Search Documents

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By P Trout, B Macaulay

Ridgeway Gold Mine (RGM) is an underground sublevel caving (SLC) operation that is owned and managed by Newcrest Mining Limited (NML). Production drill and blast practices are critical to the success of the SLC method at RGM. SLC production ring precharging was introduced in November 2001 to enhance these practices and deliver safety, productivity and cost improvements. Current precharging practices require up to two rings to be loaded ahead of the ring to be blasted in each drawpoint. The explosive may be required to remain in the up-holes for periods of four weeks or more prior to blasting. During this æsleepÆ time it is subjected to repeated shock from the blasting ofadjacent rings and from rings in adjacent drawpoints. The project described in this paper was designed to gain an understanding of the factors affecting explosive performance in the precharging environment and to develop explosive products and operating practices that would meet RGMÆs requirements in terms ofsaf ety, reliability and blast outcomes. Several months oflaboratory and field testing were required to characterise the explosive and quantify the effect of post-loading blasting shock. These results were used to determine the most appropriate loading and sleep time criteria for RGMÆs precharging practices. In addition, the information is being used to guide the development of the next generation of emulsion explosives for use in underground precharging operations.

Jan 1, 2005

By R Jacobs

"The Jaguar project is relatively unique in that it was evaluated, financed, built and operated to completion within the last ten years, providing the opportunity to holistically review and reconcile expectations against the actual outcomes. It is a case study that allows wider conclusions to be drawn with respect to the risks and opportunities involved with project evaluation and execution.Jaguar is located in the Leonora Mining District of Western Australia and was commissioned in mid-2007 as an underground accessed, single high-grade volcanic-hosted massive sulfide (VHMS) deposit with an on-site concentrator, producing copper and zinc concentrates exported via the Port of Geraldton to South-East Asian markets.The feasibility study (FS) had several iterations (JML, 2005a); the last dated July 2005 was specifically targeted to secure project funding, and summarised the reserves-only portion of the resource and its planned exploitation. The commissioning of the mine was the transition for the owner Jabiru Metals NL from junior explorer to producer and the project was the dominant asset of the company.Jaguar operated through several significant deviations from the linear project plan set out in the FS, including the Global Financial Crisis (GFC), a corporate takeover and disruption to the mine plan from the onset of material geotechnical issues. Whilst the GFC or mining disruption were not specifically predicted in the FS or peer reviews, the generic effects of the events were assessed in the project risk assessment and they influenced subsequent management decisions. In parallel to the internal project-specific risks, the short planned life of Jaguar was a risk to the continuation of the corporate entity which was being addressed by significant investment into brownfields exploration to extend or replicate the project, and ultimately added value such that attracted a corporate takeover.Holistically, the project delivered the returns predicted in the FS, but in a much different guise than was expected. This paper will describe the reality of operations compared with the study predictions and expectations through the perspective of the project and corporate risk assessment.CITATION:Jacobs, R, 2016. Jaguar base metals project case study – has reality reflected the study?, in Proceedings Project Evaluation 2016, pp 86–97 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C M. Zammit, N Cook, F Reith, C L. Ciobanu, J Brugger

The role of biological agents in the gold mining industry is currently limited to the use of microorganisms in bioleaching and bioremediation. However, there is a variety of possibilities in which biotechnology could aid the mining industry in the future. In this article we discuss the potential for the development of these novel biotechnologies and the role they can play in the exploration for new gold deposits, the processing of ores and the post-mining remediation of sites. The development of these biotechnologies has been enabled by rapid advances in our molecular-level understanding of the role microorganisms play in the solubilisation, dispersion and precipitation of gold. An understanding of the distribution of microbial species in soils overlying mineralisation can be utilised to develop bioindicator systems that assist with gold exploration. An in-depth knowledge of how microorganisms interact with gold complexes is being used to develop in-field biosensors, supporting exploration. Processing technologies may be improved based on advances in our understanding of the interactions between microorganisms, ore minerals, cyanide and gold. For instance, cyanide-producing microorganisms are being investigated for use in in situ leaching of gold. In turn, the use of cyanide-utilising microorganisms for the degradation of cyanide is being explored. Combined, the implementation of these biotechnologies in the gold mining sector may revolutionise the industry, leading to greener, more efficient exploration for and extraction of gold.CITATION:Zammit, C M, Cook, N, Ciobanu, C L, Brugger, J and Reith, F, 2013. Possible future applications of biotechnologies in the gold industry - a prospective approach, in Proceedings World Gold 2013 , pp 233-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Review on Some Research Methods of Mineral Crystal Chemistry and Computer Simulation on Flotation

Sep 13, 2010

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

By Lott JB, Scuffham JB

Until very recently the application of solvent extraction to. the recovery of metals has been considered only for ithose operations where no other process was available. In general, .these operations, have involved metals such as 'f uranium or the rare earths, where the value of metal recovered has been very high. As a result, the tendency has been to consider solvent extraction as a very specialised, high cost technique with minimal application in the base metal industry. Since the mid-1960's this attitude has had to be changed drastically with the development of solvents specifically designed for the selective extraction of individual metals such.ascopper. The result is that solvent extraction must now be regarded as a proven hydrometallurgical technique for the recovery of base metals, and in particular copper. The first significant event in the application of solvent extraction to base metals was the production by General M. Inc. of a compound, designated LIX-63 (R)(1), which was a specific extractant for copper from ammoniacal sns. This did not find a wide application, however, because copper solutions with a pH in the applicable range we more readily treated by conventional techniques.

Jan 1, 1970

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By M Akhtar, E Jak, M Shevchenko

This article presents an overview of the experimental phase equilibria studies of S-containing systems (Ni-Sn-S, Cu-Sb-S, and Cu-Sn-S) and As-containing systems (Fe-Sb-As and Fe-Sn-As). These systems improve the prediction capabilities of FactSage in a 20-component ‘Cu2O’-PbO-ZnOFeO- Fe2O3-CaO-SiO2-S-(Al2O3-MgO-CrO-Cr2O3-Na2O)-(As, Sn, Sb, Bi, Ag, Au, Ni, Co) system for complex pyrometallurgical operations during both refining and recycling. Experiments involved equilibration at predetermined temperatures (300–1200°C) with or without preheating, followed by rapid quenching in a brine. Quenched samples were then directly measured using an electron probe microanalyser. For the Ni-Sn-S system, liquid phases (NiS- and SnS-rich mattes and liquid metal) and solid phases (Ni1+xSn, SnS, Ni3Sn, FCC-Ni, Ni1-xS, NiS2, Ni3Sn4, SnS2, Sn2S3 and β-Ni3S2) were observed. A new Ni3Sn2S2 phase was found to melt incongruently. For the Cu-Sb-S system, liquid metal, matte, FCC-Cu, digenite, Sb, CuSbS2, Cu3SbS3 and Cu3SbS4 phases were observed. For the Cu-Sn-S system, liquid metal, matte, digenite, SnS and Cu3Sn phases were found at liquidus.

Jun 17, 2024

By Visnovsky

The computing needs of a mine planning office vary greatly depending on the staff available and the nature of the work undertaken. Some offices work acceptably with few aids apart from hand held calculators while others use mainframe computers with associated data bases and sophisticated mine planning software. Not every mine planning office requires the big system approach but all can benefit from the intelligent use of small computers. There is virtually no limit to the design problems which can be solved using modern desktop computers. The simple language required encourages engineers to work interactively to facilitate both large and small computations. However a limit does exist in the speed and ease with which solutions can be obtained. The important ingredients for the successful application of such machines are a little computing knowledge, a flexible machine, and an engineer who really understands the mining problems confronting him. If these are available it is possible for the engineer to tailor the program to the task at hand and efficiently achieve the required result.

Jan 1, 1983

By G Marling, A Calderon, J Harris, P Kirsch, M Shi, D Sprott, A Kirsch

Large-scale infrastructure construction needs to comprehensively manage risks that can impact the health and well-being of many people, from workers (temporary, contracted or full time), to families and surrounding communities. This paper starts with an analysis of incidents (injury, fatality, other damage) in tunnel construction between 2000 and 2014 and assesses the distribution of these events by continent, year, and severity of outcomes. These incidents are then analysed and mapped to a framework of hazards derived from RISKGATE (2014). A comparative register of current tunnel construction risk management guidance is derived from current Australian codes of practice and this register is also mapped to the RISKGATE framework of hazards to identify where coal industry knowledge may offer utility to the tunnelling industry.An initiative of the Australian Coal Association Research Program (ACARP), RISKGATE is an interactive online risk management system developed to assist the mining industry in implementing continual improvement in the management of major unwanted events. To date, a comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, outbursts, coal bumps and bursts, human/machine interface, manual tasks, slips/trips/falls, inrush and occupational hygiene. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper proposes and outlines how knowledge within the RISKGATE platform could be applied to managing the significant health and safety risks associated with tunnelling. The authors suggest that to varying degrees the knowledge already captured in RISKGATE is likely to be transferable to tunnelling construction operations. Please note that this paper focuses on tunnel construction and does not address risk management of tunnels in operation (eg road transportation or utility networks).CITATION:Kirsch, P, Kirsch, A, Calderon, A, Marling, G, Harris, J, Shi, M and Sprott, D, 2014. Management of health and safety in tunnelling – application of Australian coal mining knowledge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Bohrn W, Milionis K, Tessmer G, Reidetschlager J

The share of electric arc furnace based steel production is increasing - New technologies for the production of virgin raw materials for EAF production are under development and on the market - VAI has a strong position in the field of scrap substitution technologies with their COREX«-, COREX«-DR and FINMET«-technology. In late-1998 the steel plant SALDANHA was started up successfully. This integrated compact mill is using the COREX«-technology as hot metal and a combined DR-plant as DRI production unit. Also in 1999 the BHB FINMET« plant Port Headland went on Stream.

Jan 1, 1999

By R E. Myers, G N. Phillips

Many of the worldÆs larger iron ore deposits are hosted by rock sequences of Archaean to early Proterozoic age. Most models for the genesis of these deposits are influenced, either directly or indirectly, by the nature of the atmosphere at the time of their formation, and more specifically by the presence or absence of oxygen in the early atmosphere. Since the early-1950s, the geological literature suggests that the Archaean atmosphere was æreducingÆ, and that it may not have contained significant amounts of free oxygen until ca 2 Ga. There are many different definitions of the term æreducingÆ, but the criterion adopted here is whether crustal iron was limited to Fe2+, or whether Fe3+ was also widespread, ie was there scope for redox changes in the state of iron? Significantly, major Australian banded iron formations span this period of inferred atmosphere transition, eg Mt Goldsworthy, Mt Tom Price, Middleback Ranges. Geological evidence for a reducing Archaean atmosphere is both ambiguous and controversial (see review by Phillips, Law and Myers, 2001). Many earlier ideas (eg no Archaean redbeds; all very large iron ore deposits being post-Archaean) have been disproved by dating, whereas other evidence (eg homogeneous detrital gold grains, inferred palaeosols) has not withstood geological scrutiny. The interpretation of some data sets (eg inferred detrital uraninite and pyrite in some Archaean meta-sedimentary rocks) is still controversial. In fact, some lines of evidence now suggest that oxygen was present in the atmosphere well before 2.5 Ga (eg sulfates in the Pilbara craton, carbon distribution in clastic sedimentary rocks). An oxidising Archaean atmosphere has important implications for the development of iron formations. First, the atmosphere is an obvious potential source of oxygen to stabilise ferric iron minerals. Second, reduced fluids in equilibrium with ferrous iron are commonly inferred to transport iron in solution to the depositional site. The redox state of the atmosphere thus provides critical constraints on the solution chemistry of surface waters, effective transport paths for iron and particularly on viable precipitation mechanisms. Iron formations developed from fluids in equilibrium with the atmosphere also have the potential to provide important constraints on the evolution of EarthÆs early atmosphere. If an oxygenated atmosphere is a necessary condition for the development of iron formations, then the Archaean atmosphere must have been oxidising since at least 3.5 Ga. If the redox state of the atmosphere is not a necessary condition, then the time distribution of iron formations cannot be used to provide constraints on atmospheric evolution. Given these uncertainties, models for the genesis of iron ore deposits of Archaean or early Proterozoic age should not rely on a reducing atmosphere in the absence of independent evidence and the alternative of an oxidising atmosphere should also be considered.

Jan 1, 2002

By P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Consultants in the mining industry have the opportunity to visit interesting deposits all over the world. Each deposit has its own set of challenges to face when it comes to defining and understanding the deposit geology and the economics to make it viable for extraction. Some of the challenges can include appropriate data capture, sampling techniques, structural characteristics, geochemistry, geophysics, lithology definition, and economic boundaries. It is essential that the practices used at each deposit (eg drilling, sampling, geological modelling, resource estimation etc) are documented and the results obtained are robust and defensible. The Competent Person is not always aware of instances where their resource estimation practices have not been substantiated. ‘You don’t know what you don’t know’ is a phrase frequently used during a mineral resource audit. Technical work to substantiate drilling, sampling, density, assaying, geological modelling and estimation processes is not always completed. Audited Competent Persons often comment: • ‘I was unaware that this was required.’ • ‘I have not had training in this area and do not know how to complete the checks required.’ • ‘This is how we’ve always done it.’ Examples of audits where it was found that geological practices were not substantiated are examined here. A discussion is included on why substantiation of these practices is important, and potential reasons as to why there are instances of unsubstantiated processes and practices are discussed.

Mar 22, 2022

By J-P Franzidis, E V. Manl, K Runge

Over recent years a number of techniques have been developed as part of the Australian Minerals Industries Research Association (AMIRA) P9 project to represent mathematically or measure directly subprocesses occurring in flotation cells. These include the determination of a:machine parameter (bubble surface area flux, Sb); froth parameter (froth recovery, Rf); entrainment and drainage parameters; and ore floatability parameter (Pi). A cost-effective methodology was developed for using these techniques to derive models of flotation circuits. This methodology was applied to derive a model of the flotation circuit at the Western Mining Corporation (WMC) Ltd Mt Keith Nickel Concentrator. The model was used to simulate a number of minor circuit flowsheet changes, the results of which are discussed in this paper. One year later, a second study of this plant was conducted. In this second study, data were collected while operating the plant in the flowsheet configurations that were simulated from the model developed from the first study. The results obtained from the second study showed reasonable agreement with the trends predicted from the first study model; discrepancies can be explained in terms of the model assumptions. This suggests that this simple circuit modelling methodology can be useful in assisting plant engineers to optimise flotation circuits.

Jan 1, 2000

By T Davis

Cameco Corporation operates the high-grade 140 tpd fly-in/fly-out underground McArthur River Uranium Mine in Northern Saskatchewan in a joint venture with Cogema Resources Inc. Reserve grade is in excess of 20 per cent U3O8 with current mining grade averaging 16 per cent U3O8. Due to the high radiation potential of the ore, the non-entry mining method of raiseboring was chosen to minimise worker radiation exposure potential. The raisebore and extraction horizons are located in waste rock with the orebody located between horizons. Ore produced by raiseboring is delivered by LHD to an underground SAG mill and is then hydraulically hoisted to surface receiving facilities after underground thickening to 50 per cent solids by weight. Concrete backfilling is utilised. The orebodies at McArthur River are adjacent to water bearing sandstone. Ground freezing is therefore employed to isolate the ore from this water bearing ground. Calcium chloride brine at -35¦C is circulated through a series of cased boreholes to establish freeze walls up to 25 metres in thickness. At 18 000 000 lb of low cost U3O8 production per annum, McArthur River ranks as the worldsÆ largest uranium mine. Over 50 per cent of the workforce resides in this sparsely populated area of Canada with approximately 40 per cent being of aboriginal ancestry. Site operations must cater for winter temperatures as low as -50¦C.

Jan 1, 2002

By J Crosbie, M Lord, R Bitencourt, P Defferrard

The MMG Century mine, which is the largest zinc/lead mine in Australia, began operating in 1999 and ceased mining from the open pit in July 2015, with processing completed in early 2016. Closure plans were developed from 2006, and detailed planning for closure commenced in early 2011 with the appointment of a dedicated closure planning resource. The site will continue to be managed during the active and passive closure phases to complete rehabilitation commitments and demonstrate that closure completion criteria have been achieved.Completion of the mining/processing phase of the project provides an opportunity to reflect on successes, missed opportunities and lessons learnt with respect to planning and execution of mine closure. This paper highlights examples of success at Century and also identifies key learnings and areas for improvement in progressive closure outcomes. Specific examples examine mine planning and execution involving bulk movement of waste rock and construction of permanent waste encapsulation landforms. The paper also provides recommendations for other sites that are planning for closure.Decisions made during the operational phase of the project life can result in a significant increase in closure liability and reduce the likelihood of achieving lease relinquishment. Likewise, it is of paramount importance to assess the consequences and thoroughly understand the risks associated with changes or deferral of closure plans, progressive rehabilitation targets and closure related key performance indicators.CITATION:Lord, M, Bitencourt, R, Crosbie, J and Defferrard, P, 2016. Closure planning lessons Learnt from the Century mine, in Proceedings International Mine Management Conference, pp 207-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By J Safarian, D Hariswijaya

Treating bauxite residue as an alternative source of metals for iron and aluminium industry is an approach to promote circular economy in metal industries. Reduction of metal oxides with H2-based process is an important step on decarbonisation of metal industry. In this study bauxite residue pellets were prepared and were reduced with different H2-H2O gas compositions at different temperatures which yielded with various degrees of reduction. The bauxite residue pellets were made from a mixture of bauxite residue and Ca(OH)2 powders and sintered at 1150°C. Hydrogen reduction was carried out on the oxide pellets using a resistance furnace at elevated temperatures in controlled reduction atmosphere of H2-H2O gas mixtures which resulted in reduction of iron oxides in the pellets. Unreduced and reduced pellets were subsequently heated to 1400°C to study their smelting behaviour using differential thermal analysis (DTA) and thermogravimetric analysis (TGA) technique to investigate the evolution of phases related to slag formation via smelting. Equilibrium module of Factsage™ ver 8.1 was utilised to analyse results of thermal analysis. It was observed that Tricalcium phosphate-β (CaP2O8), Bredigite (Ca7Si4MgO16), Rankinite (Ca3Si2O7), and calcium alumino ferrite (Ca[Al,Fe]6O10) were formed during thermal analysis as intermediate phases. The initial slag formation for sintered and reduced pellets occurred at 900°C which mainly contains calcium and small amount of strontium component. The slag formation rate increases significantly starting from 1100°C when iron oxides started to form initial molten slag phase which then followed by other oxides dissolution in the system. Gas formation was observed at 1180°C and it was found that the gas to be released from unreduced pellets is O2 meanwhile the gas to be released from reduced pellets is SO2 gas. Gas formation rate for both pellets start to increase at 1280°C when the remaining chemically bonded gas start to be released from the system.

Jun 19, 2024

By R Jacobs, J Yeates

"The Stockman base metals project is situated in State Forest in the alpine area of East Gippsland, Victoria, adjacent to a National Park and within the headwaters of a major Ramsar-listed wetland catchment and the Murray-Darling River system. Site topography is steep, and elevated (650 m – 1200 m above sea level), and subject to circa 1 m annual rainfall, with occasional winter snowfall. The project consists of two volcanogenic massive sulfide (VMS) deposits to be mined by underground methods and treated in a 1.0 Mt/a central concentrator to produce copper and zinc concentrates for export over a ten year operational life. New resource projects are rare in Victoria. Recognising the sensitive setting, planning for the Stockman Project, which is now in the advanced permitting stage, has focused on balancing economic, environmental and social outcomes to ensure social licence to operate is secured and can be maintained. This has involved close attention to triple bottom line (TBL) risks and outcomes. Stockman has successfully gained State and Federal approvals via the Environmental Effects Statement process. The process of obtaining these approvals has required close attention to effective stakeholder involvement, and management of a lengthy and difficult approvals process, which is still to be finally concluded. This paper is a case study of the process of that permitting and the issues encountered to date. Key learnings from the experience have included: successful approvals require close attention to much more than just the project and its technical aspects and physical setting – effective stakeholder involvement and endorsement is critical the differing consultation requirements for local, regional and government stakeholders, to design and plan implementation of a project to meet TBL objectives, and to gain social licence to operate within the Victorian approvals process, the need for an effective lead government agency with policy authority dealing with material policy change requiring post-closure financial sureties estimating realistic permitting time and cost during the project evaluation phase. CITATION: Jacobs, R and Yeates, J, 2016. Stockman base metals project – sustainability, social licence to operate and permitting lessons learnt, in Proceedings Project Evaluation 2016, pp 98–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016