Search Documents

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By P Trout, B Macaulay

Ridgeway Gold Mine (RGM) is an underground sublevel caving (SLC) operation that is owned and managed by Newcrest Mining Limited (NML). Production drill and blast practices are critical to the success of the SLC method at RGM. SLC production ring precharging was introduced in November 2001 to enhance these practices and deliver safety, productivity and cost improvements. Current precharging practices require up to two rings to be loaded ahead of the ring to be blasted in each drawpoint. The explosive may be required to remain in the up-holes for periods of four weeks or more prior to blasting. During this æsleepÆ time it is subjected to repeated shock from the blasting ofadjacent rings and from rings in adjacent drawpoints. The project described in this paper was designed to gain an understanding of the factors affecting explosive performance in the precharging environment and to develop explosive products and operating practices that would meet RGMÆs requirements in terms ofsaf ety, reliability and blast outcomes. Several months oflaboratory and field testing were required to characterise the explosive and quantify the effect of post-loading blasting shock. These results were used to determine the most appropriate loading and sleep time criteria for RGMÆs precharging practices. In addition, the information is being used to guide the development of the next generation of emulsion explosives for use in underground precharging operations.

Jan 1, 2005

By R Jacobs

"The Jaguar project is relatively unique in that it was evaluated, financed, built and operated to completion within the last ten years, providing the opportunity to holistically review and reconcile expectations against the actual outcomes. It is a case study that allows wider conclusions to be drawn with respect to the risks and opportunities involved with project evaluation and execution.Jaguar is located in the Leonora Mining District of Western Australia and was commissioned in mid-2007 as an underground accessed, single high-grade volcanic-hosted massive sulfide (VHMS) deposit with an on-site concentrator, producing copper and zinc concentrates exported via the Port of Geraldton to South-East Asian markets.The feasibility study (FS) had several iterations (JML, 2005a); the last dated July 2005 was specifically targeted to secure project funding, and summarised the reserves-only portion of the resource and its planned exploitation. The commissioning of the mine was the transition for the owner Jabiru Metals NL from junior explorer to producer and the project was the dominant asset of the company.Jaguar operated through several significant deviations from the linear project plan set out in the FS, including the Global Financial Crisis (GFC), a corporate takeover and disruption to the mine plan from the onset of material geotechnical issues. Whilst the GFC or mining disruption were not specifically predicted in the FS or peer reviews, the generic effects of the events were assessed in the project risk assessment and they influenced subsequent management decisions. In parallel to the internal project-specific risks, the short planned life of Jaguar was a risk to the continuation of the corporate entity which was being addressed by significant investment into brownfields exploration to extend or replicate the project, and ultimately added value such that attracted a corporate takeover.Holistically, the project delivered the returns predicted in the FS, but in a much different guise than was expected. This paper will describe the reality of operations compared with the study predictions and expectations through the perspective of the project and corporate risk assessment.CITATION:Jacobs, R, 2016. Jaguar base metals project case study – has reality reflected the study?, in Proceedings Project Evaluation 2016, pp 86–97 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C M. Zammit, N Cook, F Reith, C L. Ciobanu, J Brugger

The role of biological agents in the gold mining industry is currently limited to the use of microorganisms in bioleaching and bioremediation. However, there is a variety of possibilities in which biotechnology could aid the mining industry in the future. In this article we discuss the potential for the development of these novel biotechnologies and the role they can play in the exploration for new gold deposits, the processing of ores and the post-mining remediation of sites. The development of these biotechnologies has been enabled by rapid advances in our molecular-level understanding of the role microorganisms play in the solubilisation, dispersion and precipitation of gold. An understanding of the distribution of microbial species in soils overlying mineralisation can be utilised to develop bioindicator systems that assist with gold exploration. An in-depth knowledge of how microorganisms interact with gold complexes is being used to develop in-field biosensors, supporting exploration. Processing technologies may be improved based on advances in our understanding of the interactions between microorganisms, ore minerals, cyanide and gold. For instance, cyanide-producing microorganisms are being investigated for use in in situ leaching of gold. In turn, the use of cyanide-utilising microorganisms for the degradation of cyanide is being explored. Combined, the implementation of these biotechnologies in the gold mining sector may revolutionise the industry, leading to greener, more efficient exploration for and extraction of gold.CITATION:Zammit, C M, Cook, N, Ciobanu, C L, Brugger, J and Reith, F, 2013. Possible future applications of biotechnologies in the gold industry - a prospective approach, in Proceedings World Gold 2013 , pp 233-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Solution transport of gold and silver has occurred as a result of the chemical weathering of many Western Australian epigenetic gold deposits. Evidence for the remobilization of gold exists in the form of small crystalline octahedra, mustard gold, flake gold, and coatings on iron-oxide. This "secondary" gold is of high purity (low silver content). It is believed that the high chloride content of laterite profiles combined with the acid produced by the oxidation and hydrolysis (ferrolysis) of iron has caused dissolution of Au/Ag and Au/Te alloys. Gold, and less frequently silver, is subsequently reprecipitated in the profile nearby.Pyrite, which is a ubiquitous accessory of gold in vein or lode systems, is probably an important source of iron for the development of acidity. Where carbonate is abundant in the primary assemblage, neutralization directs the oxidation of sulphide to a path which produces thiosulphate, and an alternative type of Au/Ag oxidation process. Sulphide/carbonate ratios in the vein system, and adjacent wallrock are seen as important in determining the course and extent of remobilization in the oxidized zone of gold deposits.

Jan 1, 1984

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By M Akhtar, E Jak, M Shevchenko

This article presents an overview of the experimental phase equilibria studies of S-containing systems (Ni-Sn-S, Cu-Sb-S, and Cu-Sn-S) and As-containing systems (Fe-Sb-As and Fe-Sn-As). These systems improve the prediction capabilities of FactSage in a 20-component ‘Cu2O’-PbO-ZnOFeO- Fe2O3-CaO-SiO2-S-(Al2O3-MgO-CrO-Cr2O3-Na2O)-(As, Sn, Sb, Bi, Ag, Au, Ni, Co) system for complex pyrometallurgical operations during both refining and recycling. Experiments involved equilibration at predetermined temperatures (300–1200°C) with or without preheating, followed by rapid quenching in a brine. Quenched samples were then directly measured using an electron probe microanalyser. For the Ni-Sn-S system, liquid phases (NiS- and SnS-rich mattes and liquid metal) and solid phases (Ni1+xSn, SnS, Ni3Sn, FCC-Ni, Ni1-xS, NiS2, Ni3Sn4, SnS2, Sn2S3 and β-Ni3S2) were observed. A new Ni3Sn2S2 phase was found to melt incongruently. For the Cu-Sb-S system, liquid metal, matte, FCC-Cu, digenite, Sb, CuSbS2, Cu3SbS3 and Cu3SbS4 phases were observed. For the Cu-Sn-S system, liquid metal, matte, digenite, SnS and Cu3Sn phases were found at liquidus.

Jun 17, 2024

By G Marling, A Calderon, J Harris, P Kirsch, M Shi, D Sprott, A Kirsch

Large-scale infrastructure construction needs to comprehensively manage risks that can impact the health and well-being of many people, from workers (temporary, contracted or full time), to families and surrounding communities. This paper starts with an analysis of incidents (injury, fatality, other damage) in tunnel construction between 2000 and 2014 and assesses the distribution of these events by continent, year, and severity of outcomes. These incidents are then analysed and mapped to a framework of hazards derived from RISKGATE (2014). A comparative register of current tunnel construction risk management guidance is derived from current Australian codes of practice and this register is also mapped to the RISKGATE framework of hazards to identify where coal industry knowledge may offer utility to the tunnelling industry.An initiative of the Australian Coal Association Research Program (ACARP), RISKGATE is an interactive online risk management system developed to assist the mining industry in implementing continual improvement in the management of major unwanted events. To date, a comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, outbursts, coal bumps and bursts, human/machine interface, manual tasks, slips/trips/falls, inrush and occupational hygiene. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper proposes and outlines how knowledge within the RISKGATE platform could be applied to managing the significant health and safety risks associated with tunnelling. The authors suggest that to varying degrees the knowledge already captured in RISKGATE is likely to be transferable to tunnelling construction operations. Please note that this paper focuses on tunnel construction and does not address risk management of tunnels in operation (eg road transportation or utility networks).CITATION:Kirsch, P, Kirsch, A, Calderon, A, Marling, G, Harris, J, Shi, M and Sprott, D, 2014. Management of health and safety in tunnelling – application of Australian coal mining knowledge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Since the last occasion on which I spoke to you on this subject there has been a considerable increase in the mechanical ventilation of Western Australian mines.The following table compares the figures for 1939 with those of 1941. The type of fan most commonly used is the limit load fan. On account of its higher mechanical efficiency it has very largely superseded the multivane fan with forward curved blades.Two fans of the propeller type are in use and these have given very satisfactory service. This type of fan also has a high mechanical efficiency particularly at the correct duty for maximum efficiency.The maximum efficiencies obtainable from the various types are, for "multivane" 670/0, for "limit load" 75%, and' for aerovane 7810/0.References to propeller fans with variable pitch have appeared in the technical press, but no detailed d~scription has been issued. The advantages of these fans for mine ventilation are not obvious. An aeroplane is required to operate over a wide range of duties, while the speed of the motor for maximum efficiency is pl'actically constant. In such circumstances the propeller can be adapted to the particular work it has to do by varying the pitch of the blades. In a mine the speed of the fan can be varied to suit.the conditions, and it would appear that variable pitch is not necessary while there is a reasonable range of fans to choose from.The question of the correct position for the fan still comes in for considerable discussion. Exhausting fans at the surface have the support of time and custom, and in many cases this represents the only reasonable arrangement. Such fans should be fitted with an evase, especially in the case of fans with a high outlet velocity such as the aerovane types.It is claimed that there are advantages in having the fan at the surface where it is readily available for inspection and maintenance. Experience has shown that these advantages are more apparent than real. Fans will run for long periods with no attention other than occasional greasing and cleaning, and modern electric motors will run without attention for very long periods.In some instances the expense of a power cable to take current to the fan may be saved by placing it on the surface, but in the majority of cases...

Jan 1, 1941

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By Vernon PN

The Eossing Uranium Mine is a high tonnage low grade open pit operation using acid leaching for uranium extraction and ion exchange and solvent extraction for solution purification. Advanced technology, much of it computer based, has led to major economies that have contained operating unit costs over the last four years in the face of double figure inflation. An improved ore reserve block model and mine planning system have achieved a considerable reduction in the stripping ratio. Drilling and blasting costs have decreased some 25%, mainly by the introduction of heavy ANFO explosive. A centralised computer control centre for the metallurgical plant has increased labour productivity resulting in improved process control. The all-staff workforce is united with management in the objectives of creating a safe, healthy, working and living environment and a prosperous company, capable of contributing to the wellbeing of the nation and the shareholders. This situation has been brought into being by an equal opportunity policy coupled with a management system emphasising open two-way communication through all levels in the organisation. The success of this policy is highly apparent in the morale and productivity of the workforce.

Jan 1, 1986

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

By Phil N

A large number of experiments have been carried out by many workers on the recrystallization of deformed and subsequently annealed metals and alloys. Although observations on single crystals are of great importance in the study of the recrystallization textures of deformed and annealed metals, very little of this work deals with material in this form.Since, in deformed metals, the stress concentration is greatest at the grain boundaries and along the planes of slipping, it is to be expected that recrystallization will start in these regions. For example, in polycrystalline aluminium (1),:1: (2), copper (3), a-iron (4) and brass (5), (6), which had been deformed by cold-rolling, drawing, pressing or stretching and then annealed, the new grains first appeared in the boundaries of the original crystals, whilst in the case of cupronickel (7) and iron (8), recrystallization commenced along the slip planes of the deformed material. Deformed and annealed single crystals of aluminium (9) and cadmium (10) first start to recrystallize along slip planes and in deformation twins.The present work deals with the process of recrystallization of single crystals of lead after deformatjon by creep.Two factors enter into these experiments that were not met with in other work on this subject. Firstly, lead...

Jan 1, 1940

By M Stevens, M P. Simpson, J L. Mauk

The Karangahake deposit was the second largest producer of gold-silver bullion in the Hauraki Goldfield, New Zealand. New mapping of a 2 + 3 km (6 km2) area demonstrates that hydrothermal alteration surrounds productive veins. Wallrocks proximal to veins are intensely altered and alteration decreases toward the margin of the system.   At Karangahake, distinct zonation of adularia, calcite, epidote, illite and illite-smectite surrounds gold-bearing lodes with unaltered rocks containing magnetite and plagioclase occurring on the margins. Adularia, illite, illite-smectite, and calcite zonation defines hydrothermal alteration extending 2 km to the east of productive lodes. Epidote and adularia zonation occurs proximal to veins. The adularia zone compares well to potassium/thorium studies conducted in the area. Illite zonation is well developed to the east of the veins grading into interstratified illite-smectite containing 5 to 40 per cent smectite 1.5 km from the Maria Lode. Calcite is restricted to the east of the study area occurring in 18 per cent off surface samples. Less altered rocks containing plagioclase and magnetite occur distal to veins. The magnetite occurrence compares well to aeromagnetic studies conducted in the area.   Adularia and coexisting adularia and albite indicate the host rocks were highly permeable. Epidote, illite, illite-smectite and previous fluid inclusion evidence implies temperatures graded from >240¦C in the core of the system to approximately 150¦C on the periphery. The alteration association of quartz, adularia, calcite, pyrite, chlorite, illite and illite-smectite reflects a near-neutral to weakly alkaline water. Calcite occurrence and the absence of zeolite imply the fluid contained significant dissolved CO2.

Jan 1, 2005

Ammonium nitrate-fuel oil (ANFO) explosives are unstable in hot, reactive sulphide-rich ground at Mount Isa. Under certain conditions associated with background heat, moisture, and chemical impurities from natural oxidation, ANFO composites in contact with hot ground disproportionate and the ammonium nitrate can undergo rapid exothermic reactions with sulphide.Reactions can occur in confined charges from prolonged contact with reactive sulphides, or by contamination with sulphide in loading. Partial interaction can result in misfires or premature detonation. Spilt, scattered and unpropagated explosive will undergo further reaction in sulphide-rich environments. ANFO-sulphide interaction is invariably exothermic and causes an irreversible chemical transformation of the ore.The heat generated during reaction may be dissipated, heating the environment, or rapidly accumulated to yield hot spots or areas in excess of 400°C. These can result in forced ignition of bulk sulphide and sustained combustion.Thermal analysis was used to define the critical conditions for ANFO-sulphide interaction and sulphide combustion.The occurrence of incandescent ore is attributed to the thermal interaction between exothermic hydrolysis oxidation, ANFO-sulphide, and combustion processes.Chemical agents and control methods have been developed to prevent ANFO-induced oxidation and combustion.

Jan 1, 1968

This paper reviews the development and operation of a small underground tin mine in NE Tasmania. Tin mineralisation was discovered in the Lottah area in the 1880s with early alluvial and eluvial workings leading to the development of large low grade open pit operations. Apart from short lived activities operations ceased in 1915. Intensive exploration in 1978 - 1981 outlined substantial tonnages of low grade tin mineralisation (0.2% Sn) of open pit material. An underground ore body was also located (800 000 tonnes 0.6 per cent Sn). Spectrum Resources Australia Pty Limited acquired a 98 per cent interest in the property in 1988. Mine and mill development began in early 1989 based on an underground mine utilising trackless mining using room and pillar with fill stoping. The milling circuit involves primary jaw crushing, Barmac secondary crushing to 1 mm, Mogensen and DSM screens with jigs and tables to make a wet concentrate. Final tin concentrates are produced by high tension and magnetic separation. Planned production rates are 500 t/day with a mine life of six to seven years.

Jan 1, 1990

The Lower Proterozoic metasediments of the Pine Creek Geosyncline form a chrono- stratigraphic sequence of mainly greenschist- and amphibolite-grade shallow-marine to supratidal pelites, psammites, carbonate rocks, and volcaniclastics which in places rests unconformably on Archaean basement. Granite and later dolerite intrude the sequence, and are associated with the major orogenic 1800-m.y. event which regionally metamorphosed the sediments. Most mineralisation is stratabound, and can be related at least partly to volcanic activity. Uranium mineralisation is mainly confined to particular carbonate-rich horizons near basement. Other metals are mainly in small hydrothermal deposits near intrusive granite. Specialist studies indicate that uranium was leached from its source rock, and probably carried as carbonate complexes in highly saline fluids at between 100 and 3500 C. Precipitation took place by redox reactions in breccia zones in carbonate rocks; these zones were formed by carbonate solution or diapiric movement of evaporites which preceded the carbonate. Extensive chloritisation in the ore zones suggests metasomatism by Fe- and Mg-rich fluids which may have evolved during dewatering of the evaporites. The main mineralising event took place after the 1800 m.y. metamorphism, and was probably

Jan 1, 1979