Search Documents

In process industries, time-dependent random fluctuations of raw material characteristics and mass flow rates in bulk material or pulp flows cannot be always prevented for different reasons, eg because of the geological situation (no uniform formation of the deposit) or/and because of technological reasons (segregation in bunkers or on stockpiles). Since a long time, there has been practical experiences that such fluctuations can have negative consequences, eg: ò fluctuations of the final products characteristics, ò higher expenditure for process control, and ò worsening of technological characteristics (recovery, sharpness of separation etc). In the literature, there can be found a lot of details as to, eg the improvement of the sharpness of separation in a jig in dependence on the raw material blending (Kubitza, 1981; Gathen, 1983) or the decreasing flotation recovery with increasing raw material characteristics fluctuations in iron and potash ore processing plants (Bubnova, 1978). Up to now, however, these consequences of random fluctuations, eg on the separation efficiency were not predictable theoretically. It could be shown by means of the general model for mechanical macroprocesses (Graichen, 1989), that the reduction of input fluctuations passing a blending facility can be calculated in this way. In this example, the steady state of the process is the wanted one, but, in general, the model is able to describe also non-steady states of the process regarded. On the other hand, the general model of mechanical macroprocesses has been used successfully for modelling separation processes, eg cross-flow and air classification (Molerus, 1969; Neesse, 1991; Senden, 1979; Tichonov, 1973). That is why it was tried to model the influence of input fluctuations on the separation efficiency, that means, the impact of non-steady states - as a consequence of random fluctuations - on a separation process. The models discussed in the literature are related nearly exclusive to the steady state of the process. The reasons for that lie in the (relative) simplicity of the models and the fact that the steady state is aimed at by means of blending processes under practical conditions - because of the advantages mentioned above. These models cited have proved to be superior to other models, since the basic general model for mechanical macropocesses makes possible the consideration of turbulence acting in the process unit and influencing the separation process essentially. This is valid also for modelling the turbulent cross flow classification, applied to mechanical classifiers and hydrocyclones, where the correspondence between the separation characteristics (cut size, separation sharpness) calculated and determined experimentally is much better than for other models.

Jan 1, 1993

By R Sharpe, M D. Hannington, K Perrin, K Simpson, S Petersen, H Gibson, N Augustin, K Lackschewitz, T Monecke

Semi-massive to massive sulfides were drilled in a shallow-water (630 m) hydrothermal system in an island arc volcanic setting at the Palinuro volcanic complex in the Tyrrhenian Sea,Italy. Overall 12.7 m of sulfide minerlisation were drilled in a sediment-filled depression in a water depth of 630 - 650 m using the lander-type Rockdrill 1 drill rig of the British Geological Survey. The longest drill core recovered consists of 4.9 m of continues semi-massive to massive sulfides + sulfates with abundant late native sulfur overprint. Metal enrichment at the top of the deposit is evident in some cores with polymetallic (Zn, Pb, Sb, As, Ag) sulfides overlying more massive and dense pyritic ore. The massive sulfide mineralisation at the Palinuro volcanic complex contains a number of unusual minerals, including enargitefamatinite, tennantite-tetrahedrite, stibnite, bismuthinite and Ag-sulfosalts, that are not commonly encountered in mid-ocean ridge massive sulfides. In analogy to epithermal deposits forming on land, the occurrence of these minerals and the abundance of native sulfur suggest an intermediate to high sulfidation state for the hydrothermal fluids during deposition, implying that the mineralising fluids were acidic and oxidised rather than near-neutral and reduced as those forming typical base metal-rich massive sulfides along mid-ocean ridges. Oxidised conditions during sulfide deposition are likely related to the presence of magmatic volatiles in the mineralising fluids that were derived from a degassing magma chamber below Palinuro volcanic complex. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

British Coal's Selby Complex is the newest producing mine in the United Kingdom. The reasons behind its origins, planning and design are explained. Some detail is given of equipment used, with the emphasis being placed on the unique features of its layout. The entire project has been planned and constructed over many years and the design has consequently changed, principally in response to the geology of the coalfield and improving technology. In spite of many totally unexpected difficulties, the mine, which is not yet in full production, has the highest productivity in the United Kingdom.

Jan 1, 1991

By Anderson D

Investigation of a water inflow into Wongawilli Mine in the Southern Coalfield of New South Wales included algal analysis. The determination of algae in the water suggested an external water source. An alternative hypothesis proposed that algae are inherent in a coal mine environment. Investigations to determine the validity of these hypotheses and provide information on the viability and longevity of algae under adverse conditions were conducted in the mine and the laboratory. Results indicated that a mine environment is not natural to algae and is not conducive to their growth. These findings support the hypothesis of introduction of surface water to the mine workings. They indicate that, in the absence of other available techniques, algae can be an effective tracer for use in the determination of a water source.

Jan 1, 1988

By Osborne V. J, Urbank W

An explosion occurred at Moura No. 4 underground coal mine in Queensland on 16 July 1986 and resulted in the loss of 12 lives. The official report of the accident concluded that the most likely source of ignition was the flame safety lamp. This paper describes an investigation of the behaviour of a flame safety lamp, similar to the one involved in the Moura explosion in atmospheres of methane, coal dust and air, carried out at the Queensland Department of Mines . Testing and Research Station. The behaviour of the lamp is described in conditions of varying methane and coal dust concentrations in air, and varying air velocity. Particular emphasis is given to the 'phenomenon of burning which occurs inside the gauze and which is capable of causing the ignition of an external explosive atmosphere.

Jan 1, 1988

By Yuanping H

There is a practical method of handling methane in a fully mechanized high output coal face when the methane outflow rate from the face is too high to be handled by ventilation alone, a combined method would be adopted. Before adopting this method, above all, the sources of methane outflow, which can be divided into methane in the intake airflow and methane emitted from the working seam and from the worked-out area, are determined by air-methane measure- ments in the tail gate and intake conveyor gate or by air-methane measurements in the working space of the coal face. Then, in

Jan 1, 1988

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

By J H. Heo, J H. Park, M J. Lee

In this paper, the challenging points regarding the high temperature physical chemistry of slags to achieve the improved and stable electric arc furnace (EAF) or electric smelting furnace (ESF) technology on the way to green steel will be reviewed, and the recent experimental and modelling research will be discussed. For example, the initial melting phenomena of hot briquetted iron (HBI) and the slag formation behaviour was observed using a high-frequency induction furnace. Main component of gangue oxides in HBI was SiO2, Al2O3, and CaO in conjunction with unreduced iron oxide. To increase the dephosphorisation efficiency, the distribution ratio of phosphorus between metal and slag was calculated using FactSage™ software, version 8.2 (CRCT ThermFact, Inc., Montreal, Canada) and was compared to the measured results. The optimisation of slag chemistry is required not only for maximum dephosphorisation efficiency with good slag foamability but also for minimum slag volume with less refractory corrosion in EAF process. The slag chemistry is also one of key parameters affecting the operation efficiency in ESF in view of FeO reduction behaviour, viscosity, sulfide capacity, etc.

Jun 19, 2024

This paper will review the experiences of both big and small exploration/mining companies (local and foreign investors), including the impediments to exploration and project development in Indonesia since the Contract of Work was first introduced there (1967 Minerals, 1981 Coal). This is seen through the eyes of a person who has been employed in a managerial capacity in large and small concerns, and more recently as an independent consultant. Comment will be made on the political, legislative and social constraints imposed by the presence of a large group of disparate artisans (illegal miners) who now form a significant component of the Indonesian mining industry; the Bre-X debacle; the impact of the recent Regional Autonomy legislation; and changes to the Mining, Forestry and Environmental Acts. An overall view (including statistics) will be presented as to how recent Indonesian developments have affected international confidence in investing in its mineral sector over the past decade and it will be placed in an international competitive context.

Jan 1, 2004

Nuclear power stations to be installed in Australia will be fuelled from Australian resources of raw materials.This will require the establishment of new manufacturing industries and the eventual expansion of established activities, especially in uranium mining and the preparation of precision metal products.This paper presents some predictions of the possible growth of nuclear power installations in Australia.These might amount to 4000 MWE by 1985 and 11,500 MWE by 1990 and towards the end of the century, about 50 per cent of new generating plant might be nuclear.Predictions are given of the demands for materials (uranium and zirconium) and fuel manufacturing services for four reactor systems which might be considered in the programme.The availability of raw materials and technical capability place Australia in a particularly good position to undertake the manufacture of nuclear fuel; in addition to satisfying the domestic demand we should actively seek export markets for these products.

Jan 1, 1971

By J Champa

The mining industry internationally seems on the verge of a major underground support revolution as suppliers, mines, consultants and researchers develop, test and use thin support (structural) membranes (or superskins as they are commonly called) mainly as a replacement for screen/wire mesh. Thick membrane support in the form of shotcrete (sprayed concrete) has been used since the 1950s in underground mines. Shotcrete, in mines, is generally applied at a thickness between 25 and 100 mm depending on the need. Thin membranes are however applied at a typical thickness between 2 and 6 mm. Certain thin membranes have been available for several years (Tannant et al, 1999), but the intense interest in such supports has only grown in the last few years. The interest lies mainly in the potential to safely reduce the mining cycle time and hence improve productivity. There is however considerable confusion concerning such supports, and this paper attempts to clarify certain aspects and dispel certain misconceptions and myths about thin support membranes.

Jan 1, 2000

By Cunningham CG

Many epithermal gold-silver deposits areknown to occur in the Neogene-Quaternary volcanic complex of the central Andean region of southern Peru, northern Chile, western Bolivia, and north-western Argentina, an area of about 300,000 km2 where these volcanic rocks constitute the dominant cover. Some of the gold-silver deposits were mined during Spanish colonial times, as early as the 16th century,- whereas others were not discovered until the 19th and 20th centuries. The extraordinary gold-silver potential of this young volcanic complex, however, was not recognized until the 1970's when the phenomenal increase in gold and silver prices stimulated new exploration. New discoveries were made, chiefly in southern Peru and northern Chile, of high-grade ores in old mining districts and large low-grade ore bodies, both in old districts and in new areas having no history of mining activity. Many additional gold and silver deposits remain to be discovered within and beneath the young volcanic complex of this region.

Jan 1, 1990

Structurally- controlled deep leaching processes have removed vast quantities of carbonate from a substantial portion of the "silica-dolomite" enclosing the 500 copper orebody. Mine drainage subsequently allowed free access of air to the porous environment created and oxidation of sulphides commenced. During the mIne development stage the exothermic and temperature-dependent nature of these hydrolysis reactions resulted in a slow general elevation of ground temperatures. and levels of 90 - lOO°C were attained in restricted moist sulphide-rich areas.With the advent of production and extensive use of explosives, the oxidation processes were locally raised to new levels of activity. Direct interaction of explosives and sulphides in favourable conditions caused temperature rises to above 260 C. Above this point the dry oxidation of sulphides in air was initiated and rapid escalation to the vicinity of 800 C has been known to occur in isolated cases.Ground reactivity is a function of the complex interrelationship of several controlling factors and no simple index exists.Control techniques are presently aimed at prevention of temperature rises in the range 100 -260 C. Inhibition of the rapid dry oxidation processes above 260 C is difllcult and current efforts have met with only partial success.

Jan 1, 1968

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

By C Xuan, J H. Park, Q Wang, C Shen, D Kumar, W Mu

Dissolution of non-metallic inclusions in the metallurgical slag is of vital importance for cleanliness control of the steel manufacturing. With the development of high temperature confocal laser scanning microscope (HT-CLSM), new insights have been obtained due to its in situ observation characteristics, higher resolution and precise control. However, HT-CLSM measurement has the limitation, eg the slag composition cannot include high amount of transition metal oxides. In addition, it is time consuming for the experimental procedure and not so simple to succeed for every measurement. It is known that digitalisation has made a significant progress in recent years. Machine learning (ML), a sub-domain of artificial intelligence (AI), is the key enabling technology for the digitalisation of the material science and industry. The database for ML model is collected using almost all available HT-CLSM experimental data and subsequently the established database is trained by different ML methods. Unseen data is used as the benchmark of the ML model. Al2O3 dissolution is the main process to be predicted in the current study. A good agreement between the HT-CLSM data and the ML model prediction results show the possibility to apply ML in process metallurgy.

Jun 19, 2024

Geochemical data on Australian granites and pegmatites, and the mineral components of these rocks, are compared with that obtained in similar studies in the U.S.S.R. and elsewhere.The geochemical character of tin granites and the trace chemistry of their component minerals, particularly biotites, have some significance as ore guides in prospecting for tin.The primary geochemical dispersion of tin can be readily tested both in the laboratory and field by colourimetric methods, after volatilization with ammonium iodide, using modifications of the method described by Wood (1958).Secondary dispersions of tin in residual soils or alluvia can likewise be readly tested by rapid colourimetric methods in the field, but simple hydraulic methods, handling larger sample volumes, give reliable outlines of dispersion patterns.INTRODUCTIONThe search for tin ores, whether lode or placer in type, is usually directed on genetic grounds to country within or adjoining acid intrusives.A long established means of prospecting is to test samples for cassiterite by panning or other hydraulic separation.These methods can be used on crushed lode material or the natural materials from placers.With the advent of new techniques for extraction and for colourimetric analysis for tin (Wood, 1958 and Ross and White, 1961) a means is available for rapid analysis of materials not susceptible to quantitative testing by hydraulic methods because of the fine sizings of cassiterite or the occurrence of tin structurally held in minerals. The new methods thus opened up the field of tin prospecting by extending the search for ore guides to genetically associated rocks and minerals, wall ror-ks of veins and a wider range of superficial deposits.

Jan 1, 1963

By Schofield N. A

The cross-sectional method of stope grade estimation at Cobar Mines has consistently had several shoneomings, me most imponant of which being mat stope grade is significantly overestimated in the high grade lenses.The use of mree-dimensional ore lens modelling improved the grade estimation and ore waste definition but significant overestimation still occurred in me high grade stopes, particularly those wim extremely variable grade distribution. The implementation of an indicalor kriging based method for mapping of me high grade copper mineralization has significantly improved the quality of copper grade estimates and provides a mineralisation geometry similar to that generated manually by me mine geologists. This paper presents the results of a test case study in the application of indicator kriging to the mapping of the copper grade in two stopes in the QTS North mineralisation. The results are encouraging in that they prov ide coofi rmation of the geometrical model developed by the geologists and much improved estimates of the grades of me stopes whencompared to me grade reponed from mining these stopes.

Jan 1, 1993

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

Operations at two open cut mines have so far commenced on two out of the five potentially mineable seams in the Fair Hill - German Creek Coal Measures. Due to seam splitting, up to seven mining units are present in the Dysart Seam interval at Peak Downs giving a total of 12 mining units in the section. The coal is low to medium volatile type and produces strong coke. Rank increases and fluidity decreases in the southern part of the area.

Jan 1, 1974

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986