Search Documents

By Y-B Kang, J H. Park, J Park

In order to understand the effect of oxygen injection into the molten metal on the valuable metals (VM) recovery and interfacial phenomena, several high-temperature experiments were conducted using a high-frequency induction furnace with a quartz tube as the reaction chamber at 1673 K. Copper-based waste printed circuit board (PCB) that contains some impurities was selected as the end-of-life resource. CaO-SiO2 based pre-fused slag and oxygen gas were used in present works. The composition change and microstructure of the samples were analysed. As oxygen was injected into the system, impurities were rapidly removed. After the removal of impurities, continuously injected oxygen lowered interfacial tension between liquid slag and liquid metal. Lowered interfacial tension induced Cu loss into the slag.

Aug 21, 2024

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

Results of investigations on adsorption and desorption of CO M CH and a mixture of the two gases are described.4 Results showed that even when the equilibrium conditions contains 50% Co and 50% CH4, the gas emission in the initia' stages will contain as much as 80% CH . 4 The temperature has a small effect and so also particle size for 1.4-11.2mm. The ratio of CO2/CH gases adsorbed in coal samples depends upon t4he equilibrium pressure and this ratio decreases with pressure. Results of field tests support laboratory studies.

Jan 1, 1988

By A D. Campbell

Sublevel caving (SLC) is a mining method adopted in a wide range of mining depths and ground conditions with various layouts adopted to suit orebody geometry. Sublevel caving offers more flexibility and versatility compared to other cave mining methods and is a low cost alternative to open stoping. SLC also has the advantage that stopes are not required to remain stable during production, and no backfill is required. This flexibility combined with increasing pressure on mines to target deeper and lower grade mineralisation has led to increased uptake of the method. The implementation of SLC mining methods across a wide range of mining depths and rock mass conditions has led to ground control practices which vary globally from mine to mine. To date, there has been limited documentation of ground control practices in SLC mining and few benchmarks available in the literature. This paper describes the main findings from a global benchmark of sublevel cave mines conducted over three years as part of the Caving 2040 research consortium. The purpose of the project was to document and compare operational practices, technical aspects and hazard management techniques across SLC mines around the world. The review included 21 mines spread over four continents and 17 different mining companies. This paper provides an overview of geotechnical conditions, challenges and ground control practices at each of the benchmarked SLC mines. Mine design and sequencing practices adopted for ground control purposes and hazard mitigation are provided with case studies. The impact of depth and rock mass conditions on mining productivity and development rates is also described.

Nov 29, 2022

Wrenching between basement blocks is considered to be the mechanism whereby a well developed set of en echelon folds and an associated fracture system are developed in the Fitzroy Depression, Western Australia. The regular geometry of these structures accords with a right lateral regional coupling between high-standing, basement blocks bounding a trough filled with a thick pile of stratified Phanerozoic sediments. The structures developed during or after the Mesozoic Era, but the couple is inferred to have been applied to blocks outlined by old lineaments, which may reflect strains or ruptures in basement that developed during the Precambrian, and which were regenerated during Palaeozoic and Mesozoic time.

Jan 1, 1967

A narrow (200-300m) zone of amphibolite facies metamorphic rocks underlies the Papuan ophiolite near the Musa-Kumusi divide, SW of Popondetta, Oro Province. The amphibolite rocks are bounded up-section, to the NE, by peridotite and gabbro of the ophiolite; and down-section, to the SW, by mafic greenschist, which in turn overlies blueschist facies mafic schists of the Emo Metamorphics.Amphibole compositions within the narrow contact zone show a strong chemical zonation which reflects a steep thermal gradient, with maximum temperatures >800¦C at the peridotite contact. The zonation is recorded in Ti content and A-site occupancy, relative to Al'¦

Jan 1, 1994

The Mesozoic intrusive rocks in southeastern coastal China can be divided into three intrusive suites, and they can be brought into corresponding with four cycles of volcanic activity. This paper describes their time-space relation with volcanic rocks, and their geochemical characteristics. Data from the Mesozoic volcanic-intrusive. complex rocks in Eastern Zheijiang, Eastern Fujiang and Eastern Guangdong show distinct regional differences, both within and tectonomagmatic activity regions. The southeastern coast of China involves four tectonomagmatic activity regions. They have many differences on the nature of magma source regions, activity patterns of magma, time-space distribution, petrography and petrographic facies association of volcanic and intrusive rock and mineralization.

Jan 1, 1990

Tasker (1985) has detailed the accepted practices for constructing polygonal blocks of influerrce in the estimation of ore reserves. Further he suggests that users might fall into traps such as omission or overlap when determining the area of influence for each sample point.As an example of these types of errors Tasker (1985) describes under "Coverage ofthe Area" how 25 per cent of the exploration area will not be included in an equiangular triangular grid where hexagonal blocks of influence are used.The introductory suggestion of Tasker (1985) of "incorrect procedure" by Rudenno (1983) (and Armstrong (1983)) reiterated around the Figure 2a of Tasker (1985), is based on the brief description of the polygonal area of influence by Rudenno (1983). That description is not too different from that given by King, McMahon and Bujtor (1982).

Jan 1, 1985

By L Wsrell

During recent years the iron ore industry has experienced a continuous consolidation trend following increased merger and acquisition activities. Analysing and evaluating these mergers is important in order to establish potential effects. The purpose of this paper is to analyse the price effects caused by the merger between Rio Tinto and North Ltd in 2000. The merger was cleared by the European Commission, as well as the Australian Competition and Consumer Commission, shortly after its announcement. The analysis will be conducted using a simulation model based on a proportionality calibrated almost ideal demand system, which uses the premerger situation in order to estimate the post-merger outcome. The relevant market is defined using shipments data. This is followed by the simulation model applied to the defined relevant market. The results show that the concentration on the market, given by the HHI, increases approximately 15 per cent, and that the market share of the new companyÆs reaches almost 20 per cent. Compared to the CommissionÆs assessment the results indicate a more concentrated market and thus a higher concern for possible competitive effects. Furthermore, the results suggest that the predicted average market price increase from the merger is 1.6 per cent. However, the merged firm is able to increase their average price by 5.1 per cent.

Jan 1, 2005

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

By R A. Bearman

Recent demand pressures for iron ore should not distract from the longer term view that intense competition in the industry has demanded technological innovation of a high order. There is a long track record of successful innovation underpinned by a solid base of scientific research and knowledge. By comment on recent developments in trucks, comminution and direct smelting, this paper suggests that innovation is still a key attribute of the industry. The spending of the minerals industry on underlying science, however, is not particularly high. By looking at other industries we can ascertain that for step change technologies, it is particularly advantageous to have a solid base of science and technology underpinning developments.

Jan 1, 2005

By Groves D. I

The Norseman-Wiluna Belt (Fig.1) is a richly mineralized (production 1900 tonnes Au), Archaean greenstone belt, up to 800km long and 200km wide, which forms the major part of the Eastern Goldfields Province within the Yilgam Block. The Belt evolved ca. 2700 Ma ago as an oblique-slip mobile belt between flanking portions of an older greenstone terrane. Volcano-sedimentary successions in the Belt represent two distinct tectono-stratigraphic associations. Sequences of metamorphosed caic-alkaline intermediate to silicic volcanic rocks interlayered with tholeiitic basalts probably represent the remains of a dissected Archaean volcanic arc (or arcs), and sequences composed dominantly of ultramafic to mafic lavas and intrusions, with minor interflow tuffaceous, sulphidic or cherty sediments are interpreted as remnants of the floor of an ensialic marginal basin (Barley and Groves, 1988). Ultramafic volcanism at Kambalda has been dated at 2692 ¦ 2 Ma (Claoue-Long et al., 1986). The dominantly volcanic associations are locally overlain by coarse clastic sedimentary succes- sions. The Belt is also typified by major north- to north-northwest-striking fault systems, shear zones, and tectonic lineaments, many of which are traceable for more than 300km. As well as defining the boundaries of the belt, these structures have accomodated much of the regional strain and acted as conduits for hydrothermal fluids during deformation, metamorphism and mineralization. As a result, most of the epigenetic gold deposits in the Belt occur in subsidiary structures related to these fault systems (Eisenlohr et al., 1988). Deformation involved oblique compression resulting in a closely spaced network of low-angle faults (thrusts) as well as upright folds and oblique- to strike-slip faults (Archibald, 1987; Veamcombe et al., 1988). This was accompanied by regional metamorphism and granitoid emplacement. At Kambalda, regional deformation and metamorphism were synchronous with the emplacement of the Kambalda Granodiorite which has been dated at 2662 ¦ 4 Ma (Hill and Compston, 1986), approximately 30 Ma after volcanism.The tectonic history and style of deformation of the Norseman-Wiluna Belt are similar to those of Phanerozoic oblique- slip mobile belts at continental margins, which are also a major source of hydrothermal gold mineralization.

Jan 1, 1988

A Modelling Approach Using a Back-Calculated Induction Time to Predict Recoveries in Flotation

Sep 13, 2010

By A Purwodihardjo

Evaluation of the construction method used for the pedestrian underpass construction at Ipswich Road, Brisbane, Australia is presented in this paper. The pedestrian underpass was constructed through the existing railway embankment between Harrogate and O’Keefe Streets on the eastern side of Ipswich Road. This underpass construction is part of the CLEM7 tunnel project (formerly known as the North-South Bypass Tunnel) which is the longest toll road in Australia at a total length of 6.8 km. The jacked box construction technique was initially identified as a preferred option during the tender and concept design phases. However at the final design stage, the cut and cover technique was selected as this method can reduce the construction time and cost significantly. The design and construction teams effectively managed the challenges, complexities and risks associated with undertaking cut and cover tunnel through the existing heavily utilised rail embankment. The on-site construction time for the underpass using the cut and cover technique was reduced to less than 42 hours.

Mar 8, 2011

By Sivell W

We discuss the origin of the Patuki ophiolite complex and the Dun Mountain ultramafics of Middle Permian age in Nelson, New Zealand. It is shown that the Patuki volcanics have strong affinities with tholeiites of mid ocean spreading ridges transitional to alkaline basalts similar to those from fracture zones and ocean islands. At D'Urville Island, typically pillowed alkaline basalts enriched in rare light rare earth elements (LREE) - ophitic spilites - are associated with LREE-depleted (N-MORB-like) tholeiitic spilites with intergranular textures. The metabasalts are associated with a wide variety of sediments, and with sediments are intruded by conformable sheets of serpentinite. Coarsely crystalline mafic and plagiogranitic rocks signify vents and magma chambers, and we propose that the group developed as ocean crust from a slowly spreading mid-ocean ridge, transform association, overwhelmed at intervals by volcaniclastic sediment. Detailed mapping at a scale of 1:5000, and stratigraphic and geochemical development and structural coherence, show that the group is not melange in the Franciscan sense. The Dun Mountain Group, of serpentinites, peridotites, dunites, gabbros and other rocks, intruded the upper Patuki Group as a linear series of aligned pods and sheets. They carried up with them tectonic inclusions of older rock, which were metasomatised, and altered wall-rock, and one low angle dike passed several hundred metres into overl~ing sediment, at moderate temperatures (500 C). The rocks did not act as a floor (and alleged source) for the Patuki, but partly post-dated and were emplaced into Patuki.

Jan 1, 1987

By J B. Collier, R M. Fraser, O Dahl, I M. Platten

Grade control is a process of maximising value and reducing risk, through the delivery of quality tonnes to the mill via the accurate definition of ore and waste. It essentially comprises data collection, integration and interpretation; local resource estimation; stope design; supervision of mining and stockpile management. The foundation of all grade control programs should be that of geological understanding led by high-quality mapping and sampling to drive appropriate estimation strategies and mining. Gold veins show various complex features relating to erratic grade distribution (nugget effect), variable geometry and internal architecture. These include variations in dip, strike and width, late-stage faulting/shearing effects and geometallurgy. Such variations generally require close geological understanding to ensure optimum grade, minimal dilution and maximum mining recovery. A well designed grade control program will prove to management and stakeholders that by applying geological knowledge, the mining process can be more efficient and cost effective. This paper reviews the issues of grade control in underground gold mines and focuses on integrated mapping and sampling through three case studies.

Jan 1, 2009

The metallurgical testwork program is generally the most important critical path item for the completion of a bankable feasibility study and hence can become the critical parameter for financing of potential mining projects. This paper presents generic detailed testwork programs suitable for bankable feasibility studies for a gold leaching and polymetallic flotation study. The design of the metallurgical testwork program for each of the two differing processes is discussed and the critical factors that effect the selection of the testwork programs are highlighted. The importance of the metallurgical testwork results in predicting the metal recoveries and cash flow prediction for the project is presented. The detail of the testwork programs costing is broken into activity based methods based on the laboratory and management hours/costs, such that generic rule of thumb costing guidelines can be generated. The scheduling, costing and importance of the metallurgical testwork program to process feasibility studies are discussed in this paper.

Jan 1, 2000

By Shinnosuke U, Zhang HE, Qian X

In this paper it is recommended that pyrite is to be separated as froth from arsenopyrite by selective depression of arsenopyrite in strong alkaline medium (1), by oxidation with chlorinated lime (II), by co-use of chlorinated lime with sodium carbonate (III), and by modification with `L' reagent (know-how) without filtering to get rid of residual copper ions after Cu activation (IV). The corresponding principles of these (new) effective methods were briefly discussed. The artificial mixture (1:1) of pyrite and arsenopyrite could be successfully separated, and concentrates of pyrite containing 2.12 per cent (I), 7.00 per cent (II), 2.60 per cent (III) and 3.16 per cent (IV) arsenic with recovery of 90.9 per cent (1), 89.5 per cent (II), 89.0 per cent (III) and 81.4 per cent (IV) respectively can be obtained by only one flotation. Some effective precautions were suggested to improve the separation of arsenopyrite and pyrite (or other sulphides) by flotation.

Jan 1, 1993

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By B Petrie, D J. MacKenzie

The Macraes mine is producing 175 000 ounces Au/year from a mesothermal deposit with total resource of at least five million ounces. The deposit is hosted in greenschist facies Otago Schist, a widespread Mesozoic metasedimentary sequence that forms the basement of the South Island of New Zealand. Mineralisation was controlled by a late metamorphic shear zone which had both brittle and ductile structures accompanying mineralisation. The shear zone dips shallowly (about 15¦), subparallel to the shallow-dipping regional foliation, and mineralization occurred during southwesterly-directed thrust motion. Mineralisation occurred under greenschist facies conditions (about 350¦C) during uplift of the Otago Schist in the late Jurassic. No syn- or late-metamorphic igneous bodies occur within the schist belt. The hosting shear zone is up to 120 m thick, and is traceable for more than 30 km along strike. The shear zone is truncated by an underlying low angle normal fault that juxtaposes mineralised lower greenschist facies rocks on to unmineralised upper greenschist facies rocks.

Jan 1, 2004