Search Documents

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E Nettleton, A Melkumyan

A probabilistic system for autonomous tracking of excavated ore in mining would be highly valuable. Currently, mine sites can have a vast array of sensors; examples include excavator load cells, bucket volume estimators and haul truck strut pressures which can be used to gather information about the excavated ore at different locations. These sensors can be utilised efficiently to increase the accuracy of mine estimates by introducing a real-time ore tracking system. This requires the introduction of a probabilistic ore tracking framework to consistently fuse information from any sensor input. Current modelling practices are manually intensive, deterministic (no recognition of the quality of data) and generally not a complete end-to-end system. This paper will provide a novel method for tracking extensive ore properties (mass, volume) and intensive ore properties such as chemical composition (eg Fe per cent, SiO2 per cent, Al2O3 per cent). This method is proved to ensure that correct correlations between states are conserved as material is transferred, combined and/or separated at different locations with any configuration of sensor inputs. This ensures that consistency of estimates is maintained and other benefits such as real-time probabilistic reconciliation can be implemented. A method for combining material of different mass and chemical compositions is also developed to enable accurate and efficient operation of the system. Representative experiments on a small-scale and a larger field trial which mimic the mining processes of excavation, haul and unload to ROM Stockpile will be used to verify the approach.

Sep 26, 2011

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

By L. R. MURPHY

This paper gives a general description of mining operations at the Rosebery Mine and a brief account of the older Hercules Mine. The more unusual aspects of the operations, such as the sinking of the inclined shaft, blast-hole experiments, diamond drilling practice, and proposed future developments are described in detail.The following main heads are used:Roseberry- General production Data.General Description of Ore-body, and Characteristics of Ore and Country Rock.Layout of MineMining Methods, Filling, etc.Blast Hole Stoping.Sinking Main Inclined Shaft.Mining Timber. Contract System.Diamond Drilling and Sampling.Surveying.Labour Force.New Developments, Sand Filling and Pumping.Hercules-Situation of Mine.Transport-Haulage and Aerial.Ore Bodies.Stoping Methods.Ore Handling.

Jan 1, 1949

By D Finn, D Kentwell

Experience has shown that the E-Type multiple indicator kriging (MIK) estimation technique often works well for resource estimation in stockwork mineralisation that contains a mixture of high and low-grade mineralisation types that are difficult or impossible to separate spatially. E-Type MIK, like ordinary kriging (OK) is a smoothing estimator and where data is sparse can result in estimates of grade tonnage curves that do not reflect the true block variability at selective mining unit (SMU) scale. The rank and replace (RR) estimation methodology is designed to reproduce both local block accuracy and true block variability at SMU scale and has shown good results when used with highly skewed unimodal diffusive style mineralisation. This paper examines the use of RR with mosaic style mineralisation typically found in stockworks via a case study using real data from Newcrest’s Telfer West Dome deposit. Resource level estimation results for ordinary kriging (OK), E-Type MIK and RR are compared to close spaced grade control models as the reference reality.Results show that stationarity requirements and declustering can severely impact on the usefulness of the rank and replace technique and that it should only be used where trends are not too strong and data are relatively uniformly spaced. This does not rule out its application to stockwork or mosaic style deposits. However, in this case, the presence of trends and different data densities requires the non-stationary domain to be further broken down into sub domains for the RR technique to be effective.CITATION:Kentwell, D and Finn, D, 2017. Testing new estimation techniques – rank and replace: a stockwork case study, in Proceedings Tenth International Mining Geology Conference 2017, pp 365–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By J Kinal, P Steinier

A considerable volume of work exists in the literature examining the electrochemical interactions between grinding media and sulfide minerals. Broadly, most sulfide minerals are more noble than forged steel grinding media used during comminution, therefore a galvanic couple between the media and the sulfide mineral(s) exists, which increases the corrosion rate of the grinding media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulfide minerals thereby affecting their floatability. This paper explores the science behind these corrosion reactions, and provides an explanation of their impact on the pulp chemistry of sulfide mineral slurries and subsequent flotation behaviour. A number of laboratory and plant case studies are used to illustrate the benefits of changing to a more inert grinding media.

Jan 1, 2005

By P Standish

Qualitative risk assessment methods are not well suited to considering complex systems and potential interactions of new technology. As part of supporting tier one mining organisations and international industry groups, the author and colleagues have innovated processes to help provide better solutions to sites/companies considering a move to implementing proximity detection and collision avoidance systems. The process identifies required operating states for the system. By applying a combination of research and team-based analyses, a rigorous identification of credible failure modes which could cause these states to be lost, is identified. Finally, required business inputs, expressed in practical terms are distilled from regulator, industry, organisation and site in a way which clearly addresses the failure modes and so retain the required operating states. These business inputs identify improvements for site arrangements (EMESRT levels 1 to 7) before identifying functional requirements for technological collision avoidance solutions (levels 8 for advisory and 9 for autonomous). The paper presents a case study synthesised from multiple sites analyses and will provide guidance on where to find additional resources to assist in making the best possible transition to better equipment and road network solutions.

Jun 22, 2022

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By C Jones

When the Paulsens operation was poised to be placed on care and maintenance, Bill Beament and the rest of the Northern Star Resources (NSR) team capitalised on the opportunity to send the Ashburton region’s only operating gold mine into the record books.A three-stage strategy was devised by NSR to pay off the acquisition and maximise the return from the operation. The first stage was to mine the 55 000 oz mine plan and pay off the cost of the acquisition, then maintain profitable production beyond the seven months and re-establish a mine life. The second stage involved an early commitment to a 220 m long diamond drill drive being placed in the hanging wall of the orebody from which the extensions of the orebody could be further explored, allowing the second stage of the plan to come into effect and extend the mine life by converting Inferred Resources into the mine plan. The third stage of the initial plan was to utilise this drill drive and continue to drill deeper holes beyond the current limit of drilling in the ore zones to extend the orebody and increase the mine’s life.With an ever growing desire to further expand, the young company took on the bold move of establishing its own mining services division. A critical element to the success of this was ensuring that the right people were recruited with the appropriate specialised skill sets.Aligning common goals amongst all NSR team members, from the board and senior management to the work force on site, was critical to integrate the new and driven direction that Paulsens had adopted. It was essential to change the focus and a shift in all employees’ attitudes and values from a mine that was all but down and out, to a site that wanted to be kicking some serious goals.Teaming together a passionate and driven leader with a strong allied workforce was always going to put NSR in the best position possible to make Paulsens the success story that it now is. But without the calculated risks and enthusiastic attitude, the little known mine site in the Pilbara might have remained just that.CITATION:Jones, C, 2014. The Paulsens transformation – a shining light under a northern star, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By M Edhammer

In 2007, Atlas Copco introduced an integrated tunnel scanner/profiler. The tunnel scanner, which is integrated into the control system, is mounted on the drill rigs, and replaces the previous variants of non-integrated scanner equipment. The Atlas Copco Tunnel Profiler, which is the name of this system, is currently being used by several contractors and mines on various projects in Scandinavia, Finland and Australia. Atlas Copco Tunnel Profiler can scan a tunnel of 65 m2 in just five minutes and is integrated with the computerised control system for the drill rig. This integration means that the results of scanning are immediately available for analysis on the computer screen both in the drill rig and in Tunnel Manager; a software for tunnel and drift planning.In 2008, a method was introduced for locating the drill rig with a total station navigation (TSN) system, integrated into the control system. TSN systems are used by a number of contractors in Scandinavia and Finland, as well as elsewhere in the world. Using a TSN for navigation is in itself not new, but when this is integrated with the control system it provides the opportunity for individual drill rig operators to use this method, without the direct assistance of a surveyor. TSN gives a very precise indication of the drill rig’s position in relation to the tunnel design. An accuracy of ±1 cm compared with the ±10 cm which is normally obtained with the traditional method using tunnel laser and sight plates on the drill rig’s feeder. The closer a tunnel is blasted to its planned profile, potentially the more is saved in terms of less shotcreting, extra rock bolting and other corrective work. A better quality tunnel is the key to better overall economy and today’s technology makes it possible to achieve that goal in every type of tunnelling and mining project.In addition to total station’s ­navigation and Tunnel Profiler, the concept of ‘high precision tunnelling’ also includes:•Software tunnel planning: Tunnel Manager, Tunnel Manager Pro and Tunnel Manager Measure while drilling.•Measurement While Drilling (MWD)collects the various drilling data and the interpretation of these for the early identification of variations in the rock.•Rig Remote Access (RRA) is a support for wireless or wired communication between drill rig and planning office. The result is being able to send planning data to the drill rig and to simultaneously have the facility for logged files to be sent from the rig to the office. There is an option of an external computer logging in to the drill rig’s control system to view menu screens and settings, and remotely troubleshoot and plan appropriate action.

Mar 21, 2011

By T Day, I G. Robertson, G J. Lyman

"Various approaches are used in the industry for establishing procedures (sample mass estimation and method of subsampling) for sampling and analysis of gold ores. The key factors that determine the accuracy of the results that can be expected for a given set of procedures are widely misunderstood.Recent developments in sampling theory show that the estimation of the accuracy that can be expected for a given gold ore as a function of sample mass is actually a simple matter. For a given sample mass, the accuracy that will be achieved depends only on the grade of the ore and the range of masses of the grains of the gold in the ore. This, of course, demands that a reasonable estimate of the distribution or spread of gold grain masses in the ore be known. But this is something that should be known if the gold is to be efficiently recovered in the processing plant.This paper provides a simple explanation of the real facts about sampling of gold, either in the field or in the plant, and provides results for a number of cases of combinations of fine and coarse gold in an ore. The prerequisites for accurate gold sampling are:correct sampling with no loss of sample or contaminationsample preparation procedures that recognise the impact of the gold grain mass spreadpractical analysis of the sample masses required to provide acceptable accuracy.Issues of corporate governance are also discussed.Citation:Lyman, G J, Robertson, I G and Day, T, 2016. The Simple Facts about Sampling Gold Ores, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 159–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J G Bastias

It is sometimes necessary to resort to extremes in order to call attention to something that is pertinent to safety in mining. When some of the experts in occupational safety talk about this topic, they usually refer to a 'regulation' established by the Romans which stated that, due to the health hazards, usually death, no Romans but only slaves should work in mining. Since the time of the Roman Empire, a lot of ground has been covered in the field of mine safety. Nowadays, it can be said that occupational safety is being seriously addressed, with the result that the number of mining accidents has reduced dramatically, fatalities in this industry are less frequent, and the rate of accidents compared with other activities, such as construction or fanning, is low. This achievement has been possible initially through government legislation and by procedures established by the mining companies themselves. However, the dilemma for government is whether to regulate and if so, how much. It is pleasing to observe that most companies are establishing working procedures which conform with new government legislation, placing strong emphasis on the duty of care for mine employees. There will always be some regulatory aspects of legislation, and perhaps the best example of this is in the use of mine hoists where there are no international or Australian standards, and the regulations applied are of an empirical nature that err on the side of safety.

Jan 1, 1994

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By S Servant

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the stope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the stope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this mine.

Jan 1, 1998

By T Dawson, B Haskins

Fatigue is it the newest buzz word or is fatigue a real phenomenon that is creating safety and organisational risk for you? There is no debate that fatigue is natural, and it affects us all, just like gravity; however, there has been much debate on the severity of its impact in the workplace. For many years the impact was not measurable, hidden out of sight and, quite frankly, written off as the infamous ‘operator error’. Over the last several years, advancements in technology have provided safety and health professionals, sleep scientists, fatigue experts and organisations with the ability to monitor and detect fatigue events in real time, as well as predict and monitor increased risk for fatigue events. Caterpillar Safety Services has assembled an extensive and exceptional set of technologies that will provide the best methods and data to measure the impact of fatigue. This paper will discuss fatigue in the workplace and review the technologies and data sets available, which will allow the reader to determine whether this risk is real or rubbish.CITATION:Haskins, B and Dawson, T, 2017. Fatigue risk in your operations – real or rubbish? It actually depends , in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010