Search Documents

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

The high-shear colloidal mixer is generally recognised as the most efficient method of mixing cement based grouts. Only recently however has this technology been applied to the production of cemented rockfill (CRF) for use in underground mines in North America. Traditionally, paddle type mixers have been used to produce the cement based slurries required for the preparation of CRF. While considerable success has been achieved with these mixers, tremendous advantages are attained with the colloidal mixer. The combined effect of the highly efficient mixing action and the ability to mix low water/solids ratios, allows for reductions in the cement content for a given strength requirement. Cement can also be replaced by cheaper fillers such as flyash, resulting in further cost savings. Although large-scale dedicated CRF batching plants are typical, there is a growing need for mobile plants capable of operating anywhere underground. The compact size and rapid batching speed of high-shear colloidal mixers has allowed them to be incorporated into skid mounted systems capable of producing and discharging cement based slurries onto rockfill aggregate for the production of CRF. In many cases run-of-mine development waste can be used as CRF aggregate with these slurry plants thereby reducing the cost of waste rock removal. These relatively low cost portable plants have now allowed several mines to economically recover isolated pillars and realise positive returns on their investment.

Jan 1, 1998

A new porphyry copper gold district has been discovered at Goonumbla near Parkes in central New South Wales. Endeavour 26 North is the largest deposit known to date with a possible resource of 166.4 million tonnes at 0.74% copper, 0.12g/tonne gold and 1.7g/tonne silver, using a cut-off grade 0.3% copper. Mineralisation is primarily bornite in the higher grade zones and chalcopyrite in the peripheral lower grade zones. Most of the copper, gold mineralisation is associated with potassic alteration. Two mineralised quartz monzonite porphyry intrusive stages have been identified and these are related at depth to a large monz- onite stock which may have been the source of some of the mineralisation. On the basis of detailed paragenesis studies, the potassic zone can be divided into three symmetric subzones. The low grade inner potassium feldspar subzone is confined to the later intrusive porphyry. The outer potassium feldspar subzone is the most highly mineralised alteration halo due to the focussed superimposition of two hydrothermal cycles which have overprinted intrusive and volcanic rocks. The fringing biotite potassium feldspar subzone reveals alteration minerals which are developed early in the paragenesis. Fracture controlled quartz sericite alteration with low sulphide content, fringes and, in part overprints the potassic zone. The restricted pipe-like nature of the alteration zones and related mineralisation suggests that Endeavour 26 North is repres- entative of a multiphase focussed porphyry copper gold system.

Jan 1, 1986

The discovery of gold mineralization at the Manhattan mercury mine, Napa and Yolo counties, California in 1978 was the result of applying a new exploration ore deposit model in a region previously unprospected for gold. This discovery, the McLaughlin gold mine, owned and operated by Home-stake Mining Company, is a classic epithermal mercury-hot springs-gold deposit currently producing approximately 7,776,000 grams of gold annually.The exploration program that led to this discovery was based on a mercury-hot springs-gold genetic model. The model was developed using basic knowledge of ore-forming processes plus careful field observations made during examination of many known precious metal districts in. the Western U.S.A. Theoretically, hot spring systems could host gold deposits and, indeed, gold in these environments had been recognized for years. However, at the time of the McLaughlin discovery, it was not known to occur in sufficient quantities to inspire geologists to explore hot spring systems specifically for gold. Field observations recognized the presence of hot spring deposits and mercury mineralization asso-ciated with precious metal districts, (Bodie, California being a type example), and this associ-ation prompted the development of a hypothetical model. Subsequent exploration activities were directed towards the examination of mercury mines and prospects as potential targets for gold deposits. The model envisioned hot spring deposits (sinter) containing mercury mineralization at the surface with anomalous gold values grading downward into significant ore grade gold values.

Jan 1, 1990

By P J. Harris, D J. Bradshaw

Surface oxidation of sulfide minerals, such as that found in the regions of a sulfide ore body near the water table, can have a significant impact upon flotation. This theme has been explored for Merensky ore type sulfides where an ore containing pyrrhotite, pentlandite and chalcopyrite was thermally oxidised and the role of potential remedies investigated. Back-scattered scanning electron microscope images are presented showing the oxidation layer which formed in the mineral surfaces. These oxidation layers were depleted in both sulfur and iron with incorporated oxygen. Flotation recovery rapidly decreased with increasing oxidation, particularly after 27 days and reached a plateau after 50 days. Up to 27 days, this effect could be partially overcome with higher collector additions. Oxidation had more impact upon the finer size fractions, particularly for pyrrhotite. For more heavily surface oxidised samples, ultrasonic treatment prior to collector conditioning was found to improve flotation recoveries. This treatment had the greatest effect upon chalcopyrite particles. Sulfidisation was successful in restoring the flotation recovery of the heavily oxidised sulfide minerals. Longer sulfidisation conditioning times were not conducive to good flotation recoveries of both oxidised pyrrhotite and pentlandite due to oxidation of the freshly formed sulfide surfaces. For maximum flotation recoveries of oxidised pyrrhotite, pentlandite and chalcopyrite, different sulfidisation conditions are indicated. It appears likely that in a mineral processing operation treating oxidised Merensky type ores, two stages of sulfidisation employing different conditions would be required.

Jan 1, 2005

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

By Storey AG

Following initial plant scale work on the development and performance of 'spray' oil lances, a full scale room temperature model of the blowpipe-tuyere region of a blast furnace was built to study the basic aerodynamic features of auxiliary fuel injection procedures. Mobilwax 2305 was used as a substitute for Bunker C oil fuel in view of its similar physical properties and the fact that the atomised droplets could be frozen in flight and size, distribution analyses made for various operating procedures. It was shown that secondary atomisation processes far outweighed the importance of any primary atomisation procedures in determining mean Sauter Diameters particularly at high windrates typical of current blast furnace technology. It was also found that good spray dispersions across the blow pipe could only be obtaind for liquid fuels and that the lateral rate of spray dispersion was substantially enhanced by primary atomisation procedures. Mean particle diameters of sprays were found to be predictable on the basis of elementary stability theory and fell within the size range necessary for good combustion at all liquid fuel rates studied. The possible effects of high oil injection rates on flooding phenomena in the furnace bosh were considered. Comparisons show that high oil rates can lead to significant increases in the hanging factor (e.g. 'V 10% at 135 kg oil/thm) owing to increased gas flow rates/thm resulting from the presence of hydrogen.

Jan 1, 1975

By G Hayes

Ore from the Browns deposit near Batchelor, in the Northern Territory of Australia, is a fine-grained polymetallic sulfide ore hosted in graphitic black shale. Minerals of economic significance are seigenite (Co,Ni)4S3, Galena (PbS) and Chalcopyrite (CuFeS2) with minor Sphalerite (ZnS). Gangue minerals include quartz, carbon and K-feldspar. The grain size is fine, with a significant amount of the seigenite present as Early flotation work determined that a grind size of around 20 microns was required to achieve clean sulfide concentrates. This work recommended oil agglomeration flotation, in which small sulfide minerals were collected, then loosely agglomerated with oil ahead of flotation into a heavily mineralised froth. In the 400 kg/hr prototype plant this froth proved unmanageable. A conventional flotation circuit after grinding to a P80 of 24 microns and using very low flotation pulp densities resulted in an 86 per cent cobalt recovery.The paper analyses further laboratory work which has increased cobalt recovery to 91 per cent by grinding to û250 microns ahead of flash flotation. The real cobalt recovery breakthrough comes from flash flotation of the whole mill discharge rather than the more usual flash flotation of cyclone underflow. Flash flotation tailings are ground to û38 microns and are floated under normal flotation conditions with only the scavenger concentrates being reground to 20 microns.A one tonne per hour prototyping campaign is scheduled to demonstrate the robustness of this circuit.

Jan 1, 2002

By A Radici, S Russell

The Dampier Port Upgrade was completed in 2007 and is the largest project in Rio Tinto Iron Ore's expansion program. The project doubled Dampier Port's iron ore shipping capacity over a five year period. Sinclair Knight Merz (SKM) was appointed by Rio Tinto as the Engineering, Procurement and Construction Management (EPCM) contractor to manage Phase A and Phase B of the Dampier Port Upgrade. The aim of the project was to increase the Dampier Port capacity from 74 to 140 million tonnes per annum (Mt/a). This increase in shipping capacity tripled the capacity of the Parker Point facility from 34 to 94 Mt/a, whilst the East Intercourse Island facility increased from 40 to 46 Mt/a. The Dampier port remained fully operational throughout construction and achieved record yearly export tonnages over the period of the project. The $US1.4B project was completed ahead of schedule, on budget and with an outstanding safety record. Significantly the project team set an industry benchmark by achieving five million man-hours Lost Time Injury (LTI) free. The project has been recognised by the Engineers Australia 2008 Western Australian Engineering Excellence awards as category winner in resources and the overall winner in WA, and went on to win a National Engineering Excellence award. This paper provides an overview of the EPCM project management and an insight into some of the key drivers that have delivered this outstanding project.

Jan 1, 2009

Underground equipment owners and users in order to compete and succeed in being viable business propositions must continually balance costs with productivity. By reducing their hourly ownership, operation and maintenance costs and increasing their hourly production, the cost per unit of material mined will be optimized.

Jan 1, 1990

By J Temos

This paper outlines a number of immediate practical approaches to continuous improvement in environmental management in the minerals industry. It puts these into context with longer time-frame step-change approaches whose gestation may take a decade. Examples of improvements and approaches are drawn from WMC operations.

Jan 1, 2002

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

By Tomlinson R. C

The paper will briefly describe planning in the National Coal Board (NCB) and the contribution that operational research makes to it. It will then give details of some of the models in use and will finally consider critically the problems of looking ahead to the next century.

Jan 1, 1977

In recent years the use of directional drilling has become increasingly popular in several applications. These include shaft pilot holes, exploration drilling, mine service holes and drilling beneath surface structures and obstacles. The prime objectives are to increase accuracy and reduce time, cost and environmental disturbance.

Jan 1, 1992

By Williams P

The assumptions made in conventional (Terzaghi) consolidation theory are not met in a tailings deposit. Finite or large strain consolidation theory must be employed. The paper describes such a consolidation model and its application to the design of tailings impoundments, water management systems, and long term rehabilitation.

Jan 1, 1990

By Drinkwater DJ, Watsford RMS, Johnson NW, Munro PD

This paper describes the use of modelling and simulation techniques in the analysis and optimisation of grinding circuits at the Lead/Zinc Concentrator of Mount Isa Mines Limited.The objectives of the studies were to: -1. improve primary grinding circuit performance by reducing the production of -0.006 mm galena fines.2. maximise the fineness of grind in the second existing grinding power and pumping capacitie The study has shown that quantitative models can operations. The models described plant operation,,and simulated the effect of process changes on plant performanc The use of automated scanning electron microscope technology tcliberation characteristics of the major minerals in the Mount isa Lead/Li ore is also described.

Jan 1, 1985

Lihir Gold Mine is situated in a dormant volcanic caldera on a small island off PNG. Not æextinctÆ but dormant. Current ground temperatures are up to 150 degrees Celsius with active geysers in the workings of the mine, pools of boiling ground water adjacent to low-grade dumps and hydrogen sulphide gas emissions. It is a unique mining environment by world standards. This paper will deal with the following issues encountered and managed by the operation:blasting in hot and reactive ground; management of sulphide gas emissions; disposal at sea of all mining waste rock; one dear to all Australian minerÆs hearts û dealing with landowner groups; and unusual human resource issues.

Jan 1, 1999

By D François-Bongarçon

The link between geostatistics and Theory of Sampling (TOS) is examined again in view of new findings made while trying to compare predicted sampling variances and estimated grades (using geostatistics) on the same material, and this provides an important consistency requirement whenever calculations are made that involve both theories in a comparative way. It also briefly explores the relationship to De Wijs fractal model of mineralisation and eventually provides new support for the use of consistency theory for calibrating TOS variance formulas.CITATION:François-Bongarçon, D, 2017. Theory of Sampling and geostatistics – the ultimate link, in Proceedings Eighth World Conference on Sampling and Blending , pp 391–394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By B P. Banerjee, S Raval

In the recent past there have been dramatic advancements in the development of remote sensing platforms (satellite, aircraft and unmanned aerial vehicles – UAVs) as well as sensor systems (multispectral, hyperspectral, thermal, light detection and ranging (LiDAR) and radar). However, selection of the appropriate remote sensing technique for a mining application is complex and requires scrutiny on multiple scales including spatial, temporal and imaging capabilities. This presentation highlights various conventional and emerging remote sensing approaches over a mine’s life.CITATION:Banerjee, B P and Raval, S, 2016. Applications of advanced remote sensing systems during a mine life, in Proceedings Life-of-Mine 2016 Conference , pp 116–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

It is important to prevent the overload ing of mills being operated near maximum tonnage. Changes occurring during overload differ in their usefulness as guides to control action. The Primary Ball Mills of Bougainville Copper Ltd. provide an example of some of the problems and progess in avoiding overload.

Jan 1, 1978