Search Documents

By Warrillow C

Petroleum and mineral exploration share a common objective; to find and exploit commercial reserves of the desired commodity. Some exploration techniques are similar, others widely different.In peripheral matters such as permits, regulation procedures, land and compensation, there are many similarities. Despite this, the percep-tions and expectations of landowners and other interested parties reflect to a large extent the methodological differences between mineral and petrol-eum exploration. This can cause compensation demands and regimes to be vastly different in the two sectors.

Jan 1, 1994

By Dalzell R. W

A Conveyor Belt Fire Test Program was initiated in 1985 by the Approval and Certification Center (A&CC), Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The purpose was to evaluate the effect of entry air velocities on the burning properties of mine conveyor belts and assess fire test data from large- and small-scale tests. Belts meeting the fire-resistant standards of MSHA and agencies of other countries were tested in small- and large- scale fire tests.

Jan 1, 1988

One of the often overlooked factors affecting the capital investment decision in new or existing plants is the value of stock holdings necessary to maintain the plant. This paper puts forward a simple decision matrix on whether a part should be stocked depending on 1. the criticality of the item of equipment in terms of the effect on cash flow of its failure, 2. the lead time of the part, and 3. the stock holding value if it were Stocked.

Jan 1, 1986

Arm Royalty systems of different types are used throughout Australia by both state and federal governments to raise revenue and thus facilitate in the proper distribution of mineral wealth. Royalty systems should be neutral and equitable but by their very nature these objectives are impossible to obtain. Because of the individual nature of mineral deposits, in particular variable cutoff grades and tonnages, governments should be aware of the possible trade off between short and long term gains of the particular royalty scheme introduced.

Jan 1, 1982

The development of metallurgical training is briefly reviewed. The reasons for the current trend for Metallurgy Schools to become Schools of Materials Engineering or Materials Science are mentioned as is the role of Departments of Chemical Engineering in the teaching of extraction metallurgy. Some problems on academic staff recruit- ment are highlighted and predictions concerning future difficulties in industry getting adequately trained professional staff are made. The need for a special effort to attract and retain the best undergraduate students is put Forward.

Jan 1, 1987

As world demand for various minerals increases the mining industry in its endeavour to satisfy this demand will, eventually,look to the extraction of orebodies which previously may have been uneconomical to mine. These orebodies may be of two types. Firstly, new low grade orebodies and secondly, remnant sections of previously mined orebodies. Some of the factors relative to remnant mining operations are discussed and the potent- ial of remnant mining in providing an important contribution to future world metal production is considered.

Jan 1, 1975

By Lynch AJ

Comminution within rod mills has been investigated by izse of a matrix analysis of breakage processes. A para,~ meter, the number of breakage stages, has been introduced and cornfninut-ion within all rod mills has been expressed in terms of the¦1-number of breakage stages- and a function which des--cribes' the feed rate, mill diameter and mill speed.'The effect of variation in feed rate, feed sizing analysis and mill speed on the number of breakage stages-is-,-discussed.

Jan 1, 1963

Progress on this project will be verbally reported and a description given of the main features. A detailed feasibility study was completed in December 1986, and the Joint Venture has issued an Environmental Impact Statement. This was open for public comment until 16 February. Issues presently being considered include economic justification traffic, air quality, noise, marine fauna and flora, visual impact, heritage and construction impact. Detail design and construction is likely to commence in mid 1987, following determination of the above matters.

Jan 1, 1987

Over a four year period from 1984 to 1987, a broad range of ground conditions were experienced in recovering old workings at the Walhalla mine in central-eastern Victoria. Access to the ore zone was gained via old workings and new development. The work included: Recovery of vertical and inclined shafts. Recovery of collapsed winzes. Recovery of level drives and crosscuts. Spiling through broken ground and old mullock. Pre-grouting of caved zones. New development using small-scale rail equipment and "bobcat" Loaders.

Jan 1, 1988

By Smith S. F, Terezopoulos N. G

This paper discusses experimental results of physical scale models employed to study the stability of a pillar between rectangular roadways. A programme of laboratory investigations utilising a bi-axial test rig has been undertaken to examine the influence of various stressfields on the stability of pillars between mine roadways. The effect of pillar height/width ratio on the overall stability is studied. Observations of failure characteristics in and around pillars are discussed especially in relation to the various stressfields applied to the models.

Jan 1, 1992

By Kerkhoff G, Wood J

The maximum gas emission into underground workings can be predicted by the use of established methods which have world wide recognition. Changes in gas emission and the influence of the gas and geological environments during longwall mining at Pacific Colliery, were found.to be a typical. The relationship between longwall mining and gassy conditions is found to vary from the European experience because of the different mining and geological conditions encountered, and the higher productivity achieved, by single longwall panels in Australia.

Jan 1, 1988

By Chia A. H

This paper presents an overview of the development and operation of the PT Adaro Indonesia coal mining project. This operation is an initial two million tonne per annum mine, located in South Kalimantan, Indonesia.The paper places emphasis on some of the more unique infrastructure development and operational challenges that exist in such a remote location environment.A brief summary is also given of the Indonesian coal industry, its direction and position as a significant coal producing competitor for Australia.

Jan 1, 1992

By Will D. P

A 328 m, 2.4 m diameter raise-bored shaft has been equipped with a modular ladderway system to provide a second means of egress from Aberfoyle's Hellyer Mine in Tasmania. The modular ladderway consists of platforms, ladders and service pipes assembled at the surface and progressively lowered down the shaft. This system provides a rapid, safe and economical non-entry approach to equipping a shaft. The modular construction and single suspension allows for future extension or for reuse in another shaft.

Jan 1, 1988

By Merry N, Cocks T

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and Composition.

Jan 1, 1995

By LaBrooy S. R, Ritchie I. M

Problems with the cyanidation of copper-gold ores Copper-rich gold ores are becoming increasingly important both within Australia and overseas (Dayton, 1982; Deng and Muir, 1994; Muir et al, 1993; Sceresini and Staunton, 1991; Solis, Hefter and May, 1995; Wall, Hornby and Sethi, 1987). In Australasia alone over 30 copper-gold deposits have been reported (Muir et al, 1993). Table 1 lists several of the deposits that have been processed. TABLE 1 Examples of copper-gold deposits in Australasia. Name

Jan 1, 1997

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

By Boyd G

This paper describes the planning, analysis, design and operational experience of highwall mining based on auger drilling techniques applied to thick coal seams exposed in an opencut highwall. Being the first time such technology has been used in Australia, a large commitment to technical design and logistics planning was given by Callide Coalfields Pty Ltd. This commitment included technical and operations management and supervision, mine services, and the retention of consultants to undertake geotechnical analysis, instrument preparation and instrument installation.

Jan 1, 1991

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G Bubner, C Gaughan

Magnetite mineralisation within the South Middleback Range has been known since the early 1930s; however, it was not until 1989 that BHP (then owners of the Middleback Ranges mining leases) drilled 10 700 m of diamond core into what was then known as the Iron Duchess low-grade deposit. In 2002 a review of Iron Resources left in the Middleback Ranges and the identification of downstream processing benefits using magnetite as a primary feed source led to the commencement of an 18 000 m resource drilling program of the high-grade core of the Iron Duchess low-grade orebody (renamed the Iron Magnet deposit). This paper describes the geology, processes and procedures used since drilling recommenced in early 2003. The Iron Magnet deposit is located 53 km southwest of Whyalla in the South Middleback Range, South Australia. It is a Paleoproterozoic stratabound magnetite deposit that lies down-dip and lateral to the Iron Duke hematite deposit, hosted within the Lower Middleback Iron Formation of the Hutchison Group meta-sediments within the Cleve subdomain of the Gawler Craton. Magnetite bearing host units within the Lower Middleback Iron Formation can be divided into a æmixedÆ basal sequence, a lower iron carbonate unit, a middle iron talc unit and an upper iron silica unit, all units grading up sequence and laterally into one another. The magnetite mineralisation is hydrothermal in origin. The strongest consistent mineralisation coincides with the iron carbonate unit, and the hematite orebodies of the Iron Duke are interpreted to represent up-dip supergene enrichment of the same unit. The Iron Magnet occurs within a large-scale parasitic syncline-anticline pair on the west limb of a larger syncline. Major bounding north-south shear zones occur on the east and west sides of the deposit. Cross-cutting west-northwest, northwest, northeast and east-northeast trending faults displace mineralisation. The commencement of drilling in 2003 lead to the migration of geological and geochemical databases, re-logging and re-assaying of all old cores that intersected the deposit, updating of logging codes and procedures, and strict Qa/Qc procedures to ensure the study satisfied JORC standards. External consultants were used for auditing and bench marking. The strong geophysical responses of magnetite and the wealth of close spaced ground magnetic and gravity data already completed over the Middleback Ranges allowed for refining of drill hole targets for the drilling program. It also provided an indirect method for ascertaining magnetite grade and tonnage volumes.

Jan 1, 2005

By G Love, S Maher

In Victoria’s onshore Gippsland Basin, geology is driving brown coal developments, and geologists are key decision-makers. Prompted by volatile energy prices and the likelihood of a carbon constrained future, significant work has been carried out on the next generation of technologies to be applied to this giant resource. These include new-generation gasification technologies, coal conversion processes yielding products as diverse as diesel and fertiliser, drying technologies producing thermal and metallurgical coals and in situ conversion processes. However, coals aren’t coals, and brown coal available for new projects will have different quality parameters and mining economics from that currently mined.New projects are likely to be developed on coals with moisture contents averaging 60 per cent and corresponding low energy values. Whilst ash values will be low, averaging just 5 per cent (dry basis), this will at times approach 10 per cent, which is a level that would challenge the installed-generation technologies. Sulfur values will average 0.4 per cent (dry basis), but at times exceed 0.6 per cent, requiring technologies that address the potential for sulfur dioxide emissions. Whilst localised high levels of the fluxes iron (>1 per cent dry basis) and sodium (>0.3 per cent dry basis) would increase fouling of installed technologies, they may be suitable for selected next-generation technologies.Project viability for this next generation of technologies will be strongly influenced by mining cost, and geologists are playing a role in identifying higher-value coal. At its simplest, this is being achieved for open cut mines through regional, vertical strip ratio assessments, which are considered a first-order proxy for mining cost. Follow up assessments are incorporating mining and processing cost, coal quality penalties and product revenues. At a regional scale, it is informing the likely location and relative timing of future mine developments, as well as thinking around rehabilitation strategies, infrastructure and land-use planning.For deeper coal, factors like macro permeability, the ability to isolate seams from aquifers, groundwater chemistry, pressure temperature conditions, connection with groundwater recharge and in situ biota are being used as vectors to in situ coal conversion opportunities.Matching coal to the next generation of technologies has benefited from regional-scale geological studies of coal quality and mining economics, and has benefited from early engagement between geologists, technology developers and project proponents.CITATION:Maher, S and Love, G, 2014. Matching brown coal to the next generation of Latrobe Valley projects, in Proceedings Ninth International Mining Geology Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014