Search Documents

By G Byrne, A Bowden

There is often a difference in opinion about the allocation of risk in the establishment of mine closure bonds or financial assurances. From the State’s perspective, protection is needed to ensure that the broader community is not left with the liability of properly closing a mine in the event of a default by the mine operator. Such a default might occur where an operator decides to abandon a site, perform incomplete rehabilitation, becomes insolvent or claims limited liability. On the other hand, mine operators who can demonstrate a strong financial position plus a record of social and environmental commitment and performance, argue that there should be some recognition of this in setting a bond that is less than the full cost of early closure. They argue that a mine rehabilitation bond based on the full cost of early closure is overly conservative and ignores the actual risk of the operator being in default. This paper examines an approach that incorporates the risk of default into the establishment of mine closure and rehabilitation bonds. CITATION:Bowden, A and Byrne, G, 2018. Mine closure bonds (financial assurances) – the ‘how much?’ conundrum, in Proceedings Life-of-Mine 2018, pp 32–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Nakahiro Y, Wakamatsu T

In the present study, from experimental results, a new concept of possibility of flotation separation of quartz from feldspar is presented. The effect of the nonionic surfactant Brij 58 on the flotation behaviour of quartz and feldspar has been investigated. The effect of the surfactant adsorption at the solid-liquid interface was also studied. The results demonstrate that maximum flotability of quartz occurred at low concentration of surfactant. Feldspar is not collected by this surfactant. Flotation tests with feldspar that had previously been subjected to leaching by hydrochloric acid yielded similar flotation response as that of quartz. The effect of removal of alkali cations from feldspar surface on its flotability was investigated. The effects of inorganic and organic additives on the flotation recovery of quartz are discussed in terms of the slating-out or salting-in properties of these additives. KEYWORDS: Alkyl polyoxyethylene; feldspar; flotation; nonionic surfactant; quartz; salting-in; salting-out; separation; silanol groups.

Jan 1, 1993

By A K. B Chigwada

Mining organisations grapple with the same problems year after year, wasting incredible amounts of time and money. According to estimates from the International Labour Organization (ILO), over one million work-related deaths occur annually, and hundreds of millions of workers suffer from workplace accidents and occupational exposure to hazardous substances worldwide. Many accident reports cite human failure as a primary cause (Busse and Johnson, 1998). The workers at the Bhopal chemical plant pumped methyl isocyanate into a leaking tank (Morehouse and Subramaniam, 1986). On 3 December 1984, more than 40 tons of methyl isocyanate gas leaked from a pesticide plant in Bhopal, India, immediately killing at least 3800 people and causing significant morbidity and premature death for many thousands more. The company involved in what became the worst industrial accident in history immediately tried to dissociate itself from legal responsibility (Broughton, 2005). Australia is not spared from safety problems either (Lucas, 2022). The ILO Convention 176 (1995) as a response provides that national law should inter alia provide for the supervision of safety and health in mines; the inspection of mines by designated inspectors of the competent authority; the procedures for reporting and investigating of fatal and serious accidents; the compilation and publication of statistics on accidents, occupational diseases and dangerous occurrences; the competent authority to suspend or restrict mining activities on safety and health grounds until conditions giving rise to the suspension are addressed; and worker consultation on matters related to safety and health in mines. This has assisted in getting enough data to define the magnitude of the problem to the mining sector.

Apr 16, 2024

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By J H. Park, R R. Kim, H S. Park, H J. Kim

This study focuses on the recovery of valuable metals, specifically silver (Ag) and palladium (Pd), from copper-containing sludge (with copper content less than 20 per cent) generated during PCB processing and from spent petrochemical catalysts used in vapour decomposition during oil refining processes. The present results indicate that an increase in the mixing ratio of alumina-based spent catalyst leads to a decrease in the recovery rate of Ag and Pd. The recovery rates for Ag and Pd range from 84 per cent to 96 per cent and 80 per cent to 98 per cent, respectively. This trend is attributed to the increased emulsification of copper droplets containing Ag and Pd in the slag. The emulsification is caused by the decrease in the settling velocity of the copper droplets due to the increased viscosity of the slag as well as by the decrease in the slag-metal interfacial tension due to an increase in sulfur content at higher mixing ratio of spent catalyst.

Jun 19, 2024

Polarization phenomena associated with the use of an agitated bed of particles as an electrode for metal deposition were studied. The concentration polarization at this type of electrode is much smaller than that occurring at a fixed or moving electrode surface. Agitated particle electrodes can be used to electro-reduce copper from solutions over a wide range of concentration and at cur·rent densities up to 2000 AIsq. ft. of bed cross section.

Jan 1, 1971

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

By B Mack

The cost of water treatment is now more than ever a major consideration for maintaining an environmentally and economically sustainable mining operation. As an industry, we often have to consider water sources that are highly impure and difficult to treat. We are also discovering the value of our waste waters in this regard and using new and improved methods and technology to reclaim and reuse water. In many instances, the water or waste water to be treated is highly acidic and saturated in sparingly soluble salts. Conventional systems used to liberate this type of water typically involve high doses of lime with large volumes of waste sludge produced, and are comparatively complex to operate, to pretreat the water in order to reduce scaling tendency on the reverse osmosis stage. However, if the water is considered valuable for reuse, then why not avoid difficult and cumbersome pretreatment processes and treat the water at low pH to keep the sparingly soluble salts, metals and other dissolved species in solution. This paper describes a patented technology that uses and successfully proves this concept as a cost effective option for certain situations. Results from a treatability study on an Australian groundwater are discussed, along with an economic comparison to a conventional method and discussion on full-scale potential.

Jan 1, 2009

By D Beck, E Jones

The measurement and management of deformation in underground excavations is a key responsibility of geotechnical and mining engineers. A critical aspect of these roles is to ensure there is sufficient ground support capacity for the expected demand.Current methodologies for monitoring deformation and ground support serviceability-limits require measuring displacement at distinct points, or using visual observations. These current methods limit the assessment to a qualitative interpretation of deformation across the entire excavation.Recent advancements of Light Detection and Ranging (LiDar) technology permit a new method for monitoring deformation that allow a full 3D image of extended sections of an excavation to be precisely scanned. The results from the comparison with subsequent scans provide valuable information on the magnitude, direction and extent of regions exceeding the ground support serviceability-limits. This new method now provides a quantitative assessment across the entire excavation being monitored.The implementation of regular scanning has been demonstrated to be highly advantageous not only at mines with swelling or squeezing ground, but also at mines with rapid seismic induced deformation. The use of LiDar technology as a routine deformation measurement tool for geotechnical and mining engineers (and further applications) are discussed in more detail in this paper.CITATION:Jones, E and Beck, D, 2017. The use of 3D laser scanning for deformation monitoring in underground mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Whilst employed by Dyno Nobel as the Technical Services Engineer û Brisbane, I was asked, as part of a contractual agreement, to look at optimising PioneerÆs blasting process to provide the most effective rock to the new crushing and screening plant. This paper details the preliminary blast designs and practices that have been in use at the quarry and the initial changes made to these designs, and the effect they have had on the excavation and crusher performance.

Jan 1, 1999

By D Connelly

Silver and gold bearing ore from the Troy Resources NL Casposo Gold-Silver Project, located within the San Juan Province of Argentina contains a complex mix of gold, silver, electrum and silver sulphides in the ore. Casposo is a typical low sulphidation epithermal style gold–silver deposit where mineralisation is hosted within rhyolite – andesite flows and breccias. Veins are typically banded quartz–chalcedony colloform - crustiform banded with quartz - carbonate infill. Mineralisation is associated with an assemblage consisting of quartz, chalcedony, adularia, calcite, illite, sericite and trace sulphides. Gold and silver occur as electrum, native silver, sulfosalts and silver sulphides. This paper presents a case study that describes the process selection, development and engineering of a tailored process plant for the recovery of gold and silver from this ore.The original feasibility study, modelling, metallurgical testwork and engineering studies are outlined. The final flowsheet was based on minimising capital cost, operability, recovery and minimising technical risk.The process flowsheet uses the traditional Merrill Crowe route because of the high silver to gold ratio in the feed and achieves maximum gold and silver recovery while providing a common facility for future ore body treatment.

Aug 8, 2011

The history of the discovery and development of the Kambalda nickel orebody. is reviewed and the decision to process the Kambalda concentrates by the Sherritt-Gordon process at Kwinana is discussed. The Kwinana Nickel Refinery is described and the problems encountered in the first year of operation are Outlined.

Jan 1, 1971

The Bureau de Recherches Geologiques et Minieres (BRGM) (a French Government-sponsored geological and mining agency), through international experience gained over many years, has become very skilled in alluvial prospection, particularly for diamonds. The research laboratories within the BRGM have also been active in creating new mineral processing equipment, some of which is directly applicable to such prospection. One such development, the mobile prospection unit, is described and its application in mineral exploration is demonstrated by a consideration of the diamond search in Australia and the general exploration of the Massif Armoricain (France). Because this latter study was fundamental in the development of the concept of 'mineral-geochemistry', and its application in mineral exploration, it is also briefly described.

Jan 1, 1971

By M Nehring, M Kizil, P Knights

Mining and beneficiation can be described as sequential processes of separation of valuable minerals from waste. There is a great deal of interest in how the industry can be more effective – and efficient – with these processes. In particular, many mining companies are looking towards digital technologies to improve precision mining practices; that is, the targeted identification and separation of valuable ore from waste during the mining process. Greater precision will help unlock the value in many complex orebodies that are currently considered Tier 2 or 3 deposits. CITATION: Knights, P, Kizil, M and Nehring, M, 2018. Selection of precision surface mining methods for complex metalliferous orebodies, in Proceedings Complex Orebodies Conference 2018, pp 31–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By B Levasseur, C Olsen, E Ghasemian Langeroudi, F Larachi, F Safizadeh, C Gagnon

Gold recovery by the cyanidation process is often accompanied by the leaching of other species. This leads to the depletion of the level of free cyanide and oxygen available for gold cyanidation. The largest proportion of the consumed cyanide is diverted by the cyanicides (eg S, Cu, Zn, Fe, etc) into non-valuable complexes.COREMÆs Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during preoxidation and cyanidation. Flotation tailings and single mineral samples such as pyrite, sphalerite and chalcopyrite, along with their different combinations, were analysed to highlight the influence of ore mineralogy on the operating conditions. The effects of different kinds of oxidants (oxygen, hydrogen peroxide, ferricyanide and ozone) and chemical additives (ammonium sulfate) were investigated.Experiments conducted in alkaline solutions reveal that mineralogy is a key parameter since pyrite, chalcopyrite and sphalerite react quite differently during preoxidation and cyanidation. A significant increase in sulfur dissolution, especially on pyrite, was observed by applying preoxidation. H2O2 preoxidation showed a positive effect on increasing sulfate formation, a desirable by-product from the cyanide consumption point of view. Preoxidation of synthetic ores with ferricyanide resulted in boosting thiosulfate formation. Tests conducted on flotation tailings from a polymetallic mine revealed that a short preoxidation increases the dissolution of the ore leading to higher gold recovery and lower cyanide consumption. Regarding the formation of thiocyanate, the most undesirable by-product of the cyanidation, ferricyanide and ozone were found particularly efficient to hinder their formation. Finally, the addition of ammonium sulfate during the cyanidation process showed some promising results in terms of both gold dissolution and cyanide consumption.CITATION:Ghasemian Langeroudi, E, Levasseur, B, Safizadeh, F, Olsen, C, Larachi, F and Gagnon, C, 2013. Optimisation of operating parameters for cyanidation of sulfide-bearing gold flotation tailings in order to prevent the impact of cyanicides, in Proceedings World Gold 2013 , pp 111-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Nakajima A

Some attempts were made to recover uranium from aqueous systems by using various biosubstances including microbial biomass. Of hundreds species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stutzeri, Neurospora sitophila, Streptomyces albus and Streptomyces viridochromogenes. In parallel to this research, various kinds of biomass and commercially available crude drugs were screened to measure their abilities to adsorb uranium. Of these biosubstances tested, high uranium adsorbing ability was observed in chestnut skin, Comi fructus, Geranii herba and Chaenomelis fructus. From these results it may be considered that the uranium adsorbing ability of these biosubstances is due to the following; the uranyl ion is co-ordinated by the polyphenolic compounds such as tannin existing in the biosubstances. Along with these fundamental researches, we have developed a new adsorbent, the immobilised persimmon tannin (kakishibu tannin), for uranium and thorium. This adsorbent can accumulate 1.71 g of uranium per gram of the adsorbent (14 mEq/g), and the uranium adsorbing capacity of this adsorbent exceeds by several times that of commercially available chelating resins (2 - 3 mEq/g). We attempted to recover uranium from uranium refining waste water by using the immobilised persimmon tannin. As a result, the immobilised persimmon tannin can recover trace amounts of uranium from uranium refining waste water containing 10 - 15 ppb uranium with high efficiency. Almost all of the uranium adsorbed onto the adsorbent can be desorbed by washing with 0.05 - 0.1 M HCl or H2SO4. Thus, the immobilised persimmon tannin can be used repeatedly in the adsorption-desorption Cycle.

Jan 1, 1993

By H S. Smit, P Lotz

Gold mining companies who are signatories of the International Cyanide Management Code (visit www.cyanidecode.org for further information) are required to measure WAD cyanide on-line and destroy WAD cyanide in excess of specified limits. Weak acid dissociable (WAD) cyanide refers to those cyanide species liberated at a moderate pH of 4.5 such as HCN(aq) and CN-, and the majority of Zn, Cd, Cu, Ni and Ag complexes with low dissociation constants. It is potentially toxic to humans and animals. Recognising and in response to the gold mining industryÆs need for an on-line WAD cyanide measurement device, Mintek recently developed the WAD Cynoprobe. The WAD cyanide analysis technique is based on the use of a ligand exchange reagent that liberates WAD cyanide from metal-cyano complexes. The ligand exchange reaction is represented by the following chemical equation: Metal(CN)X + yLigand <-> Metal(Ligand)y + xCN- The plant filtrate is treated with a ligand exchange reagent, to liberate WAD cyanide, before measuring the free cyanide concentration via amperometry. The instrument proved to be accurate and reliable in the laboratory as well as under industrial gold plant conditions during various trials. It has gained wide-spread commercial acceptance both locally and internationally. However, itÆs recent exposure to complex ore types have called for refinements to the analysis technique. It has been further developed to improve its precision and accuracy and to remove reagent and thiosulfate interferences. Its compatibility with the most commonly used destruction oxidants has also recently been investigated. The WAD Cynoprobe may be configured to measure both free and WAD cyanide concentration. Its fast analysis time, approximately 5 min, makes it suitable for use in the control and optimisation of the cyanide destruction and recovery process. Proper oxidant dosage control and monitoring of effluent concentration levels will ultimately result in less cyanide and post-destruction salts discharged into the environment.

Jan 1, 2008

By Carter A. C

The increasing need for alternative energy sources as well as the less clearly perceived but equally increasing demand for non-fuel minerals has resulted in extensive exploitation of near surface deposits. Many such deposits have depleted reserves and mining corporations are increasingly turning their attention to deposits, with thicker overburden, less competent materials, steeper dips and more complex structure. These deposits pose mine layout, geotechnical and equipment problems as well as the need for large outputs to achieve economies of scale. The paper describes the major problems and operational solutions for such deposits using continuous excavation and transport equipment.

Jan 1, 1980

This report will differ slightly from the traditional scientific and technical discussions given at this type of conference. It will focus on the personal experiences and choices that I undertook when deciding on my graduate position and location after completing university studies. Throughout the duration of my course I had experience in both fly-in, fly-out operations in the Pilbara and residential operations in the West Australian Goldfields. These experiences, though limited, allowed me to explore the two different methods and their pros and cons, and consequently to make my choice for graduate employment. Throughout the duration of my degree I believed it was important to gain a basic understanding of the two methods, focusing on lifestyle and personal interactions. The decision that a residential site suited my personality and lifestyle then allowed me to refine my job applications to a more specific list of mine sites and companies, resulting in a residential position with BHP Billiton at their Iron Ore operations in the Pilbara, Western Australia.

Jan 1, 2005

The Mammoth Mine is located some five kilometres from the town of Gunpowder which is approximately 120 km north-west of Mount Isa in Queensland.

Jan 1, 1993