Search Documents

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

Metsim is proving to be a powerful tool when designing a heap leach operation. The most useful outputs arc determining the fluctuations in pregnant solution recovery rate, make-up water rate, gold recovery rate. and pond levels. Detailed data are needed for input: a pad loading schedule, a mining rate schedule for each ore type, column leach test data for each ore type, column tests on water dynamics (ie hourly flow-out versus-in during saturation and drain-down), monthly rainfall and evaporation data, and proposed pond dimensions. These data allow 'what if' studies on application rates, leach rates, loading rates and other variables of interest. Examples will he given of modelling both a rectangular pad and a valley fill operation.

Jan 1, 1994

By D Weatherley, T Baumgartl, L Huang, Q Shao

The stabilities of rehabilitated landforms are often threatened by the altered surface hydrology, especially the excessive surface run-off, which may cause severe water erosion and associated pollutant transport to surrounding areas. These effects would lead to pollution in waterways and render the failure of newly established vegetation. An accurate quantitative evaluation of run-off problems are consequently essential for the proper rehabilitation designs which can help minimise these harmful consequences. For this purpose, in this study a novel run-off model, RunCA, was developed based on Cellular Automata (CA), integrating fundamental hydraulic principles. In this model, a series of rectangular cells were employed to cover the study area. Run-off production within each cell was simulated by determining the cell state (water surface elevation) that consists of both cell altitude and water depth. The distribution of water flow among cells was determined by applying CA transition rules based on the improved minimisation-of-difference algorithm and the calculated flow travelling time. RunCA was applied to various aspects in mined land rehabilitation planning, including landform designs for both hill-slopes and tailings dams, revegetation strategies and cover constructions. Simulation results showed that surface run-off increased with slope gradient and more run-off was produced on convex and straight slopes than on concave and S-shape slopes. Both mounds and rip lines constructed on the tailings dam surface could help reduce the water discharge. Vegetation planted in rows were more effective than those in columns or patches in controlling run-off. Increased cover thickness had the potential in reducing run-off rates, and the covers with an increasing thickness from top to bottom of the slope tended to be more efficient than those with a constant thickness. All these results have demonstrated the efficacy of RunCA as a simulation tool in assessing the hydrologic behaviours of different rehabilitation designs. Compared to the traditional hydrologic models, most of which were developed for the catchment scale studies, RunCA has the potential advantages in capturing the dynamic and spatially varied run-off behaviours at different spatial and temporal scales.CITATION:Shao, Q,?Baumgartl, T, Huang, L and Weatherley, D, 2014. A cellular automata-based run-off model and its application in mined land rehabilitation designs, in Proceedings Life-of-Mine 2014 , pp 81–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M D. Melville, B C. T Macdonald, T D. W

The surface waters in regions with acid sulfate soils (ASS) can contain high concentrations of acidity and dissolved metals. These soils cause problems for agriculture, construction and development. The water can be neutralised through many techniques, however a technique that is low in maintenance and low in cost is most desirable. Due to the vast spread of ASS along AustraliaÆs coastline an expensive and high maintenance solution would not be cost-effective. In this study, a passive treatment system that has been used to neutralise acid rock drainage has been applied to treat ASS water. This system is commonly referred to as an oxic limestone drain (OLD) or an anoxic limestone drain (ALD) depending on the waters dissolved oxygen concentration. The system that has been developed for ASS has a similar closed system to the OLD or ALD, that traps the carbon dioxide which forms when limestone reacts with acidic water. It has been called a closed tank reactor (CTR) and is constructed by placing limestone into an airtight tank. A common problem that will occur when acidic water with a high concentration of dissolved metals reacts with limestone is the formation of metal oxy-hydroxide precipitates. These precipitates can coat or armour the limestone and reduce its reactivity. To minimise the accumulation of precipitates in the CTR, perforated subdrains have been installed. It is anticipated that high water pressure and flow through the subdrains will remove some precipitates. A sump has also been installed at the base of the tank to collect precipitates that settle under gravity. The CTR has been tested for 70 days at a sugar cane farm located at McLeods Creek, NSW. Within this time the sump and subdrains have been used to flush the system. An orange solution was produced during flushing and it is believed to contain iron and aluminium precipitates. The initial performance of the CTR raised pH by at least one unit. Almost all dissolved aluminium was removed and more than half the dissolved iron. The total titratable acidity ranged from 17 - 92 mg/L CaCO3 in the initial month of monitoring. After passing through the CTR the acidity was reduced to zero. The performance of the CTR during the last few days of monitoring decreased. This is believed to be due to a pulse of water with higher acidity and dissolved metal content that lasted a week. In this pulse, the acidity reached 307 mg/L CaCO3 and the total dissolved aluminium reached a maximum of 24 mg/L. Higher concentrations of dissolved metals may have been the cause for lower performance due to increased precipitation and coating on the limestone.

Jan 1, 2003

By C C. Souza, S C. Amarante, A C. Arauj

All major companies now producing iron ore in Brazil currently employ or are planning to employ some sort of concentration method to upgrade their fine sized products (sinter feed fines and pellet feed fines). The criteria for the selection of the most suitable concentration method for each application include a series of parameters; the most important among them being related to ore mineralogy. This paper reviews the concentration operations currently employed in Brazil and shows how ore mineralogy plays a fundamental role in the selection of a given method. Examples involving gravity concentration (jigs and spirals), magnetic separation (Rare Earth wet drums, ferrous wheel, and Jones type magnetic separators) and flotation (especially column flotation) are discussed. Fundamentally important for the selection of a concentration method is the mineralogy of iron-bearing minerals and gangue minerals presented to the feed to the concentration unit operation. For instance, the presence of liberated quartz as the major gangue mineral for a pellet feed size stream generally indicates that flotation will be the best selection for the concentration of that stream. However, even if magnetite is present only in the form of crystal relicts within hematite grains, it may lead to the selection of either magnetic separation alone or a combination of magnetic separation and flotation for concentrating such material. Presence of gibbsite and/or kaolinite as the major phase containing alumina will also affect the selection of the concentration method in all cases. Again for the case of pellet feed size streams, kaolinite does not interfere with flotation whereas gibbsite tends to contaminate flotation concentrate (pellet feed fines) as it is depressed together with iron oxides and hydroxides during the reverse cationic flotation process.

Jan 1, 2002

By R E. Gerald II, B Zhang, T Sander, J D. Smith, J Huang, R J. O’Malley, H Tekle

In the steelmaking process, mold fluxes are essential for ensuring thermal insulation, refining, and the efficiency of continuous casting. Real-time understanding of the in-service composition of slags and fluxes are crucial for optimising the steel production process and improving the quality of the final product. An in situ fibre-optic Raman probe that enables the study of the structure, composition, and viscosity of molten slags and fluxes at steelmaking temperatures has been developed and demonstrated both in the lab and in foundry scale experiments. The focus of this study is on the structural, compositional, and property analysis of molten fluxes in a laboratory setting, with the aim of applying this technology for in situ monitoring during industrial production. Raman spectra were successfully collected at various temperatures from 1000°C to 1400°C in real-time and analysed using a deconvolution algorithm to isolate and quantify peaks in the spectra associated with the specific structures of molecular components in molten and solidifying flux. The research successfully combines in situ Raman spectroscopy with high-temperature viscosity data, specifically targeting CaO-CaF-SiO2-Al2O3 based mould flux systems. Specified ratios of the deconvoluted Raman peaks, such as Al-O-Al/Si-O-Si ratio, shows good correlation with the flux chemistry, while the Q3/Q0 peak ratio shows good correlation with viscosity. A ruggedised Raman probe system was also developed and demonstrated in an 80 kg induction furnace. Ultimately, the goal of this work is to demonstrate in situ slag and mould flux analysis in industrial processes, such as in the continuous caster or electric arc furnace (EAF).

Aug 21, 2024

The arbitration process, and its drawbacks: Any time you have taken part in a major arbitration, and the decision, when it comes out, is not what you thought it would be (which is bound to happen occasionally), the normal reaction is something like æthe arbitrator got it wrongÆ. Again normally, when you have cooled down a bit, and you look in more detail at the decision, you can see, probably, æwhere he got it wrongÆ (it is only male arbitrators who get it wrong). Ultimately, when reason prevails, and you reflect on it, you can see that what really happened was that you failed to get the arbitrator to see what you were getting at in the point or points concerned. This is doubly frustrating, when you consider what has been involved in getting to this point, having been through it all at least twice. An alternative to this process may be the dispute review board.

Jan 1, 1999

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

It is not often that mines have as much warning of the approach of bad ground conditions as was the case at the Western Mining Corporation, Kambalda Nickel Operations Lafranchi/Schmitz Decline. Most aspects of this operation are in fact quite unique and like the best solutions, the answer to the problem of weak and foliated ground conditions was relatively simple; requiring the use of readily available explosives although the idea of using it in this manner may not be the most obvious.The use of high shock energy POWERGEL 2131 cartridges proved to be the correct answer, in conjunction with small changes in drill pattern design. The resulting lack of overbreak bears testimony to the success of the concept and the commitment of the miners to achieving a safe working environment.

Jan 1, 1992

By Y Zhu, D J. Williams, M O’Neill, C Zhang, X Lei

A cover of inert material overlain by topsoil is required over compacted, seawater-neutralised red mud, a waste product from the refining of bauxite to produce alumina. The cover is to be revegetated, and it is necessary to demonstrate that the potential evapotranspirative-driven uptake of salts from the seawater-neutralised red mud will not impact the revegetation. An instrumented column was designed and constructed to test the evaporation-driven uptake of salts from compacted red mud into an overlying cover material with a thickness limited to 600 mm. The PVC column is 1.2 m high, with a 200 mm internal diameter. The column is instrumented with up to ten of each of moisture, suction, salinity and temperature sensors, together with a data logger, designed and manufactured at The University of Queensland (UQ) in Brisbane, Australia. The sensors were installed through the wall of the column at various depth intervals, with each set of sensors located at quarter points around the circumference of the column. Two pressure transducers were installed in the column to monitor the change of water level due to rainfall and evaporation. The column was filled with compacted red mud to a depth of 600 mm overlain by 600 mm of cover material, both sourced from the Queensland Alumina Limited (QAL) site in Gladstone, Queensland, Australia. The column is installed on a building roof at UQ, alongside a weather station, and will be subjected to the prevailing weather conditions for up to 1 year in the first instance, during which time the weather conditions and sensor responses will be continuously monitored. This paper reports on the instrumented column set-up and the early results obtained from the test.CITATION:Zhang, C, Williams, D J, Lei, X, Zhu, Y and O’Neill, M, 2018. Instrumented column testing of salt uptake from compacted red mud into a cover, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 220–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By L Neindorf

The development and application of paste fill, cement slurry aggregate fill and shotcrete bulkheads at Mount Isa Mines is described. The progressive changes in filling style in the Mount Isa copper mines from a dry fill based cemented rock fill to tailings based paste fill and slurry fills is explained. The development of shotcrete arched bulkheads and engineered drainage system is described. Details on how Mount Isa Mines has achieved approximately 30 per cent cost reduction in backfill operations through innovations are given. The development of a rocky paste fill is explained.

Jan 1, 2005

By P Moser, P Schimek, F Ouchterlony

This paper summarises the findings of 27 model-scale bench blasts in magnetic mortar, which were conducted from 2011 to 2014 at the blasting site of the Montanuniversitaet Leoben.The aim of the study was the investigation of the influence of blasthole delay times in small-scale bench blasts on the face characteristics and cracking damage created in the surrounding rock, which affects the fragmentation in subsequent rows.The test specimens or blocks, which were produced out of magnetite concrete, were roughly 1:100 in scale to normal bench blasts. The confinement of the testing blocks at the sides and back ensured the similarity to normal bench blasts with regard to the wave transmission into the surrounding rock. The specimen contained three or four rows with five blastholes each and were shot row by row, with virgin (undamaged) material in row 1 and increasingly damaged or preconditioned material in the following rows.The tested delay times varied between 0, 28, 73 and 140 µs, which corresponds to 0, 0.4, 1.0 and 2.0 ms/m of burden.The evaluation of the material properties showed that the use of magnetite concrete eliminated the inhomogeneous behaviour of rock, but some unexpected differences of the individual production cycles were still detected.The characteristics of the bench after each blast was evaluated along three horizontal lines out of a 3D model of the bench face. The tested delay time sequences of the virgin (first row) and single preconditioned blasts (second row) produced more overbreak for longer delays, while the third-row shots resulted in a smoothened surface independent of the chosen delay.The introduced damage after every blast was evaluated by an observation of irregularities on the newly blasted bench face. The visible cracks at the top of the testing blocks were documented and divided into several crack families according to their angle, length and origin. The remaining block was broken out of the blasting site after blasting, cut into several horizontal and vertical slices and dye penetrant spray was used to visualise the cracks created. Some of the detected crack families showed an influence of the delay time. The calculated mean crack density and mean crack intersection density showed that longer delays resulted in a higher degree of damage.The fragmentation results were well reproduced by the basic three-parameter Swebrec function. The observed improvement of fragmentation in the second- and third-row blasts was linked to the preconditioning of the burden for the following row while blasting the actual row. With the exception of the simultaneously initiated blastholes, the blasts showed coarser fragmentation for the shortest delays, while the longest delays generated the finest fragmentation.CITATION:Schimek, P, Ouchterlony, F and Moser, P, 2015. Influence of blasthole delay times on fragmentation as well as characteristics of and blast damage behind a remaining bench face through model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C D. Rose

"The primary objective of this paper is to demonstrate a different approach to predicting and verifying mechanical sampling system precision. Early in the year 2011 an experiment was conducted to evaluate the sampling precision being obtained by a three-stage falling-stream mechanical sampling system for coal owned and operated by Peabody Energy. This system collects samples from lots averaging approximately 14000 t being loaded onto rail cars at a flow rate averaging about 9000 t/h. In phase 1 of the experiment, a total of 60 increments were collected in a two day period at preassigned intervals using a cross-belt sampler located on a conveyor belt feeding a silo upstream of the sampling system under evaluation. Coal variability parameters were calculated from the resulting laboratory analysis data using the gauge-invariant fractal model developed by the author.Estimates of precision of the three-stage system as a function of the number of increments were calculated using the variability parameters determined in phase 1. In phase 2 of the experiment, duplicate samples of 30 lots of coal were taken by the three-stage sampling system, enabling calculations of the precision being achieved by the system. Phase 2 precision estimates are in reasonable agreement with those of phase 1. Conclusions drawn from the experiment include the following: Experimental variograms or the equivalent correlograms are essential in understanding sampling issues and for designing a sampling system to meet specific precision requirements. Consensus coal sampling standards provided by ISO and ASTM may be improved by treating all stages of a mechanical sampling system as æsamplingÆ rather than considering downstream sampling stages as æsample preparationÆ, to be treated in a separate part of the document. The coal industry would profit from use of methodology for routinely monitoring the overall measurement precision and the precision of the individual components of measurement: sampling, sample preparation and laboratory testing. This would not only give necessary credence to the measurement results but would also no doubt, lead to more efficient sampling system designs.CITATION:Rose, C D, 2012. Evaluation of precision being obtained by a three-stage sampling system for coal, in Proceedings Sampling 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By J, T C. McCuaig, J Hodgkison, T Fouet

Olympic Dam is the eighth largest Cu deposit and the largest U deposit in the world, with approximately 35 million tonnes of contained Cu and 1.2 million tonnes of U. The most recent resource estimate was for 2.95 billion tonnes of mineralised material with average grades of 1.2 per cent Cu, 0.4 kg/t U, 0.5 g/t Au, 2.6 g/t Ag as contained mineral resources. Olympic Dam is expected to produce >200 000 tonnes of Cu and 4200 tonnes of U3O8 from 9.8 million tonnes of ore in 2004, making it the 12th largest Cu producer in the world. One of the impediments to achieving targeted rates of production has been oversize material (>0.9 m) reporting to stope draw points. A major contributor to oversize material may be overbreak along pre-existing structural weaknesses from stope walls and backs during the production life of a stope. Underbreaking to structures can also have a detrimental effect on the performance of a stope. In an effort to understand the influence of structural geology on stope performance, WMC Resources and SRK Consulting partnered during 2003 to refine the current system of structural mapping, and to use historical data to produce a structural interpretation covering a large part of the mining area. The interpretation has been wireframed in DATAMINETM into a three-dimensional structural framework model. To date, there are more than 600 structures of >50 m strike length incorporated into the structural framework model, which covers a study area 1500 m + 600 m + 350 m. A back-analysis exercise to assess the influence of interpreted structures on overbreak and underbreak was completed for laser-surveyed stopes.

Jan 1, 2004

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

By A Scott, I Onederra

Most iron ores occur in mine benches as complex mixtures of lithologies and ore types. This significantly complicates their characterisation for both blast design and fragmentation modelling. A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful engineering models are currently available to blasting engineers and consultants, and more sophisticated approaches using mechanistic descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The engineering or empirical models that are in more general use within the industry, such as the Kuz-Ram model, require appropriate data if they are to generate useful fragmentation predictions. Some of these models have reached significant sophistication and have made very useful contributions to both routine blasting operations and the exploration of new blasting paradigms. However, these models struggle to adequately deal with rock that is as complex as iron ore. This paper reviews the characteristics of the most successful blast fragmentation models available to the industry and discusses approaches to the derivation of suitable rock mass properties to adequately describe blast fragmentation in a range of iron ores.CITATION:Scott, A and Onederra, I, 2015. Characterising the blasting properties of iron ore, in Proceedings Iron Ore 2015, pp 481–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By M I. Pownceby, J Manuel, S Suthers, A Poliakov, E Donskoi, N Ware

"The mining industry is constantly seeking methods for optimising the exploitation of mineral resources, such as iron ore, in a sustainable and eco-efficient manner for economic and social benefit. When faced with resources that have mineralogical or textural complexity, poorer grades or geological variability, it is particularly important to apply a comprehensive geometallurgical approach to the development of the mining operation, from resource definition through to processed product. Integral to this approach is the quantitative characterisation of representative samples across the whole orebody.A key factor that associates the geological characteristics of iron ores to their processing response is ore texture. While the classification of samples on the basis of chemical or physical properties alone is often not sufficient to predict their processing behaviour, classification and quantification of texture types can be effectively correlated to metallurgical performance in processes such as blending, beneficiation, pellet making, sintering and ironmaking. This paper describes some of the research conducted by CSIRO pertaining to the design and rationale of a texture-based classification system for Australian iron ores; some of the tools developed and used to apply such classification; and the application of the generated data to quantifying, modelling and predicting sintering behaviour and performance in the blast furnace.CITATION:Suthers, S, Pownceby, M I, Manuel, J, Ware, N, Donskoi, E and Poliakov, A, 2016. Geometallurgical Characterisation of Australian Iron Ores – from Ore to Processed Product, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Giurco

As part of global systems of mineral production and consumption, the Australian minerals sector is facing sustainability challenges across technological, social, ecological, economic and governance domains, as well as between local, national and global scales. To ensure that the Australian minerals sector progresses towards sustainability, it is imperative to understand the possible ways in which AustraliaÆs mineral resources could support sustainable futures. A significant research gap exists between the complex nature of questions concerning minerals sustainability and the reductionist methods available to deal with them. This paper argues the need for broader, more integrated approaches to questions concerning minerals sustainability, which can address multiple human perspectives, complex and æmessyÆ patterns and processes across multiple organisational, temporal and geographical scales and whole systems of mineral production and consumption. To inform the development of a new approach to minerals sustainability, this work reviews the contemporary understanding of the Australian minerals sustainability problematic, from the perspective of the Australian minerals sector (Minerals Council of Australia), the Australian research sector (Mudd 2007a, 2007b; Mudd and Ward 2008) and a multi-scale international project (MMSD 2002). This review shows the focus of current responses to the minerals sustainability problematic, identifies the need for an integrated approach to questions of minerals sustainability and addresses how different approaches are informed by underlying and unarticulated assumptions about the tolerability of tradeoffs between different societal goals, the treatment of uncertainty and the application of different conceptual geographical, organisational, temporal and life cycle scales to define the minerals sustainability problematic. The Mineral Resources Landscape proposed, offers an expanded conceptualisation of minerals sustainability, to link minerals production and consumption in an integrated assessment across the entire minerals supply chain, connecting social, ecological, technological, economic and governance domains across local, national and global scales. The key leverage points governing change in the Mineral Resources Landscape are identified as: the material source, extraction and production technologies, level of service and value, and consumption patterns. Mapping the key challenges facing the minerals sector, as identified in the review herein, indicates that the boundaries defining traditional conceptualisations of minerals sustainability focus on the material source and technology and ignore two very key drivers of the Mineral Resources Landscape û the æservicesÆ minerals offer to society and the æconsumption trendsÆ which assimilate these services into society. Understanding these overlooked aspects of the Mineral Resources Landscape, along with the conventional areas of focus, is essential for identifying the Australian minerals sector as a provider of sustainable mineral services. This insight prompts a reconsideration of the role of minerals services and consumption trends, together with the role of the material source and technology in shaping change and the emergence of sustainable systems of Australian minerals production and consumption, across multiple scales and domains.

Jan 1, 2009

By Lynn DR, Wadley GB

The Australian gold industry has made large steps forward in the last few years. This progress has been driven by improvements in mining and processing technology, the high price of gold and by a favourable legislative, political and taxation environment. This paper concentrates on improvements in gold project development, process engineering and technology as seen by BHP Engineering, Perth, Australia.The paper describes technical aspects of successful gold project development including metallurgical testwork, feasibility studies, choice of process flowsheet (gravity, heap leach, carbon in pulp (CIP), carbon in leach (CIL) or other routes). It sets out our views on plant design, plant construction, procurement and project management.A case study for a small plant recently completed in the Philippines is presented as a solution to the problems often encountered in treating quartz vein gold deposits.

Jan 1, 1990