Search Documents

By Johnson T, Huynh D

The State Electricity Commission of Victoria is conducting a program of research and development into alternatives to the use of conventional boilers for the generation of electricity from brown coal. The objectives of the program are to reduce the cost of electricity generation and also to improve the thermal efficiency so as to reduce the emission of greenhouse gases and other pollutants. The program presently includes the following four technologies: Hydro-thermal Drying, Direct Coal Fired Gas Turbine, Integrated Gasification Combined Cycle, and Steam Fluidised Bed Drying. The Hydro-thermal Drying process produces a combustible coal-water-slurry fuel which is suitable for use in a coal fired gas turbine. The coal fired gas turbine has the potential to produce electricity at a lower cost than conventional power stations and when combined with a steam cycle, it will also use significantly less coal. The Integrated Gasification Combined Cycle process gasifies the coal, cleans the gas, and then bums it in a gas turbine/combined cycle. This process is being developed in Europe and the USA in order to meet their stringent emission regulations. It offers Victoria cleaner more efficient and cheaper electricity.

Jan 1, 1992

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

The Telfer main dome open pit is operated by Newcrest Mining Limited at a current production rate of 50 Mt/a from a pit dimension compromising 2 km strike length, 1 km width and 250 m depth. As part of the refeasibility of the Telfer operation undertaken early this decade, Newcrest identified that an underground sublevel cave (SLC) operation along with an increased scale of open pit would support a new plant targeting the processing of gold and copper ore at 17 Mt/a rates. The SLC was initiated in late 2006 and broke into the open pit in late 2009. This situation is unique across the mining industry where a cave breakthrough was planned and occurred within an active large open pit operation. The SLC broke though into the west side of the Main Dome open pit into a specially prepared bench that was left at the 5384 RL of cut-back stage 3. A main haulage ramp is within 100 m from the edge of the cave breakthrough zone and this ramp passes down to the active levels which are progressing toward the 5200 RL. This paper presents insight into the mine planning and risk management associated with continued operation of the open pit operation while an active SLC breaks through. The cave breakthrough presents unique areas for risk management as there is potential for rapid propagation and subsidence. To support the undertaking, mine design and major hazard management planning has been carried out. Focus areas include; dual ramp system design, preloading the breakthrough area, monitoring of cave propagation and air gap using a seismic system and deep hole extensometers, wall stability and subsidence monitoring using radar and prism systems, and key trigger and response planning.

May 1, 2010

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Since the last occasion on which I spoke to you on this subject there has been a considerable increase in the mechanical ventilation of Western Australian mines.The following table compares the figures for 1939 with those of 1941. The type of fan most commonly used is the limit load fan. On account of its higher mechanical efficiency it has very largely superseded the multivane fan with forward curved blades.Two fans of the propeller type are in use and these have given very satisfactory service. This type of fan also has a high mechanical efficiency particularly at the correct duty for maximum efficiency.The maximum efficiencies obtainable from the various types are, for "multivane" 670/0, for "limit load" 75%, and' for aerovane 7810/0.References to propeller fans with variable pitch have appeared in the technical press, but no detailed d~scription has been issued. The advantages of these fans for mine ventilation are not obvious. An aeroplane is required to operate over a wide range of duties, while the speed of the motor for maximum efficiency is pl'actically constant. In such circumstances the propeller can be adapted to the particular work it has to do by varying the pitch of the blades. In a mine the speed of the fan can be varied to suit.the conditions, and it would appear that variable pitch is not necessary while there is a reasonable range of fans to choose from.The question of the correct position for the fan still comes in for considerable discussion. Exhausting fans at the surface have the support of time and custom, and in many cases this represents the only reasonable arrangement. Such fans should be fitted with an evase, especially in the case of fans with a high outlet velocity such as the aerovane types.It is claimed that there are advantages in having the fan at the surface where it is readily available for inspection and maintenance. Experience has shown that these advantages are more apparent than real. Fans will run for long periods with no attention other than occasional greasing and cleaning, and modern electric motors will run without attention for very long periods.In some instances the expense of a power cable to take current to the fan may be saved by placing it on the surface, but in the majority of cases...

Jan 1, 1941

By T A. Short, P L. Brown

Kestrel Mine co-disposes around 1.5 Mt of fine (2SO4/t and to date around 9 Mt has been deposited. The mine plans to co-dispose of approximately 39 Mt of material, creating a dump with a maximum height of 35 m and a disturbance footprint of 260 ha. Benign materials suitable for rehabilitation are severely limited and no successful rehabilitation strategy has yet been demonstrated. A rigorous measurement and modelling program is resolving outstanding issues associated with acid rock drainage (ARD). The objective of the program is to develop and validate a strategy for dump rehabilitation that will control ARD and allow for mine closure. The strategy includes using a soil cover to reduce water flux into the dump to control the overall oxidation rate and to control effluent release. Monitoring of the oxygen distribution and water flux in the uncovered material commenced in February 2001 and monitoring in waste under a trial cover commenced in February 2002. Carbonaceous and sulfidic oxidation rates have been measured. Initial modelling indicates that the carbonaceous material has the general effect of slowing the rate of pyrite oxidation, lowering the maximum sulfate production rate and extending the time to oxidise all the sulfides. The combined approach of measurement and modelling provides a sound basis for assessing the performance of the trial cover and predicting the long-term quality and quantity of effluent at the base of the rehabilitated waste dump.

Jan 1, 2003

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

Solution transport of gold and silver has occurred as a result of the chemical weathering of many Western Australian epigenetic gold deposits. Evidence for the remobilization of gold exists in the form of small crystalline octahedra, mustard gold, flake gold, and coatings on iron-oxide. This "secondary" gold is of high purity (low silver content). It is believed that the high chloride content of laterite profiles combined with the acid produced by the oxidation and hydrolysis (ferrolysis) of iron has caused dissolution of Au/Ag and Au/Te alloys. Gold, and less frequently silver, is subsequently reprecipitated in the profile nearby.Pyrite, which is a ubiquitous accessory of gold in vein or lode systems, is probably an important source of iron for the development of acidity. Where carbonate is abundant in the primary assemblage, neutralization directs the oxidation of sulphide to a path which produces thiosulphate, and an alternative type of Au/Ag oxidation process. Sulphide/carbonate ratios in the vein system, and adjacent wallrock are seen as important in determining the course and extent of remobilization in the oxidized zone of gold deposits.

Jan 1, 1984

Continuous, steady-state laboratory flotation tests showed that the recovery of cha1copyrite from a naturally occurring ore, under conditions closely resembling those of plant practice, could be expressed in terms of a first order rate equation.Tests on full-scale plant flotation cells, using impulse tracers, indicated ideal mixing of the pulp in the cells.It was demonstrated that values of first order flotation rate constants can onlv be obtained from conventional methods of analysis in special cases.Analysis of a plant sampling campaign by the author supported a first order kinetic equation for two mineral species, and for the individual size fractions of one of these.The effect of stage-addition of reagents is interpreted in kinetic terms.

Jan 1, 1966

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021

By M Bouare, C Holland, K N’Diaye

Two adjacent open pits in Mali hosted by deeply weathered saprolitic materials were mined consecutively over the course of approximately 12 months. During excavation, both pits experienced significant displacement and tension cracking as the result of deeper than expected depth of weathering coupled with relatively steep slope angles and significant groundwater. In response, geotechnical and operations teams overcame numerous monitoring challenges with prisms and radar to develop a simple and effective monitoring system coupled to a Trigger Action Response Plan (TARP) which enabled continued safe operations while reducing ore loss. Observations of previous slope performance of these two pits allowed for greater confidence in empirical failure runout calculations that was used to specify the standoff widths for the exclusion zones in the pit. Back analysis of the slope as-built performance after the first indications of slope distress was also conducted. The back analysis was used to confirm rock mass parameters for modelling while being utilised as a reality check for the stability analysis. The stability analysis indicated that leaving a large step-out or buttress would not prevent the displacement, resulting in some ore being sacrificed to ensure the safety of personnel. Key learnings from this experience highlight the importance of: • up-to-date geological interpretation of the depth of weathering • ensuring slope design guidance is reviewed and updated as latest information (ie geology and monitoring) is received • having multiple complementary slope monitoring methods to ensure redundancy • ensuring visual observations and as-built performance are utilised as a reality check to provide greater confidence in stability analysis and design guidance.

Jun 22, 2022

By J W. Glatthaar, M Mavotoi

The occurrence of fluorine in the copper/gold concentrates produced by Ok Tedi Mining Limited has provided a series of challenges to metallurgists since 1988. Although fluorine is distributed throughout the gangue minerals contained within Ok Tedi ores, itsÆ presence in talc and phlogopite (naturally floating fluorosilicates) has proven to be the predominate sources of fluorine in the final concentrate. Initial treatment for the fluorosilicates consisted of the use of a carboxy-methyl cellulose depressant added to the flotation cleaners. This was superceded in 1998 with the installation of a fluorine reverse flotation process for the removal of naturally floating fluorosilicates from the final concentrate when the fluorine content of the final concentrate exceeds smelter-defined trigger points. The fluorine reverse process is similar to by-product molybdenite concentrate production in that sodium hydrosulfide is used to depress copper/gold flotation whilst allowing the fluorosilicates to float. The process was installed in two parallel modules (to match the existing grinding/flotation modules at Ok Tedi), each consisting of a closed rougher/cleaner circuit configuration. Both rougher and cleaner cells are Jameson Cells from MIM Process Technologies, with the selection based on both processing characteristics and available construction space. This paper discusses both the nature of fluorine in-, and its removal from-, Ok Tedi copper/gold concentrates.

Jan 1, 2003

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005

By T Muzondo, C Prins, D De Vaux, R Schouwstra

The Mogalakwena Platinum Mine in the northern limb of the Bushveld Complex is Anglo American PlatinumÆs only open cast operation exploiting the Platreef. The Platreef, which extends along the basal contact of the Bushveld Complex, is geologically and mineralogically a much more complex orebody than the Merensky and UG-2 reefs. Changes in the footwall and the genesis of the Platreef translate into a number of rock types being present. These rock types vary in hardness and recovery potential and present challenges to metallurgical staff trying to optimise the concentrator. A true understanding of the implications of treating these rock types is required if the maximum value from this orebody is to be obtained.In order to more accurately forecast production and incorporate ore variation in the mine plan and comminution and flotation circuits, a geometallurgical approach to managing the operation has been used and is being further developed.CITATION:Schouwstra, R, De Vaux, D, Muzondo, T and Prins, C, 2013. A geometallurgical approach at Anglo American PlatinumÆs Mogalakwena Operation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 85-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R Wynn, T J. Akroyd, C Costa

In an environment of lower zinc prices, falling revenues and reducing zinc feed grades, Century mine implemented a fast-tracked capital upgrade program in less than 15 months. The program was designed to increase ore milling throughput capacity by 20 per cent and optimise the capacity of the flotation plant to increase zinc recovery by approximately 2.5 per cent whilst maintaining final zinc concentrate grade.A key aspect of this program was minimising capital expenditure by better utilising existing capacity and only adding capacity where absolutely required to address critical processing bottlenecks. By gaining an understanding of plant process bottlenecks and future ore blends, and by carefully selecting appropriate technologies for particular specific flotation applications, maximum return on minimal capital investment was achieved.The close collaborative work achieved between the metallurgy processing department and other operational departments on-site was also critical to the success of this project. This work increased the mining and processing capacity of the mine and port site respectively, such that the full value of the process plant modification could be achieved.Capital payback on this investment was achieved in approximately three and a half months.This case study demonstrates the extra value to a mining business that can be achieved through fully understanding the mining/processing value chain and by careful targeted action to address critical bottlenecks in the processing chain from the mine through to the port site.CITATION:Akroyd, T J, Wynn, R and Costa, C, 2014. MMG Century Mine, a case study – maximising project net present value through targeted capital expenditure and process optimisation against a backdrop of falling metal prices and feed grades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 417–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The Olympic Dam copper/uranium deposit was discovered in 1975 and subsequently commenced production in 1988 at a rate of 1.5 Mtpa using the sublevel open stoping mining method. In the following five years the operation underwent two optimisation programs that have increased mine output to the current rate of 3.4 Mtpa of ore. The pre-expansion requirements were annual development of approximately 10 000 m and the placement of around 500 000 m 3 /yr of cemented backfill. Previous to 1995 all hoisting was carried out by the Whenan shaft. The Robinson shaft was commissioned during that year to hoist increasing development mullock tonnages and to allow for increased ore hoist via the Whenan system. In 1996 WMC committed to expanding the output of the operation from 85 000 tpa (1996/97 budget) copper metal to 200 000tpa. The corresponding increase in mine ore production requires expansion to a nominal rate of 9.0 Mtpa. To achieve these increased tonnages, major hardware installations will include sinking of a third shaft capable of hoisting in excess of 9.5 Mtpa, a rail haulage horizon utilising automatic trains, expansion of the existing backfill plant to a production capacity of over 1.8 million m 3 /yr, increasing long term development rates to 15 000 m/yr and increasing the production drilling and blasting rates in line with the higher stope production output. This paper provides detail into the intended hardware (shafts, equipment, etc) of the mining system, and outlines the intended long-term operation and management of the operation. Of particular note is the background requirement of ensuring existing production targets are met to provide critical cashflows into the project during the period of expansion.

Jan 1, 1998

By R Sterk, B Reid

The Konongo Gold Project is located on the western margin of the 125 Moz Ashanti Gold Belt in Ghana, West Africa. It is situated 60 km along strike of the world-class mineral system at Obuasi and is interpreted to lie on the same controlling regional shear system.The project is operated by Signature Metals, a subsidiary of the Liongold Corporation, and is managed and funded by the Liongold Corporation.Historic underground operations at Konongo produced 1.6 Moz Au at a head grade of 11.8 g/t Au, from eight operations spread along 16 km of the shear system. Mining focused almost exclusively on free-milling gold in quartz, ignoring the gold-bearing sulfide mineralisation associated with the quartz veins. Underground mining ceased in 1986.In 2013, Signature Metals re-focused the program at Konongo to assess the viability of mining the sulfide ore sustainably. This led to the first campaign review of the historic underground data and resource potential since mine closure. The Obenemase mine was the first of the eight operations to be assessed as part of this campaign.Large amounts of legacy data have survived for Obenemase and several historic resource estimations have been completed based on these data. The data typically consisted of hand-drawn sections and plans, and ledgers of commonly incomplete drilling and sampling data. Some drill core have been lost over time, but a large amount of quarter-core and half-core as well as pulps and rejects are still available. Previous resource estimates had a low confidence value because all the available assay and geological data were integrated effectively with the estimates, resulting in a lack of understanding of both grade and geological continuity.This project built a new geological model for Obenemase that greatly enhances the understanding of the controls on mineralisation using a thorough approach of re-surveying, re-cataloguing and re-logging. This model led to an increased degree of confidence and a subsequent upgrade of resource classification, and created several previously unrecognised strong exploration targets. The resulting resource estimates increased the value of the project by 100 per cent.This paper emphasises and highlights the importance of a well-understood geological model on the confidence of a resource estimate and how this may directly impact on the project’s ‘bottom line’.CITATION:Sterk, R and Reid, B, 2014. The Konongo Gold Project, Ghana – an example of how geology makes all the difference to a resource estimate, in Proceedings Ninth International Mining Geology Conference 2014 , pp 467–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By S H. Algie, E J. Knoblauch, I A. Lovatt, S G. Doig

Mill operating teams are expected to engage in a perpetual quest for process improvement – pushing the boundaries of practical process limits and testing new technology to achieve the next step-change in plant performance. Often the barrier to improvement lies in gaining management approval for process changes.Getting approval for investment in novel technology carries an added degree of difficulty, particularly in risk-averse operations, when it challenges conventional wisdom. A case in point is a new technology for controlling variability in slurry distribution. There is a widely held view that less-than-specified classification efficiency and spraying and roping of individual units in a hydrocyclone cluster, must be accepted as unavoidable. That these are wholly correctable deficiencies resulting from unequal loading of the individual units seems a bold claim. Wouldn’t the high turbulence of pumped slurries overcome all potential for segregation of solids? This paper discusses how the task of developing confidence in a new technology can be approached by a combination of physical modelling at small scale, and full-scale operating experience. Proving efficacy then leads to the next task: demonstrating value. Again, the particular technology serves as an example that could be of value to others developing relatively low-cost technologies. A high-pay-off as an investment may be achieved with improvements in metallurgical performance that are small in relation to normal process variations. This has led to an exploration of how process simulation modelling could be used, in conjunction with production data, to provide a benchmark for the expected change, which could be expressed in monetary terms.The next goal, which is currently being achieved in operating plants, is to realise the greater value now available through the optimisation of cyclone configuration, which becomes practical when the confounding effects of cluster instability are removed through equal loading.CITATION:Doig, S G, Algie, S H, Lovatt, I A and Knoblauch, E J, 2018. Investing in new process improvement technology: reducing the risk of implementation – a way forward, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 571–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018