Search Documents

By Player R. L

Measurements of the rate of PbO reduction from high lead metallurgical slags were made under laboratory conditions using graphite, a CO-50%CO2 gas mixture and metallic iron as reductants. The results show a transition in rate-controlling step at low PbO contents (i.e. 6 wt.% PbO). At medium to high PbO contents in the slag, the reduction rate was found to be strongly affected by the slag chemistry, temperature and reductant type. The effect of stirring and hence mass transfer in the slag phase on the reduction rate of PbO was found to be insignificant at medium-high PbO contents. Attention is drawn to the importance of chemically controlled reaction rates at the slag-gas interface. Parallels between these results and test work on a 5 tph scale have been briefly drawn.

Jan 1, 1989

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By R J. Romañach

The theory of sampling (TOS) is now followed in the development of near infrared (NIR) spectroscopic methods for the pharmaceutical industry. TOS has been the guiding light for a two-step approach for spectroscopic composite sampling available for the development of real-time analytical methods for particulate-based industrial processes. The two-step spectroscopic sample composite has been used in the development of process analytical technology (PAT), an important regulatory initiative to improve the quality of pharmaceutical products. The two-step sample composite approach overcomes the low sample volume analysed by PAT methods; one of the key limitations to PAT implementation in the industrial production of particulate-based materials.PAT methods need to be validated demonstrating their accuracy, precision, specificity and robustness. TOS provides a deeper understanding of these validation studies which involve discrete particulate material. The validation of PAT methods is now being performed considering both sampling and analytical errors, while practically all previous method validations only addressed the total analytical error (TAE) of these methods. This has been a crucial impediment for the field of chemometrics as well.PAT is a key element of continuous manufacturing (CM) processes, which are considered an emerging technology capable of increasing the flexibility, agility and robustness of pharmaceutical processes while reducing their costs. The outflow of the continuous process is a 1D lot, and variographic analysis has been shown to discern process variation from sampling and analytical errors in pharmaceutical CM processes. Thus, variographic analysis is a process improvement tool with significant potential for improving CM processes. The possibilities for improving pharmaceutical manufacturing are enormous.CITATION:Romañach, R J, 2017. Theory of Sampling – from missing link to key enabler for process analytical technology, in Proceedings Eighth World Conference on Sampling and Blending , pp 63–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Rowland

"Ventilation models are invaluable tools for both prediction of routine daily ventilation changesin an operating mine to circuit performance expectations at the mine in 20 yearsÆ time. Arguably ventilation offi cers are becoming increasingly reliant on maintaining an accurate ventilation model with which to do their work. This paper relates to the practical assessment of the accuracy and thus ability of a mine site ventilation model to be reliably utilised on such varied tasks. The author's experience shows that in some cases the incumbent model is found to be in a state of tune that demonstrates a mine wide detailed assessment of branch resistances is simply not required. The money spent on a detailed mine wide ventilation survey that is not required would be far bett er served purchasing much needed monitoring equipment, rather than fixing something that is possibly not even broken. The term ænot rocket scienceÆ has been incorporated into the title of this paper because it appears that many practitioners believe that circuit validation is diffi cult. As long as clear att ention to detail is paid to the actual data collection process then drawing an accuracy comparison between the circuit performance and the model performance at any particular point in time, is really very simple. This paper will show a manner in which a circuit can be analysed to determine its actual state of health by using various diagnostic tools and tips. It will help ensure that subsequent work scopes to address any highlighted model defi ciencies can be more effi ciently scoped and targeted. It will hopefully remind operational people that such self assessments can easily be done æin houseÆ if the appropriate steps are followed."

Jun 1, 2012

By R Godard, J Gantumur, F Prince, C Pascoe

Resolution Copper Mining LLC (RCML) is one of the largest undeveloped high-grade porphyry copper-molybdenum deposits in the world, with an orebody at depths of approximately 2000 m beneath post-mineralisation cover. With a vision to develop a large-scale, low-cost operating mine, the project is designed as a micropanel cave with an advanced undercut.In September 2014, RCML began a study focusing on identifying and selecting the best production cases to eventually reach full production (120 kt/d). To achieve this, a methodology was developed that allows the fast evaluation of a large number of production schedules.Dassault Systèmes GEOVIA was commissioned to enhance the Footprint Finder program for batch scheduling panel cave production. The tonnage and grade schedules produced by Footprint Finder were compared to schedules developed using personal computing block caving (PCBC™). The inputs to Footprint Finder were then adjusted to achieve a reasonable correlation with the PCBC™ schedules.The enhanced Footprint Finder program was used to batch-process nearly 54 000 schedules using 20 elevations, 17 shutoff grades, four heights of draw, two different copper grades (modelled and upside), two layout refinements within the existing footprint and a variety of production ramp-up rates to 120 kt/d. The study team developed processes to analyse large amounts of data, to assist in selecting a matrix of the best schedules for detailed assessment using PCBC™. Three hundred PCBC™ schedules were developed.The detailed trade-offs between the scenarios is currently underway with promising results. This paper outlines the methodology used in evaluating the numerous alternatives.CITATION:Gantumur, J, Godard, R, Prince, F and Pascoe, C, 2016. Development and evaluation processes of cave production schedules for the Resolution copper project, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 59–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Finn, D Kentwell

Experience has shown that the E-Type multiple indicator kriging (MIK) estimation technique often works well for resource estimation in stockwork mineralisation that contains a mixture of high and low-grade mineralisation types that are difficult or impossible to separate spatially. E-Type MIK, like ordinary kriging (OK) is a smoothing estimator and where data is sparse can result in estimates of grade tonnage curves that do not reflect the true block variability at selective mining unit (SMU) scale. The rank and replace (RR) estimation methodology is designed to reproduce both local block accuracy and true block variability at SMU scale and has shown good results when used with highly skewed unimodal diffusive style mineralisation. This paper examines the use of RR with mosaic style mineralisation typically found in stockworks via a case study using real data from Newcrest’s Telfer West Dome deposit. Resource level estimation results for ordinary kriging (OK), E-Type MIK and RR are compared to close spaced grade control models as the reference reality.Results show that stationarity requirements and declustering can severely impact on the usefulness of the rank and replace technique and that it should only be used where trends are not too strong and data are relatively uniformly spaced. This does not rule out its application to stockwork or mosaic style deposits. However, in this case, the presence of trends and different data densities requires the non-stationary domain to be further broken down into sub domains for the RR technique to be effective.CITATION:Kentwell, D and Finn, D, 2017. Testing new estimation techniques – rank and replace: a stockwork case study, in Proceedings Tenth International Mining Geology Conference 2017, pp 365–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By B Wu, C Zhao, B Lei

At present, the friction factor is calculated by measuring pressure drop and airway configurations. However, the workload of on-site measurement is heavy, and the measurement results are easily disturbed by the external environment. In order to meet the need of intelligent ventilation to quickly and accurately obtain the friction resistance of roadway. Based on the important of roughness in Atkinson friction resistance formula, in this paper, fractal theory is used to characterise the 3D rough surface, and a method based on fractal dimension to describe the roughness of roadway surface and calculate the friction resistance was proposed. A computational model of friction resistance for fractal characterisation of roadway 3D rough surface was established. The parameters of the model were deduced and verified by using Nikuradse experimental data. The fractal dimension of roadway surface was calculated by 3D laser scanning data of Kailuan roadway, the established friction resistance calculation method was compared with the field resistance measurement results. It is considered that the calculation method of friction resistance based on fractal theory is reliable and can well represent the influence of 3D rough surface characteristics of roadway. The result show that the new established friction resistance formula compared with the traditional Atkinson formula in Nikuradse experimental, the average relative error is 6.874 per cent, and compared with the measured results of ventilation resistance in Kailuan experimental roadway, the relative error is 6.667 per cent. Comprehensive evaluation and analysis suggest that the new formula can well reflect the influence of 3D rough surface on friction resistance, combined with 3D laser scanning technology, the friction resistance of roadway can be calculated quickly and accurately. This research provided a reference for the key technology and theoretical development of intelligent ventilation parameter measurement.

Oct 12, 2022

By I Gipps

A vision of what the future mine involves all aspects of mining, ie orebody access, ore stoping, material transport, processing and waste material disposal. This paper examines one aspect of the future mine: rock extraction, stoping, automated for remote operation, high productivity and low cost. Concepts for the future require a re-think of the mining process and ROES® re-examines how bulk stoping of ore can be undertaken and how this should be redesigned to accommodate the possibilities that exists with remote control and automated operations.ROES® is a new mining system for underground mines and quarries utilising a shaft located close to or within the stope for the ore breakage process. The system is designed to exclude personnel from contact with production drilling, explosive placement and detonation so all of these tasks are remotely controlled or automated. Survey of the shaft, stope back and broken rock within the stope will occur, following each blast, by remote control or automated techniques. The survey will include excavation geometry, rock fragmentation, geotechnical characterisation and estimation of ore grade. Blastholes will be surveyed before placement of explosives and, with the survey data, the optimal explosive placement and blast timing will be determined with the best available information.ROES® is designed for application in open stoping or sublevel caving in disseminated, geologically defined, thick tabular or narrow vein ore bodies. Technologies developed for ROES® will also have potential applications to caving operations, reducing the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES® will reduce the stope associated development by half and will allow ore to be brought on-stream sooner and at lower cost. Other savings will flow with the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity.

Nov 22, 2011

By F Sahlström, E M. Jolis, V R Troll, E Jonsson, K Högdahl, C Harris

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Bastnäs-type magnetite-skarn-hosted rare earth element (REE) mineralisations are located in the Palaeoproterozoic Bergslagen ore province, central Sweden, and occur along a ca 100 km long belt of 1.90–1.87 Ga metavolcanosedimentary rocks. Ten different Bastnäs-type deposits have been sampled in order to assess the origin of ore-forming fluids in these systems. Magnetite and quartz have d18O values ranging from -2.3 to +1.1‰ and +7.2 to +8.3‰ respectively. Mineralised carbonates have d18O values between +5.8 and +7.2‰ and d13C values between -5.4 and -3.3‰. Temperature calculations based on the O-isotope composition of mineral pairs, combined with available fluid inclusion data, suggest primary mineralisation at ca 650–400°C. For these temperatures, calculated equilibrium fluids have d18O values that range from those typical of magmatic fluids (+6 to +8‰) to lower values (down to +3‰). Variation in carbonate O and C isotope data are consistent with interaction between local Palaeoproterozoic carbonate rocks (d18O = +12.5 to +19.6‰ and d13C = -1.8 to +1.7‰) and fluids of a magmatic origin. It is suggested that the Bastnäs-type REE-magnetite mineralisations formed as a result of reactions between local carbonate units and high-temperature, magmatic-dominated hydrothermal fluids during 1.90–1.87 Ga (Svecofennian) syn-volcanic activity.CITATION:Sahlström, F, Jonsson, E, Högdahl, K, Harris, C, Troll, V R and Jolis, E M, 2015. O and C isotope study of Bastnäs-type rare earth element mineralisation, Bergslagen, Sweden, in Proceedings PACRIM 2015 Congress, pp 439–444 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By G K. N Subasinghe

"In the design and operation of mineral processing plants, knowledge of the variability of ore properties and that of the expected metallurgical performance within the orebody is of great importance in order to avoid both production constraints due to inadequate design and less than expected metallurgical performance during operation. Of the many properties that determine the performance of downstream separation processes, such as flotation, gravity separation and leaching etc the liberation characteristics are of primary importance.Current methods of evaluating liberation characteristics of ores such as the use of Mineral Liberation Analyzer (MLA) and QEMSCAN techniques are expensive and suffer from the drawback that these tests are performed on comminuted particles at a given grind size and/or samples of product streams. This problem could be overcome by developing predictive models of liberation that can predict the grade distribution of comminuted products at any grind size based on texture of the parent rock. This paper discusses a procedure that has been developed to predict liberation using information obtained from a sample of the parent rock such as drill core, based on Barbery’s liberation models. The required characteristic statistical functions have been evaluated from image analysis techniques using scanning electron microscope (SEM) images of the parent rock and narrowly sized comminuted particles. Such information can then be used in a predictive model to predict or explain the variability of metallurgical performance at various grind sizes used in future operating plants. The model will predict not only the valuable mineral liberation but also gangue liberation, which will be useful to those who are looking to remove liberated gangue from comminution circuits.CITATION:Subasinghe, G K N, and Dunne, R, 2016. Predictive Model of Mineral Liberation for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 347–350 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By K Barbosa, G Wilkie, F Reyes, V Jokovic, C Evans

The idea behind Grade Engineering is to exploit the natural heterogeneity of an orebody (spatial, temporal) in order to divert low-value waste out of the mining value chain. Essentially, this involves rejecting material at relatively coarse particle sizes (10 mm to 200 mm). However, lack of knowledge about the inherent particle grade distributions in these coarse particle size ranges limits the opportunities for optimisation. Particle grade distributions are essential for quantifying and modelling gangue liberation and yield curves. These curves can then be used to predict the mass and value flows that will go towards the accept and the reject streams. Particle grade distribution information for particles coarser than 10 mm can be collected based on chemical assays of sufficient number of individual particles. However, for smaller particles (1 mm to 9 mm), a significantly larger number of particles is required for assays. Moreover, in some cases, the mass of individual particles is smaller than the minimum mass required for chemical assaying. Also, other quantification techniques such as automated mineralogy, eg Mineral Liberation Analysis (MLA), require extended measurement times to analyse statistically representative numbers of particles at these size ranges. This work investigates the use of 3D X-ray microtomography to fill this quantification gap at these size ranges (1 mm to 9 mm). In-house image processing algorithms are used to estimate the mineral/metal content in each particle. Particle grade distributions, as well as density distributions, are thus produced without a minimum mass requirement and with each scan providing information about tens to hundreds of particles at a time. Mineralogical data from MLA analysis, of finer size ranges, is used to inform X-ray microtomography, so a simpler 3D mineral map can be obtained using the image intensity. Chemical assay information of the scanned samples is used to validate and correct the mineral phase segmentation.

Aug 24, 2022

By G J. Showers, P Botman, A G. Hunt

Iron Road Limited (Iron Road) is currently evaluating the feasibility of producing 21.5 Mt/a of high-grade (>66 per cent Fe) magnetite concentrate from a 3.7 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate can be produced via a conventional grind and low-intensity magnetic separation flow sheet. Due to the comparatively coarse magnetite liberation size (106 µm), consideration was given to enhancing both the grind economics and coarser product sizing via gravity separation.This paper outlines the test work, flow sheet design and engineering design of a gravity beneficiation circuit (GBC) conducted by Mineral Technologies for Iron Road. The resulting circuit optimisation necessitated mass balance simulation by Iron Road’s SysCAD model to quantify the resulting changes in mill recirculation load. This included the determination of project-critical grinding power and energy requirements with and without the GBC installed into the primary ball mill classification circuit. The outcome of this work was the design of a GBC, including spirals and up-current classification, which led to a substantial reduction (33 per cent) in ball mill recirculating load and power requirements, together with a favourable coarsening of final product size due to the relatively coarser gravity concentrate. This has led to a significant reduction in project design capital and operating costs. A further benefit of this approach is increased recovery of (paramagnetic) hematite and lesser titano-hematite via gravity separation compared to an all-magnetic separation approach.CITATION:Hunt, A G, Showers, G J and Botman, P, 2015. Test work and design of a gravity circuit for Iron Road’s Central Eyre Iron Project, in Proceedings Iron Ore 2015, pp 139–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Morgan, D J. Bradshaw, S Schwarz

The characterisation of the flotation kinetic response in future mining deposits is important because the flotation response is affected by changes in ore mineralogy. Current methods for characterising the flotation response of different ore types, such as the JK floatability index test (JKFIT) methodology, require at least 10 kg of feed material. In geometallurgical applications, this material is taken from core samples. Core samples are generally obtained using specialised drills and are limited in nature. Thus, it would be beneficial to develop a laboratory technique that required less sample material but still characterised the flotation response of different ore types. The JK mineral separation index (JKMSi) is a small-scale flotation test that requires significantly less feed material (10 g of sample/data point). This study aims to investigate the JKMSi system kinetics and to validate this technique using the JKFIT proven methodology. The JKMSi flotation kinetics were manipulated by varying selected system parameters. The relationship between these parameters and mineral recovery was used to obtain floatability characteristics of the ore. For an ore sample containing chalcopyrite and pyrite, it was found that the chalcopyrite floatability parameters determined from both the JKMSi and JKFIT tests were of the same order of magnitude and the mass fractions of the fast, slow and non-floating components were similar. For pyrite, the floatability parameters were not of the same order of magnitude, but modifications to the test procedure have been identified, which may correct this.CITATION:Morgan, S, Bradshaw, D J and Schwarz, S, 2012. Julius Kruttschnitt Mineral Separation Index - Small-scale test to characterise the flotation response of an ore type, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 159-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Cooksey, Z Zhu, N Langrené, W Chen, T Tarnopolskaya

"Dynamic decision-making can significantly increase the value of mining projects and deliver better sustainability outcomes under conditions of uncertainty. Despite its benefits, dynamic decision-making is rarely used by the mining industry, possibly because of the complexity of the algorithms used to make sequential decisions under uncertainty and difficulties in visualising the optimal strategies. To achieve better outcomes in practice, decision-makers in industry would benefit from a tool that would help them to understand and implement the results of the analysis.CSIRO is developing innovative dynamic decision support tools that include an intuitive graphical display of the boundaries between the regions of different optimal decisions, which would significantly assist optimal sequential decision-making under uncertainty. The dynamic decision support tool is based on novel stochastic optimal control methodologies that can be used to optimise decisions in situations with multiple uncertain variables and decisions (Tarnopolskaya, Chen and Bao, 2015; Chen et al, 2015; Langrené et al, 2015). The types of market uncertainties that can be considered include commodity prices, interest rates and exchange rate, while the key orebody uncertainties include the reserves, boundaries between ore types and even geometallurgical parameters.The dynamic decision support tools have a number of benefits and can be used to:construct optimal operational strategies and to optimally manage resources projectsgain insight into optimal strategies under different market conditions and project settings compare expected project values under different project settings and to select the setting that provides best sustainability outcomes.This extended abstract demonstrates the use and benefits of the dynamic decision support tools using a synthetic case study of a gold mine.CITATION:Chen, W, Langrené, N, Tarnopolskaya, T, Zhu, Z and Cooksey, M, 2016. Dynamic decisions under uncertainty – a case study on a gold mine, in Proceedings Life-of-Mine 2016 Conference, pp 20–23 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

The Pilbara iron ore industry has seen rapid growth over the last five years and is now bracing itself for another expansion which will take its seaborne trade to beyond 500 Mt/a. To effectively utilise port capacities, port stockpile turnover will become extremely rapid and each stockpile built will have to be of a quality which is precise and unbiased.Sampling systems at the older Pilbara mine sites were generally designed during the 1980s and reflect the practices which were considered adequate at the time. Hence, the precision of measurement at production sites is generally unknown and quality assurance (QA) of sampling facilities falls short of what current best practice suggests. This paper suggests practical improvements in sampling practices and quality assurance, which will assist the industry in achieving quality objectives in times of rapid mining expansion.

Jan 1, 2008

By M van Kampen

The Resource Management Act 1991 has been amended on a number of separate occasions since its enactment in 1991, and has recently be subject to further amendment by way of the Resource Management Amendment Act 2005. The amendments as proposed in the Resource Management and Electricity Legislation Bill would have had revolutionary and far-reaching consequences. However, as finally enacted, the amendments are a greatly watered down version of what was initially proposed.   Nonetheless, the Resource Management Amendment Act 2005 has provided for a number of amendments that will impact on the minerals industry to varying degrees. This paper discusses in particular the changes and impact of the changes to the definition of æcontaminated landÆ, clarification with respect to the duty to consult, amendments to the provisions relating to National Environmental Standards, and to the council and Environment Court hearing process.

Jan 1, 2005

By Ju Hao L, Jian L

A joint project between the Fan Kou Mine, the Guangzhou Research Institute of Non-ferrous Metals, the Julius Kruttschnitt Mineral Research Centre, and the Changsha Design and Research Institute of Non-ferrous Metals has implemented grinding control on a circuit consisting of two primary mills and a single secondary mill at the Fan Kou mine in northern Guangdong province, PR China. This paper describes the initial design of the control system and the changes made during its implementation. The initial design was to obtain maximum throughput at a constant product size. This was changed so that the control provided a constant product density at a set feed rate. The set feed rate is reduced when necessary to prevent overloading of critical components in the circuit. The reasons for the changes in the control strategy are discussed.

Jan 1, 1993

The theme of this Annual Conference of The Australasian Institute of Mining and Metallurgy is in the form of a question: `Adding Value to our Resources - Our Future?' There are two ways of looking at this question. The first is to assume that any mineral or energy resource is worthless until it is identified, recovered and put on the market. In this sense all our current operations, be they open cut coal mines or aluminium smelters, are engaged in adding value. The question then becomes: what is the future of the minerals and energy resource industries with which we are familiar - will they grow or contract? The second way is to emphasis the value-adding aspect. The question is now one of whether or not our future depends on adding further value to resources we are currently selling.

Jan 1, 1995