Search Documents

By Menne DM

The carbon-in-pulp (CIp)process has become well accepted and firmly established in the gold industry of South Africa and, at this stage, six large CIP plants are treating close to I million metric tons of material per month. Many small operators are also using CIP and additional large plants are either nearing completion, are on the drawing boards,. or are being considered. The programme of testwork that preceded the acceptance of the CIP process in South Africa was conducted over some eight years and has been previously described'-7. With the start-up of the President Brand CIP plant on 'calcine' in July 1980 and that of the Western Areas CIP plant on repulped filter residues in September 1980, the emphasis on the CIP process switched from pilot plants to these large plants - and has largely remained there. As it has started up, each new CIP plant benefited from the experience gained and the developments made, on earlier plants but, since so few plants have so far been established in South Africa, each new plant and each new design has revealed a further set of conditions to be met and problems to be overcome. However, in the highly collaborative atmosphere of the South African gold-mining industry, the results and observations from the operation of these first plants were shared by all mining groups. This paper will attempt to describe typical developments on, and results obtained from, these new large plants, and will incorporate significant results from the earlier laboratory and pilot-plant investigations.,

Jan 1, 1982

By Orr D. B

This is a case history of prospec- ting carried out by Comstaff Pty. Ltd. over the Pinnacles Area, part 4 of Exploration Licence 5/63, 9 km north of Rosebery in Western Tasmania. Evidence is presented to show that A 0 soil samp ling is a viable prospecting method for outlining polymetallic sulphide occur- rences in areas where leached organic/ glacial soils are common. Diamond drilling of low threshold anomalies has intersected base metal mineralisation.

Jan 1, 1977

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By Scholl EW, Ricken W

The simultaneous presence of fuel, oxygen, and of an ignition source is necessary for an explosion to arise. If one of these conditions is missing an explosion cannot take place. A continuous reduction of oxygen, often applied as a protective measure in surface plants, is not to be considered for underground mining because of possible danger to persons. Therefore, measures for avoiding explosions can only be concerned with lowering methane and coal-dust concentrations to an undangerous level and avoiding ignition sources. As these measures alone are not sufficient, additional ones have to be taken to keep the effect of an explosion as low as possible. Measures for controlling and monitoring methane are essential. Although the formation of dangerous coal dust concentration cannot be avoided it can be reduced. Dust-binding by means of hygroscopic pastes and dusting with limestone dust are effective measures to pre vent explosions.

Jan 1, 1981

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By T Trott, M Lewis, G Lumley

The analysis of equipment trends in The AusIMMÆs revision of Monograph 19 - Australasian Mining and Metallurgical Operating Practices (AMMOP) (in prep) in the paper by Graham Lumley raised some interesting, and in parts disturbing, trends in the Australian open cut mining industry. According to the Australian Bureau of Statistics (2011) the productivity of the whole mining industry is down by 34 per cent since 2001. In terms of open cut equipment, median output for draglines is down by 15 per cent since 2003, electric rope shovels are down by 41 per cent since 2003, hydraulic excavators are down by 39 per cent since 2008, front-end loaders are down by 39 per cent since 2007 and trucks are down by 41 per cent since 2006. Clearly e boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top ten per cent by annual output per unit of input) has declined, but not by as much as the median (eg shovels down by eight per cent, excavators down by 19 per cent and FELs down by five per cent). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins, pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one, will be crucial to reversing the decline in open cut equipment performance.CITATION:Lumley, G, Trott, T and Lewis, M, 2012. Reversing the trend in open pit mining equipment output, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 75-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By S Long, D Carnovale, L Louwrens

The Mt Wright underground mine (MTW) is located near the town of Ravenswood in north Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited.The Mt Wright mine has gone through many stages, from the conception and implementation of the world first ‘sub-level shrinkage’ stoping (SLS) with continuous fill mining method in 2010, through to steady state production. These have been outlined in detail in papers presented by Mackay (2011) and Mackay, Long and Koen (2014) at previous Underground Operators Conferences.Since the last paper was presented, MTW has experienced significant change in two key areas.The first significant change was the discovery of a previously unknown hazard in the form of flat rilling events (FREs) from closed drawpoints (DPs). These events are believed to be unique to MTW and pose a significant risk to both the safety of personnel and the business as a whole. The paper will discuss this hazard and the evolution of the controls and practices that have been introduced to mitigate the risk posed by the identified hazards. The material involved in these events is extremely dry, fine and hot.The second significant change is an altered stress regime bought on in part by a change in the production front orientation and a general deterioration in ground conditions in some areas of the mine. This has caused some production interruptions at MTW. The second half of the paper will describe the challenges encountered, the mechanisms behind these challenges and the strategies implemented to safely return MTW production to planned levels.It is believed that other operations can learn from the issues mentioned above, and the paper has been written with this in mind.`CITATION:Long, S, Carnovale, D and Louwrens, L, 2017. Mt Wright – managing unique risks, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

BHP-Utah Coal Limited operates 33 draglines of varying sizes in the Bowen Basin of Central Queensland. The group's operations with draglines commenced in 1963 with the establishment of opencut operations at the then TPM Moura Mine and continued through expansion of that mine, the commissioning of the Utah Development Company Blackwater Mine in 1968, and the subsequent establishment of six (6) other large opencut mines, all in the general area over the next fourteen years. These operations generally commenced with boxcuts on the sub-crop at depths of 15 to 25 metres. Over the years, depths have increased so that average depths now are in the 45 to 50m range. It was soon realised that dragline operations would have to be supplemented with additional stripping equipment. In 1981, a symposium "45m and Beyond" was held in Rockhampton to assess the problems associated with such "deep" stripping. Subsequently, dragline operations have continued and although addi- tional stripping capacity has been added, in many instances, draglines have been used and are being used to dig depths greater than 45m, some- times as much as 65 to 70m.

Jan 1, 1989

By B Laidens, D Souza, W Bielefeldt

The CaO-MgO-SiO2-Al2O3 system, characterised by its intricate phases and thermodynamic properties, plays a pivotal role in steel secondary refining processes, encompassing desulfurisation, non-metallic inclusion capture, and refractory protection. Accurate predictions for diverse industrial applications, including metallurgy, ceramics, and materials science, are imperative. To address this challenge, a combination of machine learning techniques will be specifically applied to model the liquid fraction of the slag and the solid fraction of MgO. The development of an artificial intelligence (AI) system, leveraging various machine learning techniques, has gained momentum in this project. The focus of this work is on constructing an AI model, based on machine learning techniques, within the CaO-MgO-SiO2-Al2O3 system, utilising simulation results from FactSage™, version 8.1 (by GTT Technologies). The primary objective is to train the AI model using these simulation outputs to predict the percentage of liquid fraction and MgO saturation based on chemical composition parameters. The AI model will undergo training with a comprehensive data set of simulations within the CaOMgO- SiO2-Al2O3 system, covering a diverse range of compositional at 1873 K. These simulations, conducted through FactSage™ 8.1 software, provide a robust foundation for AI model training, ensuring generalisability and precise predictions for the liquid fraction of the slag and the solid fraction of MgO, the solid fraction of MgO in this case is determined by the difference between the total MgO and the MgO in the liquid fraction, so it is not the objective of this study to determine which phase of MgO is in the solid state.. The predictive capabilities of this AI model hold significant implications for process optimisation, quality control, and decision-making in CaO-MgO-SiO2-Al2O3- dependent industries. Precise estimations of the liquid fraction and MgO saturation empower researchers and engineers to enhance operational efficiency and quality. This paper explores the methodologies employed for AI model creation and training, achieved results in terms of prediction accuracy, and potential applications in the field. The development of this AI system signifies a notable advancement in utilising machine learning for better comprehension and control of complex chemical systems. Furthermore, to align the study with real-world steel production, we introduce FeO and MnO at concentrations of 2 per cent and 1 per cent at 1873 K, respectively, following the validation of model results using the CaO-MgO-SiO2-Al2O3 system. This adjustment aims to bring the study closer to the observed reality in steel mills globally.

Jun 19, 2024

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E Donskoi

In order to develop downstream processing routines for iron ore and to understand the behaviour of the ore during such processing, extensive mineralogical characterisation is required. To determine mineral associations, mineral liberation and grain size distribution, imaging techniques have to be used. There are two main imaging techniques used for the characterisation of iron ore, ie, Optical Image Analysis (OIA) and Scanning Electron Microscopy (SEM). In this article a QEMSCANTM system is used as an example of SEM methodology and results obtained from it are compared against results obtained by the CSIRO ‘Recognition3/Mineral3’ OIA system.Both OIA and QEMSCANTM systems have advantages and drawbacks. Even though the latest QEMSCANTM systems can distinguish between major iron oxides and oxyhydroxides, it is still problematic for QEMSCANTM to distinguish between iron ore minerals very close in oxygen content, eg haematite and hydroheamatite, or between different types of vitreous goethite.QEMSCANTM also can misidentify minerals with close chemical composition, ie haematite as magnetite and vitreous goethite as haematite. In OIA, iron minerals with slight differences in their oxidation or hydration state are more easily and directly recognisable by correlation with their reflectivity. In both methods, the presence of microporosity can result in some misidentification, but in SEM methods misidentifi cations due to microporosity can be critical. Low resolution during QEMSCANTM analysis can significantly affect the textural classifi cation of particle sections.The main conclusion of this study is that, for low iron content ores or tailings, QEMSCANTM can provide much more detailed information on the gangue minerals than OIA. However, for routine characterisation of iron ores with high iron content and containing a variety of iron oxides and oxyhydroxides, OIA is a faster, more cost-effective and more reliable method of iron ore characterisation. A combined approach using both techniques will provide the most detailed understanding of iron ore samples being characterised.

Jul 11, 2011

By D Reid, A Fourie

The in-pipe treatment of slurries with polymer addition shortly prior to deposition is a noteworthy emerging technology of increasing popularity. Although polymer treatment has been shown to substantially modify and improve depositional and dewatering behaviour in a significant number of cases, the impacts of polymer treatment on geotechnical performance of tailings are less well understood. For example, certain combinations of polymer and slurry type have been shown to result in lower final densities at a given vertical effective stress. Despite these lower densities, polymer-treated tailings often exhibit peak undrained shear strengths consistent with untreated material. However, the sensitivity and/or brittleness of the material may be negatively influenced by the looser state created. Although these changes have been studied, most testing available in the literature was undertaken on relatively ‘fresh’ samples of polymer-treated material. However, significant shear may occur following treatment and prior to the commencement of settling and self-weight consolidation as the material moves down the beach.To study the effects of shearing on the subsequent performance of polymer-treated tailings, a test program consisting of consolidation, triaxial and direct simple shear tests was undertaken on presheared polymer-treated material. Materials used were identical to those used in previously published studies on the impacts of polymer treatment in a ‘fresh’ condition. Shearing of the polymer-treated material generally appeared to lessen the impacts of the polymer treatment process. However, the behaviour of the material when sheared indicated that the polymer was still impacting the behaviour of the material in some respects. The results indicate the importance of the consideration of shearing on material behaviour when planning and designing a tailings deposit where polymer treatment is to be implemented.CITATION:Reid, D and Fourie, A, 2015. Effects of shear on the behaviour of polymer-treated slurries, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 215–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

After considerable input from the mining industry, the Canadian Securities Administrators (CSA) finalised National Instrument 43-101: Standards of Disclosure for Mineral Projects. This Instrument, which became law across Canada on 1 February 2001, applies to all technical public disclosure on mineral projects and requires all technical disclosure to be based on the work of a æqualified personÆ (QP). While the QP is quite similar to the Competent Person in Australia there are important differences when it comes to all disclosure. This paper will summarise the main areas in which the Instrument introduces major changes to Canadian disclosure standards on mineral projects including the role and responsibility of the qualified person; the increased requirements to file technical reports; the incorporation by reference of the October 2000 CIM definitions of resources and reserves and additional rules governing written disclosure of scientific and technical information. In October 2001, eight months after the implementation of NI 43-101, the CSA compiled a list of frequently asked questions (FAQs) and CSA responses to assist mining industry participants and their advisors in understanding and applying NI-43-101. This document has been well received by industry. The CSA plans to update the FAQs when further guidance is requested. Two industry committees have been established to provide the CSA with technical advice on the application of NI 43-101. As recommended by the Ontario Securities Commission/Toronto Stock Exchange Mining Standards Task Force, the CSA has established an external industry advisory committee û the Mining Technical Advisory and Monitoring Committee (MTAMC) û to monitor the application of NI 43-101 and advise the CSA on industry and professional developments. The role of the CSA-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Working Committee on Reserves and Resources is to ensure that the future changes and updates to the CIM Standards can be efficiently and effectively incorporated in NI 43-101. During this first year, the Canadian securities regulators have seen an improvement in the quality of disclosure on mineral projects, which will increase investor confidence in the industry.

Jan 1, 2002

By M A. Harrington-Baker, J M. Trudnowski

Sulfate-reducing bacteria (SRB) have the ability to immobilise dissolved metals by precipitating them as sulfides, provided that a favourable biochemical environment is created. Such an environment includes the presence of sulfate, anaerobic conditions and the availability of organic carbon. If such conditions are engineered within a reactive barrier or field-bioreactor, most metals can be effectively removed. To demonstrate this concept, three passive SRB field-bioreactors were constructed in 1998 at an abandoned mine site in the vicinity of Butte, Montana, USA to treat acid mine drainage with characteristic elevated concentration of metals and low pH. Performance of the field-bioreactors, using aqueous samples, was monitored over 32 months until the project was terminated, field-bioreactors were decommissioned and solid matrix sampling of the reactive matter was performed. The most important analytical results are presented in this paper together with conclusions regarding the appropriateness of the field-bioreactors construction features. Only Zn, Cu, and Cd were being removed as sulfides due to SRB activities. Changes in concentrations of other metals (Fe, Mn, Al, As), which do not necessarily precipitate as sulfide, seemed to be affected by SRB only in an indirect manner by responding to increased pH caused by SRB activity. An innovative cellular containment system used for placing organic matter worked very well in preventing settling of the organic matter and ensuring uniform flow of AMD throughout the entire cross-section of the organic carbon with no preferential flow paths This demonstration was funded by the US EPA and was jointly administered by the EPA and the US DOE under DOE contract number DE-AC22-96EW96405. The project was implemented by MSE Technology Applications, Inc, Butte, Montana, USA.

Jan 1, 2003

By R J. Longbottom

In this study the bonding within reduced titanomagnetite-coal compacts was investigated. The aim of the study was to better understand the binding mechanisms in the reduced compacts and, based on this understanding, to improve on their strength.Titanomagnetite ore was combined with sub-bituminous coal to form compacts. The compacts were then reduced by heating in a thermogravimetric furnace (TGA) to temperatures between 1000 - 1300°C under argon. The reaction progress was monitored by measuring the weight loss with time. The reduced compacts were found to have low strength in compression testing. The main form of bonding between the reduced titanomagnetite particles in the compact was by the formation of a slag-like material. Increasing the fi nal reduction temperature was found to have a profound effect on the strength of the compacts by promoting the formation of this slag-like material.Attempts to improve the strength of the compacts were made by changing two variables, the type of coal and the addition of rice husks. The addition of coking coal gave reacted samples that had little strength, while the addition of rice husks may have enhanced the strength of the reduced compacts.

Jul 11, 2011

Nickel laterite HPAL circuits are known for their complexity and have presented a large number of challenges to process engineers worldwide. An attitude commonly encountered by the author is that the beneficiation of the ore is relatively simple and that the difficult problems are in the realms of hydrometallurgy. On a number of occasions beneficiation has become the 'poor cousin' in the process design phase. Another common theme is that significant difficulties are encountered when beneficiation circuits are started up, invariably slowing the ramp-up of the remainder of the circuit. In some cases the problems impact on throughput for a long period and can require major rectification capital. The HPAL Ni laterite projects encountered each have their own set of beneficiation problems that need to be understood before an appropriate circuit can be designed. This paper will discuss a range of design issues including geometallurgy, ore characterisation through laboratory testing, the application of appropriate sizing and analytical procedures, the selection of appropriate unit operations, materials handling of plant feed and products and setting meaningful plant design requirements.

Jan 1, 2008

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By B Besa

Australia is a world leader in the design and operation of mines accessed by the decline method. Literature indicates that a number of metalliferous underground mines using the decline system are also increasing steadily. This increase has generated a great deal of interest in underground haulage systems in future due to the huge costs involved in the development of declines. Studies have also shown that the current method of accessing orebodies by the conventional decline method has proved to be expensive, especially for narrow vein deposits. This is because decline development costs are influenced by mine planning and design parameters as well as available haulage systems that the mining engineer can choose from. The current access method suggests that more waste material is being extracted because of the size of decline openings adopted (5.5 mW and 5.5 mH). Also the conventional 1:7 decline gradient and turning radius of 20 m makes decline lengths, as well as the duration of development, excessively longer. This paper discusses results of a mine design case study with monorail technology as a method of accessing and developing the decline. The proposed system is economical, has high advance rates and offers a significant reduction in capital expenditure. The study compares costs, development metres and the duration of decline development using the monorail system with the conventional (truck haulage) access method. Results obtained indicate that the monorail technology has the potential to reduce the decline length by over 62.6 per cent and decline costs by 63 per cent for the case study. The monorail system also reduces the total capital development costs by 22 per cent for the same case study. Due to rapid development resulting from increased advance rates and the shorter decline length coupled with smaller decline openings, the time to access the deposit reduced by 71.8 per cent. This case study demonstrates that the economics of narrow vein deposits can be improved significantly by using the monorail system of decline development.

Jan 1, 2008

An empirical kinetic model is discussed that enables the number of stages in a carbon-in-pulp plant and the amount of carbon in each stage to be calculated for any desired metallurgical performance. It is shown that a knowledge of the kinetics of gold extraction by activated carbon in each stage assists plant operators in the important' areas of process control and optimization. Factors such as mixing efficiency, concentration and distribution of carbon through the plant, bypassing of pulp through a stage, and carbon poisoning are examined. The resin-in-pulp process for the extraction of gold cyanide is also discussed, and the chemistry of absorption and elution on strong- and weak-base resins is examined. In addition, operating results from a small-scale resin-in-pulp pilot plant are presented, and various applications in which resin-in-pulp may be preferable to carbon-in-pulp are discussed.

Jan 1, 1982

By C Garrido, J Barrera, H Alvarez, L Perez, S Ramirez

In recent years, there has had a greater recurrence of studies and projects that consider tailings filtration followed by dry stacking to reduce the consumption of fresh water, the space required for disposal, and, eventually, to reduce the costs of the project. In addition, this technique could be required to meet new environmental restrictions to extend the life-of-mine of existing plants or to enable the development of new projects, especially in areas of high social interest. This article is intended to describe the most relevant technical aspects of the design and implementation of an iron ore tailings filtering system and its final overland disposal as well as physical and metallurgical surveys, and laboratory and pilot testing. Furthermore, it is presented how these activities are inserted in the project development to rationalise the resources. The case under study considers an iron mineral wet magnetic concentration processing plant. The outcome tailings are dewatered by means of thickeners, where the overflow water is recycled back to the plant. The underflow slurry is pumped into intermediate storage tanks before proceeding with further dewatering and final disposal. The project consists of a tailings filtration plant, belt conveying systems, a temporary stockpiling system, trucking loading and transportation system, moisture-conditioning facilities (spreading and airing), and final disposal facilities (compacting). Due to the stickiness of the filtered tailings that governs the belt conveying system design, the operating moisture range must be established. Besides, proper technical aspects such as planning, executing, and analysing both the laboratory and the pilot testing data to validate process design parameters; selecting filters; defining spare filtering capacity; handling the out-of-range filtrated moisture; sizing the belt conveying system; configuring the equipment involved, must be considered.

Nov 8, 2021