Search Documents

By D Kubik, K The

The New Zealand (NZ) Transport Agency’s Waterview Connection will complete Auckland’s Western Ring Route, a 47 km north–south motorway alternative to Stage Highway 1. The project is being delivered by the Well-Connected Alliance comprising the New Zealand Transport Agency (NZTA), Fletcher Construction, McConnell Dowell Constructors, Obayashi Corporation, Parsons Brinckerhoff NZ, Beca Infrastructure and Tonkin & Taylor.The project involves construction of 5 km of new motorway, nearly half of it underground connecting State Highway 20 (SH20) to State Highway 16 (SH16). The underground portion of the project incorporates twin 13.2 m inside diameter (ID) tunnels 2.4 km long, each carrying three traffic lanes, one for north-bound traffic and one for south-bound traffic. The tunnels are being driven by a 14.46 m outside diameter (OD) 2400 t, tunnel boring machine (TBM) shield that was assembled and launched at the southern portal. It will be turned and re-launched at the northern portal for the return drive to the southern portal where it will be disassembled. This paper presents two major temporary works elements contributing to the successful launch of the TBM: the TBM assembly crane platform and the TBM shove frame and associated components.Tunnel boring machine shield assembly – crane platformThe TBM shield was delivered to site in subassemblies ranging in weight from 100 to 380 t. It was initially proposed to use a 750 t crawler crane sitting above the tunnel portal headwall to assemble and disassemble the TBM. However, this did not have sufficient capacity to allow the TBM shield to advance clear of the tunnel before disassembly commences. To reduce the crane’s working radius a temporary steel crane platform was developed that is supported on the side walls of the tunnel approach trench. This has enabled a smaller, less expensive, 600 t crawler crane to be used and will allow the TBM shield to clear the tunnel before disassembly.Tunnel boring machine launch – temporary worksTo launch the TBM a purpose built steel frame was required for the TBM thrust rams to react against. The shove frame had to be able to transfer the thrust loads from the TBM shield to the ground below and thrust wall behind. A range of potential thrust loads and jacking patterns were examined to develop the design load cases for the shove frame. The shove frame was used to launch the TBM at the southern portal and to re-launch it at the northern portal. Elements of the shove frame will also be used to support the portal faces during the TBM arrivals.CITATION:Kubik, D and The, K, 2014. Waterview Connection – temporary works for tunnel boring machine?launching, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The New South Wales coal industry is a highly mechanised well organised industry which has developed from an annual production of slightly less than 13 million tons in 1950 to over 33 million tons in 1969. Although continuous miners were not introduced into the mines until 1950, by Jillle 1969 the percentage of coal won by these units was 87.3. The paper describes mining conditions in the various coalfields of the State, their complexities and problems and how these have been dealt with. The introduction of fully mechanised long wall faces has presented a challenge which has been accepted and descriptions of systems in use are discussed. Major expansion of the industry is anticipated to meet the requirements of the growing Australian steel industry, for local power generation and to meet the increasing demands of overseas markets.

Jan 1, 1971

By Fogarty J. G H

Ausmelt Technology has a unique capability of removing the impurities, phosphorus and sulphur, from the feed materials to the process. Sulphur is removed to the gas phase almost completely because of the interactions of ore and coal in the reaction region at the top surface of the slag bath. Phosphorus is removed to the slag phase, with both basic and higher, controlled iron oxide levels in slag being achieved in the process. The significance of these features of the process relate to the production of pig iron with very low levels of these impurities for the further processing to steel, and to the treatment of high phosphorus and high sulphur raw materials. The marketability of pig iron and the raw materials are discussed in relation to this feature of Auslron.

Jan 1, 1999

Rational decision making is generally perceived by managers of operations to be a delicate process of committing large sums of money and putting other people's life at risk. Consequently most managers may argue that the decision process requires good judgement, intuition and extreme caution; and not one easily made through the use of fancy mathematical algorithms and computer programs. The advent of artificial intelligence and expert systems in the computer industry combined with recent technological innovations in mathematical and economic problem solving is sure to change this perception. PARETO OPTIMALITY is an economic and a mathematical optimisation concept applied to solving real life operational problems; and one that the current volatile economic forces would require managers to employ because it is virtually real. REALISMM is a computer software package developed using the principles of Pareto optimality, dynamic programming, optimal clustering of information and decision maker interaction to generate decision maker preferred solutions. REALISMM has scope for artificial intelligence and expert systems application for cases where the decision maker is unsure about his objective preferences.

Jan 1, 1993

By A Grace, C Sennersten, T Taylor, A Davie, R Lyu, D Pentecost, C A. Lindley, J Craig, L De Macedo Camargo

Many underground mine void spaces are not suitable for human entry due to unprotected roofs, instability or having an unknown safety state (eg if they are many decades old). Investigations of these voids may nevertheless be important for general mine safety, for example to detect propagating collapses or water accumulation, prevent accidental intrusion by new developments or drilling to reassess old spaces for re-mining. Robots are an ideal technology for investigating these spaces, especially flying, rotary-wing robots that can access and map vertical structures and spaces while avoiding rocks, water and mud that have accumulated on void floors. To operate in underground mines, we are developing customised unmanned aerial vehicles (UAVs) as well as interactive 3D virtual models of the vehicles and their underground environments for controlling vehicle operation and visualising incrementally gathered survey data. Using a game/simulation engine to provide an interactive interface for UAV operation makes it possible to orchestrate external spatial information and video feeds with in-game cameras for optimal visualisation that is not limited to the position, orientation or field of view of cameras mounted on the UAV. First and third-person points of view with respect to the UAV are provided, together with 2D and 3D gaze tracking to provide effective interfaces for geology and mine engineering experts without the need for specialist UAV piloting skills. Ongoing work is addressing the provision of greater levels of autonomy for these vehicles to support mapping well beyond the line of sight of operators and geological characterisation of rock surfaces using sensors mounted on them, including miniature X-ray fluorescence and Raman spectrometers. Gathered data is fed into more general 3D models of the mine, block models and orebody so that the UAVs function as elements of a mobile perceptual system for intelligent mining.CITATION:Sennersten, C, Lindley, C A, Davie, A, Lyu, R, Grace, A, Evans, B, Pentecost, D, Taylor, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. Unmanned aerial robots for remotely operated and autonomous surveying in inaccessible underground mine voids, in Proceedings Third International Future Mining Conference, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By L O. Filippov, A Piçarra, I V. Filippova, N P. Lima, K Silva

The reverse cationic flotation using the starch as depressor of iron oxides is the most efficient upgrading process when is applied to the simple systems composed by hematite/magnetite and quartz. The fundamental studies performed with iron ore samples from different deposits over the world (Brazil, Russia, Mexico) confirmed the inefficiency of starch when the silica content in the concentrate is controlled by Fe/Mg-bearing minerals. The main approaches for solving these issues focused on using new collector formulations or new depressants. However, the alternative depressants tested inhibited flotation of quartz or were less efficient as iron oxide depressant. In this work, a comparison between new amidoamine collector with conventionally used etheramine and oleate collectors in the flotation of pure minerals and actual iron ore samples was performed. The electrophoretic mobility, contact angle and infrared spectroscopy measurements allowed to deduce the hindrance effect as main mechanism of selective adsorption of the amidoamine on the quartz surface compared to hematite and kaolinite. Molecular modelling studies revealed that this steric hindrance effect can be explained by the combination of the "shield" formed by the coordinating water molecules on the (001)-D2 hematite surface and the large volume of the amidoamine head group. The amidoamine tested as collector without use of a depressant showed excellent flotation selectivity allowing the total flotation of quartz from a mixture with hematite. High collector performance and selectivity were confirmed during reverse flotation of quartz using continuous flotation column (D = 500 mm; H = 4000 mm) and allowed to produce the iron concentrates with more than 60 per cent of iron from the rejected slimes samples of Vargem Grande 2 processing plant (Iron Quadrangle, MG, Brazil). The new collector allowed to develop flexible flotation flow sheets to process the iron ore with a complex gangue mineralogy and unlock the old altered tailings and slimes product as new resources

Aug 24, 2022

The rocks of Waihi and the surrounding district are almost entirely rhyolitic and ande5itic in character. Sedimentary rocks, with the exception of some surface deposits of clay loosely compacted conglomerate, etc., and one or two thin and broken beds of a very poor lignite, occasionally changed by igneous agencies into a bituminous coal, are almost absent. In the shafts sunk by the Waihi and Grand Junction companies outside the outcropping andesitic area of the Martha Hill, more than one old surface or lake bottom has been passed through. At these points layers of sand, consolidated volcanic mud and tuff, accompanied by numerous broken fragments of imperfectly silicified wood have been enccuntered, but these occurrences may, for the purpose of this paper, be neglected.The youngest rock of the district are rhyolites, probably of Pliocene age. At least three distinct classes of rhyolitic lava, each possessing features of unusual interest, may be made out. None of these, however, is gold-bearing. The youngest flow, a light-coloured, fine-grained rock, is remarkable owing to its enclosing at times fragments of carbonised wood, varying in size from mere specks up to quite large pieces of almost pure charcoal. Rhyolitic tuff is also met with. The rhyolites cover a large extent of nearly flat country east, south, and west of Waibi, here and there rising into barren, stony hills.Below the rhyolites, geologically speaking, but for the most part. forming hills which bound the rhyolitic plain, or rise out of it as isolated patches, come ahdesites of older...

Jan 1, 1902

By Brown H. R, Wright E. A

The authors identify the workable coal seams, their distribution in relation to quality and economic occurrence and relate their analytical characteristics to industrial use. The development of established collieries is also discussed with regard to increased production demand.The authors also indicate the potential of the coal resources of the Southern District and postulate their ultimate development.INTRODUCTIONThe Southern Coalfield yields 30 per cent of the total production of bituminous coal in New South Wales. The economic potential of the coalfield was examined last by Harper (1915). Since that time additional knowledge has been gained by prospectors, mining companies and public authorities. Expansion in the steel industry and the building of power stations on the coalfields together with improvements in fuel technology, mining methops and road transport have resulted in production of coal from seams mice thoughtto have no economic value.DESCRIPTION OF THE COALFIELDFor the purpose of this paper the term Southern Coalfield includes also the South-Western Coalfield which together comprise the following Coal Districts:IllawarraDouglas ParkWollondilly-NattaiMoss Vale-Berrima (Hanlon, 1953).Geographically the coalfield is contained by the Illawarra Range in the east, the Shoalhaven River to the south, the Wollondilly River to the west, and in the north by a line...

Jan 1, 1958

By D Thorburn

This paper reviews the history of environmental assessment in New Zealand with reference to mineral developments. Emphasis is given to larger more controversial projects particularly metal mines. The changing role and application of the Environmental Protection and Enhancement Procedures is examined in the context of changes in the government's environmental administration and the response of the Ministry of Energy's resource allocation group. Conclusions are drawn on the effectiveness of the present environmental assessment activities and on the allocation of administration of priorities in the Ministry. The Ministry of Energy has effectively ceased to exist.

Jan 1, 1990

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

By R Harding, T Hunt

For the past 120 years, Portland cement manufacture has been undertaken on the shores of the Whangarei Harbour in northern New Zealand. Through a serendipitous conjunction of geo-chemistry, the argillaceous marl found on Limestone Island in the harbour and Tikorangi Hill provides a perfect mix of the various elements required for strong and durable cement. Golden Bay Cement, and its predecessors, have been the guardians and managers of the use of these minerals. As the demands of the concrete industry have increased, so have the needs of the manufacturing process. Careful mapping of the resource at both Portland and Wilsonville Quarries has been undertaken. This has allowed the Company to change the Quarry operation from a purely volume basis to one of selection and blending of constituent minerals. Within the manufacturing process, change has also been introduced. Analytical techniques, using x-ray fluorescence spectrometry, microscopy and the application of modem data collation, has allowed fine tuning of the process. The Company now produces an increasing diverse range of products for both the domestic New Zealand market and exports to various South Pacific countries. This paper discusses the processing of limestone and æcement rockÆ into cement clinker, an intermediate synthetic mineral ground into cement. It examines control and blending regimes, and some methods used in determining process efficiency. An important technique ærediscoveredÆ has been the application of microscopy to clinker.  Examination of the major silicate minerals enables interpretation of the kiln processing and feedback to process operators. It also enables a prediction of indicated performance when ground into cement. Examples this paper give an insight into the use of minerals from Northland in some of the more important construction projects in modem New Zealand.

Jan 1, 1999

To date Iron Monarch is the most important Australian source of iron ore and since HH5 has produced about 84 million tons of direct shipping ore containing 62 per cent iron and 3 per cent manganese.Previous geological work, mainly by Rudd, Edwards and Miles is reviewed and the results of later exploration by quarrying and drilling are discussed and modified interpretations of both stratigraphy and structure are advanced. Renewed study of the mineralogy of the iron ores is advocated.The Iron Monarch orebody lies on the up-thrown side of a major transcurrent fault that truncates it on its northern boundary. The nearby Iron Knob orebody is believed to occupy a horizon that is some thousand feet stratigraphically above Iron Monarch.The origin of the ore cannot be explained by any simple theory; development probably took place over a long period of time from Lower Palaeozoic to Tertiary.INTRODUCTIONIron Monarch orebody has supplied the Australian iron and steel industry with the greater part of its ironstone requirements since the establishment of the Newcastle steelworks in 1915. Annual production of direct-shipping ore has exceeded three million tons but declined slightly after 1956 when Iron Prince was brought into production. Total production of ore from Iron Monarch to the end of 1962 is about 84,000,000 long tons containing some 55,000,000 tons of metal.The deposit (Lat. 32°44'30"S : Long. 137°08'30"E) is 34 miles north-west of Whyalla, on the western shore of Spencer Gulf. A 42 in. gauge railway connects Iron Monarch and its associated small town of Iron Knob with Whyalla (Fig. 1).For the purpose of this paper Iron Monarch includes Iron Knob and the intervening jaspilite hill known as Substation Ridge, and the description of the general geology necessarily 'Assistant Chief Geologist, The Broken Hill Proprietary Co. Ltd.This paper was presented at the Annual Conference of The Institute, 14-24th August 1968.

Jan 1, 1964

By B Roache, J O’Brien, M Gray

Admixture use in cement products is commonplace in the construction and mining industries. Many Australian mines have an operational concrete batch plant and stock hydration control and water reducing admixtures. The benefits of admixture use, especially in shotcrete is understood and well documented. Cemented rock fill (CRF) is used to fill stope voids and create stable vertical and undercut surfaces at some Australian mines. These mines generally mix rock fill with a slurry of cement and water without the use of admixtures. Recently published work on optimisation of CRF mixes has mainly focused on the strength increases associated with changes to the mix grading proportions by the addition of fines, but not focusing on the potential benefits of admixture use. Admixture use in CRF may be the simplest CRF optimisation method, as the admixtures will often be added by the push of a button at the batch plant. A CRF testing program was undertaken to test the benefits of admixture use in terms of strength gain, using hydration control additives (HCA) and high range water reducer (HRWR) admixtures. Rock fill gradings were strictly controlled in the test process to allow clear definition of the difference admixtures provide in compression at 28 days. The testing results define admixture associated strength gains in a 6 per cent general purpose (GP) cement by dry weight CRF mix (131 kg of cement/m3). Costings have been developed to allow a mine operator to understand the cost benefits of admixture use in CRF due to reduced operating costs. Operational efficiency advances and a suggested admixture implementation plan for CRF optimisation is offered.

Nov 29, 2022

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

Previous methods for measuring the flow of solids in Jnrdraulic conveying have not considered the important effects of slip velocity and particle concentration. In this paper an extension of the method proposed byShirato et al. (J. Chem. Engng. 'Japan, 1: 164-167) for determining mass flow in a vertical conduit is outlined.The present method consists of measuring' the volumetric flow of the slurry (by a magnetic flow meter for instance) and the density of the slurry in two pipe sections of different diameters. Effects of variation of slip withparticle concentration, not previously considered, are allowed.Problems involved in estimating the density of a slurry from differential pressure measurement are discussed.The major problem is the uncertainties in estimating frictional losses due to the wall in two-phase flows. The greater reliability of a more "direct" technique, such as by 'Y-ray absorption, for measuring solid concentration is emphasized.

Jan 1, 1971

The presence of gold or tin in a particular place in payable quantities may be suspected from geological and prospE;cting reports. It behoves the engineer by judiciously spaced boreholes or pits to establish whether the place is exploitable with profit, and it is the purpose of this paper to set out the ways in which this is done. The various types of deposit to be considered occur in Malaya, Thafland and Borneo, in which countries the writer spent four years in estimating alluvials.The methods described were used in actual practice both by the writer and previous engineers for the same company. The subsequent exploitation of the alluvials evaluated by the methods given below shows that the recovery was as good as, and sometimes higher than, expected. No claims are made to the originality of the methods, but it is 'felt that they may be new to some engineers and< interesting to others contemplating alluvial testing.

Jan 1, 1942

By B Nielsen, H Lehto, B Musuku

"The demand for fine and ultra-fine grinding associated with the processing of more challenging, finer grained orebodies and the global driver of minimising energy consumption has been an increased focus in our industry. Outotec’s stirred milling technology, the high intensity grinding mill (HIGmill™), was launched in 2012 in response to this industry need. First Quantum Minerals Ltd selected HIGmill™ technology for its Kevitsa mine in Northern Finland. The 700 kW mill is grinding copper rougher concentrate to improve copper/nickel separation and copper recovery. Selection of the HIGmill™ followed mineralogy analysis and laboratory and pilot testing for HIG milling in parallel with flotation tests to determine optimum grind size and energy input.The paper discusses the challenges and successes of the test work, manufacture, installation, commissioning and subsequent operation of the mill. Grinding performance is presented and a comparison between predicted and operating energy efficiency is made. In addition, the various steps to optimise wear rate and minimise maintenance and downtime are made, with particular reference to internal geometry of the mill.Citation:Nielsen, B, Lehto, H and Musuku, B, 2016. Design, Installation, Commissioning and Operation of Fine Grinding Technology at the Kevitsa Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 59–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By V Ser, R Crosbie

To date, Anglo American Research Laboratories (AARL) has carried out several projects, based on the techniques developed in AMIRA International LimitedÆs (the mineral industries research association) AMIRA P9 project, to develop models for several Anglo Base Metals flotation plants. Further detailed analysis of the data which was generated has realised additional benefits: the various hydrodynamic measurements were useful in comparing cell operating parameters to literature sources, while the laboratory batch tests give an indication of plant recovery potential. A detailed cell by cell mass balance, which is a critical feature of the modelling process, is in its own right a valuable diagnostic tool. Several examples of how this can be used to highlight potential improvement areas in the plants are presented. The added understanding gained from sampling each cell is clear and this is shown to more than compensate for any necessary modifications needed to allow sampling to take place. The model fitting process generates an ore floatability distribution, which is used in the JK SimFloat simulation package to assess the effect of possible changes to each of the circuits. An example of an actual circuit change as a result of this approach is presented. The current limitations of and the potential improvements to the modelling process are also briefly discussed. Future models will be extended to include enhanced size and mineralogical information where the basic models suggest this has potential to improve understanding.

Jan 1, 2005

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By A Batnasan

The main techniques for removing phosphorus as an impurity element in iron ores are physical separation (eg magnetic separation, flotation) and chemical separation (acid leaching, alkaline leaching and bioleaching) processes. When phosphorus occurs in iron ores as phosphate minerals (eg apatite), physical separation techniques are available to remove the gangue minerals from iron ores. On the other hand, chemical separation techniques are suitable for reducing phosphorus levels when phosphorus is associated with iron oxides and hydroxide minerals (eg hematite and goethite) in iron ores. In this study, the dephosphorisation behaviour of high‐phosphorus iron ore was investigated using a combined alkaline roasting and water washing route. Roasting experiments were conducted in a laboratory electric muffle furnace using various concentrations of sodium hydroxide (0–50 g/kg-ore) at different temperatures (100–800°C), varying prolonged roasting times (0–2 h), and different particle size fractions (-45 – -250 μm) of iron ore. Subsequent water washing experiments were employed at various pulp densities (30–1000 g/L) and different times (30 s – 60 min) at ambient temperature. Hematite and goethite were the main minerals in the high-phosphorus iron ore identified using X-ray diffraction (XRD) analysis. The iron ore assaying 63.40 mass % Fe (total), 0.240 mass % P, 4.53 mass % SiO2, and 4.87 mass % Al2O3 were determined using X-ray fluorescence (XRF) analysis. The results showed that the dephosphorisation rate of the iron ore was reached 40 per cent under roasting with 50 g/kg-ore NaOH at 300°C for 2 hours followed by water washing for 30 s with a pulp density of 300 g/L, reducing phosphorus level from 0.240 mass % to 0.142 mass %. At the same time, the iron grade was reduced from 63.4 per cent to 59.5 per cent, caused by an iron loss. Results suggest that the phase transformation of goethite induces the dephosphorisation of high-phosphorus iron ore under alkaline roasting conditions

Aug 22, 2022