Search Documents

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

By R Pinksen

The Iron Ore Company (IOC) of Canada Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1 m × 1 m × 1 m) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion into the blastholes provided more resistance to the forces created by dynamic water and reduced the infi ltration of the emulsion into the cracks and fissures of the rock mass. Blast results showed reduced amounts of oversize and more consistent fragmentation throughout the muck piles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realised.To determine the effectiveness of the oversize reduction project, IOC used shovel based camera technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with global positioning system (GPS) locations. A large population of digital images was analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jul 11, 2011

The BHP Billiton Cannington Mine uses paste as the principal method of backfill. The paste consists of mine tailings and cement. The pastefill process at Cannington includes a surface plant where the thickened total tailings stream is filtered using two vacuum disc filters operating in parallel. The filter cake is mixed with Portland cement in a spiral mixer to produce a paste at a specified yield stress and cement content. The initial system design only required paste to be delivered under gravity. In July 2001, Cannington Mine expanded to 1.8 million tonnes per annum. In order to achieve this, production commenced on five new levels underground, 350 metres horizontally from the paste plant. Due to the high viscosity of paste, this distance was too far to transport by gravity. Traditionally, paste has been transported only short distances (50 m) using positive displacement pumps, with very limited success. At Cannington, a conveyor was installed which was designed to achieve zero spillage into the environment. This paper discusses the innovative design strategies used to attain zero harm on the environment whilst conveying a material, which is difficult to transport.

Jan 1, 2002

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By J Tibbett, F T. Suorineni, B Hebblewhite

Block caving is an important mining method for the future economic exploitation of large, low-grade, steeply dipping orebodies. While block caving is not a new method, there are still many unknowns surrounding the mechanics driving the process, particularly as we are forced into deeper, higher-stressed and stronger ore deposits. The caving industry is desperate to provide some explanation behind the myths of caving geomechanics to better predict and manage current caves and caves of the future. Large amounts of data are collected to help understand caving, but it is not fully utilised and current approaches for analysing the data are capacity limited. The application of virtual reality and scientific visualisation (VRSV) technology to visualise and analyse block caving is a critical future component in the assessment toolbox. VRSV enables large, complex, multidimensional data sets to be analysed and the power of human visual problem solving processes to be utilised. Block caving is a complex system and needs to be analysed as a system, rather than looking at individual factors one at a time. A software module has been developed at UNSW Australia for use in the advanced visualisation interactive environment for analysis of the block cave mining system (BCMS). This fully immersive, 3D virtual assessment tool shows exciting potential and is used to analyse the BCMS with a close linkage to time (ie the chronological occurrence of data). This tool will enable a true investigation into the cause and effect relations within the BCMS. Current research is investigating Newcrest Mining Limited’s Ridgeway Deeps operation and is aiming to turn some of the cause/effect relationships into increased geomechanics understanding to provide improvements to ground control management. This paper outlines the methods of assessment used to analyse BCMS geomechanics with VRSV and shows the potential of the software module for BCMS analysis.CITATION:Tibbett, J, Suorineni, F T and Hebblewhite, B, 2014. The application of virtual reality technology and scientific visualisation to the understanding of block cave mining systems, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 195–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By M Hawkes, Z Ji Gang, Z Ming, R Hassell

As underground mines become more geotechnically challenging with increasing depth and excavation size, the requirement for ground support to be installed as per design becomes more critical. The verification of installation quality for cable bolts and grouted rock bolts is difficult to assess. Current methods to control quality have limitations; pull testing is largely inconclusive with only extremely poor installation being identifiable. Audits during installation can only capture a small percentage of installed bolts. Following large rock mass displacement from either squeezing ground or seismic events, even previously well installed bolts may have yielded and require replacement. A method to provide an improved understanding of the reinforcement installation quality is Non- Destructive Testing (NDT) using acoustic reflection. To validate the accuracy of an NDT system, both plain and bulbed strand cable bolts were grouted in clear plastic tubes. The encapsulation grout quality was deliberately varied from full encapsulation through to partial encapsulation and a range of different size voids. The clear tubes allowed the ground encapsulation to be observed. Cable bolts strands were cut at varying lengths and different water cement grout ratios were used. Acoustic testing of the cable bolt specimens was completed blind; the technicians were not aware of what was being tested. The NDT results correlated well with the grout encapsulation, with differences between full encapsulation, minor voids and major voids being determined. The different water cement ratio and bolt lengths (including when partially cut) were also identifiable but with some discrepancies. Trials of the technology underground have also shown the data collection process to be relatively quick with each bolt taking 1-2 minutes to test, with interpretation of the results able to be completed soon after. The NDT results collected from the underground trial showed a wide variance in cable bolt grout encapsulation quality indicating that there were installation issues.

Mar 15, 2021

Stawell Gold Mines Pty Ltd operates two underground decline mines within the township of Stawell. An active exploration program and commitment by owners to improving the ore reserves has led to an improved mine life and reduced operating costs since the purchase of the operation by Mining Project Investors and Pittston Mineral Ventures in late-1992. Over the past six years of operation a cumulative 1 150 000 ounces of gold have been added to the mineral inventory. An improved geological understanding of the orebody has evolved over time increasing the ore reserves and allowing the development of long-term plans for the mines future. This has enabled important capital decisions to be made providing the impetus for improved productivity and thereby reduced operating costs. Co-operative mine planning and mine geology utilising best practice geological systems have enabled the effective extraction of a structurally complex and mineralogically varied deposit within a rural Victorian township. Detailed metallurgical research has improved the function of an aged and poorly designed circuit to boost the mill capacity whilst also improving the metallurgical recovery. The combination of metallurgical expertise and an understanding of the geological setting enable an effective control of metallurgical recovery.

Jan 1, 2000

As the chief field of the gold dredging industry in Otago is the district traversed by the Molyneux River (called above Cromwell the Clutha) and its tributaries, a brief reference to the geology of that region and the origin of its alluvial gold will not be out of place. The prevailing rocks are metamorphic schists, chiefly mica and quartz schists, pr.obably of Silurian age. Though these rocks do not contain many payable quartz reefs, gold appears to be distributed in small quantities all through them,chiefly associated with the quartz lamime and lenses. The river drift, however, contains numerous pebbles of quartzite, quartzoze conglomerate, and fme-grained slate. Seeing that these rocks are hardly known to occur in situ within the watershedof the Molyneux River, though Devonian and carboniferous rocks of similar character occur to the north-east and south-west, it seems probable that the schists were at one time overlaid by carboniferous and Devonian rocks, and that these have been removed by denuding agencies. Be this as it may, it is certain that the schists themselves have been greatly eroded by the action both of water and of ice, and that the resulting drifts have themselves, in many cases, been sorted and re-assorted by the same agents.Consequently the drifts are very varied in character and often developed on a grand scale. In geological age they vary from Early Tertiary (though some may be older) to Recent.

Jan 1, 1903

East Otago gold deposits are hosted in Otago Schist that is the metamorphosed equivalent of Permian-Triassic Torlesse terrane greywackes. Relatively undeformed Torlesse sequences in Canterbury have <l m - 50 m bedding, with c. 500 m - l km and c. three kilometre scale units, typically either: 1) thick-bedded, massive, sandstones; 2) thin-bedded sandstone-argillite flysch; or 3) siltstone- or argillite-dominated units. Such lithological layering in Otago was intensely folded, deformed, and overprinted by metamorphic fabrics during Jurassic-Cretaceous regional metamorphism. Although primary sedimentary structures can no longer be recognised, a æghostÆ lithological variation is still present in Otago represented by psammitic (sand-derived), interlayered (sandstone-siltstone derived) and pelitic (siltstone-mudstone derived) schist. Lithological æunitsÆ in the schist are typically either 20 100 m or c.1 - 2 km thick, and are oblique to faults and shears hosting gold mineralisation at Macraes, Barewood, Nenthom, and Oturehua. Lithological variations and folds in lithological units are important in the along-strike distribution of gold in these deposits, and in the development of relatively high-grade pods and shoots at l00 m - 1.5 km scales. Ramps, flats and step-overs (known to be locally important for controlling mineralisation) are commonly located at lithological boundaries, presumably by local refraction of faults or shear zones as they propagated through folded stratigraphy. The various lithologies have also responded differently to deformation, causing variations in permeability that affected the penetration of mineralising fluids. Mapping lithological variations in barren host-rocks, either directly+ by fieldwork or indirectly by aerial geophysics, is a key to understanding and predicting the distribution of gold at mine and deposit scales.

Jan 1, 2001

The underground storage of LPG and other hydrocarbons is in current commercial use in Northern Hemisphere countries in Europe, Asia and the USA.Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, embarked on a worldwide feasibility investigation in 1989 to establish the viability of constructing an underground LPG storage facility in Sydney, Australia, the first of its kind in the country. Elgas recognised that with the limited 19 000 tonnes of storage capacity at Port Botany and the limitations imposed by use of small coastal ships (up to 10 000 tonnes capacity), a larger storage facility was required to utilise higher capacity ships from more remote sources such as the North West shelf and overseas. This would achieve security of supply in high demand periods and economies of scale. The underground option also provides improvements to safety and environmental standards.

Jan 1, 1999

By T Laing, M A. Abdalla, P Hagan

Open pit operators are facing a number of challenges in the area of blasting and blasting processes, such as wall control, quality of fragmentation, explosives consumption and vibration. Remaining financially viable is one of the most significant objectives for mining professionals as they work through the blasting challenges within the mining chain of processes. This objective is such a significant challenge, primarily due to the high consumption of materials and the direct consequences on the downstream processes in the mining work flow, including loading, hauling, crushing, milling and mineral concentration. This paper reviews and discusses a technique to achieve this objective, namely air-decking. The performance in a number of mines around the world is reviewed focusing on the economic contributions of air-deck blasting. Various scenarios are investigated and simulated, covering both conventional and air-deck blasting, using JKSimblast software. The scenarios explore a range of issues and found that optimum results could be achieved with a minimum amount of explosives. The results obtained from the simulations were verified with blasts at Rixs Creek Coal Mine, Australia. Based on the verification results the simulations were then modified to more accurately model the actual conditions and parameters on site and to ensure that the models derived meet the production and control requirements at the mine site. Ultimately, overall analysis and comparisons were applied to the outcomes of the conventional and air-decking blasts revealing a reduction in material consumption of around 25 per cent with consequential savings and up to a 30 per cent reduction in ground vibration.CITATION:Abdalla, M A, Laing, T and Hagan, P, 2012. The contribution of air-deck blasting to open pit mining economics, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 7-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By C Slaughter, J C. Tien

Commonly held ideas about effective training have long emphasised the importance of realism. Realistic training builds better experience among the trainees and a better perspective on the training material, making training more effective. While great strides have been made in this realm for mine safety and mine rescue training there are still areas that can be improved. One possible area is the expanded use of a mine fire simulation program where the migration of gases and smoke can be realistically displayed in an emergency, and outcomes varied as different conditions are being simulated. The use of mine fire simulation software potentially allows for the creation of more realistic scenarios in that smoke advance rates can be measured and recreated in evacuation scenarios, or that gas readings in mine rescue training can be dynamically and realistically changed to show the effect that time has on the fire scenario.CITATION:Slaughter, C and Tien, J C, 2015. The potential use of mine fire simulation software as an enhancement for mine safety and mine rescue training, in Proceedings The Australian Mine Ventilation Conference, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By K A. Heasley

The LaModel program was initially developed in 1993, and it is used to model the stresses and displacements in thin tabular deposits such as coal seams. It uses the displacement-discontinuity variation of the boundary-element method with a simplified laminated overburden model and because of this formulation, it is able to quickly and effectively analyse large areas of single- or multiple-seam mines. Over the last couple of decades, LaModel has been used by many mine engineers and researchers for improving pillar designs and mine safety, and it has been continually updated to add functionality and improve its ease of use and accuracy. The present LaModel can calculate seam displacements and overburden, multiple-seam and total seam stresses, pillar safety factors, energy values, roof-bending stresses, fault effects and surface subsidence. It can automatically generate the mine and overburden grids from AutoCAD drawings, and it includes wizards for automatically generating Bieniawski strength coal pillars, easily calibrating the overburden properties to observed abutment stresses and calibrating the gob material to expected gob loading. This paper will present the formulation and features of the modern LaModel program and demonstrate its utility with a multiple-seam case study from the rugged topography in Southern Appalachia.CITATION:Heasley, K A, 2014. LaModel – a program for coalmine modelling, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 409–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By L Snyman, S Webster and J Samosir

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant, which produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment and recover the ore.The E48 extraction level is located approximately 581 m below surface and consists of ten extraction drives and 214 drawpoints. Several stress measurements carried out at various levels in both E26 and E48 indicated a low underground regional stress environment and a low to moderate stress state in the E48 orebody. The E48 block used a post undercut strategy that was initiated in 2009, with production commencing in September 2010 and cave-through to the surface occurring approximately four months later in January 2011. Changes to the cut-off grade and fixed prices meant that Northparkes was able to develop an additional two drives to the north of the existing cave and one additional drive to the south. Modelling of the cavability of the additional drives indicated that the cave would not readily propagate to sufficient height of draw to mobilise the ore and tended to arch over to the existing cave shape. Based on modelling and a desire to reduce the risk of the project, preconditioning was adopted. Along with the requirement of safely hydrofracturing an active cave, a measure of the success of the preconditioning was desired. Few block cave operations have developed extension drives adjacent to existing caves.This paper summarises the lessons learnt from the development of this extension project, with a specific focus on ground control and monitoring.CITATION:Snyman, L, Webster, S and Samosir, J, 2016. E48 cave extension at Northparkes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T Clemens, D Trumm

Adopting environmentally acceptable practices in New Zealand is a crucial requirement for mineral wealth development. Recent planned expansions in the coal and gold industry have increasingly placed mining in the media spotlight. A lack of appropriate standard environmental guidelines has resulted in inconsistent responses and assessments of current and proposed mines. These inconsistencies have lead to delays in decisions on developing economic mineral deposits that may have only minor short-term impacts, and have also allowed unacceptable environmental management practices to continue elsewhere. A research collaboration between CRL Energy, Landcare Research, University of Canterbury and University of Otago aims to provide regulator groups and the mining industry with a unified approach to the requirements of the Resource Management Act 1991,the legislation that largely drives the nationÆs environmental policies and guidelines. The tangible outcome of this research program will be water quality and impact management guidelines integrated into a decision-making framework. The result of this unification will assist in the development of viable mineral deposits and minimise environmental impacts. The framework will be derived from a synthesis of three objectives. Objective 1 identifies potential water quality impact. This objective is based on a targeted geochemical study of the lithology and waterways of the West Coast and Southland regions. Objective 2 categorises the degree of impacts on the ecology of receiving aquatic ecosystems and determines the processes that drive aquatic ecosystem recovery. Objective 3 identifies best strategies to sufficiently manage impacted ecosystems, and to prevent future unacceptable impacts. Wide consultation with representatives of the mining industry and regulator groups will occur frequently during the development stages of the framework. It is anticipated that this multidisciplinary approach will provide a robust and coherent, standardised system that will assist in achieving industry and environmental targets.

Jan 1, 2004

By R Dwyer

Iron ore currently mined in Australia generally requires very little beneficiation. However, depleting high-grade resources means that in the future low-grade iron ore deposits will need to be mined to meet the increasing demands of the global steel industry. Along with the increased demand, the industry faces additional pressure to reduce the environmental impact of mining and mineral processing. This has stimulated research beyond incremental improvements to conventional processing into alternative low-impact processes, including biotechnological approaches to mineral processing.Bioflotation and bioflocculation have emerged as relatively recent technologies, in which bacteria and/or their extracellular material may be used as flotation reagents (collectors or modifiers), enabling improved selective separation of minerals. The primary advantage is the production of a selective, environmentally-benign alternative to conventional flotation reagents. A biotechnological approach may also be taken in the beneficiation of high-phosphorous iron ores utilising bacteria capable of iron reduction and phosphorous solubilisation.Samples from three iron ore deposits in Western Australia were examined for bacteria suitable for iron ore benefi ciation. A number of common soil microorganisms including Pseudomonas spp, Limnobacter thiooxidans, Paenibacillus spp, and Ralstonia insidiosa were identified using culture-independent molecular techniques. A number of anaerobic species belonging to the genus Clostridium were also identified in the core samples. Selected aerobic species were enriched and isolated on high nutrient media in the presence of haematite. Several of the isolated strains showed an affinity for iron ore, attaching to haematite in enrichment cultures and further demonstrated through adhesion studies. Other isolated species such as Ralstonia isidiosa and Pseudomonas stutzeri are known to solubilise rock phosphates in soils and have potential for the removal of phosphorous from Australian iron ores.

Jul 11, 2011

Salaries for mining professionals have gone up substantially in the last two years across most vocations and there has never been a better time to enter the industry, in terms of career opportunities and salary packages. With so many offers on the table and companies outbidding each other to attract the best talent, many new professionals are being lured in by the big money, sometimes at the expense of a satisfying career and a sustainable lifestyle. What should we consider when accepting a new position? What are our values, and how do these drive our decision making? This paper examines our core values as people and makes some observations about what it takes to really succeed in the mining industry.

Jan 1, 2006

By S Oliver, D Willingham

"Although a resource model is central to the mineral resource value estimation process (Glacken and Snowden, 2001), creating it is a labour intensive task and in the end it is a limited representation of the actual orebody. Creating this resource model is a labour intensive task that requires inputs from geology, mining, metallurgical and commercial disciplines. It requires thousands of samples from hundreds of drill holes to be verified, grouped in geological domain, interpolated and then valued. Even after all this effort, a model is only an estimation; therefore further significant effort has gone into quantifying uncertainty in the model and subsequently risk around any value estimates derived from the model. Further risks to model quality are introduced through poorly conditioned data or incorrect assumptions.This paper proposes the application of machine learning to automate the resource model development. Machine learning is applied to the traditionally manual tasks of geological formation, domain identification and validation of the block model mineralogy. Through automation the resource estimation process can be accelerated, allowing more drill holes or a larger resource body to be processed in a given time frame, or allowing the process to be more agile to changes in input data and assumptions. A case study based on drill hole data from a Western Australian iron ore deposit (Government of Western Australia, Department of Mines and Petroleum, 2015) is used to demonstrate the application of machine learning in this process.CITATION:Oliver, S and Willingham, D, 2016. Maximise Orebody Value through the Automation of Resource Model Development Using Machine Learning, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 295–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007