Search Documents

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20 million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1 mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010

The completion of the Hot Strip Mill at the Port Kembla works of Australian Iron & Steel Ltd., makes possible the production of steel plates and wide strip of a quality and in quantities not possible previously in Australia, and will also enable the production of tinplate to be undertaken in this country.The site chosen for the mill was a mud fiat underlain by a hard stone bottom at 5, to 801 feet below the surface; and a total area of one hundred acres was reclaimed to a level of 20 feet above the original surface.Three adjoining buildings were constructed to house the slab receiving yard, mill equipment and electric drive, together with the plate finishing line.After slabs have been heated to 2250°F at a rate of 90 tons per hour, they are transferred to the vertical scale breaker which is the first stand in the hot roughing mill. Here the primary furnace scale is first cracked and then blasted off by high velocity water descaling sprays.The next stand is the horizontal scale l;Jreaker, where any remaining primary scale is broken and then blasted off. After descaling, the slabs pass to the broadside mill, where short slabs are turned and rolled on broad side for wide plate.The next step is a slab squeezer which squares up the edges after broadsiding ready for the reversing mill. This is the finishing stand for plate and the last roughing stand for strip, which then passes to the finishing mill.The hot strip finishing mill consists of six stands with a maximum finishing speed of 2,230 feet per minute. Strip is cooled for coiling by water sprays on a hot run table and then coiled on a mandrel type downcoiler, from whence coils of hot strip are weighed and transferred by conveyor to the coil storage building.Plates are transferred from the reversing mill to the plate finishing line where operations consist of levelling, inspection, branding, cutting to width and length:INTRODUCTIONDue'to the increasing production of cars, refrigerators, washing machines and similar consumer goods in Australia, together with the increased requirements of galvanised iron...

Jan 1, 1956

By Adusumilli M. S, Subrahmanyam T. V, Rao V. D

Chance find of an economically important mineral on the sur- face and its exploitation without proper exploration work, has become the habit of humanity since the Bronze Age. The explora- tion and exploitation techniques have, however, been substan- tially improved in the technologically developed western world and system controlled major communist countries. Nevertheless, the greatest need is felt in the Third World countries where large mineral potential exists, but with inadequate investments in exploration and exploitation techniques, a handicap that has been beneficial to the more developed countries, since long. The great number of the Third World countries which are striv- ing hard to develop, need to formulate mineral exploration and exploitation strategies which could enable them to develop their resources. This requires planning and creating new concepts of ore deposit types and genetic models, rheology, economics and their innovation and integration. The following approach could help them to be economically "more independent" by the end of this century. 1. Bridging of pure and applied geology gap, and creating con- sciousness of research and development. 2. Revision of mineral resources concepts adopted to modern technological world. 3. Improved mineralogical research, and determinative miner- alogy as an important asset. 4. Creative research and establishing know-how, with philosophical base for regional exploration projects. 5. Indepth investigation into the origin and growth of earth as a system, and its importance in the association, quality, and quantity of metallic, non-metallic and energy resources con- centrations. 6. Mineral beneficiation, targets and strateties; methods of eco- nomic and improved recovery systems. Development of alter- native technology, and utilization of mineral technology strategies. 7. Theoretical and practical modelling by conventional and com- puter techniques of the existing and expected mineral resources, and mineral development. 8. Critical analysis of the status of mineral economics of the Third World and developed world with forecasts for the year 2000 based on problems faced by the developing world. 9. Minerals at cross roads of International Interdependence. 10. Philosophical, realistic, traditional and modern strategies for mineral development. The dynamic economic system opera- tion in national mineral sector.

Jan 1, 1988

By V Rajakumar, S Trang

Titanium has the potential to become the third wave of light metals used in high volume applications, following on from aluminium and magnesium. These light metals have functional attributes that can meet many of the goals needed for societyÆs transition to sustainable development. CSIRO has initiated a Light Metals Flagship to focus additional R&D efforts in support of the light metals industry. The vision of the Light Metal Flagship is for Australia to lead the Light Metals Age by reducing the costs and environmental impacts through innovative technologies for these metals. Life cycle principles will be used to identify novel technology pathways for metal production and product manufacture that are more energy efficient, less capital intensive and incorporating eco-efficient material flow chains.Under the auspices of the Light Metal Flagship, a Life Cycle Assessment (LCA) of titanium metal production was carried out with mineral sands mining of ilmenite as the starting point. Upgrading of the ilmenite to synthetic rutile by the Becher process and titanium metal production by the conventional Kroll process were the processing routes considered. Two alternative processes for titanium metal production, the FFC Cambridge process involving direct electrochemical deoxygenation of titanium dioxide, and a plasma process for producing titanium powder from titanium tetrachloride were also examined using LCA methodology and compared to the Kroll process. The environmental impacts included in the LCA were greenhouse gas emissions (Global Warming Potential, GWP) and acid rain gas emissions (Acidification Potential, AP). The Gross Energy Requirement (GER) of each process was also determined.These results for titanium, along with those from previous LCA studies by CSIRO on aluminium, magnesium, steel and stainless steel production, were used to show that despite the relatively large amounts of primary energy required for the production of these light metals, their special properties (eg corrosion resistance, strength and light weight) mean that these metals offer potential GER and GWP reductions compared to other competing materials in a number of applications, when viewed on a life cycle basis. Two applications considered in the paper are the lightweighting of motor vehicles and chemical plant equipment manufacture.

Jan 1, 2004

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

By M Stewart, J Vann, S Dunham

Geometallurgy is an emerging, cross-disciplinary field that integrates spatial models of rock properties with time-based outcomes of mining and treatment processes. Geometallurgical variables include any rock property that has a positive or negative effect on the business. Some of the more critical geometallurgical variables include recovery, grindability, throughput, power consumption, mineralogy and content of deleterious materials. These variables drive project costs and revenues in a fundamental way and thus geometallurgy has potential to positively impact on the value of strategic and tactical decisions across many mining organisations. Geometallurgical models, like traditional grade-only models are based on samples collected from the mineralised and non-mineralised regions of the deposit. The nature of some non-grade variables, particularly those that are dependent on the ore treatment processes, requires special consideration during sampling and subsequent spatial modelling. Failing to objectively consider the characteristics of variables may seriously compromise the validity of the sample selection, sample treatment, data models and the subsequent decisions. In addition to addressing the vexed question of collecting an æunbiased and representativeÆ sample, the sampling and modelling approach must consider issues of scale, both geostatistical support and also the relationship between bench-scale data and operational-scale mineral processing performance. This paper proposes a framework (the Primary-Response framework) for the classification of geometallurgical variables. This framework is designed to assist with developing sampling approaches and identifying the most appropriate spatial modelling approach. The proposed framework can also help identify the risks associated with designing, sampling and modelling of both types of geometallurgical variables. The Primary-Response framework divides variables into two categories; primary variables and response variables. How a variable is classified in this framework depends on the degree to which the variable reflects either an intrinsic attribute of the rock (æprimaryÆ) or its response to measurement processes (æresponseÆ). Depending on the classification in this framework, appropriate sampling and modelling decisions can be made to minimise the risk associated with the incorrect treatment of the variable. In particular, the authors argue that for response variables, the approach taken to building spatial models may need to be different to conventional linear averaging approaches (for example kriging).

Jan 1, 2009

By J Emslie

Newmont AustraliaÆs Callie Underground Gold Mine is located on the Dead Bullock Soak Mining Lease, approximately 600 km NW of Alice Springs, NT, in the Granites-Tanami Goldfield. Dead Bullock Soak is part of NewmontÆs Tanami Operations, which also include the Granites Gold Mine and processing plant, Groundrush Open Pit and Tanami Mill. Callie is a world class Proterozoic gold deposit; production to date is in excess of 1.7 million ounces, with an additional Proved and Probable reserves at the end of 2002 of 10.8 Mt at 6.3 g/t. Gold mineralisation at Callie occurs in thin (1 - 30 mm) steeply dipping quartz-chlorite sheeted vein system that cuts across a 40¦ plunging folded sequence of medium to fine-grained metasediments. While the vein system is highly continuous, the gold distribution is highly variable and is controlled by the interaction of lithology, alteration, structure and vein density. The mineralisation is commonly coarse-grained and has a relatively high nugget effect, consequently the orebody is problematic to estimate and shows a high degree of sensitivity to drill hole density. Resource modelling at Callie is an example of a geologically driven model that has evolved with increasing data and understanding. Lithological and structural models are employed to define domains within which the grade estimation is undertaken using multiple indicator kriging. This gradual model evolution impacted greatly on the selection of the mining method. Uncertainty in the estimation of the orebody was a significant factor that led to sublevel open stoping with cemented aggregate fill being adopted as the mining method to improve extraction selectivity. Callie often shows strong positive reconciliation compared to the mill. The mine geologistÆs face the challenge of limiting the degree of underestimation of the core of stopes whilst ensuring that stope boundaries are not conservative. This can only be achieved through the mapping of subtle geological features in order to confirm the orebody model. The increased use of the geological mapping has improved our understanding of the controls on mineralisation and has been extended into the development of new models for near mine underground exploration.

Jan 1, 2003

By J Watson

Electronic detonator technology has been under development for the last two decades. Currently, there are a number of systems commercially available with several others still under development, each with its own unique features. This technology can offer a significant advantage to the drill and blast engineer through their ability to initiate an explosive charge at the æplannedÆ time. This new technology has created huge interest within the drill and blast community and also raised their expectations to produce better blasting outcomes. In many cases, specifications (or even expectations) of desired blast results are not properly defined. Interaction between the input variables (rock mass characteristics and blast design) and results (fragmentation, throw, damage, ground vibrations, etc) and their mechanisms, or relationship to one another, are not very well defined or understood. That is why rock blasting is still considered by many as an art rather than science. With one of the few remaining variables (cap scatter) now controllable, todayÆs blaster finally has the ability to apply science to his trade. Even though electronic detonators are available and becoming more commonly used, current field practices are not always conducive to extracting or deriving the maximum benefit from this new technology. In the authorÆs opinion, the following need to be understood to derive and sustain the maximum value: clear definition or specification(s) of desired outcomes from a given blast; impact of different features in an electronic detonator system (precision, accuracy, flexibility, reliability, etc) and their impact on the desired blasting outcomes; interaction of blast design variables (energy, energy distribution, timing, blast geometry) and their impact on desired outcomes; impact of rock mass variability and quality of blast implementation on the desired blasting outcomes; and critical need to utlilise appropriate tools and systems in order to measure and quantify benefits.In the authorÆs opinion a scientific implementation process is the key to derive the benefits. This paper analyses the industryÆs preparedness to derive the benefits from this technology and proposes a scientific methodology to understand, evaluate and sustain the value from this technology.

Jan 1, 2004

By D Nourry

Optimising the blast is a major issue in the blasting business. It generally means acting on the blasting pattern (drilling, charging, detonating) in order to get a given æresultÆ. This result may either be related to economic reasons, such as the fragmentation influencing productivity, or technical reasons, for example vibrations and projections. Within the frame of the EEC funded Brite-Euram project entitled æBlast-ControlÆ, involving academic research and applied expertise, a general methodology was developed to approach such a problem and currently applied to the industrial partners of the project and final end-users of the generated results. These partners are the limestone ALZO quarry of the CALCINOR group in the north of Spain and the dolomite DMD (Dolomies-de-Marche-les-Dames) quarry of the LHOIST group in the east of Belgium. A first part of the project, over 18 months, was dedicated to establishing a clear relationship between productivity of operations from drilling to primary crushing and the fragmentation resulting from the blast. Extensive monitoring of blasting, production performance and fragmentation data was carried out and automatically collected into a database on both quarries. As expected, it appeared that excessive amounts of fines or boulders were substantially reducing productivity and thus profitability of the operation. Furthermore, an æoptimalÆ fragmentation was assessed for the quarries to run at the best (high throughput, low cost). The second and last part, for the remaining 18 months, was then dedicated to adapting the blasting practice in order to orientate the fragmentation towards a æbetterÆ one. A very common problem normally addressed by any consultant. Nevertheless, the target was not limited to solving the problem for these two quarries, but also to develop a generic method to address this blasting adaptation process and to implement it into a computerised tool. At this stage, it is then obvious that portability of the method and the system are major qualities to be looked for. This paper is aimed to present how this method was developed, how the system was implemented and how it was finally used.

Jan 1, 2001

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By Case JE

Complete Bouguer and isostatic anomaly maps compiled for Costa Rica provide new insights into the crustal structure and mineralization. Terrain corrections were approximated from the station to a radial distance of 167 km by computer using a 3- minute digital elevation model of Costa Rica and surrounding areas. Isostatic corrections, based on Airy-Heiskanen compensation, were also calculated from 0 to 167 km using the 3- minute elevation model and from 167 km to 180 degrees using combined topographic and isostatic reduction maps. Costa Rica can be divided into four main terranes based on gravity data: a Pacific coastal region, a Pacific inland area, a central region, and a Caribbean coastal region. Negative gravity anomalies along the Pacific coastal margin correlate with an offshore sedimentary basin, and large positive anomalies correlate with mafic and ultramafic igneous rocks on the Santa Elena, Nicoya, and Osa Peninsulas, and at Puerto Quepos. Pacific inland anomalies are separated from the Pacific coastal region by a steep gravity gradient, and over the Coast Ranges a major gravity low overlies a thick section of low- density sedimentary rocks. In the central region, a major gravity low occurs over a thick low-density Quaternary volcanic complex in the Cordillera Central, north of San Jose. A prominent feature of the Caribbean coastal region is an interrupted gravity low over the Limon Basin that reflects a thickening of low-density sedimentary rocks. A conspicuous gravity lineament, trending northeast separates northern and southern Costa Rica. The lineament is defined by the termination of several major gravity anomalies including those over the Coast Ranges, Cordillera Central, Puerto Quepos, and Limon Basin. In addition, the lineament correlates with other geological and geophysical data including: northeast-trending faults, the southern limit of large Quaternary volcanoes, the segmentation of the middle America volcanic belt, and a seismicity gap. This lineament may be the expression of a previously unrecognized major northeast- trending fracture zone in central Costa Rica. An important economic implication of the gravity lineament is a correlation with the termination of gold and porphyry copper deposits in Costa Rica.

Jan 1, 1987

THIS paper deals with the handling of the various materials used in the 100-ton zinc plant at Risdon, and, in view of the magnitude of the works, the configuration of the ground covered by these works, the variety of the rnaterials used, and the large quantities, a very attractive and interesting subject is opened.The works are situated on the right bank of the River Derwent, about four miles above Hobart, the capital city of Tasmania. The Risdon works cover a space of 149 acres, the area being :3800 yards long by 2800 yards wide, and the elevations vary from 6 ft. above high-water mark at the wharf and foreshore to 163 ft. above high-water mark at the power station, these being the limiting points as regards elevation which are considered in this paper. Throughout the paper elevations are given in feet above high-water mark. Fig. 1 shows a general view of the works taken from the opposite bank of the River Derwent. The wharf is clearly shown, with SS Kekerangu loading residue; behind the wharf is seen the inclined conveyor leading to the cakine bin; further up the hill is the leaching division. No. 1 haulage runs to the left of this up to a point on the left of the power station, the large reinforced concrete building at the top of the hill. Below this is the cell room, the largest building on the plant. The roasting division, not very clearly seen, lies at the foot of the main stack, and the casting division lies to the left of this, between the leaching division and the cell room. A large wharf has been construl'ted alongside the works. This wharf is 880 ft. long and 60 ft. wide. It is capable of berthing large overseas steamers, as at low tide there is a depth of :30 ft. of water. The rise and fall of the tide at the wharf is 4 ft. 6in., and the river is navigable at all states of the tide. Just above the company's wharf...

Jan 1, 1923

It is hypothesised that increasing the number of loading passes will produce a reduced range of truck payload outcomes compared with four-pass loading. The paper provides analysis to support this hypothesis. It is shown that, hypothetically, loading trucks with five or more passes will result in reduced tendency for overloading and reduced confidence interval for truck payloads that increase the confidence level of containing high end payloads within safe and commercially acceptable limits. Furthermore, increased number of passes provides for more precise bucket load spotting and so improves distribution of payloads within truck bodies. Truck-loading issues examined by the paper include: Improvement in life of driveline components and tyres. Generally tyre costs are relatively moderate; but tyres tend to become an increasingly sensitive performance/cost component as truck scale increases; Reduction of site severity fects flowing on to suspensions, truck frames and structural components generally with potential for reduced long-term repair costs; Less physical body damage due to smaller load increments; Reduced risk of non-compliance with payload limitations for safe braking standards; Increase in loading cycle times tend to increase with scale of loading machinery within the limits of a specific type of equipment (ie rope shovels or hydraulic shovels). Production increase with increased bucket capacity is, to a degree, offset by slower loading cycle times. This is particularly pronounced with front-end loaders but tends to be less noticeable with hydraulic excavators/shovels and electric rope shovels. Decrease in loading time, as a proportion of total truck-cycle time as open pits deepen and dump reaches increase. The production and cost benefits of four-pass loading tend to diminish as truck cycle times increase. The paper also discusses the implications for loading-equipment philosophy to satisfy the future needs of the industry. Cost benefits from upscaling tend to diminish as truck scale increases, so increasing management diligence and close monitoring are required to ensure that expected outcomes are realised. These truck-loading issues have been researched to assess the benefits positive or negative) of four-pass loading in practical scenarios. An attempt is made to determine whether four-pass loading is a æmust-haveÆ or merely a æmythÆ.

Jan 1, 2003

By R Crosbie, K C. Runge, E Tabosa, J K. McMaster

Flotation feed density is an operating parameter which is currently not well understood. Most models of flotation only incorporate its effect on particle residence time, but it is likely to have additional effects within both the pulp and froth phases of the machine. Test work was performed in MetsoÆs 3 m3 RCS test rig to investigate the effect of flotation feed density on metallurgical performance. The rig was operated at Rio TintoÆs Northparkes operation using flotation feed and scavenger tail. For each feed, tests were performed at different feed densities, and measurements were performed to estimate the pulp and froth recovery as well as other key flotation parameters (eg bubble size, turbulence and froth stability). Results of this test work have shown that the pulp density does affect key parameters of the flotation process in both the pulp and froth phases. Pulp phase kinetic rates decrease at high density and this is attributed to a reduction in the turbulence within the cell. Froth phase recovery, however, improves presumably because of a stabilising effect due to a greater loading of solids on bubble surfaces.There is a need for more research to be done to better understand these interactions so that metallurgists can determine the optimum flotation feed density to use at a particular operation, or within a section of a flotation circuit.CITATION:Runge, K C, Tabosa, E, Crosbie, R and McMaster, J K, 2012. Effect of flotation feed density on the operation of a flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A Turichshev

The synthetic rock mass (SRM) approach for modelling jointed and veined rock has been at the forefront of caving geomechanics research for years. A well-constructed and calibrated SRM model can capture the full rock behaviour at a macroscopic scale. Traditionally, SRM technology employed bonded particle models (BPM) due to their ability to model rock’s response to loading without prior specification of behaviour. The SRM modelling process requires the BPM to simulate intact rock and the subsequent introduction of fractures or veins by changing bonding characteristics between the particles. However, bonded particle materials have difficulty reproducing both the compressive and tensile strengths of intact rock. This and other limitations of BPM have been the driving force in exploring the potential of grain-based (2D) and bonded block (3D) models (BBM).This paper reports on recent work exploring the applicability of both BPMs and BBMs in 3D to the modelling of intact rock. The advantages and limitations of both BPMs and BBMs are addressed based on the results of numerical simulations using the PFC3D and 3DEC distinct element codes. The preliminary results suggest that BBMs are better suited for simulating intact rock behaviour than BPMs. Ongoing work aims to better qualify the applicability of BBMs under different conditions. This has significant implications for our understanding of rock mass behaviour in a caving environment.CITATION:Turichshev, A and Hadjigeorgiou, J, 2016. Simulating intact rock behaviour using bonded particle and bonded block models, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 453–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Connelly

Magnetite ores can be used to produce very high-grade concentrates that are suitable feed for the direct reduction process route but the high sulfur content of some concentrates can cause substantial environmental issues. Processing of high sulfur magnetite ore is therefore increasingly problematic for the industry. Generally, the industry demands a concentrate with <0.05 per cent sulfur and <2 per cent silica. This paper reports the outcomes of a study to produce a concentrate with the requisite low sulfur content from a sulfur-rich magnetite ore. The main findings may be summarised as follows: if the sulfur is present in magnetite as nonmagnetic pyrrhotite or pyrite, it can be beneficiated using magnetic separation and hence, monoclinic pyrrhotite is magnetic and is magnetically recovered with magnetite leading to a concentrate that is too high in sulfur. X-ray diffraction and QEMSCAN analyses revealed that the magnetite concentrate was liberated at P80 30 microns and was associated with maghemite, pyrrhotite (magnetic), carbonates and hematite with very low amounts of chalcopyrite, sphalerite and arsenopyrite. Sulfur removal using flotation was the first stage of investigation and this required flash flotation in the grinding stage followed by column flotation of the initial concentrate to generate the final concentrate. At the same time, it was observed that oxidation of the pyrrhotite had a negative effect on its flotation requiring copper sulfate to activate it. Bioleaching and concentrate leaching were also considered and achieved over 90 per cent sulfur removal but were deemed unsuitable owing to the production of highly reactive wastes and high CAPEX. Reference is made to a number of operating magnetite producers and how they manage the sulfur in feed.

Sep 18, 2023

By D Symonds, S S. Kanchibotla, L Kennelly, G McNamara, J Gaunt, B Adiyansyah

Ban Houayxai is a gold-silver mine operated by Phu Bia Mining Limited in Laos since 2012. The first two years of operation processed predominately soft oxidised ore but subsequent years were expected to process more fresh hard ore. Fragmentation of the fresh primary ores was also expected to be much coarser than for the soft oxide ores. This coarser and harder ore is expected to significantly reduce mill throughput and mining productivity. The Ban Houayxai management realised the potential downside risk when processing fresh harder ores and implemented a blast optimisation project to deliver finer fresh ore to the mill without unduly increasing blast induced dilution and damage.JKTech and the Ban Houayxai drill and blast team began a joint blast optimisation project in April 2013 to achieve finer fragmentation from fresh ores. This was achieved by modifying the bench geometry, blast patterns and applying exceptionally high levels of quality control during implementation. Blast induced ore loss and dilution was controlled by adjusting the ore blocks for blast movement. Finer fragmentation from these modified designs improved mill throughput for the hard fresh ore by 46 per cent above design on average. These new practices have been embedded in site operating procedures and have provided a quick reference ‘cookbook’ document for the engineers.CITATION:Gaunt, J, Symonds, D, McNamara, G, Adiyansyah, B, Kennelly, L, Sellers, E J and Kanchibotla, S S, 2015. Optimisation of drill and blast for mill throughput improvement at Ban Houayxai Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Cronin, R Burgess-Limerick, T Horberry, L Steiner

"Automation offers the mining industry great potential for improvements in productivity and safety. However, the experience of introducing automation in other industries has been that the full potential of new technology is not always realised. Designers are surprised, for example, to find that automation does not eliminate human errors. Unwanted and unexpected consequences also arise if the introduction of automation fails to consider how people will adapt to the new technology. A focus on the technical aspects of automation is necessary but not sufficient for success. The potential for improvements in productivity and safety promised by automation will only be achieved if the joint cognitive system that emerges from the combination of humans and automation is designed to perform the functions required for system success. This case study describes the human factors issues associated with the introduction of automation generally, and describes a case study of the successful implementation of loader automation at Northparkes mine.Information obtained through a site visit and interviews with operators, safety staff and the project manager revealed the following strategies for successful design and implementation of the automation system: involve the people who will be impacted encourage constant communication between operators and designers provide operators with essential information avoid providing non-essential information provide the operators with flexibility empower operators to take action take advantage of the new possibilities automation provides.CITATION:Burgess-Limerick, R, Horberry, T, Steiner, L and Cronin, J, 2017. Mining automation human-systems integration – CMOC-Northparkes case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 93–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By O A. Aladejebi, S Mitra, T Singh, D J. Pinson, S, S J. Chew, T Honey

Currently, many commercial sinter plants are exploring the potential addition of high-grade iron ore concentrates to improve the sinter grade. A better understanding of the ore blend, granule behaviour and green bed properties is critical to making this change and maintaining productivity in the sinter plant. This study compared the performance of a laboratory scale granulation drum to a commercial scale unit. The blend used was an Asia-Pacific style sinter blend containing iron ore concentrates. The operating conditions of the two granulation drums (laboratory and commercial scale) were fixed at the same Froude Number (0.00337), space factor (15 per cent) and residence time (4.5 mins). The granules were characterised by measuring their mean size, size distribution and green bed voidage. It was found that the laboratory scale granules were representative of commercial sinter plant granules at similar moisture content. When the moisture was fixed at ~6.9 per cent, granulation time had no significant effect. A further fundamental investigation was undertaken to measure the water holding capacity and intra-particle porosity of the individual ores used in this study. The kinetics of water absorption were measured which showed that water absorbs quickly into the ore particles within the first 60 seconds, slowing down until final saturation was attained after six hours. A linear relationship between the water holding capacity and intra-particle porosity was noted for different ore particle sizes. The results of this study provide a baseline understanding of the current commercial sinter blend and encourage exploring the specific effect of increasing the proportion of ultrafine concentrates in sintering in a future study.

Sep 18, 2023

By D Connelly

The Iron Road Limited Central Eyre Iron Project (CEIP) area, located on the Eyre Peninsula of South Australia, covers extensive Archaean iron formations that occur as coarse-grained magnetite bearing gneiss. The cumulative strike length, estimated from aeromagnetic data, is at least 95 km.The project is located in a grain growing area 185 km west of the existing iron ore and steel making operations of OneSteel at Whyalla. A narrow gauge railway built to transport agricultural products to the deep-water port of Port Lincoln, 175 km to the south, traverses the project area. A number of well-serviced rural townships are located nearby. Current activities include resource expansion drilling, extensive metallurgical test work, community consultation and a Prefeasibility Study (PFS) that commenced in April 2010.The PFS has encompassed the Central Eyre Iron Project, comprising the three significant iron occurrences (Warramboo, Kopi and Hambidge) and was completed in early 2011. Extensive test work programs and metallurgical modelling confirmed viable process options for the project, using simple off the shelf processing technology.Preconcentration by coarse cobbing yielded promising results, and is the key to reducing not only the capital expenditure but also the operating cost, in particular the power cost, which is the highest operating cost component of a magnetite benefi ciation plant. The ore is also amendable to high pressure grinding rolls (HPGR) processing. This offers a potential for further reduction of the energy requirements.Test work also confirmed that a high grade blast furnace quality concentrate (~68 per cent Fe) can be produced at a relatively coarse grind (P80 106 µm).

Jul 11, 2011