Search Documents

By Clarke DS

The igneous intrusions in SE Papua New Guinea are part of a sub-volcanic to plutonic, high-K calc-alkaline to shoshonitic suite. High-K andesitic to dacitic intrusives on Misima and Woodlark Islands, and shoshonitic intrusives in Milne Bay and the eastern Owen Stanley Ranges are related to late Cenozoic andesitic volcanism. Both suites are associated with epithermal Au-Ag deposits and weak porphyry Cu-Au mineralisation. All significant alluvial and lode gold occurrences in the region are spatially related to intrusions. Intrusions in the D'Entrecasteaux Islands and near Mt Suckling are core plutons related to basement doming, and appear to have no association with either volcanism or hydrothermal mineralisation. The core plutons are not petrochemi:ally distinct from the volcano-re:-ed Intrusions.

Jan 1, 1991

In common with general experience in the iron-making industry overseas, Australia has in recent years suffered a deterioration in the physical quality of her iron ores in their suitability as a direct blast furnace feed. The increasing amounts of fines and the more friable nature of lump ore, especially in the ore from the Cockatoo Island deposits in Yampi Sound, Western Australia, have focused attention on problems of ore preparation and agglomeration, particularly sintering.Although very small pilot scale Dwight-Lloyd type sinter machines were operated at the steel-making centres at Newcastle and Port Kembla during World War II, no sizeable capacity was installed, so that ore was charged to the blast furnaces almost entirely unscreened, and the resultant flue dust was stockpiled.Towards the close of the war, the pilot plant at Newcastle was replaced by a small machine, adjacent to the flue dust stockpile, with a rated capacity of some 20 tons per hour. After approximately five months of part-time operation, this plant was closed down in January, 1945. Production was not resumed until December, 1950, when, due to a temporary ore shortage, it was decided to supplement available ore with sinter produced from the large flue dust stocks of about 300,000 tons. In spite of mechanical and process difficulties, inherent to the design of the plant, operation was continued on a two-shift basis, with several shutdowns for extensive overhaul and plant alterations, until September, 1954, when production was put on a three-shift basis. Addition of Yampi ore fines to the sinter machine burden was not commenced...

Jan 1, 1957

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By H Ishikawa, R Halomoan, S Palaniandy

The Karara iron ore project is a magnetite operation consist of open pit mining and concentrator to produce high-grade magnetite concentrate. The concentrator has adopted three stages of comminution, ie fine crushing in the high pressure grinding rolls (HPGR), primary ball milling and fine grinding in the TowerMill plus magnetic separation in between these comminution devices. Since 2014, the concentrator has increased the plant feed rate by 18 per cent. Meanwhile, the ore hardness has increased by 13 per cent to a Bond work index value of 15 kWh/t that led to a coarser flotation feed. Karara Mine has decided to shift the comminution workload from the primary ball mill to the TowerMill circuit by bypassing the 100 µm fine screen in between the ball mill and TowerMill circuits. This action has increased the circuit feed particle size distribution with a top size close to 1 mm. The specific energy consumption of the TowerMill circuit was approximately 3.4 kWh/t, and the circuit product sizes (P80) were ranged between 38 and 45 µm. A joint process improvement exercise was carried out to reduce the circuit product size closer to the magnetite liberation size, ie 35 µm. Among the activities were circuit audit, recommendation for improvement, modelling and simulation, multicomponent analysis, implementation of recommendations and quantification of the improvement. One of the key findings was the density effect of multicomponent minerals in the hydrocyclone. The analysis revealed that the low density coarser gangue minerals were bypassed to the hydrocyclone overflow stream that has resulted in a coarser particle size distribution. Meanwhile, more than 20 per cent of fine (-35 µm) high-density magnetite particles were recycled back to the mill through the hydrocyclone underflow stream and increased the circulating load. Based on these outcomes, several recommendations such as conversion to bottom feed configuration, use of smaller grinding media, high operating hydrocyclone pressure and additional grinding power to the TowerMill circuit were made to improve the overall circuit performances. Karara Mine has prioritised to implement those recommendations that have a minimal financial implication. Full-scale plant trials with bottom feed configuration and 17 mm grinding media were conducted to evaluate its performances. These trials have indicated that the grinding efficiency in the TowerMill was enhanced by 10 – 30 per cent. In May 2017, all the five TowerMills were converted to the bottom feed configuration. This paper discusses the impact of shifting the comminution workload load from the primary ball mills to TowerMill circuit and the performances enhancement of the TowerMill circuit. CITATION:Palaniandy, S, Halomoan, R and Ishikawa, H, 2018. Shifting the comminution workload from the primary ball mill to TowerMill circuit, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 163–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Grigorescu, J H. Hodgkinson, H Alehossein

A new framework that collates and interprets pre-existing data to assess vulnerability and ultimately plan to avoid or minimise flood-related risk to infrastructure, people, downtime, environment and revenue has been developed. The æClimate Related Adaptation from Terrain Evaluation ResultsÆ (CRATER) method tested at a coal mine in Queensland, provides semi-quantitative information to assist decision makers when designating investment for minimising vulnerability of mining operations to climate. Here we present the processes involved in this three-step approach that uses pre-existing spatial data of the mine site and local knowledge to build a set of visual tools to assist decision-making. The first step of the process is performing multi-criteria evaluation (MCE) within a geographic information system (GIS) on ranked natural conditions at the mine, such as elevation, slope, drainage, soil and vegetation, which is performed to identify critical flood areas. Secondly, a fault-tree analysis identifies how impact can occur and what options there are for impact reduction. Finally, a resource assessment of the mineÆs capacity to adapt reduces the adaptation options to those most suited to the mine. The results are confidential, but for the purpose of introducing the methodology, we present simplified results, particularly of steps 2 and 3. CRATER can also be used for future æwhat-ifÆ flooding scenarios to identify the most suitable locations for roads, buildings or other critical infrastructure. The methodology is transferable to any mine, series of mines or locations along the mining value chain that have sufficient data, providing a practical decision-making tool to identify æno-regretsÆ actions that not only could reduce downtime after or during an event, but in some cases may enhance production between extreme events. We now plan to test this method at a broader scale, to encompass more than one mine in the analysis.CITATION:Hodgkinson, J H, Grigorescu, M and Alehossein, H, 2013. Climate Related Adaptation from Terrain Evaluation Results (CRATER) - interpretation of pre-existing data for mine site flood vulnerability and management, in Proceedings Water in Mining 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By V Pfannenstiel

The United States (US) coal mining industry has been working under comprehensive planning, operating and rehabilitation regulatory requirements for nearly 35 years. The public desire for environmental protection during mining and rehabilitation following mining to achieve post-mining land use and sustainability goals has been a major factor and continues to influence the process. Mining companies have evolved operations to achieve outcomes that address the desired goals and regulatory requirements cost-effectively and successfully. Over the 35 year regulatory period, requirements for more diverse topography, specialised revegetation communities, landform stability and assured sustainability have increased and become more complex. These challenges are effectively met by maximising integration of mine planning and operating with the rehabilitation process. Rehabilitation is then implemented in a more timely and efficient manner and with effective results that achieve desired outcomes, commonly with added value. Peabody Energy (Peabody) has taken this approach in its US operations and this paper discusses an integrated approach and illustrates learnings and results with examples from several of its western US operations.CITATION:Pfannenstiel, V, 2012. Integrated planning, mining and rehabilitation for effective results and sustainable land use - A western United States perspective, in Proceedings Life-of-Mine 2012 , pp 219-232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010

The success of smooth blasting essentially depends on geological condition of rock. Also, in the perimeter hole, borehole pressures with light, well-distributed explosive loads are important to minimise overbreak. In order to simulate perimeter holes with scaled model test, the borehole pressure was considered as a factor of scale. Hydraulic oil pressure is applied as borehole pressure instead of using explosives and detonators in order to remove the undesirable effects of detonators in an experimental set-up of just two perimeter holes in a tunnel blast. The borehole pressure on a perimeter hole is nearly reproduced with hydraulic pressure which is generated by non-electric detonators in the hermetical cylinder.

Dec 6, 2010

Upgrading of Indonesia's Bauxite by Washing Method There were eight bauxite samples used in this research, three samples from Kijang contain total SiO2 18.36 - 29.16 per cent, Al2O3 40.12 - 48.36 per cent, Fe2O3 4.27 - 5.13 per cent, one sample from Tayan, contains total SiO2 4.69 per cent, Al2O3 38.95 per cent, and Fe2O3 19.67 per cent, and four samples from Mempawah contain total SiO2 33.5 - 44.8 per cent, Al2O3 29.8 - 35.9 per cent, Fe2O3 7.29 - 9.88 per cent. All of those bauxite ores have not fulfilled the requirement for Bayer process yet; therefore simple up-grading using a rotary drum scrubber is needed. The scrubbing process was carried out with time variable up to 60 minutes with solid percentage applied was 50 per cent and rotary speed was set up 30 rev/min. The bauxite was washed by following steps: scrubbing, screening, drying, and finally it was analysed to show chemical content. The washed bauxite produced has size fraction that is retained on the 1.7 mm of screen opening. The result of the research shows that the higher alumina content of the raw bauxite, the longer washing time is needed moreover the higher quality of the washed bauxite is produced. The highest alumina content of the washed bauxite was 53.67 per cent with the alumina recovery was 89.66 per cent and the concentration ratio of 84.80 per cent was achieved within 20 minutes of washing time of the raw bauxite (Al2O3 48.36 per cent). The washed bauxite resulted from this research is suitable as a raw material for Bayer process.

Sep 13, 2010

By D J. Clark, S Hewson, T Li

Cadia Hill Pit is a gold copper porphyry deposit hosted in monzonite. The pit slope design is primarily based on structural controls related to faults and shears with largely massive rock masses between the structures. The slope design attempts to achieve an optimum configuration at a bench to overall scale, considering economics and safety implications against the geotechnical and structural conditions. To date the slopes have been mined at interramp angles of up to 60¦ over heights of 120 m. Limited slope and batter failures that have occurred are structurally controlled and occur rapidly. The pit-mining schedule requires concurrent mining of part of the final pit walls and the progressive interim cutbacks. Engineering and operational solutions to hazard reduction and risk management issues have been implemented wherever viable to æengineerÆ out the hazard and mitigate the risks. However, comprehensive management plans and operating procedures have also played a vital role. This paper details the management plan and the operating procedures that have been developed and implemented to mitigate the risks associated with rock falls.

Jan 1, 2003

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

By N J. Arunakumaren

A coal mine is proposed for an area where a major river traverses the project area. There were initial concerns that inflow of groundwater from exposures of high permeability alluvium associated with the river system could pose mine dewatering problems together with adverse impacts on surface water resources in the river. The project included collation and analysis of geological and hydrogeological data collected historically over a long period of project investigation and evaluation. The project also included establishment of additional groundwater monitoring points to provide a reliable groundwater contours. The groundwater level contours were produced to allow numerical models to be calibrated to support estimation of groundwater inflow. River bed cross sections were also prepared to assist study of the effect of river flow on the inflow. Two separate MODFLOW groundwater models were produced to simulate long-term groundwater inflow to the mine with an upper model consisting of the Quaternary and Tertiary alluvium lumped together and a lower, separate model consisting of Mesozoic coal measures. Analytical solutions were used to predict initial inflow from the alluvium and from the coal measures.

Jan 1, 2003

By M Kuruppu

Large mining operations require a high percentage of the capital invested in mobile and fixed mining machinery. From an investment point of view this expenditure must be met by an equally high rate of return, thus the need for high plant and equipment reliability is of major importance. Equipment downtime is undesirable and very costly, resulting in lost production and revenue, which is of critical importance to successful mining operations. One of the solutions to this problem may be found in the form of competent computerised maintenance management software systems, which help to reduce the problem of breakdowns. These software assist the engineers for the management of service orders, resource allocation, progress monitoring as well as costing. They also facilitate the communication of targets and objectives among the service personnel. A computerised maintenance management software called MAINPAC was used to record and plan the activities of mobile equipment maintenance in a large mining operation in Western Australia. Among the details recorded were equipment data, service history, machine downtimes, previous maintenance, job planning and the resource required. This information further helped to analyse the maintenance efficiency, availability and the reliability of the equipment.

Jan 1, 2006

By Mitchell I, Gelfi P, Dunne R, Pyper R

Dump leaching at Teller in its present form began in the fourth quarter of 1988 as an adjunct to milling operations. Initial plans called for a dedicated dump leach facility capable of processing ore at an annual rate of 2.0 million tonnes. Construction of a dump leach pad, collection and process ponds, carbon adsorption system, elution plant as well as reagent addition and ancillary facilities was initiated in mid-1988. During the course of construction, additional reserves were proven. As a result, design throughput was increased to 4.0 Mtpa. Leach pad capacity and solution supply systems were upgraded to handle the larger throughput. However, the carbon adsorption/elution facilities were not upgraded due to space limitations. During 1990 it was decided to expand the dump leach operation to 6.0 Mtpa. Construction of a second leach pad was required which was initiated in early-1991. Plans were again upgraded prior to completion to a target annual throughput of 10.0 million tonnes was. A further two leach pads have been constructed. The first of these being completed during the latter part of 1992. Construction of the latest and largest pad commenced early in 1994.

Jan 1, 1994

By Gonzalez-Dominguez J. A, Dreisinger D. B

At Cominco's Zinc Refinery at Trail, British Columbia impurities are removed from zinc sulphate electrolyte by a two-stage purification process using zinc dust. Copper, cadmium and thallium are removed in the first stage whereas cobalt is removed in the second stage. Cobalt removal kinetics are affected by soluble antimony and copper additions to the electrolyte. This study was focused on the kinetics of cobalt removal by zinc powder cementation. Experimental variables included copper and antimony concentrations, pH and temperature. Common organic additives employed in zinc plants were studied to determine potential interactions with the cobalt removal process. Cementation products obtained from laboratory experiments and plant practice were studied using SEM. A number of significant results were obtained: 1. Copper and antimony ions were sustantially removed from solution during the early stages of the cementation reaction (within the first 15 minutes). Cobalt cementation kinetics are slow and follow a first order kinetic regime. 2. A drop in the cobalt removal rates can be correlated with a rise in the Eh of the slurry. 3. Ligninsulphonate, Percol 351 and animal glue at levels of 2 mg/L significantly impede cobalt cementation.

Jan 1, 1993

By H Ishikawa, H Zhou, M Spagnolo, R Halomoan, S Palaniandy

The Karara Mine concentrator commenced operation in November 2012 to produce high-grade magnetite concentrate. The circuit consists of three stages of comminution plus magnetic separation at each stage for early gangue rejection. High-Pressure Grinding Rolls (HPGRs) are used for fine crushing, followed by ball mills and TowerMills in secondary and fine grinding duties respectively. In recent times, the plant throughput rate has had to exceed design by 18% to maintain the targeted concentrate productivity. Meanwhile, the ore hardness has increased by 25% to 15 kWh/t, leading to changes in the circuit operation and design. These changes led to coarser and harder feed to the TowerMill circuit that affects the subsequent separation processes. Nippon Eirich (the TowerMill manufacturer) has partnered with Karara Mining Limited (Karara) to optimise the TowerMill circuit operation to achieve a circuit product with an 80% passing (P80) of 35 µm. Several activities, including a TowerMill circuit audit and performance evaluation, multi-component analysis, modelling and simulation, were carried out as part of the optimisation exercise. The circuit audit results revealed that the TowerMill circuit feed size F80 had increased and ranged from 67–75 µm. The circuit product P80 ranged between 42–55 µm. The average circuit specific energy was 3.4 kWh/t. Moreover, the differences in density between magnetite and gangue minerals had affected the hydrocyclone performance where the efficiency curve exhibits coarse end deflection indicating that low-density coarse material was bypassing to the overflow stream. A multi-component analysis was carried out to further investigate the coarse end deflection of the hydrocyclone efficiency curve. The analysis showed that the magnetite and gangue minerals had different cut sizes of 32 and 64 µm respectively. Furthermore, 33% of the magnetite (below 35 µm) was being recycled back to the mill due to the density effect. Based on these findings, several recommendations for process improvement were identified and implemented including:• converting to a bottom feeding configuration to improve the grinding efficiency in the mill• additional grinding power in the fine grinding duty to compensate for the increase in plant throughput and ore hardness• improved classification efficiency by converting to smaller size hydrocyclones. Simulation studies carried out to evaluate the impact of these implementations had indicated that a P80 close to 35 µm with a steeper size distribution could be achieved by using the bottom feed configuration with additional grinding power. The TowerMill circuit was converted to bottom feed configuration and the performance was evaluated. The operating work index, size specific energy and circulating load were 30% lower than the top feed configuration, indicating that the bottom feed configuration had a higher grinding efficiency. This paper discusses the outcome of the circuit audit, multicomponent analysis, circuit simulations, improvement strategies and quantification of the improvements. CITATION:Palaniandy, S, Spagnolo, M, Halomoan, R, Zhou, H and Ishikawa, H, 2017. Fine grinding circuit process improvement at the Karara mine concentrator, in Proceedings MetPlant 2017, pp 101–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

In 1987 the control strategies at the then ZC Mines' New Broken Hill Consolidated concentrator were a miscellaneous mixture of computer hardware and technology for ISA, grinding and residue thickener control. Field instrumentation was based on current-to-air technology of approximately the 1960s. Decisions were made to rationalise computer and field instrumentation technologies; the object being to consolidate control loops into one system to enable expansion of the system to include all facets of plant operation. The first stage was to install a DEC Micro PDP 11/23 computer and serial line communication as recommended by AMDEL Ltd, for the ISA system, as discussed by Walsh and Freeman (1988). The second stage was to select and install a distributed control system for the centralisation of the control loops into one system, and to replace field instrumentation with state-of-the-art technology. This paper deals with the second stage of the rationalisation, in an attempt to give an insight into what is required when personnel are faced with such a decision, details of costs involved in keeping a system functioning and utilised; and the requirement to train personnel for acceptance of further control strategies.

Jan 1, 1991

By Q-c Li, G-l Gao

Cyanided tailings produced by gold processing operations may cause environmental problems, because they contain pollutants such as arsenic, sulfur and cyanide compounds. Moreover, tailings containing economic metals such as Au, Ag, Cu, Pb and Zn, are potentially valuable resources. In this article, cyanided tailings are catalytically oxidised by nitric acid in the presence of air or oxygen. The resulting solids may be leached to recover Au and Ag. The solution can be used to prepare ferric sulfate or iron pigment. Gases released in the reactions were recycled and reused by oxidation and absorption. All of these greatly improve metal recovery and the reuse prospects of cyanided tailings. Under the following conditions where the initial temperature of oxidation is 80¦C; initial concentration of nitric acid is 30 per cent (by weight); feed proportion (nitric acid to cyanide tailings mass ratio) is 3:1 and reaction time is two hours, the conversion ratio of cyanided tailings is 90.06 per cent. At the same time pyrite in the cyanided tailings is oxidised effectively, gold recovery is as high as 92.3 per cent and nitric acid loss per cycle is only five per cent because of NOx recovery.

Jan 1, 2007

Traditionally, the term ætotal systemÆ design applied to comminution conjures images of a design that addresses the usual business and operational drivers, including health, safety and environment (HSE), capital cost, operating cost, throughput and product size. In terms of the physical process, the mine to customer type studies also exemplifies an approach that satisfies a normal ætotal systemsÆ approach. As an industry there are drivers that are forcing a re-consideration of what we regard as our total system. This modification of drivers will require changes in approach and implementation to provide the best solutions. Some of the major changes that impact the drivers are shortage of skilled personnel, changing social attitudes to remote mine site work, greenhouse gas emissions (GHGE), quality of available orebodies and geographical location of new mine sites. One approach to the challenges presented by the changing business environment is to expand the system envelope around comminution to ensure that comminution, in its widest sense, helps to meet the new realities. Background to the new drivers and constraints is provided and some of the appropriate responses are examined in relation to the impact on the total system.

Jan 1, 2007