Search Documents

At its Port Kembla Plant, Australian Fertilizers Ltd. manufactures Superphosphate and other Phosphatic Fertilizers.Phosphate Rock is received from Nauru and Ocean Island. It contains water insoluble tri-calcium phosphate, Ca3(PO4), to an average of about 86%.It is crushed to pass a 20-mesh x 26-gauge woven wire screen, and is then treated with Sulphuric Acid to give the product Superphosphate with a water solubie prosphate content of 20.5%, estimated as P205. Sulphuric Acid is made by the chamber process. Three sets of chambers are installed, on,e five-chamber set of timber frame work construction and the other two of more recent date, each with four chambers of steel frame work construction. A fourth chamber set is now being built.Sulphuric Acid is delivered for use. at about 70% H2S04, the strength depending upon the rock used.Mixing - The crushed rock and sulphuric acid are mixed in weighed and measured proportions respectiyely in one-ton batches in revolving cast fron pans, mechanically stirred. The mixture, while still slurry, is run into a closed horizontal concrete cylinder (den) where, with the completion of the chemical reaction, it rapidly sets as Superphosphate.Approximately fifty batches are required to fill a den. When full, the den is opened ana the mass cut out by a revolving cutter. The product is elevated and conveyed to any required position in the Superphosphate storage shed, where it dries and matures.Despatch - As required, the Superphosphate is excavated by a two ton grab and conveyed from the matured "dump" to bagging units where it is disintegrated, screened and bagged at twelve bags to the ton. The filled !Jags are closed by machine and delivered to railway trucks immediately.Mixed Fertilizers - Sulphate of Ammonia, Sulphate and Muriate, of Potash, and Blood and Bone are mixed with Superphosphate and thoroughly incorporated to give different mixtures to meet special plant requirements.

Jan 1, 1938

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002

By D O’Dea, B Godel, T Honeyands, G Evans, T Harvey

The pores within iron ore sinter are important for producing a high quality material that is strong and easily reduced. The complementary methods of mercury intrusion porosimetry (MIP) and X-ray computed tomography (CT) were used to characterise the structure of industrial and pilot scales sinters across a wide range of pore sizes (3 nm to 100 µm for MIP and 50 µm to 5 mm for CT). The inhomogeneous nature of sinter and the variation in the measurements make it difficult to compare samples. The generalised additive modelling (GAM) approach, using the open source statistical software package, R, has been applied to highlight where there are peaks in the concentration of pore sizes. Importantly, the shape of the GAM-fitted function and the heights of the peaks show statistically significant differences between samples. For the samples investigated, the GAM-fitted functions for the MIP volume distribution of pore diameters were found to have a common set of distinctive peaks at 0.005, 0.6 and 20 µm. The GAM approach was also applied to the X-ray CT measured pore wall thickness, highlighting a single peak whose position varies between samples. The cause of these distinctive peaks and their implications for sinter quality are discussed. Correlation was found between the volume in peak 1 (0.005 µm) and the concentration of primary hematite. No correlation was found between the pore wall thickness and the strength of the sinter, suggesting the composition of the pore walls may be more important. Future work will focus on small-scale sinters produced under tightly controlled conditions to study sinters with a wider range of quality values.CITATION:Harvey, T, O’Dea, D, Evans, G, Godel, B and Honeyands, T, 2017. Highlighting key features of the pore structure of iron ore sinter using mercury intrusion porosimetry and X-ray computed tomography, in Proceedings Iron Ore 2017, pp 39–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R J. Goldfarb, A B. Christie, D I. Groves

Small orogenic gold deposits have the same deposit-scale geological and geochemical features as those that characterise giant orogenic gold systems (>16 Moz Au). Therefore, a broader-scale approach is needed to identify the critical controls on giant deposits and their disproportionate distribution throughout time and space. Ages of giant gold systems cluster around well-defined periods of lithospheric growth at continental margins, and it is orogen-scale processes during these Late Archaean, Early Proterozoic and Phanerozoic times that determine gold endowment of a province.   A critical factor for giant orogenic gold provinces appears to be asthenospheric upwelling at the time of gold mineralisation to most effectively transfer the thermal energy required to initiate and sustain high hydrothermal fluid flux. The extent of this fluid flux should be related to thickness of the lithosphere beneath a province at the time of gold mineralisation, such that giant gold deposits are much more likely to develop in orogens with oceanic or thinned continental lithosphere. A proxy for the latter is likely to be a short premineralisation crustal history such that thick subcontinental lithospheric mantle was not developed. Conversely, orogens with protracted premineralisation crustal histories are more likely to have a thick subcontinental lithospheric mantle, which is difficult to delaminate and, hence, such provinces will normally be poorly endowed. The nature of the lithosphere also influences the intrinsic gold concentrations of potential source rocks, with back-arc basalts, transitional basalts and basanites enriched in gold relative to other rock sequences. Thus, segments of orogens with thin lithosphere may be defined by conjunction of giant-scale fluid flux through gold-enriched sequences.   Although the nature of the lithosphere plays the crucial role in dictating which orogenic gold provinces will contain one or more giant deposits, the precise siting of those giants depends on the critical conjunction of a number of province-scale factors that control fluid conduits, traps, and seals in tectonically and lithospherically suitable terranes within accretionary orogens.

Jan 1, 2005

By M Miller

Operators of nickel laterite pressure acid leach and gold pressure oxidation technology frequently employ a series of steam condensing heaters to preheat the leach feed slurry. The heaters are an economic pinch point û although the thermal performance of the heaters is critical to overall process viability and operating cost minimisation, they are also a significant capital item and must be sized accordingly. Despite this, discussions of the factors underlying heater design are conspicuously absent from technical literature, and existing operations feature a conflicting range of heater sizes and configurations. This variety would suggest that at least some of the chosen heater designs are oversized. As part of its detailed design stage, the Ravensthorpe Nickel Project (RNP) constructed and tested a pilot plant heater to develop an understanding of the heating process and to ensure that the RNP heaters were appropriately sized. This testwork used RNP slurry at design density and viscosity on a 450 mm diameter, 6500 mm high column. The pilot plant testwork demonstrated the intrinsic efficiency of the direct steam condensation heating process, which was essentially independent of slurry density and viscosity. Presence of non-condensable gases in the steam phase decreased the heat transferred in certain circumstances, but heater performance remained consistent with thermodynamic limitations. Stagewise heat transfer within the column was rapid, and suggested either a very high slurry surface area or excellent heat transfer within the slurry phase. While the testwork did not set out to distinguish between these effects, physical evidence pointed to droplet formation in the inter-tray shower zone, giving a high heat transfer area. For scale-up purposes, the key facts were that the heat transfer rate was not limited by using high viscosity slurries and heaters could be designed using the principles applied to the smaller of those in existing operations. This paper discusses existing slurry heater designs, the current understanding from open literature, the pilot plant testwork, results and analysis, and scale-up to commercial sized equipment.

Jan 1, 2005

DIVERSITY There are plenty of examples to show that diversity has been the fundamental downfall of many organisations, particularly when you consider the international position. What about core business, the return of companies to key competence directions and market focus. The stockmarket for instance defines groups and companies in key groups of core business. The expectation is that companies toe the line and do not diversify across their areas of defined expertise. In essence, the market has given notice that the requirements are to focus and stick to our core business. So what right does the conference have to suggest that diversity is the key to prosperity. Hasn't the organiser read the book, studied the history, listened to the market - obviously not. Have they got it wrong, My feeling and belief is no - the organisers have got it right. However, the matter is not as simple as first perceived. What is Diversity, or Diversification as I would prefer? Is it a product position? Is it a geographic position? Is it an expansion or change in services offered? Does a gold mining company diversify into copper or diamonds or aluminium or nickel? Does a gold miner in Australia diversify into China or Kazakhstan or West Africa? How do the two relate? They don't. A successful company will always possess a 'core competence' not so much a 'core business'. The best example of this is the service company extraordinaire - McDonalds. They don't sell hamburgers or french fries, they sell a service, a convenience, a lifestyle. The core business is hamburgers and if McDonalds were to diversify further into new styles of hamburgers, I suggest to you they would fail. But if McDonalds were to diversify into other products based on their 'core competence', provision of service, then I would suggest to you they would be very successful. The service procedure, service machine, service system, the formula, stava the rnnetant the nrnrlnrte -

Jan 1, 1996

By P Licence, M Stevens, P Atkinson, J L. Mauk

The Rahu and Ascot epithermal Au-Ag prospects are two km north of the Karangahake deposit in the Hauraki Goldfield, and all occur in an approximately 6 km2 north-south elongated magnetic æquietÆ zone. The prospects are hosted by andesitic flows, lithic-crystal tuffs and local sedimentary rocks; local silica sinter occurs at Ascot. These host rocks are intensely altered by quartz, adularia, albite, chlorite, pyrite, illite, interstratified illite-smectite and calcite. Several minerals show zoned distributions, such as widespread adularia that overlies more localised and deeper albite. Illite is the only dioctahedral phyllosilicate in several drill holes, but elsewhere it forms a shallow carapace underlain by interstratified illite-smectite with 50 to 90 percent illite. Veins are common with quartz dominating near the surface and calcite becoming more abundant at depth. Local laumontite-calcite veins also occur. Pseudosecondary and secondary fluid inclusions in quartz and calcite at Rahu and Ascot have homogenisation temperatures (Th) that range from 162¦ to 268¦C and 128¦ to 243¦C, respectively. Most inclusions have trapped dilute fluids with salinities of less than 1.9 weight percent NaCl equivalent, but 20 percent of the inclusions have salinities of 2.0 to 10.5 weight percent NaCl equivalent. Calculated paleowater table elevations suggest that the water table at Rahu occurred at 440 m above sea level (asl). At Ascot, silica sinter formed from discharging geothermal fluids (=100¦C) at the paleosurface at ~135 m asl. However the sinter also contains comb quartz with pseudosecondary inclusions that have a Th average of 229¦C, corresponding to a paleowater table at ~430 m asl during inclusion entrapment. Taken together, these results suggest that the Ascot sinter was buried by approximately 300 m of cover material during a major volcanic or tectonic event, and that subsequent hydrothermal fluids formed veins and alteration at Rahu and deposited comb quartz at Ascot.

Jan 1, 2007

Kumba Iron OreÆs Sishen Mine is one of the worldÆs largest iron ore mining operations situated in the Northern Cape, South Africa. It produces 29 million tonnes of iron ore products per annum using a dense medium separation (DMS) beneficiation process. Kumba is currently commissioning the Sishen Expansion Project (SEP) which will produce a further 13 Mtpa product through a jigging beneficiation process. The products from the Sishen Mine are highly sought after and consumed by domestic and various European and Asian customers. During beneficiation iron ore slimes are generated and discarded as waste material to the slimes dams. A study was initiated in 2005 to investigate processes to beneficiate these slimes to saleable products û prompted by the current high demand for iron ore products and the high grade in the Sishen slimes thickener underflow of approximately 54 per cent Fe. Initial laboratory scale test work indicated that a 66.5 per cent Fe iron ore concentrate could be produced from the Sishen slimes thickener underflow through a process of classification, two stage wet high intensity magnetic separation (WHIMS) and five stage flotation. This process, however, did not produce the desired results during pilot plant testing and numerous alternative process routes were investigated. The process that did achieve the desired product grade of 66.5 per cent Fe at economically feasible product yields consisted of two stage WHIMS using SLON magnetic separators. Results achieved indicate that the thickener underflow slimes can be upgraded from 54 per cent Fe to 66.5 per cent Fe at a product yield of ca. 40 per cent. Product yield could be increased through the further beneficiation of the SLON tails. The Sishen slimes thickener underflow production rate is ca. 3 Mtpa û resulting in a potential concentrate production of ca. 1.2 Mtpa. The slimes concentrate will be fed to a pelletising plant that will produce 66 per cent Fe pellets destined for domestic and or export markets.

Jan 1, 2008

By T Mizuta, H Satoh, M Ogasawara, M Miyata, M Fukuyama

The Miocene Chichibu granitoids associated with the Chichibu skarn deposit are divided into North Body, South Body and Daikoku altered stock. Orebodies of the Chichibu skarn deposit are mainly distributed in the north-western part of the North Body and Daikoku altered stock. The North Body consists of magnetite-series granitoids ranging from tonalite to granodiorite and to monzogranite from the margins to the centre of the intrusion. The South Body consists of tonalite and granodiorite, and most of these rocks are also classified as magnetite-series granitoids. The Daikoku altered stock consists of a quartz diorite porphyry. The SiO2 contents of the granitic rocks of the North Body and South Body range from 61.6 to 70.7 wt per cent. During magmatic differentiation, Cu, As and Zn contents in fresh granitic rocks of the North Body and South Body increase with SiO2 content up to 63 wt per cent SiO2, and then progressively decrease with increasing SiO2 contents as SiO2 exceeds 65 wt per cent. Estimated pressure for the emplacement of the granitoids is about 0.5 kbars. Cathodoluminescence studies on quartz from those granitic rocks show that vapour rich two-phase fluid inclusions tend to occur in the core of quartz crystals, while halite-bearing poly-phase fluid inclusions occur in the margins of quartz crystals. The distribution of fluid inclusions suggests that fluid composition changed from low to high salinities during the growth of magmatic quartz crystals. Texture showing quartz crystals with an oval shape enclosed by radial aggregates of a mixture of fine-grained quartz, plagioclase and K-feldspar composing the groundmass of the monzogranite also suggests a pressure decrease during solidification of North Body. These findings show that high salinity fluids were present during magmatic differentiation and that Fe-Cu-Pb-Zn-Au-Ag skarn mineralisation of the Chichibu deposit was possibly associated with these high salinity fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Ok Tedi Mining Limited commenced construction in mid-1981 of facilities and infrastructure to mine and process gold ore at Mt Fubilan in Papua ew Guinea. Production ofgold began more or less on schedule in mid-1984 although design capacity is yet to be achieved. Due to geotechnical problems, two important items of infrastructure, hydropower and permanent tailings disposal, are not yet in place. Current low metal prices make it likely that copper facilities will be postponed.The deposit compriscs a leached gold capping overlying copper sulphide porphyry mineralisation containing significant gold and molybdenum. Mining is by open pit methods. The soft leached capping gold ore is ripped and dozed, loaded by hydraulic shovel and trucked to a dump pocket. After passing a large semi-autogenous mill of nominal capacity of I, I00 tonnes per hour, the ore is treated by the carbon-inpulp process, with a gravity circuit to recover coarse gold. The final product is 12 kg dore bullion bars.At present, all tailings are detoxified with hydrogen peroxide; after cycloning, the coarse fraction is stored, and the slime fraction discharged into the river system; expected environmental impact is acceptable. Investigations for a suitable dam site for a permanent tailings system are still underway.Peak 'I. hour power demand for Stage I is 17 MW, presently supplied by a diesel alternator power station and a 2 MW mini hydropower plant.Initial access to the base camp at Tabubil was only by air. Eventually a road was pushed through 134 km from the river port at Kiunga (where port facilities have been constructed) and a further 23 km to Mt Fubilan.Roads are constructed of compacted gravel and crushed limestone generally underlain by geofabric. Eight major steel bridges were built.The town of Tabubil has been established, including housing, airport, shops, offices, schools and all facilities.Environmental studies have been extensive and a detailed monitoring program is maintained. Ok Tedi Mining Limited is making considerable efforts to train Papua New Guineans and to foster local business.

Jan 1, 1985

Historic mining across the Bendigo goldfield reached an average mining depth of 750 m over an area of about 16 km by 4 km, with two shafts exceeding 1400 m. Mining ceased in the mid 1900s due in part to increased dewatering and ventilation demands. Water extraction technology of the day, combined with multiple mine ownership, did not allow uninterrupted and thus economic mining activity to prosper. Today Bendigo Mining Limited (BML) is targeting gold-bearing reefs beneath the water-filled historic mine workings. To ensure mining activity can proceed without the risk of water inrush, historic workings are being dewatered by submersible pumps in historic shafts and through a series of underground drain holes intersecting old workings. Due to the high heads involved, individual drain hole development requires rigorous safety control implementation and assessment prior to drilling. Water extracted via drain holes is pumped to the surface through a series of pipe lines and rising mains in conjunction with two staged pumping stations. Both stations are equipped with high-speed centrifugal pumps, each capable of pumping 40 L/s at a static head of approximately 300 m. BML, which operates beneath and within a large city, is confronted with unusual environmental and social challenges compared to many within the mining industry. The raw mine water, which contains elevated salt levels, is piped through residential areas and must comply with strict controls to prevent impacts on the surrounding environment. The final delivery point is BMLÆs water treatment plant at the north end of the city. The water treatment plant utilises chemical pretreatment and reverse osmosis. It is able to process 7 ML of mine water per day at full production. The product is approximately 5 ML of reusable irrigation quality water, which is made available to the Bendigo community for public gardens, sporting facilities and rural irrigation. The 2 ML of brine is directed to a purpose-built evaporation pond facility located 7 km north of the water treatment facility.

Jan 1, 2008

By J Araya, O Leiva

The mine evaluation process, composed of the designing, planning and valuation of a mine project, is, among other variables, based on an estimated orebody model. However, as the information from the drill holes is limited, it is impossible to know with certainty the mineral content in each block within the estimated block model. Consequently, uncertainty about the value of metal grades, or other geological attributes, arises because of the lack of information at unsampled locations. This is one of the reasons why, in any mine operation, there will always exist a divergence between estimated and real values. Cut-off grade optimisation is the process used to determine the operating mining strategy (long-term production scheduling) that will maximise the total profit value (normally referred as the net present value (NPV)) of a mine operation. This is done by defining a dynamic cut-off grade policy which is constrained by the production capacity of the mining, mill and refining.Real options is a type of contract, written on real assets such as mining, oil and other natural resource industries, that gives you the right but not the obligation to exercise the contract. It is based on operational and managerial flexibility, which allow mine decision makers to react to either good or bad operational and economic events in the future. But, what do geostatistics and cut-off grade optimisation have to do with the application of real options in a mine project evaluation process? The objective of this paper is to answer the previous question by showing how geostatistics combined with cut-off grade optimisation are key tools for corporate/managerial decision makers, which allow them not only to analyse the resource/reserves of their projects, but also to generate operational strategies that can maximise project value by minimising the downside risk due to ore tonnes and grade uncertainties, while achieving operational and physical constraints such as mining and processing capacities. A real copper grade open pit mine project is used as a case study.

Sep 26, 2011

By Schofield D, Denby B, Stout F, Moli A

This paper documents the development of a user-friendly computational program, which has been constructed to assist the mine ventilation engineer in the optimal design and operation of methane drainage ranges. In the past, many computer tools for ventilation engineers led to the development of `research systems'. These computer systems, although developed with the needs of the industry in mind were due to a combination of inexperienced programming methods and the availability of suitable user interface software not easily accessible to the practising engineer. Recent developments in computer hardware and software (particularly windows based graphical user interfaces) mean that engineers no longer need to dedicate large amounts of valuable time to become familiar with often complex items of software. The authors of this paper intend to demonstrate a practical system which successfully integrates complex mathematical models, an easy to use interface and knowledge based techniques. The graphical interface guides the user to draw on the screen a mimic diagram representation of the methane drainage network. The user is prompted, during the construction of the drawing, to input the information and data required by the calculation and knowledge based procedures. The computer program then calculates all of the flows, purities and pressures throughout the network. Given reliable measured data from an existing range a comparative analysis can be performed between the predicted and measured network flow data. A knowledge-based system may utilise this analysis to either update the operational status of the network or suggest either a reasoned maintenance or remedial strategy to improve the performance of the drainage system. The development of the OMEN project has been carried out at the request of the Midlands Group, British Coal Corporation, Edwinstowe. The system is about to be field tested at a number of mines. It is hoped that when this paper is presented that the system will be used at both Group and mine level.

Jan 1, 1995

By Y Lin, B J. Seligmann, M Hassall, S Micklethwaite

For multi-site mining companies, checking the quality and consistency of the data recorded in risk registers is important for confirming how well mine safety management systems have been implemented. However, this task is complicated by the differences in scope of the site, their particular nature, the complexity of the operations and many other factors that can introduce nuances to the characteristics of the risk registers. We present here an application of a technique called Causal Network Topology Analysis for comparing the quality and consistency of risk registers. By quality we refer to, for example: - missing causal relationships between risks - location of missing controls - focus of risk treatment strategies: prevention versus mitigation controls. By consistency we refer to how causally interdependent are the risk events. There are often causal interactions between the lines of a risk register that mean that the likelihood and consequence scores that are applied to each risk event are not independent. We measure this degree of interactions by: - proportion of independent scenarios per register - efficiency of risk treatment strategy comparison. This approach can indicate quality and consistency differences between registers irrespective of the actual details of the site or operation. This occurs by comparing aspects of the structure of a causal network extracted from how the risk events, causes, controls and consequences causally interact. In this work we compare pairs of registers to demonstrate the approach.

Apr 16, 2024

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By K J. Ward, C N. Hatton, J Scalia IV, C A. Bareither, D L. Spencer

The mining industry is experiencing change in the governance of tailings facilities (TFs). Guidance and regulations across many jurisdictions contribute to this amorphous change. The Canadian Dam Association, Mining Association of Canada, Australian National Committee on Large Dams, and the Global Industry Standard on Tailings Management, produced by the International Council on Mining and Metals, are establishing guidelines for more rigorous industry governance. Evolving guidance regarding TFs is developing concurrently with a shortage of experienced tailings engineers, which adversely affects the resource base available to support new governance. This paper presents an updated semi-quantitative estimate of the impending resource shortage of qualified tailings professionals. Updates are provided herein for the estimated number of TFs worldwide, which included available data on active and inactive TFs, as well as the estimated labor resources required to service these facilities. The tailings labor shortage is discussed in the context of academic and professional training currently available to increase the quantity of trained personnel. This paper represents a discrete moment in time as contributions to the available information and inventories accessed continue to improve, but as of today are incomplete. However, the data and information included provide insight into the resource deficiencies currently within our profession, training and education opportunities to address those resource deficiencies, and a snapshot of a recent professional training course offered on mine tailings.

Jul 1, 2021

By Kentwell D. J, Cusak C. J, Harvey-Kelly F. E L, M D. Goodz

The Morning Star Gold Mine presents an example of a prolific operation with considerable historical records, mine workings, drill hole logs and countless plans from greater than 20 adjacent mines which have now been consolidated to form the current project. Implementation of 3D computer modelling in the planning stages has provided an additional tool to integrate and refine geological models as a guide to some exploration strategies. It has allowed for a re- interpretation of the host rock units, dimensional constraints, new exploration extensions and provisional resource modelling. The initial consideration of this project was to integrate 135 years of mining history into a single database. Each historic mining area had an unrelated mine grid, often established parallel to the long axis of their main stopes; some were based on magnetic or true north. Survey plans were in chain, imperial or metric units. Through the manipulation and rotation of old grids, previously unrelated mine workings began to form continuous mineralised zones, with unmined portions still remaining in between the existing development. Furthermore the current drillhole database of >433 holes showed numerous confirmatory intersections of new mineralisation. A series of tiered tables were created within a relational database to derive guidelines for assessing data to attribute a Mineral Prospectivity Value [MPV] based on key indicators of mineralisation. Indicator logging now forms the basis of geological descriptions.

Jan 1, 1997

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

By A E. Petts

Record iron ore prices and a renaissance of infrastructure in the Pilbara have Flinders Mines poised to move from explorer/developer to an iron ore producer. The potential of the company’s Pilbara Iron Ore Project was first highlighted by the announcement of Rio Tinto’s Caliwingina North deposit to the north and the Fortescue Metals group’s Serenity deposit in the southeast. The success of Flinders Mines’ exploration has been based on incorporating landscape studies into an existing geological framework, and using this to understand the iron-rich materials that were emplaced during the Tertiary. The development of the Delta and Eagle deposit resource models highlights this process. There are three main mineralisation styles at the project; detrital iron, channel iron and bedded iron deposits. They have textural and mineralogical similarities with comparative deposits in the region. Gaining an insight into the geological processes unique to detrital iron deposits and more distal channel iron deposits has been important to understanding the geometallurgy of the mineralisation. The model sits comfortably with other regional oregenesis models and allows a contextual framework to be developed around the timing of deposition of the Fe-rich detritus and pisolitic nodules that dominate the deposits. The exploration model also allows Flinders to explore more effectively for bedded iron mineralisation developed prior to, and since the development of the Tertiary weathering landscape.

Jul 11, 2011