Search Documents

By Sparrow G. J

The effect of polyelectrolyte flocculants on the de-watering of a tailing suspension of very fine clay was investigated.Sedimentation and filtration experiments were carried out in the labqratory to characterise the de-watering properties of the tailing. The results were used to calculate the effect of flocculant additions on the drainage and vaporation components of the de-watering of a clay suspension ponded on to a sand drainage bed.A flocculant increased the drainage rate, but decreased the volume of water that could be removed by drainage leaving more water to be lost by evaporation.The sorptivity values measured in the laboratory were used in the de-watering equation previously established for the tailing to estimate the effect of flocculant additions on the time required to de-water the suspension from 18.2 to 60 per cent solids w/w. The calculated de-watering times were found to increase or decrease depending on the volume of water removed by drainage and the prevailing evaporation rate.

Jan 1, 1980

L&M have been involved on the Shotover since 1980 when we joined Jack and Barney Ryan, who had started in 1972 with gold at $45 per ounce after a successful career as roading and demolition contractors in Christchurch. The first 85 tonne plant was a typical NZ trammel-riffle table plant with an armour plated hull for surviving Shotover floods, and was fed by a 53 tonne UH20 excavator. All this gear had to be carted in over the Skippers road on a small truck or sledge for the heavy loads. This operation was successful and generated the cash flow to sample the lower section of river and plan a second plant. To reduce fine gold losses this was planned to be a jig recovery plant and also included a vibrating screen which saved space and weight over a trammel. There are five flowlines of primary jigs and one secondary, followed by two Knudsen bowls for cleanup.

Jan 1, 1985

By N Merry, T Cocks

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and composition.   A major application of this technology is in mapping mineralogical variations within hydrothermal alteration systems. Using actual case study examples this paper introduces two approaches to using the PIMA data: 1. for directly mapping alteration systems and using the PIMA data to provide vectors to mineralisation, and 2. for establishing empirical relationships between geochemical data and PIMA spectral data. These applications demonstrate that this technology can be an invaluable tool for targeting and mapping alteration and mineralisation.

Jan 1, 1995

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The use of mining by-products for beneficial use may face approval, and acceptance barriers. This paper described the use of a sustainability framework to assess the safety, effectiveness and economic value of modified bauxite residue (Alkaloam«) for use on agricultural land in the Peel-Harvey region of Western Australia. The results indicate the merit associated with using this by-product from a safety and, private, community and environmental value perspective. They may be used to indicate the worth of pursuing any future community acceptance and agency approval process.   The use of Alkaloam« for beneficial use on agricultural land in Western Australia was first investigated over 25 years ago. Efforts to gain regulatory approval and community acceptance of Alkaloam« have had a complicated and enduring history. Understanding and assessing the value of a by-product using social and economic considerations, in conjunction with an environmental assessment, provided a more complete evaluation to that previously used.

Jun 1, 2010

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By C Morley, B Costello

In 2002 the Argyle Diamond Mine upgraded the process plantÆs recrush circuit to include a High Pressure Grinding Roll (HPGR), or High Pressure Rolls Crushers (HPRC) as they are termed in the diamond industry. HPGR have generated considerable interest over the last decade, though there are still technical/processing unknowns to its effectiveness as a primary diamond ore crusher.The upgrade of the Recrush circuit at Argyle Diamonds has gone a long way to answering some of the key questions, and thus it has reduced the unknowns to a level more acceptable to the industry.This paper focuses on the results from the HPRC at Argyle, in particular the performance of the studded wear surfaces, comparison of energy efficiency against traditional quaternary cone crushers and the resultant increased liberation. Issues that have arisen, including edge wear of the studded surfaces, will be discussed and the steps taken to reduce this issue are presented.

Jan 1, 2004

By Romanovsky N. P

The Pacific Mobile Belt (PMB) is characterized by old origin and complex evolution both in time and space. As the global structure, the PMB is a narrow tectonic region dividing two plan-etary hemispheres, viz. the Pacific and IndoAfro-Atlantic ones, the relative shifting of which defines the character of many geodynamic processes in this belt. The PMB features inhomogeneity of structure, special matter composition characteristics, sharply broken-out topography, and intensive fields. Generalized anomalies of the gravitational field closely correspond to the PMB boundaries defined by the real features, i.e. the andesite line and distribution areals of Mesozoic-Cenosoic granitoids. The belt boundary position is controlled also by seismic velocity anomalies at a depth of down to 200 km. The modern PMB deformation is defined by the left-hand equatorial shift and rotation of the Pacific Ocean counterclockwise. This rotation is non-uniform in time and of an oscillating character. The motive forces of the phenomenon are considered.

Jan 1, 1990

By M Ewart

The securing of a reliable water supply for a prospective mine in the North West Queensland Mineral Province is usually one of the most influential factors in determining the mine's feasibility. The Ernest Henry Mine required a reliable water supply to serve a demand estimated at feasibility stage to be up to 20 ML/day. Numerous options were considered before a decision was made to construct a 113 km long pipeline from Lake Julius as this was the most cost effective, reliable source of supply. The North West Queensland Water Pipeline is a multi-user, Queensland government funded project initially supplying up to 7000 ML/year of water from Lake Julius to Ernest Henry Mine, with provision made for expansion to serve future users in the region. This paper discusses the history of the pipelineÆs development, together with a summary of the scheme's design features. Environmental and licensing requirements, construction and operational issues are also discussed.

Jan 1, 1998

By Huafu L, Ruishi N, Hongnian Y, Qinglong Z, Yangshen S

The Dongshan terrane was first recognized in 1984 (Guo,et al., 1984, 1989) as an old continental crust block of migmatized granitic gneiss in the Southeast Coastal Hercynian-Indosinian orogen, and it was thought to have occured on Dongshan Island, which has an area of less than 100 km? Recent research work has shed much light on the geology of the Dongshan terrane.The Dongshan terrane is approximately 40-50 km wide and 380 km long, trending NE. It runs from the region of the mouth of the Ming River through Putian and Huian Counties, Amoy and Dongshan island of Fujian Province to Nanao island of Guangdong Province, bordering the southern segment of the coastal region and coastal islands of Fujian and eastern tip of Guangdong Province. The Dongshan terrane is divided from the Zhejian-Fujian Mesozoic Volcanic Mountain Chains by the Changle-Shaoan fractural zone, and its eastern boundary is covered under water in the Taiwan Straits.

Jan 1, 1990

By A E. C Peres, J D. Donda

With the aim of producing a concentrate with silica content lower than 1.0 per cent SiO2, laboratory experiments were conducted using a sample of the final concentrate from the Samarco iron ore flotation plant (mechanical cells circuit). The sample contained 3.08 per cent SiO2. This sample was split in two size ranges: >105 ¦m and 2. The >105 ¦m fraction, representing 23.3 per cent of the initial mass, was re-ground to 100 per cent 2 content were obtained. Considering the mass proportions of the two size fractions, the calculated silica content of the combined concentrate was 0.68 per cent, which is considered satisfactory for the objective of this investigation. The major reasons for the higher (0.90 per cent) silica content of the concentrate from the coarse fraction are the presence of silicon in the lattice of goethite and the presence of residual silicious slimes in the pores of porous hematite.

Jan 1, 2005

In-seam drilling is conducted mainly to drain coal of gas and/or water prior to development or extraction. The requirements of inseam drilling for gas drainage have mainly surpassed the technical limits of rotary drilling and are mainly being addressed by guided down hole motor drilling, albeit at a higher cost. There is an increasing application of in-seam drilling to detect geological structures or other hazards or their absence in advance of mining to reduce the risks of underground mining. Close collaboration between miners, drillers, geologists, researchers and suppliers over the last four years has seen many advances made to improve the accuracy and reliability of inseam drilling. With such developments will come closer control over the ventilation and safety of future mining under deep gassy conditions, but not without costs. The paper summarises the current applications of inseam drilling, recent technological advances and the next generation survey and geophysical sensing tools which are currently being developed

Jan 1, 1998

Late Palaeozoic and Late Mesozoic phases of widespread overprinting have obliterated most of the primary magnetization signature of the Tasman Fold Belt. Palaeomagnetic programs of a regional extent offer best prospects for identification and interpretation of such secondary magnetizations and for isolation of any remaining primary magnetization. In 1983 the BMR initiated a regionally oriented palaeomagnetic study of the Tasman Fold Belt to obtain palaeomagnetic constraints on the tectogenesis of the fold belt. Particular attention is being paid to the analysis of possible differential movements between suspect or- tectonostratigraphic terranes within the Tasman Fold Belt and the respect to cratonic Australia. Work has concentrated so far on the Cowra Trough-Molong High region of the Lachlan Fold Belt and the New England region. Pilot sampling has been carried out in the Gympie region. In addition Palaeozoic sequences are being studied from the Amadeus Basin and the Ngalia Basin to refine the palaeomagnetic reference frame of cratonic Australia.

Jan 1, 1987

By S C. Dominy

The Minerals Education Australia program is offering a tertiary learning environment for the global mining industry. The Minerals Council of Australia has instigated this initiative, which is run by the Minerals Tertiary Education Council. The program is a pioneering partnership between the Australian minerals industry, Australian governments and key Australian universities. It is designed to deliver key undergraduate and postgraduate courses for tomorrowÆs minerals industry professionals in the fields of geoscience, mining and minerals engineering and metallurgy. The flagship course for geoscience professionals is the G3 Masters program. This is a coursework-based degree supported by the Minerals Tertiary Education Council, and a partnership between James Cook University, the University of Tasmania and the University of Western Australia. These partners represent the leading-edge providers of minerals geoscience education and R&D in Australia. The G3 program provides the full spectrum of post-graduate training skills in exploration, mining and economic geology topics.

Jan 1, 2003

The Professional Standards Act responds to the growing problem of professional liability by introducing a mechanism whereby professional associations can have schemes approved. Those schemes include a cap on liability; a requirement for compulsory insurance; the development of risk management strategies; and the establishment of a complaints and disciplinary system. The Act is also designed to support and develop the concept of self-regulation by the members of occupational associations who provide services to the community by providing them with those tools. It implicitly accepts that self-regulation is preferable to statutory regulation and that self-regulation serves the interest of the community and of the providers of services. The Act arose from a review of professional liability commenced in 1988. The Attorney General's Department produced an Issues Paper, released in September 1989, which outlined in detail the extent of the problem. This was widely circulated and an extensive number of comment were received.

Jan 1, 1995

Large scale rhyolitic volcanism is an important process at some convergent plate margins because it leads to chemical differentiation of the upper.-crust and is responsible for the production of long lived near surface thermal anomalies; the Taupo Volcanic Zone is.a Quaternary example. The main features of the magmatic systems-of the zone. are the existence of large high level chambers containing homogeneous silicic magma which erupt at intervals of thousands to tens of thousands of years. Geochemical work on the deposits resulting from these eruptions has shown that with few exceptions the magmas have been remarkably uniform in their . composition throughout the history of the zone although individual batches with lifespans of the order of. one hundred thousand years can be recognised by subtle differences in trace element ratios. Basalt is a rare proportion of the rocks exposed at the surface but has played a major role as a medium for heat transfer and as an end member in chemical mixing processes.

Jan 1, 1987

By Lee G, Stitt P

The term "industrial minerals" covers a vary wide field. However in Australia this field tends to be characterised by the follow- ing: (1) Relatively low unit values. (2) Product specifications can be exacting compared to the metalliferous field. (3) Product specifications often have to be tailored to the needs of the end user. (4) Beneficiation plants tend to involve low capital outlays relative to the metalliferous field. However they often have to produce products'to a range of specifications. (5) Technology often influences what can be considered as reserves. (6) Because of low unit values industrial minerals tend to be relatively cost sensitive. This is particularly the case in regard to transport. (7) Location of deposits near to major urban areas (markets) dictates a greater pressure on ecological aspects. (8) In Australia there has been a tendency to vertical integration largely due to the restricted market available. Reserves assessment is shown to be critically dependent upon the above Factors.

Jan 1, 1979

By P Wollants, B Blanpain, R Ding

Vacuum oxygen decarburisation (VOD) is the refining process used by ALZ (Genk, Belgium) for their production of stainless steels. The process consists of three stages: oxygen blowing at a pressure of 100 mbar, degassing, and reduction of the slag with ferrosilicon at 5 mbar. The magnesia-chromite bricks used in the slag zone of the ladles suffer from acute wear. In this paper results obtained from a program to improve the refractory life span are presented. The dominant wear phenomena were identified with an electron microscopy study of bricks taken from different locations in the ladle. Concurrently a dynamic model for the vacuum oxygen decarburisation (VOD) refining process was developed. The model calculates the elementsÆ oxidation rate during the blowing oxygen stage and allows the continuous calculation of the change of the metal, slag and gas composition throughout the VOD process. From these activities a general scheme of the refractory wear was worked out and measures to improve the refractory life were proposed and implemented.

Jan 1, 2000

By Grinbaum B, Stevens G. W, Dalton R. F

Many hydrometallurgical processes produce large amounts of acid waste. This is illustrated by the copper S/X-E/W process which produces a bleed from the electrolysis tank house in the form of a concentrated sulphuric acid stream. Currently, the bleed stream is necessary to remove impurities such as iron that decreases the efficiency of the electrowinning process. However, this comes at a high financial cost owing to large quantities of make-up sulphuric acid required. A process has thus been developed with Zeneca Specialties (UK), ICI Australia and Gunpowder Copper Co at the University of Melbourne for the recovery of sulphuric acid from copper tank house bleed liquor. The recovery process uses the method of solvent extraction. Solvent extraction has the advantage of being a well-established technology in the mining industry and will reduce the environmental impact of the S/X-E/W process, as all additional chemicals can be completely recycled. A simplified diagram of the process is shown in Figure 1. Tank House

Jan 1, 1997

The importance of orebody definition and optimisation in project development cannot be overstated. Inappropriate orebody definition is the single most important reason for project under performance and/or failure. Without the firm foundation of good orebody definition, the structure of a project cannot be assembled reliably. Many factors need to be considered in the process of orebody definition. These factors are well summed up in paragraph 123 of The Institute's Code and Guidelines for Assessment and Valuation of Mineral Assets and Mineral Securities (Valmin Code). The factors range from the initial geological data through assaying, geotechnical and hydrogeological factors to mining and metallurgical considerations. There are other factors which also need to be considered including marketing and environmental factors. This paper briefly reviews some of these factors and their impact on project development. Three examples are presented where one or more of these factors have had significant impact on the development of the Project.

Jan 1, 1997