Search Documents

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By E Forbes, G V. Franks

"This study investigates the dual function of a temperature responsive anionic co-polymer of poly (N-isopropyl acrylamide) (PNIPAM) as a selective flocculant/flotation collector. PNIPAM is used for separating hematite from 50:50 mixtures of hematite and quartz, at a variety of particle sizes. The performance of PNIPAM in this system is compared to that of conventional flotation collectors: sodium oleate and sodium dodecyl sulfate. The results of the study demonstrate that anionic PNIPAM used at 50¦C (above the lower critical solution temperature (LCST)) is the most effective flotation collector for hematite particles in the size range between 10 and 20 ¦m. This is attributed to the increased probability of both particle/bubble collision and particle/bubble attachment through the formation of hydrophobic hematite aggregates. Anionic PNIPAM used at 50¦C also produced the highest hematite recoveries for very fine hematite particles (circa 1 ¦m). However this recovery was completely unselective. This lack of selectivity is partially attributed to the activation of quartz particles by PNIPAM, but is thought to mainly occur as a result of entrapment of quartz particles within the matrix of hematite aggregates.CITATION:Forbes, E and Franks, G V, 2013. Selective separation of hematite from quartz by flotation using a temperature responsive polymer, in Proceedings Iron Ore 2013, pp 381-390 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

The cloud transform simulation is a technique used to generate realisations of correlated attributes. The principle of this technique is to partition the scatter diagram between the input attributes into several interval classes and derive for each class a cumulative distribution function (CDF) using only the data pairs of the scatter diagram in that class. The simulation then proceeds like a traditional Monte Carlo simulation but using the derived CDF in each class.The cloud transform simulation has the advantage of being a simple and fast technique that is able to reproduce the uncertainty in the relationship between the two input attributes regardless of whether the relationship is linear or not. However, the technique has three major drawbacks. First, the number of classes has an impact on final simulated results and there is not a robust approach to define such number. Second, simulated results exhibit some saw tooth variations that are unrealistic and third the reproduction of the spatial continuity of the simulated attribute is not guaranteed.This paper presents the use of the quantile regression approach in order to overcome the first two disadvantages of the cloud transform simulation. Details of the technique and how it can be coupled with the cloud transform simulation are presented along with a real case study.

Sep 26, 2011

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By R McIlwraith, B Breul

"This paper discusses the successful use of bituminous geomembranes (BGMs) in mining applications since their development in 1974. It explains and illustrates the structure of a BGM composite, which is a geomembrane manufactured by impregnating a polyester geotextile with a compound of bitumen, elastomer and filler. Examples of applications of BGMs in the mining industry are also presented in the following contexts.Storage of solid waste: storage of mining waste at mines in Canada heap leach pads in France, Peru, Chile and Turkey at the base of a mining waste landfill in Brazil capping of solid mining waste in Chile and Canada temporary capping of mining stockpiles in Australia (with possible reuse of the BGM for other works).Examples of the application of BGMs for the storage of liquid waste in mining containment reservoirs in Canada, Guatemala and Peru will also be given.For each example given, reasons are supplied that supported the choice of BGMs by the clients and consultants, drawn from the following advantages of the BGM:BGMs have excellent puncture strength, due to the internal polyester reinforcement, as well as excellent ultraviolet resistance. This often eliminates the need for a cushion geotextile or cover soil over the BGM.BGMs have a very long life expectancy, in excess of 300 years, in subsoil conditions (Breul et al, 2004).BGMs can be installed in very harsh climatic conditions. They are suitable for high wind environments as their heavy mass per square metre makes them resistant to wind uplift. The low coefficient of thermal expansion means that BGMs are suitable for installation in mines where very low or very high temperatures are expected. This reduces construction delays and allows for a quicker use of the mining facility.The fact that the BGM can be installed by the mine’s own workforce, after appropriate training from the BGM manufacturer, allows for a more flexible construction sequence on the mine.Ability of the BGM to connect to other materials such as concrete, steel, rock and other geomembranes that may be on the mine site.The technical advantages of a BGM enabled the engineering consultants to prepare solutions for their mining clients that had a lower environmental risk, had a faster completion schedule and were overall a cheaper option than with a polymeric geomembrane.CITATION:Breul, B and McIlwraith, R, 2015. Bituminous geomembranes in mine construction, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Lee RJ

A significant basemetal province is recognised in the southern part of the Bonaparte Basin, Western Australia. Epigenetic stratabound carbonate hosted Pb-Ag-Zn mineral- isation occurs in dolomites of Tournasian age within a marginal marine transgressive carbonate and fine grained clastic sequence, spatially overlying the lagoonal facies of a Late Devonian reef complex. The deposits comprise coarse grained sulphide mineralisation characterised by high Pb:Zn ratios (10:1) and high silver (50 g/t) content. They occur at shallow depth, are flat to moderately dipping, and form a discontinuous mineralised trend at the margin of the Sorby Platform, which flanks a Precambrian basement high. Host rocks are predominantly sedimentary breccias and dolomitised footwall carbonates associated with a significant local unconformity transgressed by a siltstone cap rock sequence. The deposits are structurally related to synsedimentary growth faults, local basement highs and tensional en-echelon breccia systems. Fluid inclusion studies have concluded that mineralisation was deposited from a low temperature (85¦C-115¦C) saline ore forming solution. Lead isotope work reveals a Precambrian genetic source of the lead. Locally remnant textures after sulphates are recognised within the host sequence together with common bitumen and oil shows. Reduction of sulphate to H2S was possibly facilitated by either bacteria. activity, or by residual hydrocarbons which acted as a reducing agent. An alternative source of H2S may have been afforded by the thermal degradation of hydrocarbons. A 'mixing' genetic model is proposed for the mineralisation, which conceives the expulsion of metal enriched basinal brines followed by their precipitation as sulphides after mixing with locally derived reduced sulphur solutions at relatively shallow depths in their structural/stratigraphic sites of ore deposition.

Jan 1, 1986

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007

By G MORRIS

The mining industry has been rightly proud of its environmental achievements and it would be fair to say that in some areas the Australian mining industry is at the forefront of world practice in environmental management and mine rehabilitation. The `environment' has certainly been a growth area over the past three decades with growing awareness in the 1960s, some large battles and the of significant legislation in the 1970s. The most important period however has been the 1980s and so far the 1990s where, in addition to the of some more rigorous legislation, we have seen the practical application of environmental management/rehabilitation Techniques.

Jan 1, 1992

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J P. van Dijk, M Munro

Discrete vein modelling presents an innovative geology driven 3D modelling method for quantification of vein hosted mineral deposits, with far reaching potential for critical mineral supply and low impact resource extraction. By integrating key geological drivers with advanced discrete fracture network modelling, the DMX protocol (launched in 2019) converges to a more realistic representation of complex vein systems in three-dimensional space. The approach insights greater geologic reasoning in distributing mineral grades where vein boundaries are already defined. This presents a viable alternative to existing modelling and estimation methods and has important implications for mineral resource estimation and reporting. Further implications are discussed, where the enhanced understanding of complex orebody characteristics can potentially be used in optimising mining and mineral processing, supporting more sustainable and efficient mining practices.

Sep 1, 2024

By D C. Ford

The Argyle AK1 orebody was discovered in 1979 and subsequently found to be a large, economically viable reserve with high grade diamondiferous ore. Production began via an open pit operation at the end of 1985 and has continued for some 25 years to present day. This, however, will come to an end in the next few years with production moving to an underground operation via block-cave mining methods.A series of studies from 2001 - 2005 was carried out; diamond drilling commenced after approval in 2006, from an exploration drive to determine the likelihood of the current proposed block cave operation.In 2006, development of the block cave project began, in order to realise the part of the orebody below the extent of the open pit mining operation.Development of the block cave technique, comprising an undercut level beneath the target zone of the orebody with subsequent extraction level 15 - 20 m beneath, relies largely on a number of block-caving parameters (hydraulic radius, rock type, structure and orientation of stress and grade of the orebody). These all have an influence on cave ability and eventual profit of the operation. Evaluation of further potential for taking this orebody beyond the block cave phase with options such as sublevel-caving are being considered for the UG-2 portion of the resource/reserve. Diamond drilling for this work is currently under revise.The challenges faced in transitioning form the surface operations to the underground, comprising a changing workforce, converging development drives, underground aquifers, major excavations and transportation of ore via automation are intriguing.

Aug 22, 2011

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

Natural gas from the south west Queensland gas fields is now available in north west Queensland to fuel the development of many Carpentaria Mineral Province projects. Like these projects, the south west Queensland gas project, developed under the operatorship of Santos Ltd, has its own æMining CycleÆ. While the project is entering its third expansion phase, it is at the same time actively extending its discovery phase, with large programs of gas exploration and reserves definition. This paper outlines the history of the south west Queensland gas project, with particular emphasis on the relationship of the project to north west Queensland.

Jan 1, 1998

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

By W J. Rankin

Metals are well suited to sustainable development goals. They are not biodegradable and have virtually an unlimited lifespan and the potential for unlimited recyclability. Thus metals can be considered as renewable materials. However mineral resources, the source of primary metals, are ænon-renewableÆ as their supply is finite, but this does not necessarily mean scarcity. In this paper the results from a series of Life Cycle Assessments of primary metal production processes for copper, nickel, lead, zinc, aluminium and steel have been used to examine how metals may contribute to societyÆs transition to sustainable development. Particular issues considered include:current metal reserves and how these may change in the future; some of the environmental impacts (Total Energy, Global Warming Potential and Acidification Potential) associated with primary metal production and how they will be exacerbated by declining ore grades; new processing technologies with lower energy consumptions and improved metal extraction efficiencies that will reduce reserve depletion and environmental impacts; increasing the utilisation of æmetals in useÆ by recycling, with particular reference to aluminium; and the potential impact of a carbon tax on metal prices and how this may influence the ways in which metals are used in the future.

Jan 1, 2002

By S G. Li

Mine intelligent ventilation is an important guarantee to realise intelligent mining. It is the integration of the Internet of Things, big data, artificial intelligence, internet, cloud computing with ventilation technology, forming a complete ventilation system with intelligent perception, intelligent decisionmaking, intelligent emergency response and airflow control. In order to fully grasp the progress and trends of mine intelligent ventilation research in western China. The paper based on literature analysis and field application research, comprehensively expounds the main research and practical results of mine intelligent ventilation in western China, mainly analyses the development status of key technologies such as accurate and rapid determination of mine ventilation parameters, intelligent analysis and decision-making of ventilation and intelligent regulation of ventilation equipment, and introduces the field test or application of mine intelligent ventilation technology in western China. It lays the foundation reference for related research and improving the intelligent level of mine ventilation.

Oct 12, 2022

By A Keogh, P Allen, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Private equity (PE) firms are comparatively free of mandatory requirements for the level and scope of due diligence applied prior to making investment decisions in minerals projects when compared to listed entities, sovereign funds or financial institutions adopting the Equator Principles (Equator Principles Association, 2013). While this freedom allows for flexibility, agility and innovation in making investment decisions, it can also expose PE firms to material risks that may impact their ability to successfully list the projects or attract later financing.Financial institutions and investors with mandatory due diligence and disclosure standards may refrain from investment in or acquisition of a project if it fails to meet various performance requirements. There are many high-profile projects that have suffered significant write-downs on book value after acquisition because specific non-mining issues were not adequately assessed. Thus, a PE firm may be left with an asset that is difficult to divest and incapable of securing development finance.PE firms can manage this risk by being aware of the growth trend in the adoption of ‘international standards’ in addition to host nation standards and legislative requirements. This paper outlines key issues for PE firms to address to maximise the chances of obtaining funding or successfully taking an exploration or mining project through to listing or divestment. Two steps are required: identification of gaps in performance and priority matters of interest to financial institutions and development of action plans to ensure that the priority requirements are met or capable of being met.A PE firm can set its project for success by understanding the social and environmental performance requirements of international standard financiers and by setting the project on the right path to meeting these requirements, and thus making it an attractive investment.CITATION:Allen, P, Stoker, P and Keogh, A, 2015. Setting for success – private equity exploration and mining project buy-in to listing and divestment , in Proceedings PACRIM 2015 Congress, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S Russell

The completion of the $1.1 B Cape Lambert Upgrade project is the second ‘pillar’ in Rio Tinto Iron Ore’s expansion program that has enabled Rio Tinto Iron Ore to effectively double iron ore shipping capacity from the Pilbara between 2003 and 2009 to 220 million tonnes per annum (Mt/a), following the successful completion of the Dampier Port upgrade project two years earlier.The Cape Lambert Upgrade has built on and enhanced many of the engineering achievements of the Dampier Port upgrade project, as well as developing innovative and unique engineering solutions for this complex ‘brownfields’ project that presented its own challenges, particularly in this distinctive open-water port environment.The project was implemented in two phases to achieve an increase in port shipping capacity from 55 to 80 Mt/a – an enhancement phase and an expansion phase.The initial enhancement phase, which provided an increase to shipping capacity from 55 to 60 Mt/a, focused on increasing the utilisation and effi ciency of existing plant and equipment with a relatively small capital expenditure.The expansion phase, which provided the increase in shipping capacity to 80 Mt/a, included extending the existing iron ore wharf by 256 m to create four shipping berths, a new shiploader, an expanded stockyard (including a new fourth bucket wheel reclaimer) and a new surge bin facility to maximise outloading tonnage rates.The Cape Lambert Upgrade project was implemented whilst the port remained fully operational and continued to ship record tonnages of iron ore throughout the project duration. This achievement required signifi cant upfront planning and sequencing of construction activities to support the operation of the port. Innovative design and construction techniques were used to mitigate the impact and enable construction activities in and around the operating plant.Throughout the project, new benchmarks in engineering design and construction practices were established, which have since been adopted for new iron ore port facilities currently in planning phases.

Jul 11, 2011

By H Sofatzis, J Kinal, J Siliezar, B Kirkwood

Ernest Henry Mining (EHM) is a copper, gold and magnetite mining and processing operation located 38 kilometres north east of Cloncurry in the Mount Isa - Cloncurry mineral district of north west Queensland, Australia. The EHM ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite.At the end of 2009, after a series of promising laboratory test work, EHM converted the ball mill media charge from forged steel to high chrome media. Laboratory test work also indicated that with the use of high chrome media, the pH was able to be reduced with no negative impact on plant performance. At high pH values (above 10.5), the forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response.This paper provides an overview of the effects of reducing the pH in the EHM copper rougher flotation circuit. The pH in the roughers was dropped from 10.6 to 9.6 to determine the impact on the rougher performance and the subsequent performance of the whole copper flotation circuit. It was found that there was a slightly increased improvement in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold.With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.CITATION:Kirkwood, B, Kinal, J, Siliezar, J and Sofatzis, H, 2013. Low pH trial in the Ernest Henry Mining copper rougher flotation circuit, in Proceedings MetPlant 2013 , pp 371-377 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013