Search Documents

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

The influence of strongly chemisorbed solutes such as oxygen and sulphur on the rates of reactions at the gas-liquid iron interface is briefly reviewed. Deductions from recent studies of the rates of decarbur- ization of carbon-saturated liquid iron indicate ideal adsorption behaviour for sulphur over a wide temperature and composition range. This is in fair accord with available infor- mation on surface tensions in the Fe-C-S system. Previously unpublished results for the kinetics of the 14C02-CO exchange reaction are in accord with ideal absorption of oxygen on liquid iron. The derived value for the ideal adsorption coefficient of oxygen at 1550¦C is in quantitative agreement with measurements of the depression of surface tension in the Fe-0 system. Consideration is given to the applicability of such results to the violently agitated systems of steelmaking.

Jan 1, 1980

By P Odins

Traditionally, stratigraphic deposits have been represented by a large number of gridded surface and product analytical models, related to each other by naming convention. This approach, though suitable for structurally simple stratigraphic deposits, does not lend itself well to addressing the complex style of stratigraphic deposits which are becoming more prevalent. In addition, the sheer number of individual gridded models involved makes it very difficult to keep a consistent audit trail of the overall deposit model. Recently, a new enhanced block model structure known as Horizon Adaptive Rectangular Prism (HARP) models was introduced to address these issues. An HARP model is specifically designed to allow stratigraphic units to be represented with virtually no loss of structural integrity, by allowing the tops and bases of the individual HARP blocks to ‘bend’ in concert with the input surfaces. By bringing together the best of grid modelling, triangulation modelling, block modelling and grade estimation, the HARP model opens up many exciting new opportunities for the stratigraphic geologist or engineer to take their model further than was previously possible. Examples of improvements in modelling methodology using a HARP model include: the ability to represent complex normal, reverse and thrust faulting; the ability to store thousands of additional analytical, geotechnical or calculated variables in each individual block; advanced visualisation, manipulation and plotting capabilities; and the ability to calculate volumes and resources against complex, three-dimensional (3D) solid pit designs. Finally, several ‘real world’ scenarios, illustrating how this advancement in modelling technology can benefit a wide range of mining professionals are detailed. These examples demonstrate how productivity gains can be made in both long-term resource modelling and short-term ‘week by week’ geological modelling as an adjunct to mine planning.

Aug 22, 2011

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By A Giyose, V Malysiak, K Davey

Batch flotation tests were conducted on a haematite-bearing Sishen iron ore slimes sample from South Africa using reverse cationic flotation. The effect of grinding on flotation performance, the flotation response of various key impurities in the sample, and the feasibility of increasing metal recovery by refloating tailings in a scavenger flotation step were investigated. The test results indicate that reverse cationic flotation is effective in rejecting impurities from the iron ore sample tested. From a head grade assaying 6.4 per cent SiO2, 2.14 per cent Al2O3, 0.402 per cent K2O, 0.082 per cent P and 0.194 per cent TiO2, the levels of impurities were reduced to 1.83 per cent SiO2, 0.88 per cent Al2O3, 0.095 per cent K2O, 0.066 per cent P and 0.174 per cent TiO2 in the final concentrate at a Fe recovery of 74 per cent. The flotation response of SiO2, Al2O3 and K2O were found to be better than that of P and TiO2. The testwork demonstrated that grinding to 80 per cent passing about 49 microns is essential for upgrading the Sishen iron ore to produce >67 per cent Fe concentrate grade. This grind size corresponds to about 80 per cent liberation of haematite from the gangue minerals. Fe recoveries up to 76 per cent were obtained by refloating the rougher tailings in a scavenger stage, with little effect on the final concentrate grade. Size-by-size Fe recovery data obtained indicated that particles below ten microns were mostly lost in the desliming stage conducted prior to flotation whilst some reported to the froth by entrainment. Some of the coarser haematite-gangue composite particles reported to the froth product by genuine flotation.

Jan 1, 2009

By S Serp, M Duchateau, P Chevreux

Molten salt reactor (MSR) is a promising advanced reactor system aiming to the transmutation of minor actinides such as americium in order to reduce the inventory of ultimate nuclear waste. The fuel is a molten salt in which actinides are homogeneously dissolved in the liquid phase. A chloride salt may be retained for this concept, as it provides low melting point, high solubility of actinides, harder neutron spectrum. To avoid corrosion and precipitation issues, molten salt composition has to be carefully controlled with impurity content as low as possible. Obtaining pure actinide chlorides without contaminants such as oxide, oxychloride, hydroxide and water is still a challenge. To prepare actinide-bearing salt, the chlorination of actinides oxides was investigated in an unstirred reactor under flowing gas as solid-gas reaction. The carbochlorination of PuO2 were performed in the temperature range of 600 to 800°C with chlorine gas as a chlorinating agent and the presence of solid carbon. PuCl3 was successfully synthesised by this method and characterised by X-ray diffraction measurements but some impurities such as oxide phase remain inside the formed product. Refinements of anhydrous and hydrated PuCl3 phases by Le Bail method were also performed for crystalline materials definition. Conversion mainly depends on the chlorinating temperature and the contact between the oxide and the chlorinating agent. A conversion value of 70–80 per cent was achieved at 700°C from PuO2 with quite high specific surface area. The conversion rate was not improved with increasing the chlorination time. The volatilisation of Pu was observed during the carbochlorination experiments. To avoid a loss of Pu caused by sublimation, the chlorination temperature should be limited to 650°C despite that the conversion of PuO2 to PuCl3 was enhanced by increasing temperature. Both carbochlorination and hydrochlorination of AmO2 were also carried out leading to the formation of AmCl3. These first results suggest that americium oxide was chlorinated more readily than plutonium oxide. The purity of produced PuCl3 and AmCl3 still deserves further investigations.

Jun 19, 2024

By K Osten, N Scagliotta, G Lane

Oceana Gold (New Zealand) Limited operates the Macraes Gold Mine near Dunedin on the South Island of New Zealand. The orebody is mineralogically complex and comparatively low grade requiring a series of unit processes and resulting in a relatively complex plant. As part of Oceana GoldÆs ongoing Business Improvement program, a concerted effort has been made to focus on operational efficiency. One aspect of this has been the efficient use of energy in the gold recovery process. A benchmarking process has been developed for the Macraes operation that includes comparison with other operating mines and theoretical design. Criteria for determining operational efficiency have been developed. While benchmarking is, in theory, a simple process, this paper looks at putting benchmarking into practice by catering for variability in ore and associate processing methods. The unit processes discussed include the comminution circuit, flotation plant, pressure oxidation plant and gold recovery circuits.

Jan 1, 2004

By D Bradshaw, E Forbes, M Edraki, M Tayebi-Khorami, E Manlapig

There is an increasing trend in the extraction and development of copper resources from complex deposits. These deposits pose mineral processing challenges, as they often contain low grade disseminated copper ore with high levels of impurities particularly arsenic. Although arsenic is a naturally occurring element, the concentrations of arsenic can be magnified by mining and mineral processing activities. Therefore, while arsenic has no significant market value, its presence in the ore deposit will have production, environmental and human health implications. The mining industry’s approach to life-of-mine planning has improved significantly in recent decades and managing arsenic is not an exception.CITATION:Tayebi-Khorami, M, Edraki, M, Manlapig, E, Forbes, E and Bradshaw, D, 2018. Arsenic pathways in copper mining – sustainability issues and potential solutions, in Proceedings Life-of-Mine 2018, pp 60–63 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D J. Brake

The underground metalliferous mining industry continues to change under the influence of many factors including, to name a few, new mining techniques and equipment, new approaches to risk management, more stringent safety and health standards, new employment practices and orebodies become deeper and often lower grade. In addition, the same technological revolution and plummeting cost of technology that has brought the GPS, smart phones and digital cameras to the general population is also working its way through the mining industry impacting on communications, automation and process control as well as introducing major efficiency and productivity dividends. However, not all factors are positive including, in particular, the issues of carbon costs and electrical power. This paper explores some of the trends affecting ventilation in hard rock mines, some of the existing and likely future challenges and some of the potential future solutions to these issues.CITATION:Brake, D J, 2013. Ventilation challenges facing the metalliferous sector, in Proceedings The Australian Mine Ventilation Conference , pp 3-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By T D. Jolly, L A. Balzan, A R. Harris, Z Bauk

"The availability of real-time data in any process control system is critical for effective management of that system. At MMG LXML Sepon Copper Operation in Lao PDR, controlling the copper grade of the feed to the leaching circuit is paramount for maximising both productivity and copper recovery. Since 2008, real-time analysis data has been available to the process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor, and highly accurate results on copper grade have allowed the process engineers to strictly control blending to overcome the variability in plant feed grade. The availability of real-time analysis data is crucial, as effective sampling of this stream is both difficult and error-prone, being only a snapshot in time of highly variable ore stockpiles, as well as having significant laboratory turnaround delays. Periodic sampling is used to verify the Geoscan data as accurate. Since its installation, the copper result has been the most critical output of the Geoscan. In recent times, the process engineers have sought to utilise other results from the Geoscan to further improve and control the process. One measurement of particular interest involves the real-time measurement of calcium and magnesium as a gauge of ore feed gangue acid consumption. To satisfy this end, accurate measurement of calcium and magnesium is becoming increasingly more important and has been the subject of ongoing collaboration between Sepon and Scantech, the manufacturer of the Geoscan. This paper discusses this work, describing the calibration process and results obtained, while also providing a basis for Geoscan use in operations to enable enhanced process control for all potential Geoscan users.Citation:Balzan, L A, Jolly, T D, Harris, A R and Bauk, Z, 2016. Greater Use of Geoscan On-belt Analysis for Process Control at Sepon Copper Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 231–238 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011

By Ring R. J, Waters D. J, Vautier F. E, Fulton E. J

Laboratory leach tests have been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid (permonosulphuric acid) as an alternative oxidant to pyrolusite in the leaching of uranium ores. Results demonstrated that Caro's acid reduced acid consumption in leaching and the lime required for neutralisation of tailings liquor. The uranium extraction was unaffected by choice of oxidant.Following this study, Interox Chemicals Pty Ltd arranged a plant trial using Caro's acid at the Nabarlek uranium mill of Queensland Mines Ltd. The trial confirmed that significant savings in acid and lime usage can be achieved under plant conditions.Plant operations also demonstrated that Caro's acid has a number of significant operating advantages over pyrolusite.Queensland Mines Ltd have recently decided to convert their leaching process from pyrolusite to Caro's acid. The new system is expected to be fully operational by mid 1983.

Jan 1, 1983

RME has a vision for a new grinding plant operational paradigm made possible by RMEÆs fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RMEÆs range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RMEÆs vision of a æliner profile versus profitabilityÆ commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

After some 50 years of worldwide research in relation to coal pillar mechanics and design as well as numerous workshops and technical papers related to these issues there is still some significant disagreement as to the approach one should adopt in the assessment and design of a coal pillar. Of course there are many different types of coal pillars that fulfil a wide range of roles at any particular mine and in this instance it is appropriate to have a 'tailored' approach for each pillar type in relation to the role it fulfils. However where it can become very difficult for the mine operators is when various researchers or consultants use or recommend significantly different approaches for the same type of pillar fulfilling the same role. By 1999 two pillar design techniques had been developed specifically for the Australian underground coal mining industry (ie The University of New South Wales Pillar Design Procedure, UNSW PDP and Analysis of Longwall Tailgate Serviceability, ALTS) and several other pillar design techniques were being practiced by individual consultants. The Australian industry hoped to resolve the issue of what technique to use for each pillar type and role, when it funded UNSW in 2000 to develop a 'Systems Approach to Pillar Design'. The findings of the abovementioned project were published in 2005 and while every attempt was made by UNSW to include the views of various local and overseas researchers and consultants it would be fair to say that a unified approach to pillar design in Australia was not adopted as a result of that project. This is the experience of one country where there has never been one central group solely undertaking such research in relation to pillar design (such as the Chamber of Mines in South Africa). This paper explores the Australian experience in terms of pillar research and what that experience may offer to researchers in Australia and other countries. At the First Australasian Ground Control in Mining Conference (2003) the first 'update' of the ALTS Design Methodology (ie ALTS II) was presented. In subsequent years the ALTS database was continually updated and significantly expanded such that it now includes detailed information in relation to both the tailgate (148 cases) and maingate belt road (58 cases). In addition to tailgate roof support and chain pillar design, the current version of ALTS (referred to as ALTS 2009) includes a maingate belt road roof support design module. This paper is also intended to update and summarise the development and application of the ALTS Design Methodology for longwall gateroad design over the last decade both directly and in the context of coal pillar research conducted in Australia over the last 15 years.

Nov 25, 2010

By S H. Begg

There is strong evidence that many major oil and gas (O&G) projects are plagued by large cost and schedule overruns, or significant underperformance in productivity. Similar evidence exists for large mining projects. This paper claims that uncertainty is the underlying reason why projects fail to deliver the metrics used to justify their investment, or to deliver the economic value possible if alternative decisions had been made.Most technical and economic analyses are performed to reduce uncertainty to help make decisions. Decision-making is about ranking alternatives and choosing the best; rarely are precise predictions required, if this is even possible. Better uncertainty assessment is one of the keys to better decisions, thus better business outcomes. To get better decisions it is suggested that the focus or reward/penalty incentives be shifted away from the quality of outcomes to the quality of decisions. High-quality decisions are those that are generated from the skilled use of the tools, methodologies and processes from the discipline of decision analysis.Uncertainty is quantified by probability, which is a degree of belief in the truth/falsity of some proposition about a quantity relevant to a decision, such as volume of in-place resource, future price or action of a competitor. The probability a person ascribes to a proposition depends upon their information set; hence probability is subjective – it is not an inherent attribute of the quantity of interest or the physical system.The above simple observations have profound implications for modelling approaches, how they deal with uncertainty, the use of data to help assess uncertainty and the reliability of information provided by subject-matter experts. The limited circumstances under which frequency data (from spatial or temporal variables) can be used to assign probabilities is also reviewed.People, in general, are subject to a range of biases and cognitive errors. Research with O&G subject-matter experts shows that their expertise offers little or no protection from making errors in probability assessments and other judgements.CITATION:Begg, S H, 2016. Decisions, decisions – uncertainty, variability, modelling and psychology, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 9–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Shiels O. J

The paper reviews developments in general galvanising in Australia, including a brief history of the industry and its technology. The changes in galvanising process technology are covered, as well as developments in galvanising bath design, materials handling and pre-treatment. Developments in zinc management through the use of aluminium and nickel alloys are discussed. The paper addresses the cost components of general galvanising and relates this to the competitive position of general galvanising against other coatings used for protecting steel. The environmental aspects of the general galvanising industry in Australia are outlined with respect to the utilisation of process chemicals, problems associated with their disposal and developments in filtering and regeneration of process solutions. The current status of the industry is assessed in terms of zinc usage and usage trends. Likely changes in technology which may impact on the general galvanising industry in the future are reviewed.

Jan 1, 1993

By S C. Dominy

Grade control programs aim to deliver economic tonnes to the mill via accurate definition of ore and waste. The foundation of a successful program is high quality sampling supported by geology and a suitable data management and modelling system. Underground sampling methods include chip, channel and panel samples; grab/muck pile samples; and drill-based samples. Grade control strategy is related to mining method and orebody type. Sampling protocols must be designed to suit the style of mineralisation in question. Holistic studies focussing on ore mineralogy and gold particle deportment, size and distribution are required for sample collection and preparation protocol optimisation through ‘Theory of Sampling’ application. Where possible, such programs should be undertaken early in the life of a project. Appropriate assaying procedures are also required. Program implementation will require suitably skilled individuals to train and mentor staff, with ongoing Quality Assurance/Quality Control (QA/QC) monitoring and review will allow protocols and staff to be updated as required.

Aug 22, 2011

By N Udugampola, d A. Seneviratne, X Ai, B Li

With the evolution of mining technology, wireless mesh networks using low-power, long-range technologies such as LoRa are increasingly utilised in underground mining operations. Efficient deployment of wireless nodes in such mesh networks necessitates understanding radio wave propagation behaviour in underground mines. While existing propagation models either remain theoretical or apply only to basic geometric shapes, we propose a practical approach to analyse radio wave propagation behaviour in underground mines using ray tracing simulations with reconstructed 3D models of targeted environments. Our method validated using a set of corridors as a substitute for underground mine environments, involves constructing a 3D model using SolidWorks from LiDAR scans of the environment and performing wireless transmission simulations using the MATLAB ray tracing toolkit. Our simulation model is also fine-tuned by calibrating the raytracing parameters based on real-world LoRa transmission experiments in the actual environment corresponding to the 3D model. This method offers a practical solution for optimising wireless node placement in underground mines, facilitating efficient network deployment while reducing the need for extensive physical testing of radio wave transmissions.

Sep 1, 2024

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

By D Pienaar, B McFadzean, C T. O’Connor

Collector and frother molecules in sulfide mineral flotation are thought to have separate roles in the flotation process, where the collector selectively hydrophobizes the mineral surface and the frother adsorbs onto the bubble surface, inhibiting bubble coalescence. Molecular interactions have been observed between these molecules which allow them to co-adsorb at each of the respective interfaces, improving pulp phase recovery. This study investigated the molecular interactions between sodium diethyl dithiophosphate (SDEDTP) and hexanol, and the mechanism by which these interactions improve the recovery of galena. In this study each of the respective interfaces were investigated for the adsorption of SDEDTP. The adsorption of SDEDTP on galena was measured by UV-Vis spectrophotometry and isothermal titration calorimetry. At the air-water interface foam stability and pulp bubble coalescence was used to quantitatively discern if there are interactions between SDEDTP and hexanol. Microflotation and induction time experiments were performed to determine the effect of SDEDTP, hexanol and their mixtures on mineral recovery and bubble-particle attachment. The results of all these tests were collated to determine if SDEDTP-hexanol mixtures synergistically improve sulfide mineral recovery. It was found that SDEDTP reduced bubble coalescence in the pulp demonstrating activity at the airwater interface. Together SDEDTP and hexanol synergistically enhanced foam stability. This indicated that there are attractive molecular interactions between these reagents. Even though DTP did not adsorb onto galena, DTP-frother mixtures synergistically improved the recovery and attachment probability of this mineral. Adsorption studies with aeration showed that DTP in the presence of a frother transfers from the air-water interface to the galena mineral-water interface during bubble-particle collision. It was proposed that the transfer of hexanol through the thin film enhanced the kinetics of film thinning between the bubble and the particle by destabilising the thin film thus improving pulp phase mineral recovery.

Aug 24, 2022