Search Documents

By S R. Grano, J Duan, T A, D Fornasiero

We have determined the experimental rate constants for chalcopyrite particles floated from a complex sulfide ore and compared them with those calculated using a recently developed flotation model. The model incorporates contributions from the efficiencies of collision, attachment and stability between particles and bubbles, as well as their frequency of collision. For these calculations, the contact angle of the chalcopyrite particles in the ore was obtained independently using a surface spectroscopic approach. The calculated flotation rate constants were in good agreement with the experimental data and able to reproduce the characteristic maximum in flotation rate constant for particles of intermediate size. The values of bubble velocity and turbulent dissipation energy derived from these calculations are relatively low and may well correspond to mean values of these parameters inside the flotation cell. We have extended this approach through the application of a property based model to an operating plant, with a satisfactory outcome.

Jan 1, 2005

By P Heppner, J Schell, R Newell

The effect of various methods of conditioning on subsequent flotation performance was reviewed, where complex interactions involving attrition, aggregation, dispersion and surface cleaning were discussed. The present study focussed on the influences of standard laboratory cell conditioning, ultrasonic dispersion and high intensity conditioning on copper mineral flotation characteristics. The effect of substituting demineralised water for the WMC plant water was also examined. It was found that higher copper concentrate grades were often obtained using demineralised water, however the use of high intensity conditioning in mill water gave the highest copper recovery and highest flotation rate constant. This process should be considered if copper grade and recovery in this section of the plant drops, especially if the drop is due to surface oxidation of the copper minerals. Other methods of conditioning (cell and ultrasonic techniques) improved the rate of copper flotation above that obtained in the virtual absence of conditioning, showing the importance of conditioning on subsequent flotation operations.

Jan 1, 2000

Ordovician metasedimenIs near the Karamea Bend and east of Ihe upper Carboniferous Karamea batholith were intruded by acidic stocks during the Cretaeeous. K/ Ar dating of two of the stocks gave 110 ± 3 millionyears whereas the batholith granite gave 290 8 ± million years. All but one of the stocks mapped lie on an approximately ENE line along which they show gradation in composition, texture, and alteration.Most of the intrusions have produced homfelsic haloes in the surrounding rocks but the hydrothermal alteration centred near the head of Questa Creek is quite distinct. Here much wider zones of alteration are characterised by chlorite, green biotite, sericite, and quartz-orthoclase in order towards the centre, though no stock crops out. Each zone of stronger alteration is heralded by "spots" containing the next characteristic mineral.It is suggested that a late phase of the intrusive period that gave rise to the outcropping stocks also gave rise to a volatile-rich intrusion still hidden beneath the head of Questa Creek.

Jan 1, 1976

By W J. Rankin

A study of refined metallic copper and nickel production was carried out using Life Cycle Assessment methodology to estimate the life cycle emissions of greenhouse and acid rain gases for these metals using data derived from the literature. Various processing routes were investigated which included a pyrometallurgical and a hydrometallurgical route for each metal. The effect of a number of process variables, namely ore grade, fuel type for electricity generation and efficiency of generation were also examined in the study. The results of the study, expressed in terms of total (or full cycle) energy consumption, Global Warming Potential (GWP) and Acidification Potential (AP), showed that the hydrometallurgical processes involving solvent extraction and electrowinning had higher energy consumptions and GWPs than the pyrometallurgical processes for both metals. Nickel metal production was shown to be several-fold more energy intensive than copper metal production. The significant effect that falling ore grades have on attempts to meet greenhouse emission targets was also highlighted in the study.

Jan 1, 2000

By S Strohmayr, R Harvey, A See

Ernest Henry Mining Pty Ltd started production in August 1997. The Ernest Henry orebody consists of two distinct parts, a complex supergene ore zone overlying a primary ore zone. The economic copper minerals in the supergene ore were chalcocite, bornite, secondary chalcopyrite and native copper while the primary zone has only chalcopyrite. The variability of the supergene zone made concentrator operation difficult and predicting metallurgical performance using mineralogy essential to establish the capabilities of the concentrator. A paper presented at the 1998 Mine to Mill Conference entitled Mineralogy Controlling Metallurgy at Ernest Henry Mining (Barnes, Strohmayr, Brindley and Munro, 1998) presented the testwork and initial plant surveys that showed that the mineralogy of the ore controls the metallurgy of the concentrator. This paper presents the data obtained from the subsequent years of operation treating both the supergene and primary ore types. A review of the actual supergene mineral distribution in feed and subsequent recoveries compared to those predicted as part of the flowsheet design is also presented.

Jan 1, 2003

Studies of the morphology of seamounts within the Hawaiian, Line Islands, Gilbert and Phoenix Seamount groups indicate that the morphology and size distribution of seamounts vary significantly from one seamount group to another. The Line Islands group appears to be the most complicated of all the groups studied thus far. This group is complicated by reactivation of volcanism, which has superimposed volcanics on sedimentary rocks. These seamounts display abundant volcanic features on their summits. Seamounts within the Hawaiian seamount chain display a marked absence of volcanic features due to the . presence of thick carbonate caps. Reef platforms and sealevel benches are very common on these seamounts but are absent from seamounts in most other seamount chains in the central Pacific. Slope angles vary regionally between seamount groups. The minimum slopes are found on Necker Ridge in the central Pacific basin. The maximum slopes are found on ridge-crest seamounts. Roughness increases proportionally with mean slope angle.

Jan 1, 1987

The Victorian State Government recognises that the extensive brown coal deposits in Victoria are one of the State's key competitive strengths for economic development. The unique properties of the coal, together with the ease of open cut mining, make it suitable for a variety of new applications. Research and development activities are centred around applications which take advantage of the natural attributes and unique properties of the coal. The high reactivity and low ash content of the coal led to its selection for the Japanese brown coal liquefaction pilot plant currently operating in the Latrobe Valley, with support from the Victorian Government and the Coal Corporation of Victoria. Research and development of new brown coal based products together with many other areas of applied and fundamental research are being conducted in Victoria by Government research organisations, tertiary insti- tutions and private industry, with the objective of establishing new indus- trial developments based on Victoria's vast brown coal resource.

Jan 1, 1989

By P O. Andersson

Mining of sill pillars is more difficult than the ordinary mining. The sill pillar mining is performed under more difficult conditions and the mining of the sill pillar itself produces more problems; failure of the rock due to high stresses, difficulties in controlling the fill above, overall stability of the stope and special requirements on the technique for backfilling. Altogether this makes sill pillar mining technically difficult and often not profitable. A project was therefore initiated with the aim to increase the mineable ore reserve by making sill pillars mineable, both technically and economically. The project aimed at developing technique for already existing sill pillars as well as planned sill pillars. For the existing sill pillars a technique would have to be developed for mining beneath unstabilised fill. For sill pillars that would be created in the future, the most suitable mining method and methods of supporting or stabilising the fill in the stope above was to be chosen within the project.

Jan 1, 1998

The growth of the mining industry around Australia over the last ten years has seen many open cut mines developed on shallow oxide reserves. Most of these have been gold operations, although there are some copper mines in the list, too. Many of these have exhausted their oxide reserves and have made the transition to underground mining to access their deeper sulphide ores. Other operations have reached or are approaching the point where the decision has to be made to go underground or cease mining. This paper discusses the issues involved in making the transition from surface to underground mining. The aim is not to discuss each of the issues exhaustively. This would take a conference in its own right. Nor is it intended to provide a primer on underground mining. Instead the aim is, firstly, to flag the issues which must be addressed when planning to make the transition from surface to underground mining and, secondly, to identify critical aspects of mine development.

Jan 1, 1997

Mine haul road design at Bougainville Copper Limited has undergone significant changes since mine start-up. Selection of 95 tonne trucks and the subsequent replacement by 155 tonne units is discussed, with particular reference to haul conditions within the mine. Changes to haul road design and construction practices are detailed which have lead to improved standards and tyre life. INTRODUCTION Bougainville Copper Limited operates one of the largest copper mines in the world at Panguna, Bougainville Island, in the North Solomons group of Papua New Guinea. The mine commenced commercial operation in April, 1972 and current planned production is 198 000 tonnes of material per day, of which 115 000 tonnes is ore averaging 0.46% copper. Annual total planned production is 72 000 000 tonnes to yield approximately 150 000 tonnes of copper with significant quantities of gold and silver. The mine operations workforce now consists of national employees up to General Foreman level.

Jan 1, 1982

Mount Isa Mines Limited commissioned the Heavy Medium Plant in August 1982. The first processing stage using Mogensen Sizer 2056 dry screens, experienced unresolvable cloth blinding problems in attempting to separate fine, damp Lead/Zinc ore at 1.7 mm. A large proportion of the fines incorrectly reported to oversize and hence to the wet preparation screens. This wet preparation screen overloading produced multiple operating and maintenance problems. The plant configuration precluded retrofitting any alternative proprietary screen. An internal Mount Isa Mines research and development programme was established to design and build a screen to achieve the required per- formance within the site constraints. The resulting ISA SIZER screen has exceeded metallurgical performance expectations. A `clean sheet' approach to the design also permitted elimination of maintenance difficulties experienced with the Mogensen Sizer. Four `production model' ISA SIZERS were installed in February 1988. The ISA SIZER screen, now fully developed is available commercially and will satisfy many screening plant requirements.

Jan 1, 1988

The Green Parrot and Reward stratabound silver-lead (copper-zinc) deposits are located in the eastern part of the Arunta Block. At Green Parrot, mineralisation is contained within a north-south striking lode horizon comprised of elongate lenses of massive garnet or calcsilicate-carbonate "lode rocks" with intercalated sericite-biotite schist and laminated biotite-feldspar schist. The "lode rocks" are increasingly calcareous to the west. The mineralisation is broadly zoned with an increase in lead content and decreases in copper and silver contents from east to west. The principal sulphide minerals are galena, sphalerite and bornite. The Reward deposit lies adjacent to a lens of massive garnet "lode rock" which is contained within garnetiferous sericite-quartz schist. Primary mineralisation consists of galena, chalcopyrite, sphalerite and pyrite. Both deposits are associated with a substantial thickening of the lode horizon which is narrow and discontinuous along strike from the Green Parrot and Reward deposits.

Jan 1, 1984

By M Ruhrberg, J Grassmann, C Bauer

Within the context of acid mine drainage (AMD) associated with mining activities worldwide there has been a tremendous research effort to determine the extent of AMD and assess the influencing factors controlling this process. However, the majority of the current approaches focus on local and regional scale case studies and do not provide a global scale picture of AMD potentials. This study attempts to develop a method aiming at a global environmental impact assessment related to AMD. To confine the complex topic this study concentrates on acidic emissions from heaps in consequence of copper mining processes. In order to pursue this approach two factors are of significant advantage: a comprehensive environmental data base of more then 600 copper sites worldwide and a method which has been developed and proven to be successful in assessing environmental impacts related to land use. Current and future research efforts focus on using this background knowledge to enable both a comparison between sites and a categorisation of sites according to emission estimates.

Jan 1, 2003

By Dawson RD

For the past 45 years, the casting of refined lead ingots by The Broken Hill Asso- ciated Smelters Pty. Ltd. (B.H.A,S,) at Port Pirie has been mainly by use of manually operated rotary casting wheels of Newnam design. This style of operation was quite satisfactory as far as standard of product was concerned, but was manually intensive and a relatively high cost operation. With most other large scale lead producers already using automated-casting equipment, an investigation which commenced in 1966, progressed through stages of enquiry, design and development until the present plant commenced trial operations in late 1973, and fully operative in late 1974. While certain features of the plant are sed on overseas practices the plant was signed and built within Australia to BRAS ecifications. As constructed it consists two almost identical casting lines each pable of producing 25 kg ingots at 25 tonnes r hour using straight line casting machines d automated stacking weighing and strapping

Jan 1, 1975

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

By Adams R. W

A commercial scale strong acid leaching plant was commissioned at the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, a member of the Pasminco group of companies, in February 1988. It was designed to upgrade the lead/silver residue product from 26% to 37% lead, thus improving the realised value and increasing overall zinc recovery. This in turn enables the lead smelter treating the lead residue to improve its productivity. The equipment consists of two 250m3 bricklined leach tanks and two 6.5m diameter stainless steel high rate thickeners operating with counter current washing at 95¦C and 120 g/L H2SO4. The present filtration and drying equipment is also being replaced. Two 35m2 squeeze action filter presses equipped with horizontal plates are being installed, together with ancillary drying equipment to ensure that the final product complies with the transportable moisture limit. The new filtration plant is due to be commissioned in mid-1989.

Jan 1, 1989

The provision of electrical power is an important consideration in project develop- ment. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of taking a supply from a power authority or providing local generation can then be considered. This requires additional definition of the prob- able characteristics of the supply. The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was possible pre- viously. The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for a number of development projects illustrate some of the aspects which influence the decisions on power supply.

Jan 1, 1986

Good morning. I am very pleased to be invited to present the Opening Address to this inaugural New Zealand Minerals & Mining Conference. It is indeed a pleasure to see so many representatives of this industry, which is so important to New Zealand's economy, present here today.   I extend a warm welcome to all delegates, particularly those from outside New Zealand. To those of you who have travelled from offshore, please closely observe our industry, and do not hesitate to ask Crown Minerals staff here for any further information you may want. I trust you will soon come to the same conclusion that my two following speakers have; that New Zealand is a good investment destination, and further that many of you will decide to invest in New Zealand's minerals and mining industry.   In New Zealand the minerals industry - minerals, coal and petroleum - together constitute an approximate $2.5 billion per year business. In broad terms this is about 3% of our Gross Domestic Product.

Jan 1, 1997

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998