Search Documents

By G C. Lukey, J S. J van Deventer

The disposal and subsequent encapsulation of mine tailings in a cost-effective and environmentally secure and responsible manner is one of the principal issues facing any modern mining project. A careful assessment of all options available for the capping and subsequent remediation of tailings is important because it can result in large capital, operating and closure cost-savings. For these reasons, the technology of geopolymerisation is receiving increasing attention for the stabilisation and solidification of waste materials produced from mining operations. The first part of the current study investigates the application of geopolymer technology to the capping of hypersaline mine tailings. It has been found that suitable geopolymeric materials which have satisfactory compressive strength, durability as well as low permeability, can be formed using between 60 - 75 per cent of mine tailings as the main ingredient. It has been established that geopolymeric materials have the ability to suppress dust generation and prevent salt precipitation on the surface of the mine tailings. The slurry-like consistency of geopolymers would promote efficient application procedures through established tailings disposal techniques. This is a possible close-out technique for hypersaline tailings storage facilities such as those commonly found in Western Australia, which meets both regulatory requirements and community expectations. The immobilisation of contaminant metals within geopolymers has been investigated in the second part of the present study. In particular, the leaching characteristics of Cu and Pb from geopolymeric matrices derived from different fly ash sources have been examined. Potential breakdown of each geopolymer containing metal contaminants due to the leaching of Si and Al from the geopolymeric matrix has also been investigated.

Jan 1, 2000

Evidence for Middle-Late Triassic large-scale, silicic volcanism characteristic of extensional continental terranes is widespread in the Tasman Orogenic Zone in Eastern Australia. Detailed study of an area of south-east Queensland has defined the eroded remnants of a large collapse caldera and an associated area of rhyolite dome building and regional downsag which may be a second caldera (Stephens, 1986). The silicic volcanics and minor basaltic to andesitic products have been assigned to the Aranbanga Volcanic Group (Cranfield, in prep.) and the associated granite complex has been named the Mungore Complex (Ellis, 1968). Published isotopic age dates on the Mungore Complex are 212-219 m.y. (K-Ar Biotite; Ellis, 1968) and 226 m.y. (pooled Rb-Sr on several similar plutons in the region; Webb and McDougall, 1967). Basalts within the area have been dated at 219 m.y. (GSQ Annual Rpt., 1986). The collapse caldera (Mungore Caldera) lies on the intersection of 4 major structural features: 1) the Mt. Perry Lineament, a meridional fault zone extending for over 600 kilometres in a NNW-SSE direction and which has faulted the eastern part of the caldera 5 kilometres sinistrally. The lineament has been active at least from mid-Permian to Late Triassic and has localised activity into the Tertiary. Granite plutons of the same age as'the Mungore Complex- are topographically prominent and largely concentrated east of the Mt. Perry Lineament and its extensions (Nash, 1986); 2) the extension of the Darling River Lineament, a continental-scale, ENE trending feature which correlates with regional structural discontinuities but which lacks expression as faults within the Tasman Orogenic Zone;

Jan 1, 1987

The management of safety has undergone a number of radical changes in the past 100 years. The most important paradigm shifts occurred through the work of Heinrich, followed by the advent of the safety systems era and, more recently, the behavioural safety approaches that have become increasingly popular around the world. Each of these æapproachesÆ to safety has left an indelible mark on the way we target safety improvements, helping decide which interventions are deployed and how they will be measured. They have also resulted in a number of æmythsÆ about safety management, each of which will be discussed, analysed and challenged in this paper. This paper highlights the complex problem of æcomplacencyÆ, that has arisen out of the increased levels of regulation and consequent perceived protection that workers enjoy in the work place. It also looks at a phenomenon called æaccident migrationÆ which results from a superficial treatment of accidents with changes to rules and procedures. The most recent approach to safety is generally known as behaviour-based safety, which flowed from the human sciences and quality management era. This approach has had a dramatic impact on the way safety is managed around the world, but still falls short in a number of key aspects, most notably the area of risk awareness and risk understanding. Many workplace accidents occur simply because the risk is unidentified, underestimated, not understood or ignored. This paper proposes a new direction for safety, called competency-based safety. It is based on cognitive psychology aimed at combating the consequence of modern protection. A case study is presented detailing the deployment of this approach throughout Placer Dome.

Jan 1, 2005

By S Vink, V Nanjappa, C J. Moran

Poor quality water resulting from interaction of surface run-off with saline mine spoil and soils can cause significant problems for water reuse on mine sites. Not only can this saline water lead to machine corrosion and increased maintenance costs, but may cause detrimental effects on the environment. Determining the geochemistry of mine spoil, and the likelihood of salt dissolution during rainfall events, may aid in more effective mine site management of water. Spoil samples were taken from three areas of the German Creek mine site, situated in the Bowen Basin coalfield, Queensland. Samples from two undisturbed areas on the lease were also collected for comparison. Analyses were performed using a variety of laboratory techniques: leaching tests, effective cation exchange capacity determination, X-ray diffraction, clay quantification, and total organic content determination. Results show that dissolution of surface (top 2 cm) salt minerals from spoil areas is an important contributor to surface run-off salinity during rainfall events. Equally, ion exchange with clay minerals appears to be a significant source of elevated ion concentrations in run-off waters. Findings from the undisturbed areas show undetectable quantities of salt mineral species, resulting in waters with low ion concentrations. More generally, monovalent cations (sodium, and to a lesser extent potassium) appear to be derived from dissolution of salt precipitated whereas divalent cations (calcium, magnesium) are more likely to be sourced from exchange reactions with clay minerals. Incorporating knowledge about the mechanism of cation mobilisation from spoil with the spatial distribution of spoil properties and understanding of the dynamics of water quality variations on the site will aid in development of integrated water quantity and quality management strategies.

Jan 1, 2009

Environmental leaching methods such as the toxicity characteristic leaching procedure (TCLP) test or the ASLP test are used to assess wastes including mining and mineral processing by-products. These tests were initially designed as regulatory tests simulating conditions in a co-disposal municipal landfill waste facility and do not allow leaching performance to be predicted in site specific scenarios. Further, the assumptions underlying these tests tend to define worst-case scenario leaching conditions for by-products from the mineral industry disposed of outside a co-disposal scenario.   Recently some characterisation leaching test methods have been issued as ISO/TS standards (ISO/TS 21268-3:2007 and ISO/TS 21268-4:2007) that aim to define the leaching performance of soil type wastes and to predict the leaching performance of these wastes over long time frames. In this preliminary work these standards are trialled for by-products from the mineral industry and the quality of information that can be obtained from them compared to TCLP/ASLP tests.   Where clear comparisons were possible, the TCLP/ASLP tests were typically found to extract a similar, or often greater, amount of component than (i) tests conducted at the same pH but without the acetate buffer or (ii) for test conditions aimed at simulating long-term leaching in an eluate defined by the waste type. While further work is required, the preliminary results indicated that the tests may provide reliable long-term estimates of leaching performance of wastes in soil types of variable pH and provide a suitable basis for long-term planning for optimal waste handling, treatment or even re-use.

Jun 1, 2010

By J B. Farrow

The AJ Parker Cooperative Research Centre for Hydrometallurgy carries out research on behalf of, and in collaboration with, the Australian mining industry. As might be expected, much of its research is directed towards improving the efficiency of alumina and gold processing plants. However, the Centre also carries out research of relevance to base and other metal producers. A key element in its work is the successful transfer of its technology to the companies with which it is working. In general, this is achieved in the following five steps:definition of the problem through discussions with the company commissioning the research; execution of the research; assessment of the research findings; testing of the research findings by pilot plant or on-site trials; and implementation of the results on the full-scale. This pattern is exemplified by the work carried out by the Centre to improve the performance of gravity thickeners which are used throughout the minerals industry for solid-liquid separation. The research has focussed mainly on ways to optimise the use of flocculants (long chain polymers) to enhance thickener performance. It has been shown that the way the flocculant is mixed with the slurry is of profound importance. Computational fluid dynamics modelling of the feedwell region of thickeners and laboratory and plant flocculation studies have been used to determine better ways to contact the flocculant with the feed slurry. Implementation of these and other findings on the full-scale confirmed that improvements in thickener performance were indeed possible. As a result of this AMIRA funded thickener technology work, there have been considerable savings to a number of Australian mineral processing companies, through improved operation, higher throughputs and flocculant savings.

Jan 1, 2000

By M Kuruppu, B Besa

Currently, conventional methods of decline development put enormous cost pressure on the profitability of mining operations. This is the case with narrow vein orebodies where current methods and mine design of decline development may be too expensive to support economic extraction of the ore. The time it takes to drill, clean and blast an end in conventional decline development can be up to 473 minutes. This is because, once an end is blasted, cleaning should first be completed before drilling can commence, resulting in low advance rates per shift. Improvements in advance rates during decline development can be achieved by application of the electric monorail transport system (EMTS) based drilling system. The system is composed of a two-boom drill mounted on the monorail and a pneumatic face cleaning system that loads blasted material into monorail containers. The operation allows for drilling of the top part of the face to commence as the monorail loading system continues to clean the blasted material at the development face. The preliminary indication is that an advance rate of 12 m per day could be achieved compared to 6 m per day in conventional decline development. The increase in the advance rate results from increased number of blasts that are possible per shift due to reduced time of cleaning and drilling the development face. The continuous drilling system has the advantage of accelerated decline development and orebodies will be accessed quickly and cheaply. Other advantages of the system include negotiating steep and changing gradients (ie reducing decline length), ability to negotiate tight horizontal curves, small operating room and limited diesel fumes.

Jan 1, 2008

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

By A D. T Goode

Data Metallogenica (DM) is unique as a global mineral sample collection and deposit database with over 70 000 rock samples and a wide range of descriptive, photographic and measurement data. Subscribers have access to approximately four gigabytes of on-line data with many examples included on the public pages. DM commenced its life on the Pacific rim in 1971 and much recent growth has focused on countries of the Pacific margin, particularly Australia, Fiji, Chile, Indonesia and Peru. Approximately 600 separate deposits and mineral occurrences in this region are represented in DM. The sets of rock samples have been photographed at high resolution and included on the web site, together with unpublished descriptions, deposit cross-sections, bibliographies, field and mine photographs, petrology and reflectance mineralogy. Figures and abstracts from PhD theses are a new addition and the donation of proprietary databases by companies and individuals is an encouraging trend. DM increasingly is being viewed as an acceptable and important repository for æfragileÆ and irreplaceable personal and company data, it is also being recognised in its true light as a high level information system, not solely a collection of rock samples. Data Metallogenica is a not-for-profit venture of AMIRA International that requires self-funding from December 2004. Growth and development must be funded entirely out of subscription and sponsorship revenues because no government subsidy is provided. The Pacific rim is in the mainstream of mining and exploration activities worldwide and those involved have much to gain from a dynamically sustaining DM. The home page at www.datametallogenica.com contains much example data and details of subscription and membership rates.

Jan 1, 2004

During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within North America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The traditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

Jan 1, 2005

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Grant J

In surface mining, significant improvements in efficiency can be obtained through greater control over the formation of the muckpile. By tailoring the muckpile shape and its looseness to the requirements of the excavating equipment savings can be rea- lised through increased production, machine life and reduced maintenance. For instance, one open cut coal mine has recently estimated that a 2001o improvement in its front row throw would realise $320,000/year savings in rehandle costs alone. Previously greater throw has been achieved by increasing the powder factor through increased quantity of explosive or by drill- ing a larger number of holes-both at a significant cost penalty. However a recent series of experimental blasts demonstrated that it was possible to achieve a twofold increase in the distance of throw of a single row blast by simply changing delay timing alone. The Nobel Electronic Delay Detonator was used to provide the timing flexibility and control required for a thorough study of the effect of blast timing on heave. Whilst it is well accepted that the front row of a blast dominates the extent of throw, it was also found that the profile of the blast could be significantly altered. To date, the general consensus has been that the muckpile for- mation from a blast is a function of the blast geometry, the rock type, the explosive and the initiation sequence. Typically the geometry, rock type and initiation system have a far greater impact than the explosive type. This has been demonstrated by many high speed film studies. However the extent of influence via initiation has rarely been fully evaluated, owing largely to the limited control offered by conventional detonators.

Jan 1, 1988

By D Macklin, R Hammond, T G. Blenkinsop

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Base metal sulfides at the Currawong volcanic-hosted massive sulfide deposit in the Lachlan fold belt of Victoria, south-east Australia, were formed in the late Silurian, but D2 deformation of the deposit in the Devonian Bindian orogeny was responsible for structural repetition that created the resource. The primary sulfide lenses were stacked by reverse-sense shear zones within a volcano-sedimentary sequence dominated by dacitic intrusions and turbidites. Shear zones were localised along lithological contacts, including the margins of the sulfide lenses. The competent dacitic intrusions did not fold during D2; folding was restricted to the packages of metasedimentary rocks. Overturning occurs within, but not between, the metasedimentary packages. The overall geometry of the deposit is that of a duplex, but the detailed shape does not conform to idealised duplex types, probably because of post-D2 deformation. A significant complicating factor for understanding the deposit, and for resource evaluation, is the dramatic variation in deposit geometry along strike, which may also be due to post-D2 deformation. The present day configuration of the deposit results from constructive thrust repetition of what may have been a single ore lens and destructive along-strike disruption controlled by rheology.CITATION:Blenkinsop, T G, Macklin, D and Hammond, R, 2015. Rheological controls on the geometry of the Currawong volcanic-hosted massive sulfide deposit, Lachlan fold belt, Victoria, south-east Australia, in Proceedings PACRIM 2015 Congress, pp 469–474 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Mineral resource and ore reserve classification defines the risk associated with quoted resource tonnes and grades, allowing the interested party to make a judgement as to the `worth' of the resource statement. The JORC Code and Guidelines (1992) are now well entrenched as the foundation upon which gold and base metal deposits in particular are publicly reported. There are three categories of resource, namely Measured, Indicated or Inferred reflecting decreasing levels of confidence. The ore reserve, that is the economically mineable part of the resource, is classified as Proven or Probable and can only be drawn from the Measured and Indicated resource categories. As summarised by Stephenson (1995), resource/reserve classification has been an issue ever since the earliest days of mining in Australasia where, like elsewhere in the world, the industry, for a long time, lacked firm reporting guidelines. Those currently adopted in Australasia as the minimum standards for companies reporting to the Australian Stock Exchange (ASX) have been developed and revised since 1972 by The Australasian Institute of Mining and Metallurgy (The AusIMM), the Australian Institute of Geoscientists (AIG) and Australian Mining Industry Council (AMIC). Debate is now underway in terms of adopting an international code. The Code specifically does not attempt to regulate either the classification technique nor the method of estimation of the resource/ore reserve, but rather places the responsibility for this task on a `Competent Person' whose experience will decide the appropriate approach for a given commodity/orebody. The Competent Person must be a Corporate member of either The AusIMM or AIG with five years experience `relevant to the style of mineralisation' under consideration.

Jan 1, 1996

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987

By G Billing a, D Gribble, E Hall, D Varga

The theoretical benefits of electronic detonators have been reasonably well documented. To support this, a practical comparison was made between the performance of the standard shock tube system, NONEL, and a high precision electronic system, HotShotÖ, at the Sunrise Dam Gold Mine. The expected benefits from electronic detonators to Sunrise Dam were identified prior to the trial. Based on these, a number of objectives were set to demonstrate the value of the HotShot system. These are an improvement in fragmentation leading to an increase in productivity, less oversize rehandling, increased throughput and more uniformity in muck pile movement. To maintain the integrity of the trial, the nominal timing of the shots was kept exactly the same, thereby restricting any performance improvements to the precision of the electronics. Accordingly, adjacent shots were chosen with consistent geology. Video footage was taken of the blasts and vibration monitoring was carried out by fixed geophones throughout the mine. Spot heights of the muck pile swell were taken immediately after the blast and heave profile graphs were generated for comparison. Video footage was taken for a period of three hours for both shots to analyse cycle times of the excavator and trucks. PITRAM data was also collected for analysis. As far as practicable, the ore was taken to the same finger on the run-of-mine (ROM) pad to assist in single sourcing for the crusher and to allow oversize to be separated out. From specific metrics taken during the trials, it was shown that the expected improvements due to the high precision timing of electronics were realised in all areas.

Jan 1, 2007

By V Kumar, A S. Venkatesh, R K. Upadhya

The enormous iron ore deposits of eastern India are part of the volcano-sedimentary basins containing iron and to some extent manganese deposits that belong to the Iron Ore Group (IOG) of Archaean Singhbhum Craton, occurring as western and eastern limbs of a broad synclinorium. The eastern iron basin contains typically huge amounts of blue dust and powdery ores. There is a remarkable difference between the western flank ores and the eastern flank ores and the present study is part of the eastern flank ores from Noamundi. Demand for sintered fines as blast furnace feed coupled with the higher export price for lumpy ores that produce enormous amounts of fines during processing has created a situation whereby both primary and secondary fines, such as classifier fines, are being increasingly used as sintered feed for blast furnace. Systematic mineralogical and geochemical characterisation indicates that in many cases the ROM and classifier fines have to be processed to increase their Fe content and at the same time reduce their Al, Si and P contents. The fines which are already at micron sizes are amenable for beneficiation using the Mozley mineral separator and sink float test. It was observed that beneficiation was better and significantly greater by the sink float method than the Mozley mineral separator. Mineralogical and chemical studies of the fines reveal that around 80 per cent of alumina bearing minerals (gibbsite, clay and silicates) are present in the liberated form. Microscopic studies confirmed that the iron minerals are well liberated by controlled grinding to -300 mesh sizes with the beneficiation of iron ore fines and low-grade ores carried out using the Mozley mineral separator and sink float test. Beneficiation using the Mozley mineral separator increased the grade of concentrate with increasing flow rate of water as well as increase in amplitude of oscillation of the tray, but not very significantly with the increase in slope of the tray. In this method, though, iron concentration improved from 47 to 63 per cent with a recovery of around 67 per cent. It is not suitable for industry scale operation as only a small quantity of ores can be handled at a time. Beneficiation using the sink float test produced a better result with the Fe content increasing from 47 - 49 per cent to 66 - 68 per cent with a recovery of approximately 58 per cent. Initial feed Al2O3, SiO2 and Fe contents of 9.85 per cent, 15.3 per cent and 49.8 per cent respectively were beneficiated to 2.13 per cent Al2O3, 1.5 per cent SiO2 and 67.5 per cent Fe in the concentrate, with a recovery of 54.1 per cent. In contrast, using the Mozley table resulted in beneficiable contents 66.3 per cent Fe, 3.01 per cent alumina and 2.05 per cent silica. The combined alumina and silica content for the Mozley Table was >5 per cent, which exceeds the industry requirement of

Jan 1, 2005

By C Hertle

GHD-Black & Veatch (GHD-BV) have completed design and specification of the ash thickening plant at Tarong Power Station, including operation of a pilot plant. Construction of the plant is in progress and commissioning is planned for early-2004. The objective of the new plant is to convert the low concentration (lean phase) ash slurry currently generated by the power station into concentrated slurry which will then be pumped to the existing ash dam. Water recovered from the lean slurry will be returned to the power station for reuse. The drivers behind this project are to extend the life of the ash dam and to reduce water pumping costs. A maximum flow of 1000 litres per second is expected in the thickening plant. The process involves a screening phase, which removes large material that could cause blockages or equipment damage. A 50 metre diameter thickener then concentrates the screened lean ash slurry to 55 - 60 per cent w/w solids. In addition, the thickener plant will allow the harvesting of floating cenospheres (hollow, spherical ash particles) from the lean slurry. Cenospheres are currently collected from the surface of the ash dam and drained on a pad adjacent to the dam. The new system will use a surface skimmer to remove the cenospheres from the thickener and transfer them to settling ponds for further classification. The settling ponds simulate the detention on the existing ash dam, and allow entrained fine ash and slow settling cenospheres time to settle. As settling occurs in ponds, the slow settling cenospheres can be completely recovered whereas when they settle in the dam, the opportunity for recovery is lost. Cenospheres are a valuable by-product produced during the combustion process, and recycling of this material reduces the waste generated by the power station. Water recovered from the thickener drains to a three megalitre reservoir. Water is drawn from the reservoir for thickener plant service water and various other uses in the power station. The bulk of the water is used to sluice ash from the power station to the thickening plant. In the current configuration, surface water from the ash dam is reused but must be pumped several kilometres back up to the power station. The dam also holds an inventory of several thousand megalitres of water and has significant evaporative losses. Therefore the current raw water make up demand is substantial. In addition, some areas of the power station traditionally using raw water will be modified as part of this project to allow the use of recovered water, further reducing the raw water demand. The design incorporates many features of sustainable water management. By more effectively recovering water from the lean ash slurry, the amount of raw water make up required by the system will be significantly reduced. This method of water recovery provides a more sustainable and energy efficient ash-transport mechanism.

Jan 1, 2003

Background BHP Iron Ore Pty Ltd is one of the major iron ore producers in the Pilbara Region of North Western Australia. The company manages three separate joint ventures; the Newman, Goldsworthy and Yandi joint ventures and two 100 per cent owned operations, Yampi and Jimblebar. The Newman operations constitute a mine site at Newman and a 426 km railroad to Port Hedland where there is an ore processing/port site. The Goldsworthy operations currently constitute a mine site at Shay Gap/Nimingarra, a developing mine site at Yarrie, a decommissioned mine site at Goldsworthy and an ore processing/port site at Finucane Island (Port Hedland). The Yandi operations include mining and processing facilities at site and a spur line to join the Newman Hedland railroad. Jimblebar operations are scree and bedrock mining near Newman and include mining, processing and a spur line to Newman where it joins the Newman-Hedland railroad. The Yampi operations constitute a mine/port site at Koolan Island (which is presently being decommissioned). The combined BHP Iron Ore operations produce approximately 46 Mtpa of iron ore. This paper will concentrate on the processes developed and applied for the decommissioning of the Goldsworthy site. The Goldsworthy site is on the northern boundary of the Pilbara Region and adjacent to the western extremity of the Great Sandy Desert. It is located approximately 110 km east of Port Hedland (see Figure 1). The area is generally of low relief with isolated low ranges. The mine site being within the Mount Goldsworthy range area. The geology of the area is essentially Archaean granite with Archaean banded iron formation becoming dominant within the ranges. The chief soils are hard alkaline red soils. The vegetation is essentially shrub steppe with the main hummock grass species being spinifex (Triodia sp). The climate for the region is semi arid tropical. The temperature ranges from a mean low of 15¦C in winter to a mean high of 40¦ in summer. Rainfall is episodic, occurring mainly throughout the summer as a result of tropical depressions or cyclonic activity. The average annual rainfall is approximately 300 mm and annual evaporation may exceed rainfall by up to 2500 mm. Goldsworthy Mining Ltd commissioned the Goldsworthy site in 1965/66. Goldsworthy was the first iron ore operation and associated town site in the Pilbara region. The mine development peaked in 1977 with the town population reaching 1400 people. In 1982 mining ceased and the mining operations were relocated to Shay Gap, 80 km east of Goldsworthy. The Goldsworthy town continued as the base for the railing operations between Finucane Island and Shay Gap. BHP Minerals acquired Goldsworthy Mining Limited in 1990. The population for the town of Goldsworthy at this stage was around 450 people. An assessment of the Goldsworthy site operations concluded that it was uneconomic to continue the operation of the site. The decision was made to transfer the base for railing operations to Port

Jan 1, 1994