Search Documents

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By F Hungerford, T Ren

"Gas management has always been a major concern for the ventilation officer of any gassy mine. With an increase of mining depth and gas content, there is a great demand for the development of in-seam drilling sites where boreholes can be drilled for the pre-drainage of gas prior to longwall operation. The ventilation and gas management in the drilling site therefore becomes a critical component of mine safety. In this study, advanced computational fluid dynamics technology was adopted to investigate the aerodynamics of gas emitting from the drilling site and boreholes during normal drilling and, in the case of a sudden gas inrush, from the borehole. In addition, the impact of different ventilation controls on gas removal in the drilling site was investigated. Modelling results indicate that gas accumulation zones could be formed if the ventilation system fails to deliver sufficient airflow to the drill site, especially when a sudden gas inrush from a borehole occurs. The configurations of brattice, layout of ventilation tubes and the gas emission rate all have a significant effect on the gas distribution. Due to variations in site-specific conditions, it would be desirable to conduct modelling studies to assess the effects and efficiencies of a ventilation design for the varying environment on-site before carrying out drilling practice. CITATION: Ren, T, Hungerford, F and Wang, Z, 2015. Computational modelling studies of ventilation management for underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference, pp 239–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

The Australian coal industry has undergone sevenfold growth over the last 30 years and since 1985 has been the world's largest coal exporter. Three quarters of Australia's coal production is exported so its future is dependent on it remaining internationally competitive with other energy sources and other coal exporting countries. Coal is likely to increase its share of the energy market during the nine- ties as oil prices increase, new coal-fired capacity is commissioned and some form of nuclear energy is developed which is of acceptable safety standards to the community for use in the 21st century. Gas may take a part of coal's anticipated market share by the Year 2000. While coal exports will increase from China, Colombia, Indonesia and Venezuela and satisfy some of this additional coal demand Australia will also expand its export production, due to its existing advantages. The United States, Canada, South Africa, Poland and USSR seem unlikely to enjoy the same degrees of expansion and some, particularly Poland and USSR, will decline. Australia will always find it difficult to compete in the more distant markets due to levels of ocean freight, although its high quality coals will tend to partly offset such disadvantage.

Jan 1, 1988

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

The operators of the iron ore railroads in the Pilbara faced problems of excessive wear between rail and wheels as the tonnage hauled increased in the early 1970's. Joint research projects were begun between Hamersley Iron, Mt Newman Mining and the BHP Melbourne Research Laboratories to study these problems and recommend solutions. The particular problems of wheel rail interaction were solved by asymmetrical profile grinding of the rail and modifications to the machining of the wheels. Rail materials were improved through increasing yield strengths by alloying and by heat treatment. Wheel materials were improved by alloying. The economic benefits of these improvements have been demonstrated by much reduced re-rail requirements and other reduced maintenance costs.

Jan 1, 1986

By A H. Clemens, T A. Moore

This paper discusses a number of technical issues related to marketing coal. It outlines how the results of research undertaken in New Zealand and overseas can help producers address a range of technical factors that impact on production costs and marketability. The paper also discusses trends in coal utilisation for power generation and how new technologies may require coal with different characteristics. Research and development into options for CO2 sequestration are discussed including carbon storage in forests, and removal of CO2 from flue or fuel gas in power stations, and its disposal.

Jan 1, 1997

By Oboso A, Nakahiro Y, Takenaka Y, Wakamatsu T

As part of the fundamental studies on the recovery of Au by solvent extraction, the synergism of combined extractants on the extraction of An from the sulphuric acid solution containing thiourea was investigated. Extractants tested were di-(2-ethylhexyl)phosphoric acid (D2EHPA), tri-n-octylamine (TOA), tri-n-butyl phosphate (TBP), and trioctyl phosphine oxide (TOPO). Four kinds of extractant combinations, D2EHPA/TBP, D2EHPA/TOPO, TOA/I'BP, and TOAITOPO, were tested to clarify the synergism on the extraction of Au in terms of various concentration ratios, diluents, the concentration of sulphuric acid, and the concentration of thiourea.

Jan 1, 1993

This paper describes a case history of using an integrated geochemical and hydrogeological approach to predicting solute transport from gold mine tailings in highly fractured volcanic terrain. Two modes of transport are identified, namely discrete fissure flow and diffuse seepage through the intervening weathered rock. A simple mass balance approach is used to predict concentrations at points of emergence because most of the seepage migration will be by way of the discrete fissures where advective transport will predominate. The mass balance method has been modified to allow for natural degradation of weak acid dissociable cyanide. The long term effects of diffuse seepage are also examined.

Jan 1, 1988

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity. Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer. Having concluded that steaming coal in particular is likely to become even more important as a generator of base load electricity, the paper looks at the opportunities this presents for exporters such as Australia, and touches on some factors that could prevent development of those opportunities. This paper will concentrate on electrical energy. For the purposes of this paper, the Pacific Basin refers essentially to Australia, New Zealand and the Asian countries bordering the Western Pacific. As a supplier, Siberia is not included because, although it has great potential, it is thought that problems of climate, infrastructure and political restructuring will delay the realisation of that potential until the next century. Although it deals with the Pacific Basin region, where many countries are industrialising rapidly from a predominantly agricultural base, it looks at the experience of mature industrial DECD economies where their experiences seem relevant.

Jan 1, 1990

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

Platinum-group minerals (PGM) are recorded from a number of localities along theWaiau River, western Southland, and the south coast of the South Island, New Zealand. At each locality, small amounts of PGMs were recovered as by-products of historical gold mining operations. During the period 1890-1950 an estimated 1000-2000 oz. of æplatinumÆ were recovered from the region, the only area within New Zealand where PGM have been commercially exploited. The PGM suite of southern New Zealand consists of Pt-Fe alloys, IPGE (iridium subgroup, platinum-group elements) alloys, sperrylite (PtAs2), cooperite (PtS) and braggite ((Pt,Pd)S). The composition of Pt-Fe alloy exhibits considerable variation and two compositional populations are recognised. Some Pt-Fe alloy grains are chemically zoned. Iridium is the most abundant IPGE alloy phase and often contains considerable Pt, in contrast to osmium and ruthenium alloys. Cooperite and braggite grains are characterised by extremely low concentrations of Ni.   Exsolution of osmium and iridium from Pt-Fe alloy and Pt-Fe alloy from iridium is observed Several PGM host mineral inclusions which vary from single to poly-phase, display rounded to equant outlines and range in diameter from greater than 100 ¦m to less than 5 ¦m. Olivine and Ni-sulphide inclusions are only present within IPGE alloys. Pt-Fe alloy, cooperite, braggite and sperrylite host Cu-Fe sulphides, a wide variety of PGM, clinopyroxene, amphibole, magnetite and plagioclase within inclusions. Sperrylite also hosts Pd bismuthiotellurides, gold and several potassium-rich silicate phases. Similarities in inclusion phases and mineral chemistry from several localities suggest that the PGM are derived from a single (as yet unidentified), probably calc-alkaline magmatic source. This source is situated somewhere along the margins of the western Southland sedimentary basin where PGM liberated by erosion are transported down the Waiau River and dispersed eastwards along the coast by strong longshore currents.

Jan 1, 1995

By K L. Brown

The concentrations of trace metals in deep hydrothermal solutions (~1 km depth, 200 to >300¦C) from modern hydrothermal systems in the Taupo Volcanic Zone, New Zealand, and Ladolam, Lihir Island, Papua New Guinea were obtained using a purpose-built downhole fluid sampler and ICP-MS analyses. The results range widely: gold (<0.1 - 23 ppb); silver (<3 - 2400 ppb); arsenic (100 - 18 000 ppm); antimony (2 - 1200 ppm); mercury (<1 - 78 ppb) and provide the basis for quantifying the flux and fate of metals as well as assessing their sources (Simmons and Brown, 2006, 2007). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By R Dunne, D Yan

In flotation where a bulk flotation concentrate is produced or a gangue sulfide such as pyrite contaminates a concentrate, residual collector has to be removed from the sulfide surfaces to allow selective separation in a subsequent flotation step. Depending on the sulfide mineral, the main species that needs to be removed when using a xanthate collector is either a metal xanthate or dixanthogen. For the identification of surface species, specific solvents may be used to remove each species û metal xanthates are known to be soluble in acetone whilst dixanthogens are known to be soluble in non-polar solvents such as diethyl ether. Xanthates break down with time, temperature and pH into various decomposition products. The major decomposition product is dixanthogen which can aid flotation but other products such as perxanthate and carbon disulfide can have an adverse effect on flotation. Various analytical techniques can be employed to monitor the formation of decomposition products on the surface of the mineral and in solution. The best of these is ultraviolet spectroscopy as it has diagnostic peaks for decomposition product determination. In this work two approaches were taken to understand the relationship between the flotation of a chalcopyrite and pyrite from an ore containing these two minerals. One approach was to remove the xanthate species with an organic solvent and then use ultraviolet spectroscopy to determine the concentration of dissolved species. The second method involved measuring xanthate decomposition in solution by measuring the residual xanthate concentration using ultraviolet spectroscopy. These experiments confirmed the species adsorb at the surface of the mineral and how these species affect the recovery and grade of the valuable mineral. In both cases pH and temperature were varied and two xanthate collectors (SEX and PAX) were used to study these relationships. These relationships could be applied to industrial flotation systems and allow for more accurate determination of optimal xanthate dosage and hence save on reagent costs.

Jan 1, 2005

By J van Niekerk

The BIOX« process for the treatment of refractory gold ores and concentrates has been commercially in operation for 18 years. A total of six BIOX« operations have been successfully commissioned since the commercialisation of the process. Four of these BIOX« plants are still in operation today. There has been a renewed interest in the process the past few years with two BIOX« plants, the Suzdal plant in Kazakhstan and the Fosterville plant in Australia, scheduled for commissioning during 2004. Four new projects are also in various stages of development and are currently scheduled to be commissioned during 2005 and 2006. Research into the process are currently focussed on the two highest operating cost items for the commercial operations, namely power for agitation and air dispersion and cyanide consumption during leaching. Laboratory aeration and agitation testwork using the A340 up-pumping agitation system has shown that similar mass transfer rates can be achieved at slightly higher agitator power. The up-pumping system, however, eliminates the need for a separate blower and sparger system as air is introduced into the slurry from the slurry surface. The use of the thermophile bacteria as the final oxidation step during biooxidation has shown great promise. Reductions in cyanide consumption of up to 50 per cent were achieved when using the combination mesophile and thermophile process compared to standard BIOX« product solids. The combined process takes advantage of the milder oxidising conditions of the well known BIOX« process for the bulk of the oxidation and then uses the high temperature thermophile bacteria to complete the oxidation. The ASTERÖ process for the biological degradation of cyanide and thiocyanate containing effluent solutions has been proven to be efficient and stable. The process uses an activated sludge system with a residence time of approximately six hours in the sludge reactor. Heavy metals and metal cyanide species have also been shown to be removed successfully from solution.

Jan 1, 2004

For Australian mining projects, sustainable groundwater use is typically defined as a groundwater extraction regime, measured over a specified planning time frame, which allows acceptable levels of stress and protects dependent economic, social and environmental values (DEH, 2004). This principle is compatible with most stakeholdersÆ understanding of our national environmental objectives, yet the application of this policy on a project-specific scale is not always straightforward. Three examples of sustainability issues in the management of groundwater in mining are presented. These examples highlight each of the three dependent values: environmental, economic and social.

Jan 1, 2006

The problems arising in the excavation of hard rocks with the use of mechanical tools consist chiefly in a slow advance rate accompanied by an intensive wear due to the toughness and abrasiveness of the rock. In order to allow the further extension of mechanical excavation beyond the limits of the presently available technology, the assistance of waterjet aiming at improving the performance of the equipment while reducing the wear rate of the tools, has been recognised as one of the most interesting technical solutions. The paper illustrates the improvement of the performance of both disk cutters and picks obtained with the waterjet assistance at the Waterjet Laboratory of the University of Cagliari on a medium-hard rock.

Dec 6, 2010

By the use of flotation tests it was confirmed that there are two functions of oxygen in sulphide mineral flotation. Sized samples of galena and chalcopyrite were sulphidized, washed free of excess sulphide ion, and then contacted with air-saturated water for certain lengths of time. The mineral was then transferred to a sealed laboratory flotation cell containing water with a known concentration of dissolved oxygen. Xanthate and frother were added and flotation continued for 1 min.Both the extent of mineral oxidation and the concentration of dissolved oxygen markedly affected the flotation of galena and chalcopyrite. The response to a change in either variable is dependent on the level of the other, but generally best flotation occurs with the maximum degree of air saturation of the pulp. Galena flotation is hindered by oxidation of the mineral beyond a small threshold amount but a similar effect for chalcopyrite was not observed...

Jan 1, 1967