Search Documents

By J Palaci, M MelTndez, F Parra, I Rojas

At the Huasco Pellet Plant of Compa±fa de Aceros del Pacffico, Chile, the production of iron concentrate suitable for pellet feed from a low-grade iron ore was technically evaluated. In this study, three treating schemes including comminution, magnetic concentration and flotation in pneumatic cells were tested. The best results were obtained at the laboratory scale by flotation technique using Lilaflot D 817 M as the collector without using any depressant. The operational parameters were determined including pneumatic flotation, and three circuits, two including magnetic pre-concentration, with the low-grade iron ore. The best results were obtained by size reduction at 80 per cent under 325 Tyler mesh, three steps of magnetic concentration and three steps of flotation in pneumatic cells. The magnetic concentrate contained 63.02 per cent of iron and 6.6 per cent of silica, and after the pneumatic flotation the iron content increased up to 70.18 per cent and silica decreases to 1.07 per cent with 78.78 per cent of iron recovery at a weight recovery of 31.89 per cent. Therefore, it is possible to use low-grade iron ore to produce pellet feed from magnetic concentrates by using reverse iron flotation in pneumatic cells.

Jan 1, 2005

The paper deals with the taking of soundings in connection with coal mining operations under part of the Pacific Ocean adjoining John Darling Colliery.INTRODUCTIONIn the early days of mining in the Newcastle District there did not appear to be any definite law specifying the limits to which mine workings, other than certain borings, could extend under tidal waters.As time went on, a figure of 120 ft. was fixed as the minimum thickness of strata between the roof of the seam and the sea bottom; beyond this mining operations are disallowed. The laws relating to working coal under tidal waters are as follow:-The minimum width of pillars to be left shall be eight (8) yards and the maximum width of bords or other excavations shall be six (6) yards, but the lessee may at his discretion increase the minimum width of the pillars or decrease the maximum width of the bordsor other excavations so as to increase the general safety.The eight (8) yard pillars shall be left unwrought.In on-road of every pair of Winning-off or leading headings, a bore shall be kept going ten (10) feet in advance for the purpose of foretelling the presence of any fissure, wash-out, open joint, fault, dyke, or otherwise, and all winning-off headings shall be driven atleast one hundred (100) yards in advance of the working bords.The most accurate and trustworthy information shall be obtained by the lessee not only' of the depth and character of the ocean bed, river, lake, or estuary deposit, but also of the strata overlying the coal seam.When working under the ocean, strata shall be bored through and proved a minimum thickness of thirty (30) feet at the face of the leading headings or levels immediately such headings or levels are under the ocean, and...

Jan 1, 1947

We can look at the water treatment and management strategies at some recently commissioned mines and minerals processing sites to see the likely future of water in mining. The future of water in mining will be based on a holistic approach to understanding the site water balance, appropriate treatment, reuse where possible, and environmentally managed discharge where required. This paper describes advanced and innovative water treatment and reuse processes as used by mines and mineral processing operations from around the world. Underground mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Mining and processing often accumulates wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and acidic and odorous sulfates. On-site reuse, environmental discharge requirements, as well as community needs for water, drive mine operators to consider the most appropriate water treatment process. Mining water treatment for the future is described using case studies of innovative processes. The case studies include treatment of mine dewatering water for beneficial application from Australian mines, Ballarat Goldfields and Bendigo mining, treatment of produced water from oil and gas projects, and treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Advanced and innovative processes including membrane filtration, reverse osmosis at extreme conditions, advanced biological treatment and water management are all part of these case studies. This paper uses real case studies of advanced and innovative mine water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is on innovative processes that may be more widely used in future mining û where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the mine or the local community.

Jan 1, 2008

By Johnstone RD, Rattenbury MS

RACE Quartz-calcite veins containing Au, As, W, Cu, Pb, Zn and Fe cross-cut Alpine Fault- related structures in the Alpine Schist of South Island, New Zealand. These veins, and some other related veins have been deposited by metamorphic fluids at 250¦C to >320¦C at pressures of a few hundred bars. The fluids were very variable in composition, with 0 to 50 mole % CO2 and 2 to 18 wt. % NaCl equivalent. Penetration of hot metamorphic fluids to shallow levels in the crust was facilitated by rapid uplift of hot rocks at a compressive plate margin. Fluid immiscibility at shallow levels caused concentration of salts and metals into the aqueous phase. Gold precipitation was caused by reduction by pelitic country rock and/nr dluILion by other aqueous fluids.

Jan 1, 1987

By OÆBrien R. T

A small static bed was used to study the thermal cycles required for the heat hardening of pellets based on synthetic magnetite concentrates and a naturally fine hematite. This apparatus can be employed to yield broad process data for the design of a recuperative strand system operating on the magnetite concentrates.Various alternatives are given for a process to heat harden the hematite ore but a preference is given to the production of a self fluxing pellet. Bond types and general mineralogical structures are interpreted against the optimum firing cycle necessary to produce a defined quality of pellet.INTRODUCTIONThe work reported in this paper extends that on the "Heat Hardening of Artificial Magnetite Pellets", which was described at the International Symposium on Agglomeration, sponsored by the American Institute of Mining, Metallurgical and Petroleum Engineers at Philadelphia, U.S.A. in April 1961. Whereas that work was of a more basic nature, serving to illustrate the suitability of artificial magnetites with various admixtures, to the application of heat hardened pellets, on this occasion the aim is to illustrate the procedures which were used to establish the dimensions of commercial recuperative strands for Australian raw materials.The nature of the pellet feed, Le. relatively uniform spheres of + i in.-Yi6 in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas flows...

Jan 1, 1963

Early efforts to control the dust necessarily produced during dry crushing operations, took the form of venturis at loading chutes and other places where dust was most evident. These venturis discharged to the atmosphere and for obvious reasons were not very satisfactory.Attempts to collect the dust drawn off by the venturis, using dry cyclones, were not successful, the cyclones catching only the coarser particles. Further, no satisfactory method of continuously discharging the dust catchment was evolved. Water sprays were also used, and will be referred to later.In 1940, a single discharge fan of 3,000-4,000 cu. ft. per minute capacity, was installed to draw the dust-laden air from the Symons crushers and ·screening sections with their attendant conveyors. Suction was through two 15 in. ducts which branched off into 10 off-takes situated over the conveyers at points of discharge from crushers and screens.A dry cyclone was installed in front of the fan, which exhausted into a bag-house.The cyclone suffered from the defects of the smaller units mentioned earlier. When the collected dust reached a certain level in the cone, no more collection would take place until the cone was emptied. This objectionable feature was overcome by introducing a jet of water ahead of the cyclone. The water and dust collected overflowed a weir and were pumped to the mill.

Jan 1, 1948

By A Struminski

The principles of occupational risk evaluation resulting from the improper ventilation of the underground mines were presented. It was shown that the risk level implies the appropriate planning and usage of prevention methods. That approach is fundamental in the ventilation, fire and climate safety management in the copper ore mines. The paper uses the adequately modified Risk Score method.

Jan 1, 2003

By P D. Munro

The spatial distribution of ore with similar processing properties or domains within an orebody may be identified early in the assessment of an orebody to provide a sound basis for later development of the orebody. The assignment of domains in the primary sulfide portion of an orebody is often more difficult than recognition of the oxidised, supergene and related domains usually located towards the top of the mineralised volume. This paper will discuss some approaches to assigning domains within the primary sulfide portion of an orebody. The processing properties of each mining block will be known if the contained domain(s) and their proportions are known. The use of both physical and chemical ore properties to assign the domains is discussed. The domains based on similar processing properties do not necessarily coincide with geological zones assigned by geoscientists. As part of assessing the physical properties of ore, the modal analysis of the ore with respect to the valuable sulfide minerals and the sulfide and non sulfide gangue minerals has to be known, along with the traditionally used elemental assays for valuable and penalty elements. Two scales for determining other physical ore properties will be considered: the mesoscopic scale (examined by human eye) and the microscopic scale (examined via a microscope under high magnification). The strengths and weaknesses of the data obtained at the two scales are discussed in the paper. Broadly, data collected at the mesoscopic scale are much less expensive but the types of data available are more limited. Methods for evaluation of chemical ore properties are also discussed. After establishing a basis for establishing the spatial distribution of domains, variability testing is required to verify the integrity of the designated domains. In contrast, each block of ore in some orebodies has been assessed principally via the results of a laboratory separation on a number of drill core samples or composites from throughout the block, with minimal or no attention to the concept of domains.

Jan 1, 2008

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By Bilodeau M. L

The paper describes a model which has been developed to assess the economic charac- teristics of base metal investment in Canada and the effects of past, present and possible future sharing systems, particularly mining taxation systems, thereon. The model is illustrated by applying the 1976 Canadian tax system to the economic characteristics of base metal discoveries made in Canada during the 1951-1974 period.

Jan 1, 1977

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

By D Phillips

One of great challenges is to determine the exact timing of gold mineralisation in centralVictoria due to suitable materials and/or geochronological techniques. Here we report new mica and pyrite 40Ar/39Ar age data by laser probe and step-heating furnace analyses, and discuss problems in data collection and interpretation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

The large El Cerrejon coal open pit in north east Columbia has been developed over the last decade in a remote, entirely new mining area with hitherto unskilled inhabitants. Now over 200 pieces of heavy equipment operate with high reliability and availability due to successful theoretical training and skill improvement programs tuned to the specific reliability needs of the worksite and environment. The process of continuous improvement adopted promises further competitive advantages of the project.

Jan 1, 1991

By N C. White, L Danyushevsky, D R. Cooke

Comb-layered textures preserve the cyclic accumulation and release of volatiles inside magmas that are temporally associated with large Cu-Au-Mo-rich porphyry ore deposits. Fluid inclusions in these textures sample pristine magmatic fluid. Microanalysis of this fluid helps constrain the physical models that operate at melt-fluid interface and in the broader magma system responsible for ore deposit formation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

The longwall system with caving is the most common mining system in Polish Collieries and the extraction is carried out simultaneously on several levels and in different seams. The extent and diversity of the methane hazard occurring is strictly connected to the specific geological and gas conditions as well as to the applied mining methods. Taking these factors into consideration the following methane drainage methods are applied as additional means of combatting the methane hazard in Polish gassy coal mines: 1. predrainage by means of boreholes drilled from the surface, 2. predrainage from stone drivages and devel- opment workings, 3. degasification of coal extraction workings, and 4. degasification of sealed-off areas/old goaves. Predrainage gave satisfactory results when holes were drilled from the surface or from underground workings, but only to depths to 300 m. It was necessary to adapt methane drain- age methods to the geological and mining con- ditions as gassiness increased with depth. The results of methane capture, both pre- drainage and post drainage were obtained by investigating several gassy mines.

Jan 1, 1982

How Particles Stick to Bubbles - The Influence of pH and Hydrophobicity in Flotation

Sep 13, 2010

The application of reinforcement techniques to enhance the stability of underground coal mine roadways subject to high stresses is discussed. Research conducted in the Illawarra Coal Measures has been aimed to delineate the factors which influence the behaviour of rock above roadways and the performance of the reinforcement placed. Design considerations for the reinforcement of mine roadways in the Bulli coal are based on a quantification of the rock response together with a reinforcement strategy to enhance the structural integrity of the roof strata.

Jan 1, 1986

By Mallett CW, Hammond RL

Geological maps of the Pacific Rim recently published by the Circum-Pacific Council for Energy and Mineral Resources have provided a useful perspective from which to view modern plate interaction and the evolution of modern fold belts. An important lesson from any study of modern plate interaction is that of the normality of change. The chaotic is more usual than the simple. Present day convergent margins with mixed characteristics are measures of this chaos. Indeed, the character of less than one third of the present length of the Pacific Rim can be ascribed to conventional models of plate interaction. Another lesson is that of the great mobility of oceanic crust. Enormous areas of the Pacific may not be represented in future fold belts developed at convergent boundaries unless normal consumption processes are disrupted, and even then only by linear zones a few kilometres wide. The axes of divergent boundaries creating Pacific Ocean crust have been equally mobile, with new spreading sites taking over from older sites through time. Divergent boundaries, whether active or inactive, consist of oceanic crust, and may be wholly consumed at collision sites with convergent boundaries. Their only potential contributions to fold belt evolution are transforms and magmatic activity. It is this transform component that can provide us with a mechanism to explain the apparent contradiction of both compressional and extensional features occurring together in a developing fold belt. Reconstructions for the SW Pacific are used to demonstrate that the fold belts under construction during the last 4% (Jurassic- Recent) of geologic time have involved interaction between convergent, divergent, and transform boundaries. In the last 15% of earth history (Late Proterozoic-Recent), many enigmatic features of the geologic landscape in Eastern

Jan 1, 1987