Search Documents

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Fraser, M Scoble

Within the past decade, incidents of mining–community conflicts have grown dramatically and represent one aspect of a phenomenon known as social risk. Research published in 2014 indicates that a lack of social acceptance is now a leading and costly cause of delays for mining projects.The rise of social risk, complemented by the need to earn the trust of an increasing number of stakeholders so that mining projects can be developed effectively, is problematic for the industry. Conflicts are occurring in situations where companies are fully compliant with regulatory and legal requirements, despite initiatives by mining companies to earn social acceptance and despite the proliferation of tools to support corporate social responsibility. Intensifying the impact of social risk is the fact that it has increased during a time in the global mining sector when companies have had to grapple with declining commodity prices, increasing capital costs and debt levels and the challenges of mining lower-grade deposits.This paper will explore a hypothesis that in today’s interconnected society, social risk in the mining sector constitutes a legitimate business risk that must be managed strategically. The reality facing mining companies is that information, once considered confidential, now travels quickly on social networks and via a growing number of groups and individuals that have earned a legitimate right to be classified as stakeholders in projects that affect their communities. To be successful, it is suggested that companies will benefit from increasing internal collaboration and providing training to equip teams to mitigate social risk to mining projects and protect reputation capital. The paper is based upon PhD research being undertaken to assess the points of intersection between social risk and social responsibility during the construction stage of greenfield mining projects.CITATION:Fraser, J and Scoble, M, 2015. Mining–community conflicts – can the future mining sector transform social responsibility?, in Proceedings Third International Future Mining Conference, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By S Dunham

A cross-discipline approach combining geology, metallurgy and mine planning, geometallurgy is seen as the next logical advance in improving the design and operation of mining businesses. This rapidly evolving field is focused on realising the value that has often been lost in the chasms between the aforementioned technical silos. When successful, the geometallurgical approach promises the ability to tailor mining and mineral processing development and operational options more closely to the characteristics of the resource with resulting lower costs (both capital and operating), improved recoveries and fewer project failures.As with any technological (or managerial) change, there will be side effects from the success of the geometallurgical approach that will impact areas beyond obvious linkages between geology and processing. Some of these effects have the potential to be beneficial to the resource industry and society in general. Beyond the basic geometallurgical promise of closer alignment between processing design/strategy and the multivariate 3D spatial characteristics of the mineralisation, this paper discusses the broader implications and ramifications of the emergent geometallurgical approach: enhancing exploration and discovery; improving project development success; achieving sustainability in an industry working with non-renewable resources; in a world of increasingly hard won license to operate, improving the management of potentially harmful by-products and waste materials (with knock on effects for proactive management of closure issues); smarter approaches to energy management and thus optimisation of projects with respect to carbon footprint; and potential to re-value assets and thus realise a strategic advantage in the area of acquisitions, divestments, mergers and take overs. The authors strongly believe that companies that actively engage with the above issues (and ensure that technical efforts in the area of geometallurgy are not isolated from the larger value chain activities of the firm) will be able to exploit the opportunities that consequentially arise. These early adopters will gain first mover advantages. Firms taking the broad view of geometallurgy will have an opportunity to maximise stakeholder value and win greater success than their less insightful competitors.

Sep 5, 2011

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By S Thacker, M Noakes

The Newmont Tanami Operations (NTO), formerly the Granites Gold Mine, commenced operation in the mid-1980s with tailings deposition evolving over the past three decades as production has increased and the operation has expanded. Paddock-style tailings storage facilities (TSFs) and in-pit tailings deposition have fulfilled the tailings requirements for NTO over its lifetime with the technical specifications of these facilities improving over time in line with the positive development of standards, guidelines and best practice.This paper reviews the options for tailings storage facilities at NTO and the many considerations that have been analysed and deliberated upon before settling on specific TSF types and designs. It also explains the operating philosophies of the tailings deposition and how the facilities have always strongly maintained the optimum capture and retrieval of water. The current TSF design and criteria is presented, along with the introduction of dry tails harvesting for use in paste production as a backfill product for the underground mine. Tailings deposition and recovery remains a critical function of the Granites process to ensure long-term operation and gold production.CITATION:Thacker, S and Noakes, M, 2015. Newmont Tanami Operations – tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B D. Burford

High intensity stirred milling using the IsaMill has been the enabling technology for many projects by transforming the economics of fine grinding and simplifying circuit design. IsaMill grinding technology was originally developed for large-scale grinding to P80 sizings of 7 ¦m. The IsaMill is a high throughput, high efficiency mill that produces sharp product size distributions in open circuit configuration. The ability to grind in an inert environment, using a wide variety of media types, can give further metallurgical and economic benefits. The high energy intensity results in a small footprint that enhances the ability to distribute grinding power throughout the circuit, applying grinding energy to the minerals that need it. Recent scale up developments in IsaMill technology have enabled the benefits to be extended to large-scale conventional grind sizes, until now the domain of ball and tower mills. This paper will examine the crossover of IsaMill technology from ultrafine applications into the more conventional grinding area (P80 20 - 150 ¦m). Scale-up developments in IsaMill technology that have enabled this are reviewed. The upcoming commissioning of a 3.0 MW M10,000 IsaMill, the most powerful to date, grinding to P80 55 ¦m at PPL in South Africa will be discussed, as will the recent commissioning of a 2.6 MW M10,000 IsaMill at Kumtor. Recent testwork at McArthur River, where an IsaMill is being considered as an addition to the primary grinding circuit to replace the current tower mill will be reviewed. The potential combination of HPGR and IsaMill to transform concentrator grinding economics will also be discussed. Large-scale IsaMill technology has the ability to transform circuit design and energy efficiency for both coarse and fine grinding.

Jan 1, 2006

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

By D J. Brake

In most underground mines, the ventilation system is a significant portion of the total mine capital and operating cost and the largest consumer of underground electrical power. The effectiveness of the ventilation system has a major bearing on the safety, health, comfort and morale of underground personnel, and has a critical role in meeting production targets and therefore business revenue. Perhaps the most important component of the primary ventilation system is the primary fan. Correct performance testing of the primary fan during the warranty period is important not only to ensure the mine has obtained the asset that it paid for and can therefore deliver on the fanÆs crucial safety and economic role in the future of the mine, and to provide a justification for releasing final performance warranty payments to the supplier, but also to provide a benchmark or baseline against which to assess future performance issues. As there are at least three potential international standards available to measure fan performance, there has been considerable confusion regarding which of these to use for testing primary mine fans, and also the correct allowances and tolerances to use. This paper provides guidance on which standards to use for different applications, how the standards should be interpreted, what allowances and tolerances are reasonable, and other important issues to be resolved with the fan supplier prior to making a contract award. The paper also discusses practical issues and methodology for in situ primary fan performance testing.CITATION:Brake, D J, 2013. Performance and acceptance testing of main mine ventilation fans, in Proceedings The Australian Mine Ventilation Conference , pp 141-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By C F. Stokes

The Trident Gold Deposit has been successfully developed by Alacer Gold (formerly Avoca Resources Limited) into a 1.3 Mt/a operation in the space of four years from discovery to first gold pour (2008). The current in situ Resource for Trident is estimated to be 5 900 000 t @ 5.0 g/t for 940 000 ounces at a cut-off of 1 g/t or 2 g/t depending on ore style. Production to date (Alacer and previous owners) is in excess of 500 000 ounces. The deposit lies towards the southern end of the Norseman-Wiluna Greenstone Belt in the Archaean Yilgarn Craton, where it is centred on the historical Higginsville Mining Centre, midway between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz). Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (Eastern Zone, Western Zone and Apollo) hosted exclusively within the gabbro; and thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed primarily at sheared lithological contacts between the various mafic and ultramafic lithologies. The initial interpretation of the Trident Deposit was based on steeply-dipping structures controlling the zones of mineralisation, with much of the targeting and drill-testing aimed at this style of orebody. Subsequent exposure of the orebodies has identified a series of shallow-east dipping mineralised systems (interpreted to be large reverse shears) that at their intersection with the steep-dipping structures cause significant gold enrichment. It is postulated that both orientations are primary fluid pathways with the intersection between the two resulting in zones with significantly high concentrations of gold mineralisation (in excess of 300 000 ounces). This new understanding on ore controls at Trident has identified that the thin lode-style shear-hosted laminated veins are continuous for over 1700 m along strike as they step en echelon down-plunge. In addition, a repetition and periodicity to the intersection between these steep dipping lode-style systems and the shallow-dipping mineralised zones (estimated to be 700 - 900 m down-plunge) has been identified which has considerably increased the down-plunge potential of the Trident Deposit.

Aug 22, 2011

By D Cooke

In 2010, Kalgoorlie Consolidated Gold Mines (KCGM) was Australia’s largest gold producer, with total annual production of 788 000 ounces. Of the gold produced by KCGM in 2010, 95 per cent was extracted from the Fimiston open pit, also known as the Superpit. The Fimiston operation encompasses the historic Golden Mile, from which more than 55 million ounces of gold have been extracted from the world-class Fimiston lode style mineralisation.The operational performance of the KCGM Fimiston open pit was reviewed for the period between 2005 and 2010. Key performance metrics reviewed included mined tonnes and grade, cost per ounce of gold produced and the mine to mill reconciliation trends. The years 2007 and 2008 were characterised by a decline in performance against key performance metrics. The ore zones were diluted, with the excess tonnes mined resulting in lower grade and an increase in the cost per ounce. Poor reconciliation between ore mined, the ore reserve model and the grade control polygons was also observed.A series of improvement initiatives were implemented in late 2008. As a result of changes made to the grade control and mining practices, the site performance recovered. Unplanned dilution was reduced, which had a positive impact on mined grade. The lower tonnes combined with higher grade reduced the cost per ounce to below budgeted levels in 2009 and 2010, enhancing the profitability of the operation. The operational performance between 2005 and 2010 was compared to the turnover statistics for the KCGM geology department over the same period. Turnover accelerated between 2005 and 2007, peaking at an annualised rate of 43 per cent. With the onset of the Global Financial Crisis and the implementation of retention initiatives, turnover reduced significantly between 2008 and 2010. A strong consistent correlation was observed between the turnover trends in geology and the performance of the grade control function and resultant site metrics.The cost of turnover is known intuitively, however, rarely quantified. To evaluate the benefit of the improved performance, a detailed financial model was used to quantify the impact of the grade control function. In 2010, the headgrade exceeding budget by just four per cent contributed an additional A$24 M of value to KCGM. In contrast, if the 2008 performance had been replicated in 2010 (-9 per cent on headgrade), the result would have removed A$61 M in value from the business. The KCGM experience between 2005 and 2010 demonstrates the value of human capital in a mining operation and the importance of a high performing geology grade control team to the profitability of a mining operation.

Aug 22, 2011

The Committee for Mineral Reserves International Reporting Standards (CRIRSCO) was formed in 1994 to promote development and adoption of international standards for estimation and reporting of exploration results, mineral resources and mineral reserves. The CRIRSCO standards have been accepted by most mining companies and professional societies worldwide. Market regulators from Australia, South Africa and Canada require that these standards be followed when releasing public information. Among these requirements is the use of specific definitions for what constitutes exploration results, mineral resources and mineral reserves. If such information is publicly disclosed in must be estimated by a Competent or Qualified Person. In the United States of America, public disclosures are regulated by the US Securities and Exchange Commission. The SEC does not recognise the CRIRSCO guidelines, and some of the SEC requirements for public release of information are materially different from those applicable in other countries. The CRIRSCO definitions and the Competent Person requirements are reviewed and compared with those of the SEC. The organisation of the SEC and its rule making process are briefly discussed. Ongoing efforts to bring the US regulatory requirements closer to those applicable in other countries are presented, as well as other activities that CRIRSCO is entertaining with the United Nations, the International Accounting Standard Board and other international organisations to reach the objective of worldwide standardisation of reporting procedures.

Jan 1, 2006

By T O&apos, Sullivan

Reconciliation of metal production from a sublevel cave (SLC) mining operation is a complicated process. SLC reconciliation is unlike reconciliation for open stope operations, where a tonnage of extracted ore can be assigned to an exact volume of in situ ore, and a direct comparison made between the estimation of contained metal and actual metal production. In SLC operations the ore extracted from a particular SLC drawpoint will be composed in part from the parcel of freshly blasted in situ material, in part from varying components of ore material (from cave stocks) flowing down from other previously mined areas vertically above the current draw position and in part from external dilution. This leads to difficulties in reconciling production grades against estimated grades. The problem is that we know how much metal we have produced but we can not precisely say where it has come from. Metal production reconciliation is fundamental in assessing ore reserve estimation accuracy and performance and in determining a draw management strategy for SLC mining. In terms of contained metal, differences in extracted metal compared to in situ metal represent changes to cave stocks. To generate local estimates of the cave stocks, differences in metal for each ring are treated as additions to or subtractions from a series of vertical columns of stocks extending throughout the height of the cave. The sum of metal differences (extracted versus in situ) for each vertical column results in a residual metal map at any particular mining level. The metal maps show areas where the metal production has been greater than or less than expected. The maps also highlight areas in the cave where residual metal is located, areas where targeted overdraw can reduce cave stocks.

Jan 1, 2006

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990

By R Hindstr÷m

The demand for iron ore has increased dramatically in the last years and is forecast to remain on a stable high production level for years to come. ItÆs expected that the world economy is facing a stable continuous growth of iron ore to two billion tonnes and more over the next decades (Beddows, 2007). Furthermore it is expected that the existing and known high-grade ore resources will decline, and the iron ore industry will be forced to implement more and more advanced beneficiation plants. As a consequence of the more complex beneficiation requirements, there will be a need for modern solutions for iron ore dewatering that are reliable mechanically as well as cost effective and with high capacity per unit at the same time. Conventional vacuum filtration methods have been the most prevalent in fine iron ore dewatering. Product quality needs, lower ore grades, complex mineralogy and energy costs have resulted in iron ore producers seeking better solutions for dewatering, in particular pelletising feed. New advanced filtration methods have been introduced to the market. This paper describes how these modern methods are answering the needs of the industry. Performance of advanced dewatering technologies (pressure filtration and ceramic capillary action filtration) for iron ore applications has been studied, and the findings are based on both industrial and pilot scale experiences on different materials. For example, the results show that the cake moisture content of iron ore pelletising feed can be optimised more effectively by using modern filtration technologies. By selecting the most suitable and adjustable equipment, the effects of variations of feed material on downstream processes can be minimised and the possibilities of processing more difficult raw materials to high-quality pellets are better. The Larox Corporation develops, designs and manufactures industrial filters and is a leading technology company in its field. Larox is a full service solution provider in filtration for separating solids from liquids. As such, this paper compares the new developments in this market area with the prevailing known vacuum filtration technology, but focuses on a comparison between capillary action filters and rotary vacuum disc filters (RVDF). The trade name CeramecG is used to differentiate the Larox filter from the generic term.

Jan 1, 2007

By Gale D. C, Giles D. E, James Parker A

A zinc-lead-iron sulphide concentrate from McArthur River can be leached at atmospheric pressure in aqueous solutions with HCI, FeCl3, CuCI2, HCl/02 HC1/02/ CuCI2, Cl2, and CI2/CuCI2 to extract >98 per cent zinc, >90 per cent silver, and <15 per cent iron in 1-7 h at 95°. Galena is more reactive than sphalerite and is converted to lead chloride. Except for leaching with HCI, elemental sulphur is the the main by-product of the leach with little or no sulphate ion detected. The rates and products of these reactions are compared. It is recommended that aqueous slurries of the concentrate (50 per cent w/v) are leached at atmospheric pressure with Cl2 in the presence of copper(II) chloride, which accelerates the extraction of zinc. Hydrochloric acid is a by-product which is consumed bYJeaction with fresh concentrate in air at 60°. Copper is subsequently stripped from the leach solution and recycled by reaction with fresh concentrate at 100°. The separation, recovery, and electrolysis of zinc and lead chloride is outlined since this process would produce Cl2 gas which can be recycled and used directly in the leaching stage.

Jan 1, 1976

The banded iron formations "jasper bars," jaspilites, banded hematite quartzites or banded ironstones, etc., as they have. variously been termed in Western Australia, constitute one of the most striking features of the Pre-Cambrian in this State. They occur in at least two distinct divisions of the Pre-Cambrian, viz., in horizons interbedded with quartzites, shales and thin bedded dolomite in the N~llagine (Proterozoic) Series; and amongst the Older Pre-Cambrian rocks, associated with the metamorphosed sediments of the Jimperding-Chittering Series, the Yilgarn Whitestone Series and the Mosquito Creek Series, and interbedded with metamorphosed basic lavas, tuffs and sediments of the Older prenstone or Kalgoorlie Series.In the Hamersley Ranges in the north-west of Western Australia banded ferroginous cherts are well developed amongst the horizontal sediments of Nullagine Age. These iron formations have recently sprung into prominence as they have been found to form the host rocks for important deposits of· blue asbestos. They are closely comparable with the unique crocidolite-bearing banded ironstones of the Cape Province, South Africa, and have been described elsewhere in some detail by the writer. (1) t .The banded iron formations with which it is intended to deal principally in the following pages, form most abundantly in the Central and Eastern Goldfields of Western Australia where they form portions of the Older Greenstone or Kalgoorlie Series of auriferous rocks. In these regions their chemical inertness and physical hardness provide considerable resistance to the agents of erosion and consequently they frequently stand out in strong topographic relief in otherwise monotonously flat or gently rolling country. These banded-iron formations have proved of considerable direct economic importance in the goldfields and in other portions of the State because of thei!! associations with 'gold, iron -and to' a lesser extent, manganese; whilst indirectly because of their peculiar nature, form and topographic prominence, etc, they have been of tremendous assistance to the field geologist both in the practical application of methods of geological mapping and in the' elucidation of geological structures. Finally, they have recently acquired a new importance in the specialised search for ore-bearing lodes or for structural information over areas of soil-covered country, as their form and composition make them ideal subjects for the use of either electrical or m!1-gnetic methods of geophysical prospecting.

Jan 1, 1941

Mining epitomises the challenge of sustainable development, because few sectors have such a direct impact on the natural environment, yet few are more important to the economic and social health of almost every region in the globe. In a global industry, with increasing competition for exploration and mining investment dollars, sustainable development must also be resolved within an international competitiveness framework. In formulating a response to the challenge of sustainable development, the State and Federal Governments do not fully appreciate the extent to which technology drives the solution on a range of issues. In some cases` a dangerous fatalism about the state of science has led to an unhealthy æstop productionÆ attitude that puts our industry and economy at risk. As a technical institute representing the professionals in the minerals sector, The Australasian Institute of Mining and Metallurgy (The AusIMM) sees one of its roles as being to highlight the way in which industry innovation can facilitate solutions. The AusIMM is currently evolving a greenhouse gas emissions policy. As a case study it throws into sharp relief the way in which irresponsible ælimits to growthÆ policies could have a negative impact on the sustainability of the sector, as well as the importance of a technology- based solution. With 80 per cent of greenhouse gas emissions in the next twenty years projected to come from developing economies, such as India and China, major reductions will only be achieved if cost-effective, low emissions energy technologies are deployed in developing countries, and more energy efficient processes of producing key commodities for them are brought online. As a supplier of the key energy resources and materials that will be in high demand to feed developing economies, and with knowledge intensive industries with excellent R&D links across mining and manufacturing, Australia is well positioned to contribute to develop key low emissions technologies. However, we will only be able to take advantage of this position if the Federal Government commits to a holistic greenhouse emissions policy that does not penalise industry. We need effective æpushÆ polices aimed at leveraging investment in low emissions R&D that are closely linked in to æpullÆ policies aimed at stimulating technology uptake.

Jan 1, 2006

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

By T de Wit, S Meyer

The location of seismic events in mines is traditionally calculated based on the arrival times of P- and S-waves for a given velocity model (homogeneous or heterogeneous). This technique is successful when the sources of seismic events are sudden and localised (eg episodes of fracturing in solid rock or dynamic slip along a plane of weakness) and thus the radiated seismic waves have clear arrivals. In massive mining operations such as block caves, strong seismic signals often originate from the movement of loose rocks on the perimeter of the fracture zone. These signals are easily recordable but do not contain easily identifiable direct P- and S-waves, making the estimation of location through traditional methods more complicated. This problem has been approached by using a ‘brightness’ location method that estimates the origin of seismic waves based on travel times of envelopes of seismic energy. This tool is extended to be applicable in a heterogeneous velocity environment that now accounts for the presence of a cave or other strong velocity perturbations. The suggested method is particularly important when caving occurs in low-stress environments (eg close to the surface).CITATION:Meyer, S and de Wit, T, 2016. Location of seismic events associated with caving using brightness method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 225–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016