Search Documents

Once and for all, the debate on the exponent in Gy's formula is pushed to its limit. It is explained why an exponent of 2.5, obtained when using a square root of nominal size d to adapt the value of a calculated liberation factor to a different comminution size, will rarely be encountered in practice, if no arbitrary decisions are made.

Mar 1, 2010

A Devonian metallogenic province is extended northwards from central Queen- -sland to the Burdekin Basin in the Charters Towers Gold and Mineral Field. Devonian sediments of the Burdekin Basin are intruded by mineralised quartz felspar porphyry which occurs as pebbles in Upper Devonian conglomerate. A mineralised volcanic complex lies on the crest of an anticline in Devonian sediments.Red siltstone is slurried and reduced to pyritic hornfels over folded limestone.A thick wedge of volcanogenic conglomerate overlain by marine shale lies on the mineralised rim of an ocean which suffered cataclysmic changes during Late Devonian times.

Jan 1, 1987

By Barro L

Very large reserves of gas are contained in coal. Because of the low permeability of the coal gas flow rates are very low. Fracturing of the coal can be achieved by use of the nitrogen - foam frac techniques described but the flow rates after fracturing are not sufficient to support economic development. Fracturing of the seams in the Bowen Basin was as predicted but in the Sydney Basin no trace of the fracture could be found when development proceeded past the fractured well. Testing of coal samples has provided some insight into parameters affecting desorption Rates.

Jan 1, 1982

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

By Y Xie, L O’Connor, S C. Dominy

Sheeted vein gold deposits are characterised by multiple subparallel veins and often free milling gold. Variability in gold grade and recovery parameters are enhanced by poorly designed sampling and test work protocols. Poor quality samples generally equate to an enhanced nugget effect. A sample can be described as being representative when it results in acceptable levels of bias and precision. Total sampling variability can be quantified by the relative sampling variance, which measures the total empirical sampling variance influenced by the heterogeneity of the lot being sampled under the current sampling / test work protocol. Effort should be made to minimise the relative sampling variance through Theory of Sampling (TOS) and quality assurance / quality control (QA/QC) application. This contribution reports on a case study that exemplifies how high-quality grade and recovery data can be gained from a well-designed and planned drilling, sampling and test work program, followed by bulk sampling. Results across historical resource drilling, geometallurgical drilling, laboratory assay / test work, geometallurgical modelling and a bulk sampling/pilot processing study are reconciled. A whole core, entire-sample test work protocol was used to acquire fit-for-purpose gold grade and recovery data for inclusion into a Pre Feasibility Study reported in accordance with the JORC Code.CITATION:Dominy, S C, O’Connor, L, Xie, Y and Glass, H J, 2017. Geometallurgical sampling protocol validation by bulk sampling in a sheeted vein gold deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 185–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

A wide range of models are available to computer process simulators that require a large number of parameters which often are physical measurements, coefficients, calibration factors and functional forms. This makes it intuitively difficult in the majority of cases, to tune the parameters in order to simulate a circuit in agreement with experimental results. Unit calibrators operating on the principle of least squares minimisation of the difference between predicted and observed plant data, are relatively successful when the parameters are unconstrained and independent of each other. In the case of constrained parameters, a set of carefully chosen transforms is presented which map the unconstrained variables being minimised into the constrained parameters required for the model. This technique has been used successfully with the Powell minimisation algorithm and it may also be applied to other unconstrained minimisation methods. Necessary model characteristics are discussed to enable these transforms to be applied to interdependent model parameters such as points of a graph. Examples of the calibration of several unit models using these transforms are presented. KEYWORDS: Calibration, optimisation, transforms, process simulation.

Jan 1, 1993

By R Thompson, D Tulloch

"Wet-weather or 24×7 wet-trafficability is a commendable design objective for unpaved mine haul roads, but practically often difficult to achieve, due both to the road sheeting material selected, and also its breakdown under the action of traffic and environment. Accidents allied to wet-trafficability issues, either due to rain or often more commonly, over-watering of mine roads, is increasing and especially the loss of control or uncontrolled vehicle movements categorisation. The dominant system failure is that once vehicle control is lost, control cannot be regained.The friction supply, or ‘skid resistance’ of a mine haul road sheeting is critical to the safe operation of the road and data has to be collated concerning the variation of friction supply with sheeting material engineering or indicator properties. In the light of the paucity of data existing in this field, this paper presents the contributory research that informs the development of improved and validated unpaved mine road friction supply estimates, based on a number of mine site evaluations across a range of sheeting material types and characteristic parameters, leading to improved predictive models of friction supply.Results from this preliminary review will enable operators to assess their road sheeting materials, improve and validate unpaved mine road friction supply estimates. This will contribute to improved road design, management and 24×7 operability decisions and contribute to a reduction in heavy vehicle loss of control incidents on gravel-surfaced mine haulage roads.Citation:Thompson, R and Tulloch, D, 2016. What's Stopping You? The Role of Sheeting Material Selection in Safe Haulage Operations, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 253–264 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Intermontane valleys form unusual features of compressive mountain belts both in the sharp topographic break they represent and in the strike-slip displacements often associated with the valleys. Such strike-slip motion seems hard to reconcile in the actively deforming Andes where reconstructions have indicated nearly perpendicular Cenozoic plate convergence. Detailed study of a part of the Argentine Andes between latitude 31-33¦S suggests that, although strike-slip displacements may have largely created a prominent intermontane valley system, no Holocene strike-slip displacements are observed amid the relatively active compressional deformation along the mountain belt flanks. New plate reconstructions, treating the Nazca plate as two microplates separated by fractures along the Nazca Ridge, predict large components of strike-slip motion between the South American and Nazca Plates for the period from 10 to 5 Ma. These reconstructed plate motions are consistent with strains derived from recent kinematic analyses of minor faults along the southeast margin of the Puna plateau and the general timing of tectonic phases in the Andes.

Jan 1, 1987

By Quast K. B

Samples of limestone and micaceous hematite have been ground in a laboratory batch mill using equal weights of either rods or balls. Values of the Schuhmann distribution modulus, a, have been shown to depend on grind time and do not remain constant as often reported. The linear reduction in a with grind time was attributed to a change in grinding mechanisms with time. The product sizing from ball milling limestone showed a bimodal distribution, but rod milling produced a unimodal size distribution. The product sizing from milling micaceous hematite was difficult to interpret due to the major influence of the shape factor on the transition from screen sizing to cyclosizing.

Jan 1, 1995

By O Dahl, I M. Platten, E J. Sides

Many narrow-vein gold deposits are characterised by a high to extreme nugget effect and the presence of coarse gold. They rank amongst the most difficult of deposits to produce an accurate and precise resource estimate. This contribution presents a case study from the Nalunaq Gold Mine in Southern Greenland. The mine commenced operation in May 2004 and is currently operating at a rate of 400 tonnes per day, to produce about 100 000 oz gold per annum from a total resource base of 1.2 Moz. Mineralisation is characterised by quartz veins that are hosted within a shear zone that is continuous over about 1000 m. The principal orebody is the Main Vein structure, which ranges up to 3 m in width, maintains an average dip of 35¦SE, and contains significant gold grades (1000s g/t Au). Gold particles are often visible, with 25 per cent being greater than 250 microns in size. Variography using underground development samples indicates a nugget effect of about 75 per cent. For the 2005 resource estimate, a 2D metal accumulation ordinary kriged block model was used to produce a global grade for the Target and South Blocks of the Main Vein. Grade control chip-channel samples are collected from æshantyÆ drive footwalls, and used as the basis for both the kriged block model and to determine the grade of individual stope blocks by peripheral weighted averages. Geology plays a key role in mining efficiency, given the locally variable nature of the ore zone.

Jan 1, 2006

By Jones S. C

A specific arc can be cut in hard rock formations using a specially designed multistep piloI bit, variable sized drift joint and long heavy control rod as a stabilizer rather than the Vaughan Thompson "Lifting" arc cuttingequipment. The rate of deflection can be controlled after an initial determination of behaviour in any particular rock type.

Jan 1, 1966

By D Millette, F Gay

Surface tailings are finely ground waste materials produced in all mines after the mineral or metal has been removed from the metallurgical process. Current methods for disposal of tailings involve constructing dams, dumping into existing waterways, and depositing as backfill underground. Each method has its drawbacks in terms of cost, level of complexity, safety and environmental concerns. Backfilling is the process whereby waste material (generally metallurgical tailings, prepared aggregates or a combination) is placed from the surface back underground into open mine workings via conveyor belts, hydraulic or pneumatic pipes or gravity. In the backfill process common difficulties are expensive placement costs, equipment wear and the ability to meet early and long-term strength requirements. Traditional tailings transportation in pipes involves the use of water as the transport medium. Foam technology involves the introduction of micro-air bubbles that replace the water as the main transport medium. This air can be removed after placement if necessary, by the addition of a defoaming agent. This could produce an under-saturated stable cake. Foam technology has the potential to revolutionise surface tailings disposal and backfilling by providing a less expensive and environmentally safe alternative to those just described.

Jan 1, 2000

By Minglin W, Zhixing L

The laws of detonation wave velocity variation in propagation process along the charge under channel influence are investigated widely in this paper. The result is obtained by blasting experiments. Bore hole is simulated by plastic tube or steel pipe (with outer diameter 45 nun, inner diameter 40 or 41 mm). Blasting experiment is carried out with a cylindrical charge of 32 mm diameter. The author analyses the characteristics of energy distribution along the charge under above-mentioned conditions. Reasonable initiating position and initiating direction are also analysed. A double-direction initiating method which consists of several initiating charges is put forward. The blasting effect of this initiating method when used in underground mining is stated out.

Jan 1, 1990

By Wooltorton B

Highwall failures in surface coal mines in Queensland occur as circular slips through weak and weathered material, or as bilinear slides on sub-horizontal surfaces and steeply dipping joints. Weak horizontal planes occur in the Permian-Tertiary unconformity or on bedding surfaces within the Permian Coal Measures. Sub-vertical movements occur along rock joints and tension cracks induced by stress relaxation after excavation. Blasting also introduces new fractures and causes movement along existing rock discontinuities. Critical factors for stability include the dip direction of potential failure surfaces, shear strength of the rocks, damage due to blasting prior to highwall excavation, groundwater conditions, the type and performance of clays on shear surfaces, and pit geometry.

Jan 1, 1981

By Mroczek C. R, Evans D. A

Renison is a world-class ore deposit that has been mined for over 100 years. It currently has reserves of 5.06 Mt @ 1.88 per cent Sn and a projected mine life of 8.5 years. Recent advances in the geological understanding of the deposit have been associated with detailed structural and geophysical investigations accompanied with the discovery and exploitation of the Rendeep orebodies. Mineralisation is linked to the forceful emplacement of the Devonian Pine Hill Granite that resulted in a complex brittle (-ductile) deformation of the Eo-Cambrian host stratigraphy. Dilation jog development on the Federal-Bassett Fault in the Federal and Rendeep areas provided access for cassiterite-rich magmatic hydrothermal fluids responsible for carbonate replacement Mineralisation.

Jan 1, 1997

By H A. Linn, K Winn, C W. Lee

The Q-slope method for rock slope engineering was developed to enable engineering geologists and rock engineers to rapidly assess the stability of excavated rock slopes in the field and make optimal adjustments to slope angles as rock mass conditions become apparent during construction of road cuts or benches. An empirical relationship between Q-slope and long-term stable slope angle is now supported through over 500 cases studies from Asia, Australia, the Americas and Europe. This paper presents about the stability analysis by first-ever applying Q-slope method on abandoned quarry wall in Singapore. The 30 m high rock slope which is composed of monzogranite rock was severely damaged by blasting operation. As the rock slope is intended for public view the objective was to retain the natural outlook and without any artificial support application thus manual scaling was carried out to clear the loosed rock blocks. In the end stable slope angle of clean rock face is determined once again by Q-slope method.

Nov 29, 2022

By D Joshi, J Rostami, M Karakus, A Eustes

The first target of mining activities on the surface of the moon is to find and extract water from the icy regolith on the moon. A test drilling unit was designed and fabricated under a NASA Early Stage Innovation (ESI) grant. A high-frequency data acquisition system was used to record drilling responses at 1000 Hz. Parameters like weight on bit (WOB), torque, rev/min, rate of penetration (ROP), mechanical specific energy (MSE), field penetration index (FPI), and the uniaxial compressive strength (UCS) were recorded for 40 boreholes in the analog samples made of regolith simulant and specialised cement. Development of the AI system and machine learning (ML) algorithms for analysis of data to evaluate strength and hence water content of icy regolith required a large data set. In this case, the data set comprising of more than one billion data points recorded while drilling into various analogue samples and cryogenic lunar formations to optimise power consumption and make bit wear adjustment during drilling operations. The tests were also repeated in the samples of icy regolith at various water content at -190C to verify the ability of the algorithms to analyse the data and to estimate the strength of the frozen formation and hence water content. The paper will discuss the objectives and methodologies used in the project and reviews the testing program and the machine learning (ML) algorithms ability to identify various formations along the exploration boreholes.

Sep 1, 2024

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

By Spencer GA, Saul SJ

The flight line spacing in low level aeromagnetic surveys is the principal factor governing both the cost and the amount of geological detail which can be extracted from the data. The rate at which geological resolution diminishes with wider line spacing is illustrated by progressive subsampling of a 200 m spaced data set from the Charters Towers region in Queensland.The usefulness of high frequency type filters in enhancing shallow structural features is seen to be limited to the 200 m data.It is concluded that each data set is suited to a particular scale and style of geological investigation with only the 200 m data having sufficient detail to identify the subtle structural patterns which are crucial to mineral exploration.

Jan 1, 1976

This paper presents the findings from an experimental study of the effects of shock and gas penetration breakage mechanisms in rick blasting. A blasthole liner method, which realistically seperated these two basic sources of energy in blasting, was developed and utilized. The use of four different explosives with contrasting detonation behaviour produced a wide variation in the nature of explosive energy transfer to the rock. Through extensive field experiments it was found that, relative to low VOD dynamite, the high VOD emulsion imparted greater shock to the rock and therefore produced finer fragmentation and greater back damage. The comparatively lower heave energy of the emulsion caused less immediate blast results were obtained with watergel and ANFO explosives, which have detonation behaviour and energy partitioning charecteristics lying between emulsions and dynamite.

Jan 1, 1990