capable of oxidising inorganic species such as Fe(II) and S(-]I) for their metabolic energy, have been known for many decades and interest in these bacterial species has increased since their ability oxidise auriferous arsenopyrite ores has been demonstrated. The rate at which bacterial cultures can oxidise a solid sulphide ore is of importance but a number of difficulties arise when attempting to evaluate this oxidative activity. The two major problems are counting the number of viable bacteria present in the reactor and identifying the types of bacteria that are active in both the solid and liquid phases. Enumerating the numbers of bacteria responsible for an observed change is necessary to compare the activity of different isolates. For selection and identification of bacteria during the development stages of a project, and for monitoring an operational process, the recognition of different species will be of importance. Methods for the taxonomic discrimination of bacterial species rely on observations, different culturing techniques, and the degree of DNA base homology between isolates. A method reported recently uses IR spectroscopy for comparisons between isolates. This spectroscopic method and its application is discussed.

Jan 1, 1991

By C Gypton

This paper gives some insights into what to look for when reviewing feasibility studies. The review by a third party is an important element of the risk management process and may be the last remaining opportunity to uncover errors, or identify and reduce project risks on paper before they are converted to financial disappointments, steel and concrete monuments to process failures or cost overruns. The mining industry has had a spotty record in the area of estimating initial capital costs and operational performance, even though the standard of feasibility studies is generally acknowledged to have improved in the last decades. Third party reviews rarely have the luxury of enough time and unlimited funds, so where should the reviewers focus their efforts to be most effective? Assuming that the project already apparently meets investment criteria, the authors suggest where and how to look among fundamental project parameters for signs that serious flaws exist that have the potential to become project killers. We also give advice on how to review cost estimates without becoming lost in the details. The paper is supported with numerous actual examples.

Jan 1, 2003

The major incentives for developing continuous processes for the production of formcoke are to achieve a wider range of coals which can be used, greater operating flexibility enabling the production of various coke qualities, and environmental improvements. The characteristics of a formcoke which must be considered when assessing its performance in the blast furnace are compressive strength, abrasion resistance, volatile matter, reac- tivity, porosity, density, size, shape, ash yield and sulphur content. Lurgi's development work in attempting to pro- duce a formcoke which meets the specified requirements has resulted in most current efforts being concentrated on the Bergbauforschung/Lurgi hot briquetting process. This process blends hot char produced from a non-caking coal with small quantities of caking coal in a special mixer in the plastic range of the caking coal. The material is subsequently briquetted hot, then subjected to a thermal after-treatment to produce a strong abrasion resistant formcoke. A 650 tonne per day plant for British Steel Corporation is now under construction. A study of the equipment requirements and the operating costs indicate that the economics of large scale formcoke plants compare favourably with those of conventional coke-making plants.

Jan 1, 1975

By Falconer A. J

Two magnetic parameters are proposed as a basis for the assessment of ironsands beneficiation. The parameters are deter- mined for raw sand prior to dredging and for magnetic separator head feed over a production period of five months. The relationships between these parameters and the performance of the magnetic separators are examined to establish the value of magnetic assessment compared with the traditional soluble iron assay method. The results illustrate that the first parameter, true magnetic fraction (TMF), has a value superior to that of soluble iron when relating raw sand grade calculated by tri- angulation to magnet performance. In terms of the relationship between magnet head feed grade and magnet performance, TMF and soluble iron perform equally as assessment parameters. For the ironsands mined during the five month period, the second magnetic assessment parameter, composite fraction (CR), is shown to merely reflect TMF and offers no additional information for assess- Ment. Conclusions are that true magnetic fraction has many advantages over soluble iron in terms of time and cost of determination and that it is a meaningful and reliable parameter upon which to base all calculations relating to the mining and beneficiation of ironsands.

Jan 1, 1980

By Skaviniak M

Some better perspectives applying to the exploitation and dressing of polymetallic ores in the Banskfa. gtiavnica-Hod- rusea Ore District are supposed to be achieved after a suc- cessful investigation and proving there the existence of deep-seated mineralization as well as due to increasing de- mand for non-ferrous metals and consequently to higher mar- ket prices of those recently noticed. With respect to the present situation in mining and to the further technical development as well, a several times higher exploitation may be in this region expected, especially in the deeper .eated parts of the deposit. When solving the tasks of a complex economic exploitation over the whole region, consi- derable attention is paid to regional relations and impact studies (due to expected exploitation and ore dressing but also to very difficult problems of dewatering (drainage pro- blems-). It will be first of all necessary to find there an equilibrium between the consequences resulting from the re- naissance of mining industry and environmental requests un- dispensable for the city of Banska 9tiavnica and the other neighbouring towns in the vicinity of mining plants.

Jan 1, 1988

By Watson DF

Calculation of the amount of metal in an ore deposit or mining block should be approached by multiplication and integration of appropriate numerical manifolds describing the spatial distribution of the relevant variables, viz. grade, specific gravity and also thickness for bivariate data. Construction of a numerical manifold necessarily involves some form of interpolation but detailed characteristics of this are often not specified in various automatic methods, some of which even provide manifolds with discontinuities. A manifold used in calculations should describe in a geologically plausible way the spatial distribution of the variable of interest. Different approaches to the problem are discussed and compared. Particular computational inconsistencies emerge when "accumulation" is used as a variable in calculations of average grade. If an ore deposit is variable in relation to its sampling and especially if selection of mining blocks according to grade cut-off is a necessary operational decision, the biases introduced by accumulation methods can bring about serious problems of over-evaluation. Modern computational techniques make unnecessary the use of accumulations; because of potential inconsistencies it would seem unwise to use them in any ore reserve computation.

Jan 1, 1987

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By Ranklin W. J

The mechanism and rate-limiting step of carbonaceous reduction of zinc from slags was investigated in the laboratory. Disks of graphite were rotated in ZnO-containing slags at various speeds for fixed periods at 1250 to 1325¦C. The mass loss was used as a measure of the amount of ZnO reduced. Application of the Levich equation indicated that at rotation speeds at which it is valid, the reduction was chemically controlled with an activation energy of 27 kcal/mol. At zero rotation speed the reduction of ZnO by carbon appeared to be slag-phase mass transfer controlled with an activation energy of 38 kcal/mol. An increase in the FeO content of the slag increased the rate of reduction while an increase in sulphur content decreased the rate of reduction. When FeO was present in the slag, reduction appeared to occur by a combination of indirect reduction of ZnO by carbon and by reduction by FeO with reduction of Fe203 back to FeO by carbon. The effect of sulphur was consistent with a surface blockage mechanism due to the surface active nature of sulphur in slags.

Jan 1, 1993