Search Documents

By D Sidea

There has been increased focus in Australia on large diameter raise boring for ventilation shafts and orepass excavation in good quality, brittle, highly stressed rock. As mining in many parts of Australia progresses to deeper levels, more vertical openings are being excavated in highly stressed ground conditions. However, whilst shafts have been successfully raise bored in highly stressed rock, it is often at a significantly increased risk of loss or damage to inhole equipment. It is important for both mine owners and contractors to have an appreciation of these risks at the planning and tendering phases of raise boring contracts. This paper provides an understanding of the risks associated with large diameter raise boring and a review of methods to predict failure in highly stressed rock.

Jan 1, 2005

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

By Yu H, Wan B

40 percent of the coal reserves and 40 percent of the ouput of coal in China is of thick coal seams. The sub-level caving in Yangguan has evolved together with the hydraulic supports, to provide recovery rates today of 80 to 85 percent, waste ratios less than 10 percent and daily outputs exceeding 7,000 tonnes. Matching of rate of shearing bottom coal to caving of top coal is most important to achieve "simultaneous" operations. Spontaneous combustion in the goat, gas, including in the goal, and dust, are particular safety hazards which are combatted with various stringent measures.

Jan 1, 1991

Viking Holdings Ltd, a Todd Corporation company, is active in the mineral industry through operations, joint ventures and equity investments. Identification and management of risk is key to the success of the company. This paper discusses risk in general terms and in the context of Vikings activities. Reference is made to the current environment and the impact of risk and environment on profitability.

Jan 1, 1997

Removal of Arsenic in Enargite from Copper Ores by Flotation and Leaching in NaHS Media

Sep 13, 2010

Traditional techniques for extracting pillars in thick underground coal seams in India are reviewed. Problems encountered are principally control of roof strata and low recovery. Recently developed mechanized methods and projected newer techniques are discussed.

Jan 1, 1986

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

By Medhurst TP, Trueman R

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface mod- elling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model pre- dicted the fender would suffer considerably more de- formation and strain.

Jan 1, 1992

By Gray E, Banks J

In mine site revegetation, exotic grasses are more commonly used than native grasses. This is due to unavailability of native grass seed on a commerical scale and lack of information on agronomical aspects of native grasses. This paper lists a number of native grass species that have the potential to grow well on mine sites, and provides some information on their seed collection, processing and germination. Further, it demonstrates via results of a field trial conducted at Ranger Mine spoil the relative performance of ten native grasses and Rhodes grass. It is concluded that (i) some native grasses have similar ability to grow on mine spoils compared to Rhodes grass and (ii) the use of native grasses have added advantages in ecosystem restoration.

Jan 1, 1994

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. Strong outbursts often have occurred in geological tectonic zones and concentrated stress areas. There are some particular characteristics of these strong outbursts, including the effects of ground stress, gas pressure and the properties of coal associated with the outbursts.

Jan 1, 1986

By McKinnon R. L

Laboratory and field work on the use of wetting agents for suppression of colliery dust is described. Although the results were inconclusive they were not discouraging and further investigation is required. The use of certain wetting agents may constitute a healthhazard.INTRODUCTIONCoal dust presents explosion and health hazards to the coal mining industry. The problem of dust suppression is particularly acute where water alone is unsatisfactory for this purpose. The addition of a surface active agent (wetting agent) to the water should enable the dust particles to be more easily wetted and thus more easily prevented from entering and spreading through the mine atmosphere.Investigations into this effect carried out at The University of Sydney mainly under research grants from The Joint Coal Board (Dawson and Hargraves, 1955; Charlton and Curnow, 1957) are summarized, and information on the possible harmful effects of certain wetting agents is given.Twelve local manufacturers and five importers supplied 52 wetting agents in liquid, solid, powder, and paste form.The active material content varied from approximately 10 per cent to 100 per cent and the cost per pound from 8d. to 14/3.LABORATORY TESTINGPossible test methodsThree methods of laboratory testing were considered.1. The standard method for comparing wetting agents is the Draves test, used in the textile industry on cotton...

Jan 1, 1961

By Lamont G

The significance of blasthole stemming in determining blasting efficiency has been extensively studied for small diameter holes using gelignite explosives. Recent developments in blasting technology with the use of large diameter holes and low cost blasting agents have not included studies of the effectiveness of different types of stemming materials. A review of previous measurement techniques and the relevance of these earlier results to present stemming practice is presented in this paper. A survey of operating mines in Australia provided information for this analysis. The value of stemming in reducing blast noise and improving blasting efficiency is generally accepted but the use of bulk-loaded explosives in underground operations has resulted in the practice of eliminating the use of stemming material.In surface operations drill cuttings are used for stemming on the basis of availability rather than efficiency in providing resistance to movement. The development of laboratory testing techniques, based on noise level and borehole pressure measurements, to evaluate the relative efficiency of different types of stemming materials is described. The results of an extensive series of tests with ANFO explosive showed similar trends tothose obtained from earlier published results with gelignite type explosives. Conclusive quantitative results on the relative effectiveness of different stemming materials will require minor modifications to the existingequipment. Observations and the results of pressure measurements indicated the presence of shock wave effects which caused the ejection of the top section of the stemming column when using coarsely fragmented material.

Jan 1, 1979

By G R. Mould

The paper presents a general background to the subsidence research program being undertaken by the Department of Mineral Resources and Development in New South Wales. The results of the studies undertaken over the last ten years are summarised. The differences between these results and those obtained by the National Coal Board are discussed. The results of a study carried out on the effect of total extraction beneath a freeway in the southern coalfields are discussed in some detail. The procedures developed for the construction of a 500 mm diameter natural gas pipeline crossing a number of collieries in the northern coalfields are also outlined. The future direction of the Department's subsidence research program is discussed.

Jan 1, 1980

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By Met B. E

The increasing pace of modern mining makes constantly greater demands upon the several contributing departments of rock breaking and transport, and rock-drilling, as the spearhead of attack, has received a great deal of attention with respect to both machines and steels. By a series of mechanical improvements, combined with the application of selected heat-treated alloy steels, the rock-drill has now been developed into a machine capable of rapid drilling and long service under severe working conditions. As a factoryproduct made under strict metallurgical control it is as foolproof as, say, the modern automobile, and, like its prototype, it can be kept in efficient operation by a minor amount of attention during use and by periodical adjustments and replacements.The same cannot be said, unfortunately, of the drills with which the machine is supplied; in conventional mine-shop practice these are made of the best tool steel shaped and heat-treated under the poorest of metallurgical conditions.The crudities of steel-shop practice have, in fact, always prevented the full exploitation of the steels available at any time, and even at the present day the general standard of treatment offers a contrast with the quality of the steels which moves the metallurgist to amusement, despondency or outrage, according to his temperament. Nevertheless, the tendency persists to meet the increasing demands of the rock-drill primarily by the use of still better steels, and secondarily by improvement, of the steel-shop practice. Athird type of development is the introduction of factorymade tools in the form of detachable bits and rods. It is proposed in this paper to deal with these three aspects of the recent developments in rock-drilling.*Re-written from a lecturette given during the First Ordinary Meeting, 1936.

Jan 1, 1936

New Zealand has been a significant producer of gold for over a century. Total recorded production is over 850 tonnes. There were three major periods of production: the first and biggest was between 1860 and 1880, the second was between 1895 and 1920 and the third was between 1930 and 1945. After 1945 gold production fell continually until 1980 when the major upward adjustment in gold price led to renewed interest. There have been important new developments in each of the known gold-rich areas: Westland, Otago and Coromandel and exploration for gold in these areas and in previously unprospected regions has reached unprecedented levels.

Jan 1, 1988

The importance of the Broken Hill mining field may be gauged from the fact that since the discovery of the ore-body in 1883, till the end of 1931, approximately 43,000,000 tons of ore have been raised.The lode covers a length of 31 miles, and in places is upwards of 300 ft. in width. The ore, as at present mined, consists of an intimately blended mixture of lead and zinc sulphides with silver and gangue minerals.Structurally the lode conveys the impression of a huge longitudinal arch (when viewed from the east or west), having its apex or crown near the centre of the field, in the leases of the Broken, Hill Proprietary Co. Ltd., where the lode outcropped at the surface.The minimum depth of the lode in the Proprietary mine was some 500 ft. from the surface, but huge undulations, having an average pitch of 45°, carry the extensions of the arch gradually deeper, to those places where active stoping operations are now in progress in the workings of the North mine at one extremity, and the South and Zinc Corporation mines at the other. The depth of the lode from the surface, as exposed at present, is approximately 1700 ft. at these extremities.The structure and physical character of the ore-body, and its containing walls, are so complex and varied that almost every type of mining problem is met with.

Jan 1, 1932

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By Mallett CW, Rynn JMW, Hammond RH

Geological studies and satellite imagery of the Bowen Basin in Central Queensland, Northeastern Australia, have shown that the significant structural controls are a series of major North East/South West (NE/SW) trending structures, which can be traced as lineaments on Advanced Very High Resolution Radiometer (NOAA-AVHRR) imagery as well as on both Landsat Multi-Spectral Scanner (MSS) and Thematic Mapper (TM) imagery. These linea- ments can be traced offshore and into the Coral Sea by the distribution of offshore reefs and the bathymetery of the Queensland Shelf and the Queensland and Marion Plateaus. The seismic activity in Eastern Queensland seems to be divided into two distinct provinces separated by a seismically quiet area. This apparent seismically quiet area is bounded by two of the large lineaments seen on the satellite imagery. These features could be related to the deep crustal structure of Eastern Queensland and to the opening of the Coral Sea.

Jan 1, 1987

By Benkendorff P. N

Cement production in Australia approximates 6.5 million tonnes per year. Cement clinker is sourced from 15 plants which operate 28 kilns. Cement grinding is conducted at 14 of the clinker plants plus 7 grinding plants. Average annual capacity per kiln or plant is lower than in many overseas countries, but kilns introduced since 1970's have been of larger size more in keeping with size trends overseas, although still smaller than the large units overseas. Substantial economies in capital and labour costs can be achieved in large production units, particularly with dry process kilns using precalcination techniques in which part of the fuel is introduced in the static preheater section ahead of the kiln while the balance is added to the kiln in a conventional manner. Precalcination techniques have been introduced to the Australian cement industry but as cement transport costs form a major part of supplying diverse market areas, the size of kilns is likely to remain less than maximum owing to balance with distribution costs. The cement industry uses significant amounts of thermal and electrical energy which can be minimised by proper selection of equipment and technology. Labour costs are also significant and can be contained by automation and computer control of the process.

Jan 1, 1989